diff options
author | Stephen Rothwell <sfr@canb.auug.org.au> | 2017-02-09 15:08:51 +1100 |
---|---|---|
committer | Stephen Rothwell <sfr@canb.auug.org.au> | 2017-02-09 15:08:51 +1100 |
commit | 3867ac7e86a24791a7afe30d31d53fe2c76723c2 (patch) | |
tree | a5567e52ec999ab6f668464d6ca9ac01dff4a3ca /Documentation | |
parent | fd2d78ecb7c9cf77a4c365eed8b648932c9baf93 (diff) | |
parent | 36523b6830fa468ae9e0335601aed475480b7dd3 (diff) |
Merge remote-tracking branch 'tty/tty-next'
Diffstat (limited to 'Documentation')
4 files changed, 45 insertions, 1 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index c74c0bada494..e1ab91d46799 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -966,6 +966,12 @@ serial port must already be setup and configured. Options are not yet supported. + lantiq,<addr> + Start an early, polled-mode console on a lantiq serial + (lqasc) port at the specified address. The serial port + must already be setup and configured. Options are not + yet supported. + lpuart,<addr> lpuart32,<addr> Use early console provided by Freescale LP UART driver diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index f86bb06c39e9..10276a46ecef 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -19,6 +19,7 @@ Required properties: - "altr,16550-FIFO128" - "fsl,16550-FIFO64" - "fsl,ns16550" + - "ti,da830-uart" - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt index fd970f76a7b8..b542a0ecf06e 100644 --- a/Documentation/devicetree/bindings/serial/serial.txt +++ b/Documentation/devicetree/bindings/serial/serial.txt @@ -23,7 +23,8 @@ Optional properties: they are available for use (wired and enabled by pinmux configuration). This depends on both the UART hardware and the board wiring. Note that this property is mutually-exclusive with "cts-gpios" and - "rts-gpios" above. + "rts-gpios" above, unless support is provided to switch between modes + dynamically. Examples: diff --git a/Documentation/devicetree/bindings/serial/slave-device.txt b/Documentation/devicetree/bindings/serial/slave-device.txt new file mode 100644 index 000000000000..f66037928f5f --- /dev/null +++ b/Documentation/devicetree/bindings/serial/slave-device.txt @@ -0,0 +1,36 @@ +Serial Slave Device DT binding + +This documents the binding structure and common properties for serial +attached devices. Common examples include Bluetooth, WiFi, NFC and GPS +devices. + +Serial attached devices shall be a child node of the host UART device the +slave device is attached to. It is expected that the attached device is +the only child node of the UART device. The slave device node name shall +reflect the generic type of device for the node. + +Required Properties: + +- compatible : A string reflecting the vendor and specific device the node + represents. + +Optional Properties: + +- max-speed : The maximum baud rate the device operates at. This should + only be present if the maximum is less than the slave device + can support. For example, a particular board has some signal + quality issue or the host processor can't support higher + baud rates. + +Example: + +serial@1234 { + compatible = "ns16550a"; + interrupts = <1>; + + bluetooth { + compatible = "brcm,bcm43341-bt"; + interrupt-parent = <&gpio>; + interrupts = <10>; + }; +}; |