diff options
Diffstat (limited to 'arch/arm/mach-ux500/board-u5500-cyttsp.c')
| -rw-r--r-- | arch/arm/mach-ux500/board-u5500-cyttsp.c | 144 |
1 files changed, 144 insertions, 0 deletions
diff --git a/arch/arm/mach-ux500/board-u5500-cyttsp.c b/arch/arm/mach-ux500/board-u5500-cyttsp.c new file mode 100644 index 00000000000..47eaa36c030 --- /dev/null +++ b/arch/arm/mach-ux500/board-u5500-cyttsp.c @@ -0,0 +1,144 @@ +/* + * Copyright (C) 2011 ST-Ericsson SA + * Author: Avinash A <avinash.a@stericsson.com> for ST-Ericsson + * License terms:GNU General Public License (GPL) version 2 + */ +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/spi/spi.h> +#include <linux/gpio.h> +#include <linux/cyttsp.h> +#include <linux/delay.h> +#include <linux/amba/pl022.h> +#include <plat/pincfg.h> +#include <mach/hardware.h> + +#include "pins-db5500.h" +#include "board-u5500.h" + +/* cyttsp_gpio_board_init : configures the touch panel. */ +static int cyttsp_plat_init(int on) +{ + int ret; + + ret = gpio_direction_output(CYPRESS_SLAVE_SELECT_GPIO, 1); + if (ret < 0) { + pr_err("slave select gpio direction failed\n"); + gpio_free(CYPRESS_SLAVE_SELECT_GPIO); + return ret; + } + + return 0; +} + +static int cyttsp_wakeup(void) +{ + int ret; + + ret = gpio_request(CYPRESS_TOUCH_INT_PIN, "Wakeup_pin"); + if (ret < 0) { + pr_err("touch gpio failed\n"); + return ret; + } + ret = gpio_direction_output(CYPRESS_TOUCH_INT_PIN, 1); + if (ret < 0) { + pr_err("touch gpio direction failed\n"); + goto out; + } + gpio_set_value(CYPRESS_TOUCH_INT_PIN, 0); + gpio_set_value(CYPRESS_TOUCH_INT_PIN, 1); + /* + * To wake up the controller from sleep + * state the interrupt pin needs to be + * pulsed twice with a delay greater + * than 2 micro seconds. + */ + udelay(3); + gpio_set_value(CYPRESS_TOUCH_INT_PIN, 0); + gpio_set_value(CYPRESS_TOUCH_INT_PIN, 1); + ret = gpio_direction_input(CYPRESS_TOUCH_INT_PIN); + if (ret < 0) { + pr_err("touch gpio direction IN config failed\n"); + goto out; + } +out: + gpio_free(CYPRESS_TOUCH_INT_PIN); + return 0; +} +static struct cyttsp_platform_data cyttsp_spi_platdata = { + .maxx = 480, + .maxy = 854, + .flags = 0, + .gen = CY_GEN3, + .use_st = 0, + .use_mt = 1, + .use_trk_id = 0, + .use_hndshk = 0, + .use_sleep = 1, + .use_gestures = 0, + .use_load_file = 0, + .use_force_fw_update = 0, + .use_virtual_keys = 0, + /* activate up to 4 groups and set active distance */ + .gest_set = CY_GEST_GRP_NONE | CY_ACT_DIST, + /* change scn_type to enable finger and/or stylus detection */ + .scn_typ = 0xA5, /* autodetect finger+stylus; balanced mutual scan */ + .act_intrvl = CY_ACT_INTRVL_DFLT, /* Active refresh interval; ms */ + .tch_tmout = CY_TCH_TMOUT_DFLT, /* Active touch timeout; ms */ + .lp_intrvl = CY_LP_INTRVL_DFLT, /* Low power refresh interval; ms */ + .init = cyttsp_plat_init, + .mt_sync = input_mt_sync, + .wakeup = cyttsp_wakeup, + .name = CY_SPI_NAME, + .irq_gpio = CYPRESS_TOUCH_INT_PIN, + .rst_gpio = CYPRESS_TOUCH_RST_GPIO, +}; + +static void cyttsp_spi_cs_control(u32 command) +{ + if (command == SSP_CHIP_SELECT) + gpio_set_value(CYPRESS_SLAVE_SELECT_GPIO, 0); + else if (command == SSP_CHIP_DESELECT) + gpio_set_value(CYPRESS_SLAVE_SELECT_GPIO, 1); +} + +static struct pl022_config_chip cyttsp_ssp_config_chip = { + .com_mode = INTERRUPT_TRANSFER, + .iface = SSP_INTERFACE_MOTOROLA_SPI, + /* we can act as master only */ + .hierarchy = SSP_MASTER, + .slave_tx_disable = 0, + .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM, + .tx_lev_trig = SSP_TX_16_OR_MORE_EMPTY_LOC, + .ctrl_len = SSP_BITS_16, + .wait_state = SSP_MWIRE_WAIT_ZERO, + .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, + .cs_control = cyttsp_spi_cs_control, +}; + +static struct spi_board_info cypress_spi_devices[] = { + { + .modalias = CY_SPI_NAME, + .controller_data = &cyttsp_ssp_config_chip, + .platform_data = &cyttsp_spi_platdata, + .max_speed_hz = 1000000, + .bus_num = 1, + .chip_select = 0, + .mode = SPI_MODE_0, + } +}; + +void u5500_cyttsp_init(void) +{ + int ret = 0; + + ret = gpio_request(CYPRESS_SLAVE_SELECT_GPIO, "slave_select_gpio"); + if (ret < 0) { + pr_err("slave select gpio failed\n"); + return; + } + if (cpu_is_u5500v2()) + cyttsp_spi_platdata.invert = true; + spi_register_board_info(cypress_spi_devices, + ARRAY_SIZE(cypress_spi_devices)); +} |