diff options
-rw-r--r-- | arch/arm/mach-ux500/board-mop500-sdi.c | 32 | ||||
-rw-r--r-- | arch/arm/mach-ux500/board-u5500-sdi.c | 244 |
2 files changed, 240 insertions, 36 deletions
diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c index 920251cf834..14a7b6e69d0 100644 --- a/arch/arm/mach-ux500/board-mop500-sdi.c +++ b/arch/arm/mach-ux500/board-mop500-sdi.c @@ -11,15 +11,16 @@ #include <linux/amba/mmci.h> #include <linux/mmc/host.h> #include <linux/platform_device.h> +#include <linux/delay.h> #include <asm/mach-types.h> #include <plat/ste_dma40.h> #include <mach/devices.h> #include <mach/hardware.h> +#include <mach/ste-dma40-db8500.h> #include "devices-db8500.h" #include "board-mop500.h" -#include "ste-dma40-db8500.h" /* * v2 has a new version of this block that need to be forced, the number found @@ -50,6 +51,7 @@ static int mop500_sdi0_ios_handler(struct device *dev, struct mmc_ios *ios) */ gpio_direction_output(sdi0_vsel, 0); gpio_direction_output(sdi0_en, 1); + udelay(100); break; case MMC_POWER_OFF: gpio_direction_output(sdi0_vsel, 0); @@ -64,19 +66,23 @@ static int mop500_sdi0_ios_handler(struct device *dev, struct mmc_ios *ios) struct stedma40_chan_cfg mop500_sdi0_dma_cfg_rx = { .mode = STEDMA40_MODE_LOGICAL, .dir = STEDMA40_PERIPH_TO_MEM, - .src_dev_type = DB8500_DMA_DEV29_SD_MM0_RX, + .src_dev_type = DB8500_DMA_DEV1_SD_MMC0_RX, .dst_dev_type = STEDMA40_DEV_DST_MEMORY, .src_info.data_width = STEDMA40_WORD_WIDTH, .dst_info.data_width = STEDMA40_WORD_WIDTH, + .use_fixed_channel = true, + .phy_channel = 0, }; static struct stedma40_chan_cfg mop500_sdi0_dma_cfg_tx = { .mode = STEDMA40_MODE_LOGICAL, .dir = STEDMA40_MEM_TO_PERIPH, .src_dev_type = STEDMA40_DEV_SRC_MEMORY, - .dst_dev_type = DB8500_DMA_DEV29_SD_MM0_TX, + .dst_dev_type = DB8500_DMA_DEV1_SD_MMC0_TX, .src_info.data_width = STEDMA40_WORD_WIDTH, .dst_info.data_width = STEDMA40_WORD_WIDTH, + .use_fixed_channel = true, + .phy_channel = 0, }; #endif @@ -121,14 +127,6 @@ static void sdi0_configure(struct device *parent) db8500_add_sdi0(parent, &mop500_sdi0_data, U8500_SDI_V2_PERIPHID); } -void mop500_sdi_tc35892_init(struct device *parent) -{ - mop500_sdi0_data.gpio_cd = GPIO_SDMMC_CD; - sdi0_en = GPIO_SDMMC_EN; - sdi0_vsel = GPIO_SDMMC_1V8_3V_SEL; - sdi0_configure(parent); -} - /* * SDI1 (SDIO WLAN) */ @@ -241,6 +239,16 @@ static struct mmci_platform_data mop500_sdi4_data = { #endif }; +void mop500_sdi_tc35892_init(struct device *parent) +{ + mop500_sdi0_data.gpio_cd = GPIO_SDMMC_CD; + sdi0_en = GPIO_SDMMC_EN; + sdi0_vsel = GPIO_SDMMC_1V8_3V_SEL; + sdi0_configure(parent); + /* WLAN SDIO channel */ + db8500_add_sdi1(parent, &mop500_sdi1_data, U8500_SDI_V2_PERIPHID); +} + void __init mop500_sdi_init(struct device *parent) { /* PoP:ed eMMC */ @@ -267,6 +275,8 @@ void __init snowball_sdi_init(struct device *parent) sdi0_en = SNOWBALL_SDMMC_EN_GPIO; sdi0_vsel = SNOWBALL_SDMMC_1V8_3V_GPIO; sdi0_configure(parent); + /* WLAN SDIO channel */ + db8500_add_sdi1(parent, &mop500_sdi1_data, U8500_SDI_V2_PERIPHID); } void __init hrefv60_sdi_init(struct device *parent) diff --git a/arch/arm/mach-ux500/board-u5500-sdi.c b/arch/arm/mach-ux500/board-u5500-sdi.c index 836112eedde..de6e0e5192b 100644 --- a/arch/arm/mach-ux500/board-u5500-sdi.c +++ b/arch/arm/mach-ux500/board-u5500-sdi.c @@ -5,34 +5,28 @@ * License terms: GNU General Public License (GPL) version 2 */ +#include <linux/kernel.h> +#include <linux/gpio.h> +#include <linux/amba/bus.h> #include <linux/amba/mmci.h> #include <linux/mmc/host.h> +#include <linux/platform_device.h> +#include <linux/delay.h> -#include <plat/pincfg.h> -#include <plat/gpio-nomadik.h> -#include <mach/db5500-regs.h> +#include <asm/mach-types.h> #include <plat/ste_dma40.h> +#include <mach/devices.h> +#include <mach/hardware.h> +#include <mach/ste-dma40-db5500.h> -#include "pins-db5500.h" #include "devices-db5500.h" -#include "ste-dma40-db5500.h" - -static pin_cfg_t u5500_sdi_pins[] = { - /* SDI0 (POP eMMC) */ - GPIO5_MC0_DAT0 | PIN_DIR_INPUT | PIN_PULL_UP, - GPIO6_MC0_DAT1 | PIN_DIR_INPUT | PIN_PULL_UP, - GPIO7_MC0_DAT2 | PIN_DIR_INPUT | PIN_PULL_UP, - GPIO8_MC0_DAT3 | PIN_DIR_INPUT | PIN_PULL_UP, - GPIO9_MC0_DAT4 | PIN_DIR_INPUT | PIN_PULL_UP, - GPIO10_MC0_DAT5 | PIN_DIR_INPUT | PIN_PULL_UP, - GPIO11_MC0_DAT6 | PIN_DIR_INPUT | PIN_PULL_UP, - GPIO12_MC0_DAT7 | PIN_DIR_INPUT | PIN_PULL_UP, - GPIO13_MC0_CMD | PIN_DIR_INPUT | PIN_PULL_UP, - GPIO14_MC0_CLK | PIN_DIR_OUTPUT | PIN_VAL_LOW, -}; +#include "board-u5500.h" +/* + * SDI 0 (eMMC) + */ #ifdef CONFIG_STE_DMA40 -struct stedma40_chan_cfg u5500_sdi0_dma_cfg_rx = { +static struct stedma40_chan_cfg sdi0_dma_cfg_rx = { .mode = STEDMA40_MODE_LOGICAL, .dir = STEDMA40_PERIPH_TO_MEM, .src_dev_type = DB5500_DMA_DEV24_SDMMC0_RX, @@ -41,7 +35,7 @@ struct stedma40_chan_cfg u5500_sdi0_dma_cfg_rx = { .dst_info.data_width = STEDMA40_WORD_WIDTH, }; -static struct stedma40_chan_cfg u5500_sdi0_dma_cfg_tx = { +static struct stedma40_chan_cfg sdi0_dma_cfg_tx = { .mode = STEDMA40_MODE_LOGICAL, .dir = STEDMA40_MEM_TO_PERIPH, .src_dev_type = STEDMA40_DEV_SRC_MEMORY, @@ -61,14 +55,214 @@ static struct mmci_platform_data u5500_sdi0_data = { .gpio_wp = -1, #ifdef CONFIG_STE_DMA40 .dma_filter = stedma40_filter, - .dma_rx_param = &u5500_sdi0_dma_cfg_rx, - .dma_tx_param = &u5500_sdi0_dma_cfg_tx, + .dma_rx_param = &sdi0_dma_cfg_rx, + .dma_tx_param = &sdi0_dma_cfg_tx, +#endif +}; + +/* + * SDI 1 (MicroSD slot) + */ + +/* MMCIPOWER bits */ +#define MCI_DATA2DIREN (1 << 2) +#define MCI_CMDDIREN (1 << 3) +#define MCI_DATA0DIREN (1 << 4) +#define MCI_DATA31DIREN (1 << 5) +#define MCI_FBCLKEN (1 << 7) + +static u32 u5500_sdi1_vdd_handler(struct device *dev, unsigned int vdd, + unsigned char power_mode) +{ + switch (power_mode) { + case MMC_POWER_UP: + case MMC_POWER_ON: + /* + * Level shifter voltage should depend on vdd to when deciding + * on either 1.8V or 2.9V. Once the decision has been made the + * level shifter must be disabled and re-enabled with a changed + * select signal in order to switch the voltage. Since there is + * no framework support yet for indicating 1.8V in vdd, use the + * default 2.9V. + */ + gpio_set_value_cansleep(GPIO_MMC_CARD_CTRL, 1); + udelay(100); + break; + case MMC_POWER_OFF: + gpio_set_value_cansleep(GPIO_MMC_CARD_CTRL, 0); + break; + } + + return MCI_FBCLKEN | MCI_CMDDIREN | MCI_DATA0DIREN | + MCI_DATA2DIREN; +} + +static struct stedma40_chan_cfg sdi1_dma_cfg_rx = { + .mode = STEDMA40_MODE_LOGICAL, + .dir = STEDMA40_PERIPH_TO_MEM, + .src_dev_type = DB5500_DMA_DEV25_SDMMC1_RX, + .dst_dev_type = STEDMA40_DEV_DST_MEMORY, + .src_info.data_width = STEDMA40_WORD_WIDTH, + .dst_info.data_width = STEDMA40_WORD_WIDTH, +}; + +static struct stedma40_chan_cfg sdi1_dma_cfg_tx = { + .mode = STEDMA40_MODE_LOGICAL, + .dir = STEDMA40_MEM_TO_PERIPH, + .src_dev_type = STEDMA40_DEV_SRC_MEMORY, + .dst_dev_type = DB5500_DMA_DEV25_SDMMC1_TX, + .src_info.data_width = STEDMA40_WORD_WIDTH, + .dst_info.data_width = STEDMA40_WORD_WIDTH, +}; + +static struct mmci_platform_data u5500_sdi1_data = { + .vdd_handler = u5500_sdi1_vdd_handler, + .ocr_mask = MMC_VDD_29_30, + .f_max = 50000000, + .capabilities = MMC_CAP_4_BIT_DATA | + MMC_CAP_SD_HIGHSPEED | + MMC_CAP_MMC_HIGHSPEED, + .gpio_cd = GPIO_SDMMC_CD, + .gpio_wp = -1, + .cd_invert = true, +#ifdef CONFIG_STE_DMA40 + .dma_filter = stedma40_filter, + .dma_rx_param = &sdi1_dma_cfg_rx, + .dma_tx_param = &sdi1_dma_cfg_tx, +#endif +}; + +/* + * SDI2 (EMMC2) + */ + +static struct stedma40_chan_cfg sdi2_dma_cfg_rx = { + .mode = STEDMA40_MODE_LOGICAL, + .dir = STEDMA40_PERIPH_TO_MEM, + .src_dev_type = DB5500_DMA_DEV26_SDMMC2_RX, + .dst_dev_type = STEDMA40_DEV_DST_MEMORY, + .src_info.data_width = STEDMA40_WORD_WIDTH, + .dst_info.data_width = STEDMA40_WORD_WIDTH, +}; + +static struct stedma40_chan_cfg sdi2_dma_cfg_tx = { + .mode = STEDMA40_MODE_LOGICAL, + .dir = STEDMA40_MEM_TO_PERIPH, + .src_dev_type = STEDMA40_DEV_SRC_MEMORY, + .dst_dev_type = DB5500_DMA_DEV26_SDMMC2_TX, + .src_info.data_width = STEDMA40_WORD_WIDTH, + .dst_info.data_width = STEDMA40_WORD_WIDTH, +}; + +static struct mmci_platform_data u5500_sdi2_data = { + .ocr_mask = MMC_VDD_165_195, + .f_max = 50000000, + .capabilities = MMC_CAP_4_BIT_DATA | + MMC_CAP_8_BIT_DATA | + MMC_CAP_MMC_HIGHSPEED, + .gpio_cd = -1, + .gpio_wp = -1, +#ifdef CONFIG_STE_DMA40 + .dma_filter = stedma40_filter, + .dma_rx_param = &sdi2_dma_cfg_rx, + .dma_tx_param = &sdi2_dma_cfg_tx, #endif }; +/* + * SDI 3 (SDIO WLAN) + */ +#ifdef SDIO_DMA_ON +#ifdef CONFIG_STE_DMA40 +static struct stedma40_chan_cfg sdi3_dma_cfg_rx = { + .mode = STEDMA40_MODE_LOGICAL, + .dir = STEDMA40_PERIPH_TO_MEM, + .src_dev_type = DB5500_DMA_DEV27_SDMMC3_RX, + .dst_dev_type = STEDMA40_DEV_DST_MEMORY, + .src_info.data_width = STEDMA40_WORD_WIDTH, + .dst_info.data_width = STEDMA40_WORD_WIDTH, +}; + +static struct stedma40_chan_cfg sdi3_dma_cfg_tx = { + .mode = STEDMA40_MODE_LOGICAL, + .dir = STEDMA40_MEM_TO_PERIPH, + .src_dev_type = STEDMA40_DEV_SRC_MEMORY, + .dst_dev_type = DB5500_DMA_DEV27_SDMMC3_TX, + .src_info.data_width = STEDMA40_WORD_WIDTH, + .dst_info.data_width = STEDMA40_WORD_WIDTH, +}; +#endif +#endif + +static struct mmci_platform_data u5500_sdi3_data = { + .ocr_mask = MMC_VDD_29_30, + .f_max = 50000000, + .capabilities = MMC_CAP_4_BIT_DATA, + .gpio_cd = -1, + .gpio_wp = -1, +#ifdef SDIO_DMA_ON +#ifdef CONFIG_STE_DMA40 + .dma_filter = stedma40_filter, + .dma_rx_param = &sdi3_dma_cfg_rx, + .dma_tx_param = &sdi3_dma_cfg_tx, +#endif +#endif +}; + +static void sdi1_configure(void) +{ + int pin[2]; + int ret; + + /* Level-shifter GPIOs */ + pin[0] = GPIO_MMC_CARD_CTRL; + pin[1] = GPIO_MMC_CARD_VSEL; + + ret = gpio_request(pin[0], "MMC_CARD_CTRL"); + if (!ret) + ret = gpio_request(pin[1], "MMC_CARD_VSEL"); + + if (ret) { + pr_warning("unable to config sdi0 gpios for level shifter.\n"); + return; + } + /* Select the default 2.9V and eanble level shifter */ + gpio_direction_output(pin[0], 1); + gpio_direction_output(pin[1], 0); +} + +#define SDI_PID_V1 0x00480180 +#define SDI_PID_V2 0x10480180 +#define BACKUPRAM_ROM_DEBUG_ADDR 0xFFC +#define MMC_BLOCK_ID 0x20 void __init u5500_sdi_init(struct device *parent) { - nmk_config_pins(u5500_sdi_pins, ARRAY_SIZE(u5500_sdi_pins)); + u32 periphid = 0; + int mmc_blk = 0; + + if (cpu_is_u5500v1()) + periphid = SDI_PID_V1; + else + periphid = SDI_PID_V2; + + if (cpu_is_u5500v2()) + /* + * Fix me in 5500 v2.1 + * Dynamic detection of booting device by reading + * ROM debug register from BACKUP RAM and register the + * corresponding EMMC. + * This is done due to wrong configuration of MMC0 clock + * in ROM code for u5500 v2. + */ + mmc_blk = readl(__io_address(U5500_BACKUPRAM1_BASE) + + BACKUPRAM_ROM_DEBUG_ADDR); + + if (mmc_blk & MMC_BLOCK_ID) + db5500_add_sdi2(parent, &u5500_sdi2_data, periphid); + else + db5500_add_sdi0(parent, &u5500_sdi0_data, periphid); - db5500_add_sdi0(parent, &u5500_sdi0_data); + sdi1_configure(); + db5500_add_sdi1(parent, &u5500_sdi1_data, periphid); + db5500_add_sdi3(parent, &u5500_sdi3_data, periphid); } |