| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fairly small fixes. None is a real show stopper, two automation
detected problems: one memory leak, one use after free and four others
each of which fixes something that has been a significant source of
annoyance to someone"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send
scsi: aacraid: Fix INTx/MSI-x issue with older controllers
scsi: mpt3sas: disable ASPM for MPI2 controllers
scsi: mpt3sas: Force request partial completion alignment
scsi: qla2xxx: Avoid that issuing a LIP triggers a kernel crash
scsi: qla2xxx: Fix a recently introduced memory leak
|
|
Pull networking fixes from David Miller:
1) If the timing is wrong we can indefinitely stop generating new ipv6
temporary addresses, from Marcus Huewe.
2) Don't double free per-cpu stats in ipv6 SIT tunnel driver, from Cong
Wang.
3) Put protections in place so that AF_PACKET is not able to submit
packets which don't even have a link level header to drivers. From
Willem de Bruijn.
4) Fix memory leaks in ipv4 and ipv6 multicast code, from Hangbin Liu.
5) Don't use udp_ioctl() in l2tp code, UDP version expects a UDP socket
and that doesn't go over very well when it is passed an L2TP one.
Fix from Eric Dumazet.
6) Don't crash on NULL pointer in phy_attach_direct(), from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
l2tp: do not use udp_ioctl()
xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
NET: mkiss: Fix panic
net: hns: Fix the device being used for dma mapping during TX
net: phy: Initialize mdio clock at probe function
igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
xen-netfront: Improve error handling during initialization
sierra_net: Skip validating irrelevant fields for IDLE LSIs
sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
kcm: fix 0-length case for kcm_sendmsg()
xen-netfront: Rework the fix for Rx stall during OOM and network stress
net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
net: thunderx: Fix PHY autoneg for SGMII QLM mode
net: dsa: Do not destroy invalid network devices
ping: fix a null pointer dereference
packet: round up linear to header len
net: introduce device min_header_len
sit: fix a double free on error path
lwtunnel: valid encap attr check should return 0 when lwtunnel is disabled
ipv6: addrconf: fix generation of new temporary addresses
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Third round of -rc fixes for 4.10 kernel:
- two security related issues in the rxe driver
- one compile issue in the RDMA uapi header"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA: Don't reference kernel private header from UAPI header
IB/rxe: Fix mem_check_range integer overflow
IB/rxe: Fix resid update
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"Two bugfixes (proper IO mapping and use of mutex) for a driver feature
we introduced in this cycle"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: piix4: Request the SMBUS semaphore inside the mutex
i2c: piix4: Fix request_region size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC host fix from Ulf Hansson:
"mmci: Fix hang while waiting for busy-end interrupt"
* tag 'mmc-v4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mmci: avoid clearing ST Micro busy end interrupt mistakenly
|
|
rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a USB-to-serial adapter is unplugged, the driver re-initializes, with
dev->hard_header_len and dev->addr_len set to zero, instead of the correct
values. If then a packet is sent through the half-dead interface, the
kernel will panic due to running out of headroom in the skb when pushing
for the AX.25 headers resulting in this panic:
[<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50)
[<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25])
[<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss])
[<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8)
[<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914)
[<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0)
[<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48)
This patch makes mkiss behave like the 6pack driver. 6pack does not
panic. In 6pack.c sp_setup() (same function name here) the values for
dev->hard_header_len and dev->addr_len are set to the same values as in
my mkiss patch.
[ralf@linux-mips.org: Massages original submission to conform to the usual
standards for patch submissions.]
Signed-off-by: Thomas Osterried <thomas@osterried.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This should be the final set of drm fixes for 4.10: one vmwgfx boot
fix, one vc4 fix, and a few i915 fixes:
* tag 'drm-fixes-for-v4.10-rc8' of git://people.freedesktop.org/~airlied/linux:
drm: vc4: adapt to new behaviour of drm_crtc.c
drm/i915: Always convert incoming exec offsets to non-canonical
drm/i915: Remove overzealous fence warn on runtime suspend
drm/i915/bxt: Add MST support when do DPLL calculation
drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
drm/i915: fix i915 running as dom0 under Xen
drm/i915: Flush untouched framebuffers before display on !llc
drm/i915: fix use-after-free in page_flip_completed()
drm/vmwgfx: Fix depth input into drm_mode_legacy_fb_format
|
|
Dan Carpenter kindly reported:
<quote>
The patch d27a7cb91960: "zfcp: trace on request for open and close of
WKA port" from Aug 10, 2016, leads to the following static checker
warning:
drivers/s390/scsi/zfcp_fsf.c:1615 zfcp_fsf_open_wka_port()
warn: 'req' was already freed.
drivers/s390/scsi/zfcp_fsf.c
1609 zfcp_fsf_start_timer(req, ZFCP_FSF_REQUEST_TIMEOUT);
1610 retval = zfcp_fsf_req_send(req);
1611 if (retval)
1612 zfcp_fsf_req_free(req);
^^^
Freed.
1613 out:
1614 spin_unlock_irq(&qdio->req_q_lock);
1615 if (req && !IS_ERR(req))
1616 zfcp_dbf_rec_run_wka("fsowp_1", wka_port, req->req_id);
^^^^^^^^^^^
Use after free.
1617 return retval;
1618 }
Same thing for zfcp_fsf_close_wka_port() as well.
</quote>
Rather than relying on req being NULL (or ERR_PTR) for all cases where
we don't want to trace or should not trace,
simply check retval which is unconditionally initialized with -EIO != 0
and it can only become 0 on successful retval = zfcp_fsf_req_send(req).
With that we can also remove the then again unnecessary unconditional
initialization of req which was introduced with that earlier commit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
commit 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang")
caused a problem on older controllers which do not support MSI-x (namely
ASR3405,ASR3805). This patch conditionalizes the previous patch to
controllers which support MSI-x
Cc: <stable@vger.kernel.org> # v4.7+
Fixes: 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang")
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-fixes
Hopefully final fixes for v4.10, about half of them stable material.
* tag 'drm-intel-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Always convert incoming exec offsets to non-canonical
drm/i915: Remove overzealous fence warn on runtime suspend
drm/i915/bxt: Add MST support when do DPLL calculation
drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
drm/i915: fix i915 running as dom0 under Xen
drm/i915: Flush untouched framebuffers before display on !llc
drm/i915: fix use-after-free in page_flip_completed()
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Last-minute vc4 fix for 4.10.
* tag 'drm-misc-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-misc:
drm: vc4: adapt to new behaviour of drm_crtc.c
|
|
MPI2 controllers sometimes got lost (i.e. disappear from
/sys/bus/pci/devices) if ASMP is enabled.
Signed-off-by: Slava Kardakov <ojab@ojab.ru>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=60644
Cc: <stable@vger.kernel.org>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a crash when running out of grant refs when creating many
queues across many netdevs.
* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the context is deactivated, the link_type is set to 0xff, which
triggers a warning message, and results in a wrong link status, as
the LSI is ignored.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a context is configured as dualstack ("IPv4v6"), the modem indicates
the context activation with a slightly different indication message.
The dual-stack indication omits the link_type (IPv4/v6) and adds
additional address fields.
IPv6 LSIs are identical to IPv4 LSIs, but have a different link type.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 90c311b0eeea ("xen-netfront: Fix Rx stall during network
stress and OOM") caused the refill timer to be triggerred almost on
all invocations of xennet_alloc_rx_buffers for certain workloads.
This reworks the fix by reverting to the old behaviour and taking into
consideration the skb allocation failure. Refill timer is now triggered
on insufficient requests or skb allocation failure.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Fixes: 90c311b0eeea (xen-netfront: Fix Rx stall during network stress and OOM)
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"This target series for v4.10 contains fixes which address a few
long-standing bugs that DATERA's QA + automation teams have uncovered
while putting v4.1.y target code into production usage.
We've been running the top three in our nightly automated regression
runs for the last two months, and the COMPARE_AND_WRITE fix Mr. Gary
Guo has been manually verifying against a four node ESX cluster this
past week.
Note all of them have CC' stable tags.
Summary:
- Fix a bug with ESX EXTENDED_COPY + SAM_STAT_RESERVATION_CONFLICT
status, where target_core_xcopy.c logic was incorrectly returning
SAM_STAT_CHECK_CONDITION for all non SAM_STAT_GOOD cases (Nixon
Vincent)
- Fix a TMR LUN_RESET hung task bug while other in-flight TMRs are
being aborted, before the new one had been dispatched into tmr_wq
(Rob Millner)
- Fix a long standing double free OOPs, where a dynamically generated
'demo-mode' NodeACL has multiple sessions associated with it, and
the /sys/kernel/config/target/$FABRIC/$WWN/ subsequently disables
demo-mode, but never converts the dynamic ACL into a explicit ACL
(Rob Millner)
- Fix a long standing reference leak with ESX VAAI COMPARE_AND_WRITE
when the second phase WRITE COMMIT command fails, resulting in
CHECK_CONDITION response never being sent and se_cmd->cmd_kref
never reaching zero (Gary Guo)
Beyond these items on v4.1.y we've reproduced, fixed, and run through
our regression test suite using iscsi-target exports, there are two
additional outstanding list items:
- Remove a >= v4.2 RCU conversion BUG_ON that would trigger when
dynamic node NodeACLs where being converted to explicit NodeACLs.
The patch drops the BUG_ON to follow how pre RCU conversion worked
for this special case (Benjamin Estrabaud)
- Add ibmvscsis target_core_fabric_ops->max_data_sg_nent assignment
to match what IBM's Virtual SCSI hypervisor is already enforcing at
transport layer. (Bryant Ly + Steven Royer)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
ibmvscsis: Add SGL limit
target: Fix COMPARE_AND_WRITE ref leak for non GOOD status
target: Fix multi-session dynamic se_node_acl double free OOPs
target: Fix early transport_generic_handle_tmr abort scenario
target: Use correct SCSI status during EXTENDED_COPY exception
target: Don't BUG_ON during NodeACL dynamic -> explicit conversion
|
|
The Generic PHY drivers gets assigned after we checked that the current
PHY driver is NULL, so we need to check a few things before we can
safely dereference d->driver. This would be causing a NULL deference to
occur when a system binds to the Generic PHY driver. Update
phy_attach_direct() to do the following:
- grab the driver module reference after we have assigned the Generic
PHY drivers accordingly, and remember we came from the generic PHY
path
- update the error path to clean up the module reference in case the
Generic PHY probe function fails
- split the error path involving phy_detacht() to avoid double free/put
since phy_detach() does all the clean up
- finally, have phy_detach() drop the module reference count before we
call device_release_driver() for the Generic PHY driver case
Fixes: cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix for a crash in uinput, and a fix for build errors when HID-RMI
is built-in but SERIO is a module"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - select 'SERIO' when needed
Input: uinput - fix crash when mixing old and new init style
|
|
Pull VFIO fix from Alex Williamson:
"Fix regression in attaching groups to existing container for SPAPR
IOMMU backend (Alexey Kardashevskiy)"
* tag 'vfio-v4.10-final' of git://github.com/awilliam/linux-vfio:
vfio/spapr_tce: Set window when adding additional groups to container
|
|
SMBSLVCNT must be protected with the piix4_mutex_sb800 in order to avoid
multiple buses accessing to the semaphore at the same time.
Fixes: 701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Since '701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")' we
are using the SMBSLVCNT register at offset 0x8. We need to request it.
Fixes: 701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This reverts commit 2cc751545854d7bd7eedf4d7e377bb52e176cd07.
With this commit in place I get on a Cavium ThunderX (arm64) system:
$ if=/dev/hwrng bs=256 count=1 | od -t x1 -A x -v > rng-bad.txt
1+0 records in
1+0 records out
256 bytes (256 B) copied, 9.1171e-05 s, 2.8 MB/s
$ dd if=/dev/hwrng bs=256 count=1 | od -t x1 -A x -v >> rng-bad.txt
1+0 records in
1+0 records out
256 bytes (256 B) copied, 9.6141e-05 s, 2.7 MB/s
$ cat rng-bad.txt
000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000040 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000050 00 00 00 00 37 20 46 ae d0 fc 1c 55 25 6e b0 b8
000060 7c 7e d7 d4 00 0f 6f b2 91 1e 30 a8 fa 3e 52 0e
000070 06 2d 53 30 be a1 20 0f aa 56 6e 0e 44 6e f4 35
000080 b7 6a fe d2 52 70 7e 58 56 02 41 ea d1 9c 6a 6a
000090 d1 bd d8 4c da 35 45 ef 89 55 fc 59 d5 cd 57 ba
0000a0 4e 3e 02 1c 12 76 43 37 23 e1 9f 7a 9f 9e 99 24
0000b0 47 b2 de e3 79 85 f6 55 7e ad 76 13 4f a0 b5 41
0000c0 c6 92 42 01 d9 12 de 8f b4 7b 6e ae d7 24 fc 65
0000d0 4d af 0a aa 36 d9 17 8d 0e 8b 7a 3b b6 5f 96 47
0000e0 46 f7 d8 ce 0b e8 3e c6 13 a6 2c b6 d6 cc 17 26
0000f0 e3 c3 17 8e 9e 45 56 1e 41 ef 29 1a a8 65 c8 3a
000100
000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000040 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000050 00 00 00 00 f4 90 65 aa 8b f2 5e 31 01 53 b4 d4
000060 06 c0 23 a2 99 3d 01 e4 b0 c1 b1 55 0f 80 63 cf
000070 33 24 d8 3a 1d 5e cd 2c ba c0 d0 18 6f bc 97 46
000080 1e 19 51 b1 90 15 af 80 5e d1 08 0d eb b0 6c ab
000090 6a b4 fe 62 37 c5 e1 ee 93 c3 58 78 91 2a d5 23
0000a0 63 50 eb 1f 3b 84 35 18 cf b2 a4 b8 46 69 9e cf
0000b0 0c 95 af 03 51 45 a8 42 f1 64 c9 55 fc 69 76 63
0000c0 98 9d 82 fa 76 85 24 da 80 07 29 fe 4e 76 0c 61
0000d0 ff 23 94 4f c8 5c ce 0b 50 e8 31 bc 9d ce f4 ca
0000e0 be ca 28 da e6 fa cc 64 1c ec a8 41 db fe 42 bd
0000f0 a0 e2 4b 32 b4 52 ba 03 70 8e c1 8e d0 50 3a c6
000100
To my untrained mental entropy detector, the first several bytes of
each read from /dev/hwrng seem to not be very random (i.e. all zero).
When I revert the patch (apply this patch), I get back to what we have
in v4.9, which looks like (much more random appearing):
$ dd if=/dev/hwrng bs=256 count=1 | od -t x1 -A x -v > rng-good.txt
1+0 records in
1+0 records out
256 bytes (256 B) copied, 0.000252233 s, 1.0 MB/s
$ dd if=/dev/hwrng bs=256 count=1 | od -t x1 -A x -v >> rng-good.txt
1+0 records in
1+0 records out
256 bytes (256 B) copied, 0.000113571 s, 2.3 MB/s
$ cat rng-good.txt
000000 75 d1 2d 19 68 1f d2 26 a1 49 22 61 66 e8 09 e5
000010 e0 4e 10 d0 1a 2c 45 5d 59 04 79 8e e2 b7 2c 2e
000020 e8 ad da 34 d5 56 51 3d 58 29 c7 7a 8e ed 22 67
000030 f9 25 b9 fb c6 b7 9c 35 1f 84 21 35 c1 1d 48 34
000040 45 7c f6 f1 57 63 1a 88 38 e8 81 f0 a9 63 ad 0e
000050 be 5d 3e 74 2e 4e cb 36 c2 01 a8 14 e1 38 e1 bb
000060 23 79 09 56 77 19 ff 98 e8 44 f3 27 eb 6e 0a cb
000070 c9 36 e3 2a 96 13 07 a0 90 3f 3b bd 1d 04 1d 67
000080 be 33 14 f8 02 c2 a4 02 ab 8b 5b 74 86 17 f0 5e
000090 a1 d7 aa ef a6 21 7b 93 d1 85 86 eb 4e 8c d0 4c
0000a0 56 ac e4 45 27 44 84 9f 71 db 36 b9 f7 47 d7 b3
0000b0 f2 9c 62 41 a3 46 2b 5b e3 80 63 a4 35 b5 3c f4
0000c0 bc 1e 3a ad e4 59 4a 98 6c e8 8d ff 1b 16 f8 52
0000d0 05 5c 2f 52 2a 0f 45 5b 51 fb 93 97 a4 49 4f 06
0000e0 f3 a0 d1 1e ba 3d ed a7 60 8f bb 84 2c 21 94 2d
0000f0 b3 66 a6 61 1e 58 30 24 85 f8 c8 18 c3 77 00 22
000100
000000 73 ca cc a1 d9 bb 21 8d c3 5c f3 ab 43 6d a7 a4
000010 4a fd c5 f4 9c ba 4a 0f b1 2e 19 15 4e 84 26 e0
000020 67 c9 f2 52 4d 65 1f 81 b7 8b 6d 2b 56 7b 99 75
000030 2e cd d0 db 08 0c 4b df f3 83 c6 83 00 2e 2b b8
000040 0f af 61 1d f2 02 35 74 b5 a4 6f 28 f3 a1 09 12
000050 f2 53 b5 d2 da 45 01 e5 12 d6 46 f8 0b db ed 51
000060 7b f4 0d 54 e0 63 ea 22 e2 1d d0 d6 d0 e7 7e e0
000070 93 91 fb 87 95 43 41 28 de 3d 8b a3 a8 8f c4 9e
000080 30 95 12 7a b2 27 28 ff 37 04 2e 09 7c dd 7c 12
000090 e1 50 60 fb 6d 5f a8 65 14 40 89 e3 4c d2 87 8f
0000a0 34 76 7e 66 7a 8e 6b a3 fc cf 38 52 2e f9 26 f0
0000b0 98 63 15 06 34 99 b2 88 4f aa d8 14 88 71 f1 81
0000c0 be 51 11 2b f4 7e a0 1e 12 b2 44 2e f6 8d 84 ea
0000d0 63 82 2b 66 b3 9a fd 08 73 5a c2 cc ab 5a af b1
0000e0 88 e3 a6 80 4b fc db ed 71 e0 ae c0 0a a4 8c 35
0000f0 eb 89 f9 8a 4b 52 59 6f 09 7c 01 3f 56 e7 c7 bf
000100
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge fixes from Andrew Morton:
"4 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/slub.c: fix random_seq offset destruction
cpumask: use nr_cpumask_bits for parsing functions
mm: avoid returning VM_FAULT_RETRY from ->page_mkwrite handlers
kernel/ucount.c: mark user_header with kmemleak_ignore()
|
|
Some ->page_mkwrite handlers may return VM_FAULT_RETRY as its return
code (GFS2 or Lustre can definitely do this). However VM_FAULT_RETRY
from ->page_mkwrite is completely unhandled by the mm code and results
in locking and writeably mapping the page which definitely is not what
the caller wanted.
Fix Lustre and block_page_mkwrite_ret() used by other filesystems
(notably GFS2) to return VM_FAULT_NOPAGE instead which results in
bailing out from the fault code, the CPU then retries the access, and we
fault again effectively doing what the handler wanted.
Link: http://lkml.kernel.org/r/20170203150729.15863-1-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When drm_crtc_init_with_planes() was orignally added
(in drm_crtc.c, e13161af80c185ecd8dc4641d0f5df58f9e3e0af
drm: Add drm_crtc_init_with_planes() (v2)), it only checked for "primary"
being non-null. If that was the case, it modified primary->possible_crtcs.
Then, when support for cursor planes was added
(fc1d3e44ef7c1db93384150fdbf8948dcf949f15 drm: Allow drivers to register
cursor planes with crtc), the same behaviour was implemented for cursor
planes.
vc4_plane_init() since its inception has passed 0xff as "possible_crtcs"
parameter to drm_universal_plane_init(). With a change in drm_crtc.c
(7abc7d47510c75dd984380ebf819616e574c9604 drm: don't override
possible_crtcs for primary/cursor planes) passing 0xff results in primary's
possible_crtcs set to 0xff (cursor was updated manually by vc4_crtc.c).
Consequently, it would be allowed to use the primary plane from CRTC 1 (for
example) on CRTC 0, which would result in the overlay and cursors being
buried.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/1485941708-27892-1-git-send-email-andrzej.p@samsung.com
Fixes: 7abc7d47510c ("drm: don't override possible_crtcs for primary/cursor planes")
|
|
This patch fixes the case where there is no phydev attached
to a LMAC in DT due to non-existance of a PHY driver or due
to usage of non-stanadard PHY which doesn't support autoneg.
Changes dependeds on firmware to send correct info w.r.t
PHY and autoneg capability.
This patch also covers a case where a 10G/40G interface is used
as a 1G with convertors with Cortina PHY in between.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- check MSI affinity vs. number of vectors to avoid memory corruption
- drop runtime power management for PCIe hotplug ports for now to avoid
regressing hotplug via sysfs
* tag 'pci-v4.10-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: pciehp: Add runtime PM support for PCIe hotplug ports"
PCI/MSI: Don't apply affinity if there aren't enough vectors left
|
|
The stack must not pass packets to device drivers that are shorter
than the minimum link layer header length.
Previously, packet sockets would drop packets smaller than or equal
to dev->hard_header_len, but this has false positives. Zero length
payload is used over Ethernet. Other link layer protocols support
variable length headers. Support for validation of these protocols
removed the min length check for all protocols.
Introduce an explicit dev->min_header_len parameter and drop all
packets below this value. Initially, set it to non-zero only for
Ethernet and loopback. Other protocols can follow in a patch to
net-next.
Fixes: 9ed988cd5915 ("packet: validate variable length ll headers")
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds internal LIO sgl limit since the driver already
sets a max transfer limit on transport layer of 1MB to the client.
Cc: stable@vger.kernel.org
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Update the range check to avoid integer-overflow in edge case.
Resolves CVE 2016-8636.
Signed-off-by: Eyal Itkin <eyal.itkin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Update the response's resid field when larger than MTU, instead of only
updating the local resid variable.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Eyal Itkin <eyal.itkin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch addresses a long standing bug where the commit phase
of COMPARE_AND_WRITE would result in a se_cmd->cmd_kref reference
leak if se_cmd->scsi_status returned non SAM_STAT_GOOD.
This would manifest first as a lost SCSI response, and eventual
hung task during fabric driver logout or re-login, as existing
shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref
to reach zero.
To address this bug, compare_and_write_post() has been changed
to drop the incorrect !cmd->scsi_status conditional that was
preventing *post_ret = 1 for being set during non SAM_STAT_GOOD
status.
This patch has been tested with SAM_STAT_CHECK_CONDITION status
from normal target_complete_cmd() callback path, as well as the
incoming __target_execute_cmd() submission failure path when
se_cmd->execute_cmd() returns non zero status.
Reported-by: Donald White <dew@datera.io>
Cc: Donald White <dew@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Gary Guo <ghg@datera.io>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a long-standing bug with multi-session
(eg: iscsi-target + iser-target) se_node_acl dynamic free
withini transport_deregister_session().
This bug is caused when a storage endpoint is configured with
demo-mode (generate_node_acls = 1 + cache_dynamic_acls = 1)
initiators, and initiator login creates a new dynamic node acl
and attaches two sessions to it.
After that, demo-mode for the storage instance is disabled via
configfs (generate_node_acls = 0 + cache_dynamic_acls = 0) and
the existing dynamic acl is never converted to an explicit ACL.
The end result is dynamic acl resources are released twice when
the sessions are shutdown in transport_deregister_session().
If the storage instance is not changed to disable demo-mode,
or the dynamic acl is converted to an explict ACL, or there
is only a single session associated with the dynamic ACL,
the bug is not triggered.
To address this big, move the release of dynamic se_node_acl
memory into target_complete_nacl() so it's only freed once
when se_node_acl->acl_kref reaches zero.
(Drop unnecessary list_del_init usage - HCH)
Reported-by: Rob Millner <rlm@daterainc.com>
Tested-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug where incoming task management requests
can be explicitly aborted during an active LUN_RESET, but who's
struct work_struct are canceled in-flight before execution.
This occurs when core_tmr_drain_tmr_list() invokes cancel_work_sync()
for the incoming se_tmr_req->task_cmd->work, resulting in cmd->work
for target_tmr_work() never getting invoked and the aborted TMR
waiting indefinately within transport_wait_for_tasks().
To address this case, perform a CMD_T_ABORTED check early in
transport_generic_handle_tmr(), and invoke the normal path via
transport_cmd_check_stop_to_fabric() to complete any TMR kthreads
blocked waiting for CMD_T_STOP in transport_wait_for_tasks().
Also, move the TRANSPORT_ISTATE_PROCESSING assignment earlier
into transport_generic_handle_tmr() so the existing check in
core_tmr_drain_tmr_list() avoids attempting abort the incoming
se_tmr_req->task_cmd->work if it has already been queued into
se_device->tmr_wq.
Reported-by: Rob Millner <rlm@daterainc.com>
Tested-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds the missing target_complete_cmd() SCSI status
parameter change in target_xcopy_do_work(), that was originally
missing in commit 926317de33.
It correctly propigates up the correct SCSI status during
EXTENDED_COPY exception cases, instead of always using the
hardcoded SAM_STAT_CHECK_CONDITION from original code.
This is required for ESX host environments that expect to
hit SAM_STAT_RESERVATION_CONFLICT for certain scenarios,
and SAM_STAT_CHECK_CONDITION results in non-retriable
status for these cases.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
After the v4.2+ RCU conversion to se_node_acl->lun_entry_hlist,
a BUG_ON() was added in core_enable_device_list_for_node() to
detect when the located orig->se_lun_acl contains an existing
se_lun_acl pointer reference.
However, this scenario can happen when a dynamically generated
NodeACL is being converted to an explicit NodeACL, when the
explicit NodeACL contains a different LUN mapping than the
default provided by the WWN endpoint.
So instead of triggering BUG_ON(), go ahead and fail instead
following the original pre RCU conversion logic.
Reported-by: Benjamin ESTRABAUD <ben.estrabaud@mpstor.com>
Cc: Benjamin ESTRABAUD <ben.estrabaud@mpstor.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We're using non-canonical addresses in drm_mm, and we're making sure that
userspace is using canonical addressing - both in case of softpin
(verifying incoming offset) and when relocating (converting to canonical
when updating offset returned to userspace).
Unfortunately when considering the need for relocations, we're comparing
offset from userspace (in canonical form) with drm_mm node (in
non-canonical form), and as a result, we end up always relocating if our
offsets are in the "problematic" range.
Let's always convert the offsets to avoid the performance impact of
relocations.
Fixes: a5f0edf63bdf ("drm/i915: Avoid writing relocs with addresses in non-canonical form")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Reported-by: Michał Pyrzowski <michal.pyrzowski@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207195559.18798-1-michal.winiarski@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 038c95a313e4ca954ee5ab8a0c7559a646b0f462)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The goal of the WARN was to catch when we are still actively using the
fence as we go into the runtime suspend. However, the reg->pin_count is
too coarse as it does not distinguish between exclusive ownership of the
fence register from activity.
I've not improved on the WARN, nor have we captured this WARN in an
exact igt, but it is showing up regularly in the wild:
[ 1915.935332] WARNING: CPU: 1 PID: 10861 at drivers/gpu/drm/i915/i915_gem.c:2022 i915_gem_runtime_suspend+0x116/0x130 [i915]
[ 1915.935383] WARN_ON(reg->pin_count)[ 1915.935399] Modules linked in:
snd_hda_intel i915 drm_kms_helper vgem netconsole scsi_transport_iscsi fuse vfat fat x86_pkg_temp_thermal coretemp intel_cstate intel_uncore snd_hda_codec_hdmi snd_hda_codec_generic snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd mei_me mei serio_raw intel_rapl_perf intel_pch_thermal soundcore wmi acpi_pad i2c_algo_bit syscopyarea sysfillrect sysimgblt fb_sys_fops drm r8169 mii video [last unloaded: drm_kms_helper]
[ 1915.935785] CPU: 1 PID: 10861 Comm: kworker/1:0 Tainted: G U W 4.9.0-rc5+ #170
[ 1915.935799] Hardware name: LENOVO 80MX/Lenovo E31-80, BIOS DCCN34WW(V2.03) 12/01/2015
[ 1915.935822] Workqueue: pm pm_runtime_work
[ 1915.935845] ffffc900044fbbf0 ffffffffac3220bc ffffc900044fbc40 0000000000000000
[ 1915.935890] ffffc900044fbc30 ffffffffac059bcb 000007e6044fbc60 ffff8801626e3198
[ 1915.935937] ffff8801626e0000 0000000000000002 ffffffffc05e5d4e 0000000000000000
[ 1915.935985] Call Trace:
[ 1915.936013] [<ffffffffac3220bc>] dump_stack+0x4f/0x73
[ 1915.936038] [<ffffffffac059bcb>] __warn+0xcb/0xf0
[ 1915.936060] [<ffffffffac059c4f>] warn_slowpath_fmt+0x5f/0x80
[ 1915.936158] [<ffffffffc052d916>] i915_gem_runtime_suspend+0x116/0x130 [i915]
[ 1915.936251] [<ffffffffc04f1c74>] intel_runtime_suspend+0x64/0x280 [i915]
[ 1915.936277] [<ffffffffac0926f1>] ? dequeue_entity+0x241/0xbc0
[ 1915.936298] [<ffffffffac36bb85>] pci_pm_runtime_suspend+0x55/0x180
[ 1915.936317] [<ffffffffac36bb30>] ? pci_pm_runtime_resume+0xa0/0xa0
[ 1915.936339] [<ffffffffac4514e2>] __rpm_callback+0x32/0x70
[ 1915.936356] [<ffffffffac451544>] rpm_callback+0x24/0x80
[ 1915.936375] [<ffffffffac36bb30>] ? pci_pm_runtime_resume+0xa0/0xa0
[ 1915.936392] [<ffffffffac45222d>] rpm_suspend+0x12d/0x680
[ 1915.936415] [<ffffffffac69f6d7>] ? _raw_spin_unlock_irq+0x17/0x30
[ 1915.936435] [<ffffffffac0810b8>] ? finish_task_switch+0x88/0x220
[ 1915.936455] [<ffffffffac4534bf>] pm_runtime_work+0x6f/0xb0
[ 1915.936477] [<ffffffffac074353>] process_one_work+0x1f3/0x4d0
[ 1915.936501] [<ffffffffac074678>] worker_thread+0x48/0x4e0
[ 1915.936523] [<ffffffffac074630>] ? process_one_work+0x4d0/0x4d0
[ 1915.936542] [<ffffffffac074630>] ? process_one_work+0x4d0/0x4d0
[ 1915.936559] [<ffffffffac07a2c9>] kthread+0xd9/0xf0
[ 1915.936580] [<ffffffffac07a1f0>] ? kthread_park+0x60/0x60
[ 1915.936600] [<ffffffffac69fe62>] ret_from_fork+0x22/0x30
In the case the register is pinned, it should be present and we will
need to invalidate them to be restored upon resume as we cannot expect
the owner of the pin to call get_fence prior to use after resume.
Fixes: 7c108fd8feac ("drm/i915: Move fence cancellation to runtime suspend")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98804
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Imre Deak <imre.deak@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170203125717.8431-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit e0ec3ec698851a6c97a12d696407b3ff77700c23)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add the missing INTEL_OUTPUT_DP_MST case in bxt_get_dpll()
to correctly initialize the crtc_state and port plls when
link training a DP MST monitor on BXT/APL devices.
Fixes: a277ca7dc01d ("drm/i915: Split bxt_ddi_pll_select()")
Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=99572
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Gary C Wang <gary.c.wang@intel.com>
Reviewed-by: Ciobanu, Nathan D <nathan.d.ciobanu@intel.com>
Reviewed-by: Herbert, Marc <marc.herbert@intel.com>
Reviewed-by: Bride, Jim <jim.bride@intel.com>
Reviewed-by: Navare, Manasi D <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486096329-6255-1-git-send-email-shawn.c.lee@intel.com
(cherry picked from commit 0aab2c721d81590012a5021a516f00666646741f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This fixes a race condition that may occur whenever ST micro busy end
interrupt is raised just after being unmasked but before leaving mmci
interrupt context.
A dead-lock has been found if connecting mmci ST Micro variant whose amba
id is 0x10480180 to some new eMMC that supports internal caches. Whenever
mmci driver enables cache control by programming eMMC's EXT_CSD register,
block driver may request to flush the eMMC internal caches causing mmci
driver to send a MMC_SWITCH command to the card with FLUSH_CACHE operation.
And because busy end interrupt may be mistakenly cleared while not yet
processed, this mmc request may never complete. As a result, mmcqd task
may be stuck forever.
Here is an instance caught by lockup detector which shows that mmcqd task
was hung while waiting for mmc_flush_cache command to complete:
..
[ 240.251595] INFO: task mmcqd/1:52 blocked for more than 120 seconds.
[ 240.257973] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.263109] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.270955] mmcqd/1 D c047504c 0 52 2 0x00000000
[ 240.277359] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.284418] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.292191] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.300491] [<c0476040>] (wait_for_common) from [<c02efc1c>] (mmc_wait_for_req_done+0x4c/0x13c)
[ 240.309224] [<c02efc1c>] (mmc_wait_for_req_done) from [<c02efd90>] (mmc_wait_for_cmd+0x64/0x84)
[ 240.317953] [<c02efd90>] (mmc_wait_for_cmd) from [<c02f5b14>] (__mmc_switch+0xa4/0x2a8)
[ 240.325964] [<c02f5b14>] (__mmc_switch) from [<c02f5d40>] (mmc_switch+0x28/0x30)
[ 240.333389] [<c02f5d40>] (mmc_switch) from [<c02f0984>] (mmc_flush_cache+0x54/0x80)
[ 240.341073] [<c02f0984>] (mmc_flush_cache) from [<c02ff0c4>] (mmc_blk_issue_rq+0x114/0x4e8)
[ 240.349459] [<c02ff0c4>] (mmc_blk_issue_rq) from [<c03008d4>] (mmc_queue_thread+0xc0/0x180)
[ 240.357844] [<c03008d4>] (mmc_queue_thread) from [<c003cf90>] (kthread+0xdc/0xf4)
[ 240.365339] [<c003cf90>] (kthread) from [<c0010068>] (ret_from_fork+0x14/0x2c)
..
..
[ 240.664311] INFO: task partprobe:564 blocked for more than 120 seconds.
[ 240.670943] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.676078] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.683922] partprobe D c047504c 0 564 486 0x00000000
[ 240.690318] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.697396] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.705149] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.713446] [<c0476040>] (wait_for_common) from [<c01f3300>] (submit_bio_wait+0x58/0x64)
[ 240.721571] [<c01f3300>] (submit_bio_wait) from [<c01fbbd8>] (blkdev_issue_flush+0x60/0x88)
[ 240.729957] [<c01fbbd8>] (blkdev_issue_flush) from [<c010ff84>] (blkdev_fsync+0x34/0x44)
[ 240.738083] [<c010ff84>] (blkdev_fsync) from [<c0109594>] (do_fsync+0x3c/0x64)
[ 240.745319] [<c0109594>] (do_fsync) from [<c000ffc0>] (ret_fast_syscall+0x0/0x3c)
..
Here is the detailed sequence showing when this issue may happen:
1) At probe time, mmci device is initialized and card busy detection based
on DAT[0] monitoring is enabled.
2) Later during run time, since card reported to support internal caches, a
MMCI_SWITCH command is sent to eMMC device with FLUSH_CACHE operation. On
receiving this command, eMMC may enter busy state (for a relatively short
time in the case of the dead-lock).
3) Then mmci interrupt is raised and mmci_irq() is called:
MMCISTATUS register is read and is equal to 0x01000440. So the following
status bits are set:
- MCI_CMDRESPEND (= 6)
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is 0x3FF, status variable is set to 0x00000040 and
BIT MCI_CMDRESPEND is cleared by writing MMCICLEAR register.
Then mmci_cmd_irq() is called. Considering the following conditions:
- host->busy_status is 0,
- this is a "busy response",
- reading again MMCISTATUS register gives 0x1000400,
MMCIMASK0 is updated to unmask MCI_ST_BUSYEND bit.
Thus, MMCIMASK0 is set to 0x010003FF and host->busy_status is set to wait
for busy end completion.
Back again in status loop of mmci_irq(), we quickly go through
mmci_data_irq() as there are no data in that case. And we finally go
through following test at the end of while(status) loop:
/*
* Don't poll for busy completion in irq context.
*/
if (host->variant->busy_detect && host->busy_status)
status &= ~host->variant->busy_detect_flag;
Because status variable is not yet null (is equal to 0x40), we do not leave
interrupt context yet but we loop again into while(status) loop. So we run
across following steps:
a) MMCISTATUS register is read again and this time is equal to 0x01000400.
So that following bits are set:
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is equal to 0x010003FF:
b) status variable is set to 0x01000000.
c) MCI_ST_CARDBUSY bit is cleared by writing MMCICLEAR register.
Then, mmci_cmd_irq() is called one more time. Since host->busy_status is
set and that MCI_ST_CARDBUSY is set in status variable, we just return from
this function.
Back again in mmci_irq(), status variable is set to 0 and we finally leave
the while(status) loop. As a result we leave interrupt context, waiting for
busy end interrupt event.
Now, consider that busy end completion is raised IN BETWEEN steps 3.a) and
3.c). In such a case, we may mistakenly clear busy end interrupt at step
3.c) while it has not yet been processed. This will result in mmc command
to wait forever for a busy end completion that will never happen.
To fix the problem, this patch implements the following changes:
Considering that the mmci seems to be triggering the IRQ on both edges
while monitoring DAT0 for busy completion and that same status bit is used
to monitor start and end of busy detection, special care must be taken to
make sure that both start and end interrupts are always cleared one after
the other.
1) Clearing of card busy bit is moved in mmc_cmd_irq() function where
unmasking of busy end bit is effectively handled.
2) Just before unmasking busy end event, busy start event is cleared by
writing card busy bit in MMCICLEAR register.
3) Finally, once we are no more busy with a command, busy end event is
cleared writing again card busy bit in MMCICLEAR register.
This patch has been tested with the ST Accordo5 machine, not yet supported
upstream but relies on the mmci driver.
Signed-off-by: Sarang Mairal <sarang.mairal@garmin.com>
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Apparently there are machines out there with Skylake CPU and KabyPoint
PCH. Judging from our driver code, there doesn't seem to be any code
paths that would do anything different between SunrisePoint and
KabyPoint PCHs, so it would seem okay to accept the combo without
warnings.
Fixes: 22dea0be50b2 ("drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.")
References: https://lists.freedesktop.org/archives/intel-gfx/2017-February/118611.html
Reported-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485956769-26015-1-git-send-email-jani.nikula@intel.com
(cherry picked from commit 3aac4acb89710fe782c9e78e7b1febf76e112c6c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Commit 920cf4194954ec ("drm/i915: Introduce an internal allocator for
disposable private objects") introduced a regression for the kernel
running as Xen dom0: when switching to graphics mode a GPU HANG
occurred.
Reason seems to be a missing adaption similar to that done in
commit 7453c549f5f648 ("swiotlb: Export swiotlb_max_segment to users")
to i915_gem_object_get_pages_internal().
So limit the maximum page order to be used according to the maximum
swiotlb segment size instead to the complete swiotlb size.
Fixes: 920cf4194954 ("drm/i915: Introduce an internal allocator for disposable private objects")
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202094711.939-1-jgross@suse.com
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 5584f1b1d73e9cc95092734c316e467c6c4468f9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
On a non-llc system, the objects are created with .cache_level =
CACHE_NONE and so the transition to uncached for scanout is a no-op.
However, if the object was never written to, it will still be in the CPU
domain (having been zeroed out by shmemfs). Those cachelines need to be
flushed prior to display.
Reported-and-tested-by: Vito Caputo
Fixes: a6a7cc4b7db6 ("drm/i915: Always flush the dirty CPU cache when pinning the scanout")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170109111932.6342-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 69aeafeae9b30d797c439a30d1a4ccc8dc5b0eb0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
page_flip_completed() dereferences 'work' variable after executing
queue_work(). This is not safe as the 'work' item might be already freed
by queued work:
BUG: KASAN: use-after-free in page_flip_completed+0x3ff/0x490 at addr ffff8803dc010f90
Call Trace:
__asan_report_load8_noabort+0x59/0x80
page_flip_completed+0x3ff/0x490
intel_finish_page_flip_mmio+0xe3/0x130
intel_pipe_handle_vblank+0x2d/0x40
gen8_irq_handler+0x4a7/0xed0
__handle_irq_event_percpu+0xf6/0x860
handle_irq_event_percpu+0x6b/0x160
handle_irq_event+0xc7/0x1b0
handle_edge_irq+0x1f4/0xa50
handle_irq+0x41/0x70
do_IRQ+0x9a/0x200
common_interrupt+0x89/0x89
Freed:
kfree+0x113/0x4d0
intel_unpin_work_fn+0x29a/0x3b0
process_one_work+0x79e/0x1b70
worker_thread+0x611/0x1460
kthread+0x241/0x3a0
ret_from_fork+0x27/0x40
Move queue_work() after trace_i915_flip_complete() to fix this.
Fixes: e5510fac98a7 ("drm/i915: add tracepoints for flip requests & completions")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: <stable@vger.kernel.org> # v2.6.36+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126143211.24013-1-aryabinin@virtuozzo.com
(cherry picked from commit 05c41f926fcc7ef838c80a6a99d84f67b4e0b824)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
git://people.freedesktop.org/~syeh/repos_linux into drm-fixes
Single vmwgfx boot crasher fix.
* 'drm-vmwgfx-fixes-4_10' of git://people.freedesktop.org/~syeh/repos_linux:
drm/vmwgfx: Fix depth input into drm_mode_legacy_fb_format
|
