Merge remote-tracking branch 'spi/for-next'

3 files changed, 36 insertions, 105 deletions

diff --git a/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt
new file mode 100644
index 000000000000..6069b95a883d
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt
@@ -0,0 +1,29 @@
+Lantiq Synchronous Serial Controller (SSC) SPI master driver
+
+Required properties:
+- compatible: "lantiq,ase-spi", "lantiq,falcon-spi", "lantiq,xrx100-spi"
+- #address-cells: see spi-bus.txt
+- #size-cells: see spi-bus.txt
+- reg: address and length of the spi master registers
+- interrupts: should contain the "spi_rx", "spi_tx" and "spi_err" interrupt.
+
+
+Optional properties:
+- clocks: spi clock phandle
+- num-cs: see spi-bus.txt, set to 8 if unset
+- base-cs: the number of the first chip select, set to 1 if unset.
+
+Example:
+
+
+spi: spi@E100800 {
+	compatible = "lantiq,xrx200-spi", "lantiq,xrx100-spi";
+	reg = <0xE100800 0x100>;
+	interrupt-parent = <&icu0>;
+	interrupts = <22 23 24>;
+	interrupt-names = "spi_rx", "spi_tx", "spi_err";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	num-cs = <6>;
+	base-cs = <1>;
+};
diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt
index d2ca153614f9..83da4931d832 100644
--- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt
+++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt
@@ -31,6 +31,10 @@ Optional Properties:
 - rx-sample-delay-ns: nanoseconds to delay after the SCLK edge before sampling
 		Rx data (may need to be fine tuned for high capacitance lines).
 		No delay (0) by default.
+- pinctrl-names: Names for the pin configuration(s); may be "default" or
+		"sleep", where the "sleep" configuration may describe the state
+		the pins should be in during system suspend. See also
+		pinctrl/pinctrl-bindings.txt.
 
 
 Example:
@@ -46,4 +50,7 @@ Example:
 		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
 		clock-names = "spiclk", "apb_pclk";
+		pinctrl-0 = <&spi1_pins>;
+		pinctrl-1 = <&spi1_sleep>;
+		pinctrl-names = "default", "sleep";
 	};
diff --git a/Documentation/spi/ep93xx_spi b/Documentation/spi/ep93xx_spi
deleted file mode 100644
index 832ddce6e5fb..000000000000
--- a/Documentation/spi/ep93xx_spi
+++ /dev/null
@@ -1,105 +0,0 @@
-Cirrus EP93xx SPI controller driver HOWTO
-=========================================
-
-ep93xx_spi driver brings SPI master support for EP93xx SPI controller.  Chip
-selects are implemented with GPIO lines.
-
-NOTE: If possible, don't use SFRMOUT (SFRM1) signal as a chip select. It will
-not work correctly (it cannot be controlled by software). Use GPIO lines
-instead.
-
-Sample configuration
-====================
-
-Typically driver configuration is done in platform board files (the files under
-arch/arm/mach-ep93xx/*.c). In this example we configure MMC over SPI through
-this driver on TS-7260 board. You can adapt the code to suit your needs.
-
-This example uses EGPIO9 as SD/MMC card chip select (this is wired in DIO1
-header on the board).
-
-You need to select CONFIG_MMC_SPI to use mmc_spi driver.
-
-arch/arm/mach-ep93xx/ts72xx.c:
-
-...
-#include <linux/gpio.h>
-#include <linux/spi/spi.h>
-
-#include <linux/platform_data/spi-ep93xx.h>
-
-/* this is our GPIO line used for chip select */
-#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO9
-
-static int ts72xx_mmc_spi_setup(struct spi_device *spi)
-{
-	int err;
-
-	err = gpio_request(MMC_CHIP_SELECT_GPIO, spi->modalias);
-	if (err)
-		return err;
-
-	gpio_direction_output(MMC_CHIP_SELECT_GPIO, 1);
-
-	return 0;
-}
-
-static void ts72xx_mmc_spi_cleanup(struct spi_device *spi)
-{
-	gpio_set_value(MMC_CHIP_SELECT_GPIO, 1);
-	gpio_direction_input(MMC_CHIP_SELECT_GPIO);
-	gpio_free(MMC_CHIP_SELECT_GPIO);
-}
-
-static void ts72xx_mmc_spi_cs_control(struct spi_device *spi, int value)
-{
-	gpio_set_value(MMC_CHIP_SELECT_GPIO, value);
-}
-
-static struct ep93xx_spi_chip_ops ts72xx_mmc_spi_ops = {
-	.setup		= ts72xx_mmc_spi_setup,
-	.cleanup	= ts72xx_mmc_spi_cleanup,
-	.cs_control	= ts72xx_mmc_spi_cs_control,
-};
-
-static struct spi_board_info ts72xx_spi_devices[] __initdata = {
-	{
-		.modalias		= "mmc_spi",
-		.controller_data	= &ts72xx_mmc_spi_ops,
-		/*
-		 * We use 10 MHz even though the maximum is 7.4 MHz. The driver
-		 * will limit it automatically to max. frequency.
-		 */
-		.max_speed_hz		= 10 * 1000 * 1000,
-		.bus_num		= 0,
-		.chip_select		= 0,
-		.mode			= SPI_MODE_0,
-	},
-};
-
-static struct ep93xx_spi_info ts72xx_spi_info = {
-	.num_chipselect	= ARRAY_SIZE(ts72xx_spi_devices),
-};
-
-static void __init ts72xx_init_machine(void)
-{
-	...
-	ep93xx_register_spi(&ts72xx_spi_info, ts72xx_spi_devices,
-			    ARRAY_SIZE(ts72xx_spi_devices));
-}
-
-The driver can use DMA for the transfers also. In this case ts72xx_spi_info
-becomes:
-
-static struct ep93xx_spi_info ts72xx_spi_info = {
-	.num_chipselect	= ARRAY_SIZE(ts72xx_spi_devices),
-	.use_dma	= true;
-};
-
-Note that CONFIG_EP93XX_DMA should be enabled as well.
-
-Thanks to
-=========
-Martin Guy, H. Hartley Sweeten and others who helped me during development of
-the driver. Simplemachines.it donated me a Sim.One board which I used testing
-the driver on EP9307.