diff options
Diffstat (limited to 'arch/arm/mach-ux500/board-mop500-sdi.c')
| -rw-r--r-- | arch/arm/mach-ux500/board-mop500-sdi.c | 172 |
1 files changed, 107 insertions, 65 deletions
diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c index ae484d6b74e..e043a31ce25 100644 --- a/arch/arm/mach-ux500/board-mop500-sdi.c +++ b/arch/arm/mach-ux500/board-mop500-sdi.c @@ -11,6 +11,7 @@ #include <linux/amba/mmci.h> #include <linux/mmc/host.h> #include <linux/platform_device.h> +#include <linux/delay.h> #include <asm/mach-types.h> #include <plat/ste_dma40.h> @@ -31,72 +32,101 @@ * SDI 0 (MicroSD slot) */ -/* MMCIPOWER bits */ -#define MCI_DATA2DIREN (1 << 2) -#define MCI_CMDDIREN (1 << 3) -#define MCI_DATA0DIREN (1 << 4) -#define MCI_DATA31DIREN (1 << 5) -#define MCI_FBCLKEN (1 << 7) - /* GPIO pins used by the sdi0 level shifter */ static int sdi0_en = -1; static int sdi0_vsel = -1; -static u32 mop500_sdi0_vdd_handler(struct device *dev, unsigned int vdd, - unsigned char power_mode) +static int mop500_sdi0_ios_handler(struct device *dev, struct mmc_ios *ios) { - switch (power_mode) { + static unsigned char power_mode = MMC_POWER_ON; + static unsigned char signal_voltage = MMC_SIGNAL_VOLTAGE_330; + + if (signal_voltage == ios->signal_voltage) + goto do_power; + + /* + * We need to re-init the levelshifter when switching I/O voltage level. + * Max discharge time according to ST6G3244ME spec is 1 ms. + */ + if (power_mode == MMC_POWER_ON) { + power_mode = MMC_POWER_OFF; + gpio_direction_output(sdi0_en, 0); + msleep(1); + } + + switch (ios->signal_voltage) { + case MMC_SIGNAL_VOLTAGE_330: + gpio_direction_output(sdi0_vsel, 0); + break; + case MMC_SIGNAL_VOLTAGE_180: + gpio_direction_output(sdi0_vsel, 1); + break; + default: + pr_warning("Non supported signal voltage for levelshifter.\n"); + break; + } + + signal_voltage = ios->signal_voltage; + +do_power: + if (power_mode == ios->power_mode) + return 0; + + switch (ios->power_mode) { case MMC_POWER_UP: + break; case MMC_POWER_ON: - /* - * Level shifter voltage should depend on vdd to when deciding - * on either 1.8V or 2.9V. Once the decision has been made the - * level shifter must be disabled and re-enabled with a changed - * select signal in order to switch the voltage. Since there is - * no framework support yet for indicating 1.8V in vdd, use the - * default 2.9V. - */ - gpio_direction_output(sdi0_vsel, 0); gpio_direction_output(sdi0_en, 1); + /* Max settling time according to ST6G3244ME spec is 100 us. */ + udelay(100); break; case MMC_POWER_OFF: - gpio_direction_output(sdi0_vsel, 0); gpio_direction_output(sdi0_en, 0); break; } - return MCI_FBCLKEN | MCI_CMDDIREN | MCI_DATA0DIREN | - MCI_DATA2DIREN | MCI_DATA31DIREN; + power_mode = ios->power_mode; + + return 0; } #ifdef CONFIG_STE_DMA40 struct stedma40_chan_cfg mop500_sdi0_dma_cfg_rx = { .mode = STEDMA40_MODE_LOGICAL, .dir = STEDMA40_PERIPH_TO_MEM, - .src_dev_type = DB8500_DMA_DEV29_SD_MM0_RX, + .src_dev_type = DB8500_DMA_DEV1_SD_MMC0_RX, .dst_dev_type = STEDMA40_DEV_DST_MEMORY, .src_info.data_width = STEDMA40_WORD_WIDTH, .dst_info.data_width = STEDMA40_WORD_WIDTH, + .use_fixed_channel = true, + .phy_channel = 0, }; static struct stedma40_chan_cfg mop500_sdi0_dma_cfg_tx = { .mode = STEDMA40_MODE_LOGICAL, .dir = STEDMA40_MEM_TO_PERIPH, .src_dev_type = STEDMA40_DEV_SRC_MEMORY, - .dst_dev_type = DB8500_DMA_DEV29_SD_MM0_TX, + .dst_dev_type = DB8500_DMA_DEV1_SD_MMC0_TX, .src_info.data_width = STEDMA40_WORD_WIDTH, .dst_info.data_width = STEDMA40_WORD_WIDTH, + .use_fixed_channel = true, + .phy_channel = 0, }; #endif static struct mmci_platform_data mop500_sdi0_data = { - .vdd_handler = mop500_sdi0_vdd_handler, - .ocr_mask = MMC_VDD_29_30, + .ios_handler = mop500_sdi0_ios_handler, .f_max = 50000000, .capabilities = MMC_CAP_4_BIT_DATA | MMC_CAP_SD_HIGHSPEED | - MMC_CAP_MMC_HIGHSPEED, + MMC_CAP_MMC_HIGHSPEED | + MMC_CAP_UHS_SDR12 | + MMC_CAP_UHS_SDR25, .gpio_wp = -1, + .sigdir = MCI_ST_FBCLKEN | + MCI_ST_CMDDIREN | + MCI_ST_DATA0DIREN | + MCI_ST_DATA2DIREN, #ifdef CONFIG_STE_DMA40 .dma_filter = stedma40_filter, .dma_rx_param = &mop500_sdi0_dma_cfg_rx, @@ -104,36 +134,6 @@ static struct mmci_platform_data mop500_sdi0_data = { #endif }; -static void sdi0_configure(void) -{ - int ret; - - ret = gpio_request(sdi0_en, "level shifter enable"); - if (!ret) - ret = gpio_request(sdi0_vsel, - "level shifter 1v8-3v select"); - - if (ret) { - pr_warning("unable to config sdi0 gpios for level shifter.\n"); - return; - } - - /* Select the default 2.9V and enable level shifter */ - gpio_direction_output(sdi0_vsel, 0); - gpio_direction_output(sdi0_en, 1); - - /* Add the device, force v2 to subrevision 1 */ - db8500_add_sdi0(&mop500_sdi0_data, U8500_SDI_V2_PERIPHID); -} - -void mop500_sdi_tc35892_init(void) -{ - mop500_sdi0_data.gpio_cd = GPIO_SDMMC_CD; - sdi0_en = GPIO_SDMMC_EN; - sdi0_vsel = GPIO_SDMMC_1V8_3V_SEL; - sdi0_configure(); -} - /* * SDI1 (SDIO WLAN) */ @@ -170,10 +170,40 @@ static struct mmci_platform_data mop500_sdi1_data = { #endif }; +static void sdi0_sdi1_configure(void) +{ + int ret; + + ret = gpio_request(sdi0_en, "level shifter enable"); + if (!ret) + ret = gpio_request(sdi0_vsel, + "level shifter 1v8-3v select"); + + if (ret) { + pr_warning("unable to config sdi0 gpios for level shifter.\n"); + return; + } + + /* Select the default 2.9V and enable level shifter */ + gpio_direction_output(sdi0_vsel, 0); + gpio_direction_output(sdi0_en, 1); + + /* Add the device, force v2 to subrevision 1 */ + db8500_add_sdi0(&mop500_sdi0_data, U8500_SDI_V2_PERIPHID); + db8500_add_sdi1(&mop500_sdi1_data, U8500_SDI_V2_PERIPHID); +} + +void mop500_sdi_tc35892_init(void) +{ + mop500_sdi0_data.gpio_cd = GPIO_SDMMC_CD; + sdi0_en = GPIO_SDMMC_EN; + sdi0_vsel = GPIO_SDMMC_1V8_3V_SEL; + sdi0_sdi1_configure(); +} + /* * SDI 2 (POP eMMC, not on DB8500ed) */ - #ifdef CONFIG_STE_DMA40 struct stedma40_chan_cfg mop500_sdi2_dma_cfg_rx = { .mode = STEDMA40_MODE_LOGICAL, @@ -198,7 +228,9 @@ static struct mmci_platform_data mop500_sdi2_data = { .ocr_mask = MMC_VDD_165_195, .f_max = 50000000, .capabilities = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA | - MMC_CAP_MMC_HIGHSPEED, + MMC_CAP_MMC_HIGHSPEED | + MMC_CAP_ERASE, + .capabilities2 = MMC_CAP2_NO_SLEEP_CMD, .gpio_cd = -1, .gpio_wp = -1, #ifdef CONFIG_STE_DMA40 @@ -233,7 +265,6 @@ static struct stedma40_chan_cfg mop500_sdi4_dma_cfg_tx = { #endif static struct mmci_platform_data mop500_sdi4_data = { - .ocr_mask = MMC_VDD_29_30, .f_max = 50000000, .capabilities = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA | MMC_CAP_MMC_HIGHSPEED, @@ -253,7 +284,7 @@ void __init mop500_sdi_init(void) /* On-board eMMC */ db8500_add_sdi4(&mop500_sdi4_data, U8500_SDI_V2_PERIPHID); /* - * On boards with the TC35892 GPIO expander, sdi0 will finally + * On boards with the TC35892 GPIO expander, sdi0 and sdi1 will finally * be added when the TC35892 initializes and calls * mop500_sdi_tc35892_init() above. */ @@ -270,7 +301,7 @@ void __init snowball_sdi_init(void) mop500_sdi0_data.cd_invert = true; sdi0_en = SNOWBALL_SDMMC_EN_GPIO; sdi0_vsel = SNOWBALL_SDMMC_1V8_3V_GPIO; - sdi0_configure(); + sdi0_sdi1_configure(); } void __init hrefv60_sdi_init(void) @@ -283,7 +314,18 @@ void __init hrefv60_sdi_init(void) mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO; sdi0_en = HREFV60_SDMMC_EN_GPIO; sdi0_vsel = HREFV60_SDMMC_1V8_3V_GPIO; - sdi0_configure(); - /* WLAN SDIO channel */ - db8500_add_sdi1(&mop500_sdi1_data, U8500_SDI_V2_PERIPHID); + sdi0_sdi1_configure(); +} + +void __init mach_u8520_sdi_init(void) +{ + /* PoP:ed eMMC */ + db8500_add_sdi2(&mop500_sdi2_data, U8500_SDI_V2_PERIPHID); + /* On-board eMMC */ + db8500_add_sdi4(&mop500_sdi4_data, U8500_SDI_V2_PERIPHID); + /* External Micro SD slot */ + mop500_sdi0_data.gpio_cd = U8520_SDMMC_CD_GPIO; + sdi0_en = U8520_SDMMC_EN_GPIO; + sdi0_vsel = U8520_SDMMC_1V8_3V_GPIO; + sdi0_sdi1_configure(); } |