Age | Commit message (Collapse) | Author |
|
This patch adjusts the minimum voltage for LITTLE core
because the requested minimum voltage is 750mV on the
lowest frequency level.
Change-Id: I335e89d71e45c10f43db7e2e14469c90f03c92b1
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
In Tizen 3.0, keycodes for earjack should be below.
volume down: 114
volume up: 115
media key: 226
Change-Id: Ifc9c5c444980fcdc691daa0066966ba860cb9081
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
|
|
Change-Id: I2a6a9380323f780d327e5e57009ab2edc6aae399
Signed-off-by: Rafal Krypa <r.krypa@samsung.com>
|
|
This patch is to sync rinato defconfig with v4.1.36 rebased tree.
Change-Id: Ia299861792631dcd0dbe3fb0a78cf96ec954593e
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
This patch is to sync trats2 defconfig with v4.1.36 rebased tree.
Change-Id: Ib0a5eaf7fbed9ddeb1e8fed1941f8185b1001c86
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
This patch is to sync odroid defconfig with v4.1.36 rebased tree.
Change-Id: I6de9150678bb53ccf5ba2e319da2744fb472866a
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
This patch is to sync tm2 defconfig with v4.1.36 rebased tree.
Change-Id: I8ceda9fa5747fd5790e5393ede573cc09fd13876
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
Reset line is active in low state, previous configuration was incorrect,
but it worked because logic was also inverted in the driver.
The patch fixes it. To keep bisectability both changes are put into one patch.
The patch adjusts also delays.
Change-Id: I07d08f763fa5ed4805eb638c1d2bb1ddd3328680
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
|
|
These properties are not needed anymore as the driver has been converted
to interrupt properties.
Change-Id: I255287ea913b62c286c1a0c62bdf772d33055c49
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
|
|
Add interrupts property to represent interrupt pin.
Obsolete int-gpio will be removed after driver update to keep bisectability.
Change-Id: I3c766f45cc37a7765f84cabcbee24d5d551dc113
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
|
|
The config allows security marking of network packets.
Iptable need to set packet's secmark to 'System' label to avoid
Smack deny issue only for multicast address range.
* Refer to : https://review.tizen.org/gerrit/#/c/100096/
Change-Id: I28dce71862d2bddba2ede2f72b7cdd493c3d184f
Signed-off-by: jooseong lee <jooseong.lee@samsung.com>
|
|
The config allows security marking of network packets.
Iptable need to set packet's secmark to 'System' label to avoid
Smack deny issue only for multicast address range.
* Refer to : https://review.tizen.org/gerrit/#/c/100096/
Change-Id: If0dcf494197beb7eb5ae035e0998ac2c8907d0cc
Signed-off-by: jooseong lee <jooseong.lee@samsung.com>
|
|
In order to support both USB Serial CAN adaptor and GPS USB interface,
this enables its related options.
Change-Id: I220e8366b51798e38759f18b4d830a3b47302400
Signed-off-by: Sangjung Woo <sangjung.woo@samsung.com>
|
|
In order to support Network tethering, this patch enables its related
options.
Change-Id: I4a358b5df65c539d0b56331040b28711ab096078
Signed-off-by: Sangjung Woo <sangjung.woo@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
|
|
In order to support USB PEAK CAN driver, this patch enables it.
Change-Id: I7d859e657cd22ed753b93e41194b7a1eadf1f8fe
Signed-off-by: Sangjung Woo <sangjung.woo@samsung.com>
|
|
In order to support CAN (i.e. Controller Area Network), this patch
enables CAN and its related options like VCAN.
Change-Id: I4d709b0be98c1ed1c307925fd5cdca0058ea6847
Signed-off-by: Sangjung Woo <sangjung.woo@samsung.com>
|
|
The patch adds gpio for detecting presence of MMC card.
It fixes issue with kernel hang when MMC card is missing
and prevents flooding kernel log with mmc bus parameters.
Change-Id: I6eca44d9942c9f5958dba68a98ea25f2809ed20d
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Origin: https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=fb1aeedb61adcb7651eada9eb79ddfa11f21f085
|
|
Change-Id: I963eaef32f09f32f3e93418e6c236964ee0e54ad
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
This patch enables 6Lowpan modules for BT.
Change-Id: Id607cc9ef9cdcee5600ecfe151562752ade82475
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
This patch enables 6Lowpan modules for BT.
Change-Id: I5181bd4ae1face748049448239cb62e90b341fbf
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
To support cpufreq from non big.little arm socs, CPUFREQ_DT shuold
be enabled. So, this patch enables CPUFREQ_DT config option.
Change-Id: Ic964ce630b6e0eeb4480d5f87b9ec32f375ffc0f
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
This is required to run usb host API test suit.
Change-Id: I203ef286bef030ddd359e6e18145b612a7d8dc05
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
|
|
To support security check of network packet from Tizen platform,
it is required to enable the configs for SMACK_NETFILTER dependent
on NETWORK_SECMARK and AUDIT of NETFILTER.
Change-Id: I684ce5771dbd6e52ee529ede647d36c6561e549e
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
To support security check of network packet from Tizen platform,
it is required to enable the configs for SMACK_NETFILTER dependent
on NETWORK_SECMARK and AUDIT of NETFILTER.
Change-Id: I9176fcad446ea87f503165c4cf2f3aff3c60ec4f
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
The BCM4773 power pins need to be alive during sleep mode,
because the MCU needs to respond to the external sensors events.
Add a sleep alive state for pins.
- gpd2-0 (GPS_HUB_EN)
- gpf2-2 (MCU_AP_INT_2_1.8V)
- gpf2-3 (AP_MCU_INT_1.8V)
While pins:
- gpd8-0 (SHUB_SPI_SCK)
- gpd8-1 (SHUB_SPI_SSN)
- gpd6-0 (SHUB_SPI_MISO)
- gpd6-1 (SHUB_SPI_MOSI)
need to be managed when the device goes and resumes from
sleep mode.
Change-Id: If508f5b4526e5de665f76b0adb96ae64779b6eb7
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
|
|
The CONFIG_SENSORS_SSP_BBD_VER2 flag enables the version 2 of the
sensorhub in the config file.
Change-Id: I21984f496e063f3cb727a8f76f6e189cafc2bd71
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
|
|
Add support for the BCM4773 in the exynos5433 tm2 and tm2e
boards as spi_0 nodes.
Change-Id: I765f87ee868dfe8d4155a42bf895b09c35cbb85b
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
|
|
Add support for the BCM4773 in the exynos5433 tm2 and tm2e
boards as spi_0 nodes.
Move the GPIO initialization pins in the board section.
Change-Id: Ia4567598527d5169c6669c791fcf40e5d7693b70
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
A "extcon" property is added to tm2(e) dts, so sii8620 can be noted about
MHL device connection from MUIC through extcon framework.
Change-Id: I4bd1f7d62cf1d6b1f3252f42267247c9b50b721c
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>
|
|
This patch cleans up non proper line changes.
Change-Id: Ifcbac0c5d194266f88b7e88545a7d86e0bcda96a
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
The wlan and related pinctrl dt nodes are only proper for tm2/tm2e
boards, so it should not be in exynos5433. So this patch moves the
bodes to speicifc board dts files.
Change-Id: Idd0a5bdb34aa4f61ac41c492c9bde2797d26e3af
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
The spi_6 dt node is already disabled from exynos5433, so it is not
really requred to disable from board dts files.
Change-Id: I15e79f79e1cdc3ff6ddaa2f34d63939c5e3fd324
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
Update the tizen_tm2_defcofig file.
Synchronized the defconfig file after updated some Kconfig files.
Change-Id: I9924bfd1ef18130fd36b6120cec0cd6c9dcfc275
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
MALI_DVFS is internal DVFS feature of mali400. Now we use specific
DVFS(USING_GPU_UTILIZATION) and USING_GPU_UTILIZATION conflicts with
MALI_DVFS, so disable MALI_DVFS config.
Change-Id: I7edd335a1f23e09ee38ecb43e9c380f695dac78b
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
|
|
MALI_DVFS is internal DVFS feature of mali400. Now we use specific
DVFS(USING_GPU_UTILIZATION) and USING_GPU_UTILIZATION conflicts with
MALI_DVFS, so disable MALI_DVFS config.
Change-Id: Iebef1cddfecfa968d2b19b8b0af7ba5ae017c841
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
|
|
MALI_DVFS is internal DVFS feature of mali400. Now we use specific
DVFS(USING_GPU_UTILIZATION) and USING_GPU_UTILIZATION conflicts with
MALI_DVFS, so disable MALI_DVFS config.
Change-Id: I00d0b9737a4caed5a357a2e196e0c37392eb1d80
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
|
|
This is required to run usb host API test suit.
Change-Id: I99058db93922e1279f090d76bbacf6c8fe7985b8
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
|
|
This patch enables Android logger driver.
Tizen common platform will use Android logger driver
and dlog will be used as its backend.
Change-Id: Id94c5d8f57bfd9d66c8ace470ff82b58699e20a4
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
Add the reboot-inform property for supporting reboot mode.
Trats2 is INFORM3 register, other boards are using INFORM2 regsiter.
In trats2's case, when we released the tizen-2.X with linux-3.10 kernel,
it had used the INFORM3 register. That's why trats2 only use the INFORM3
register.
Change-Id: Ief314f50c47601ad646789790b36731e64e0b688
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Add the reboot-inform property for supporting reboot mode.
Odroid families use the INFORM2 register as reboot special mode.
Change-Id: I906c32e6d26fcf08748f4916c277fb3995a1117f
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Support the reboot download mode functionality.
It can get from device-treee which INFORM register will be used.
If want to use this functionality, it also needs to implement something
on bootloader side.
Change-Id: Iae42f32d69b84ccdcb39fcfc8bc71f9cc8c42302
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Change-Id: Ic1669e9657da1c601774b3bf366cc6036a77147c
|
|
Disable G2D SYSMMU controllers until support for G2D is really implemented
and G2D SYSMMU register access freeze issue is resolved.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Change-Id: I38542642d255313307d9ac6a836ffece4a402b2b
|
|
This patch replaces mali400 driver from r4p0 to r5p2 for rinato
to align with other boards with mali400.
Change-Id: I3f9cb30ccef2390d1df91e7bb2d9d17b4ce29d6e
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
|
|
This fixes order of reg resources. First has to be resource that has
lowest address because mali400 r5p2 version requires it.
This also adds interrupt-names for g3d nodes. The interrupt-names needs
at mali400 r5p2 version.
Change-Id: I84a31ff3691ffea084b5f3f0abbcf998ea0a8371
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
|
|
This patch updates the defconfig file for rinato to sync with v4.1
tree.
Change-Id: Ib1abd29eb6f1a1c23df44d273de1d1d963370143
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
This patch replaces mali400 driver from r4p0 to r5p2 for trats2
to align with other boards with mali400.
Change-Id: I52d4d85a75d1a399dda3439d5ac6c189b863a48f
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
This patch disables CONFIG_MMC_CLKGATE to remove spamming mmc log
message about setting mmc clock.
Change-Id: I1f3071f3e9da6c5d213e48fcb731595ff7b29679
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
This patch updates the defconfig file for trats2 to sync with v4.1
tree.
Change-Id: Ib9682a36e721a881256ce52caa94a916a91d8403
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
|
|
Currently there is booting issue of tizen 3.0 mobile 32bit platform with
PID1 getting stuck printing "systemd[1]: Time has been changed"
continuously. [1][2]
This problem is related with rtc-s3c and now rtc-s3c is reporting time
values over 2038 years like below:
[ 5.124065] s3c-rtc 10590000.rtc: setting system clock to 2140-10-02 10:52:03 UTC (5388461523)
Android MM N910S kernel uses only pmic rtc, not rtc-s3c so i think it's
better to disable rtc-s3c.
[1] https://github.com/systemd/systemd/issues/1143
[2] https://patchwork.ozlabs.org/patch/585661
Change-Id: Idc580c2494aa309607dd835ca39411236f3366e6
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
|