Merge remote-tracking branch 'tty/tty-next'

4 files changed, 45 insertions, 1 deletions

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index f2e745844d5b..63100cd870a9 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -957,6 +957,12 @@
 			serial port must already be setup and configured.
 			Options are not yet supported.
 
+		lantiq,<addr>
+			Start an early, polled-mode console on a lantiq serial
+			(lqasc) port at the specified address. The serial port
+			must already be setup and configured. Options are not
+			yet supported.
+
 		lpuart,<addr>
 		lpuart32,<addr>
 			Use early console provided by Freescale LP UART driver
diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt
index f86bb06c39e9..10276a46ecef 100644
--- a/Documentation/devicetree/bindings/serial/8250.txt
+++ b/Documentation/devicetree/bindings/serial/8250.txt
@@ -19,6 +19,7 @@ Required properties:
 	- "altr,16550-FIFO128"
 	- "fsl,16550-FIFO64"
 	- "fsl,ns16550"
+	- "ti,da830-uart"
 	- "serial" if the port type is unknown.
 - reg : offset and length of the register set for the device.
 - interrupts : should contain uart interrupt.
diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt
index fd970f76a7b8..b542a0ecf06e 100644
--- a/Documentation/devicetree/bindings/serial/serial.txt
+++ b/Documentation/devicetree/bindings/serial/serial.txt
@@ -23,7 +23,8 @@ Optional properties:
     they are available for use (wired and enabled by pinmux configuration).
     This depends on both the UART hardware and the board wiring.
     Note that this property is mutually-exclusive with "cts-gpios" and
-    "rts-gpios" above.
+    "rts-gpios" above, unless support is provided to switch between modes
+    dynamically.
 
 
 Examples:
diff --git a/Documentation/devicetree/bindings/serial/slave-device.txt b/Documentation/devicetree/bindings/serial/slave-device.txt
new file mode 100644
index 000000000000..f66037928f5f
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/slave-device.txt
@@ -0,0 +1,36 @@
+Serial Slave Device DT binding
+
+This documents the binding structure and common properties for serial
+attached devices. Common examples include Bluetooth, WiFi, NFC and GPS
+devices.
+
+Serial attached devices shall be a child node of the host UART device the
+slave device is attached to. It is expected that the attached device is
+the only child node of the UART device. The slave device node name shall
+reflect the generic type of device for the node.
+
+Required Properties:
+
+- compatible 	: A string reflecting the vendor and specific device the node
+		  represents.
+
+Optional Properties:
+
+- max-speed	: The maximum baud rate the device operates at. This should
+		  only be present if the maximum is less than the slave device
+		  can support. For example, a particular board has some signal
+		  quality issue or the host processor can't support higher
+		  baud rates.
+
+Example:
+
+serial@1234 {
+	compatible = "ns16550a";
+	interrupts = <1>;
+
+	bluetooth {
+		compatible = "brcm,bcm43341-bt";
+		interrupt-parent = <&gpio>;
+		interrupts = <10>;
+	};
+};