| Age | Commit message (Collapse) | Author |
|---|
|
Per Amit's request, enabling SCHED_MC on SMP board defconfigs
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Conflicts:
arch/arm/kernel/entry-armv.S
|
|
|
|
This patch introduces the helper of ehci_sync_mem to flush
qtd/qh into memory immediately on some ARM, so that HC can
see the up-to-date qtd/qh descriptor asap.
This patch fixs one performance bug on ARM Cortex A9 dual core
platform, which has been reported on quite a few ARM machines
(OMAP4, Tegra 2, snowball...), see details from link of
https://bugs.launchpad.net/bugs/709245.
The patch has been tested ok on OMAP4 panda A1 board, and the
performance of 'dd' over usb mass storage can be increased from
4~5MB/sec to 14~16MB/sec after applying this patch.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
|
|
While testing suspend/resume on Samsung SMDKV310 and Origen boards it has been
found that while system tries to enter into suspend, during console early
suspend there is warning message due to unbalance in tty locks. Due to this
sometimes system fails to enter into suspend, this patch fixes the tty mutex
unbalancing.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Bug discovered by Jan Kara:
Finally, commit 1449032be17abb69116dbc393f67ceb8bd034f92 returned back
the old IO submission code but apparently it forgot to return the old
handling of uninitialized buffers so we unconditionnaly call
block_write_full_page() without specifying end_io function. So AFAICS
we never convert unwritten extents to written in some cases. For
example when I mount the fs as: mount -t ext4 -o
nomblk_io_submit,dioread_nolock /dev/ubdb /mnt and do
int fd = open(argv[1], O_RDWR | O_CREAT | O_TRUNC, 0600);
char buf[1024];
memset(buf, 'a', sizeof(buf));
fallocate(fd, 0, 0, 16384);
write(fd, buf, sizeof(buf));
I get a file full of zeros (after remounting the filesystem so that
pagecache is dropped) instead of seeing the first KB contain 'a's.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Change-Id: I349e4e807d2f8bc3573a5e1b2393212e00ca7650
Signed-off-by: Ken Sumrall <ksumrall@android.com>
|
|
If the console_lock was held while the system was rebooted, the messages
in the temporary logbuffer would not have propogated to all the console
drivers.
This force releases the console lock if it failed to be acquired.
Change-Id: I193dcf7b968be17966833e50b8b8bc70d5d9fe89
Signed-off-by: Dima Zavin <dima@android.com>
|
|
Change-Id: I25a516ca4d8f5edc72a2a54e420f5e1b4fe3aa16
Signed-off-by: Howard M. Harte <hharte@broadcom.com>
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
|
|
When v6 and >=v7 boards are supported in the same kernel, the
__und_usr code currently makes a build-time assumption that Thumb-2
instructions occurring in userspace don't need to be supported.
Strictly speaking this is incorrect.
This patch fixes the above case by doing a run-time check on the
CPU architecture in these cases. This only affects kernels which
support v6 and >=v7 CPUs together: plain v6 and plain v7 kernels
are unaffected.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(cherry picked from commit 07ed43553f9ceefe5e3cbd25da0f6ff912b4fedb)
|
|
instructions
When testing whether a Thumb-2 instruction is 32 bits long or not,
the masking done in order to test bits 11-15 of the first
instruction halfword won't affect the result of the comparison, so
remove it.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(cherry picked from commit 948e32025349faaa1cd0a55dc669cc7da095b21d)
|
|
The CPU architecture really should not be changing at runtime, so
make it a global variable instead of a function.
The cpu_architecture() function declared in <asm/system.h> remains
the correct way to read this variable from C code.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(cherry picked from commit db9c84ccacb0e7a7903117929cf1dc914f82fc90)
|
|
This is required to use SWRESET.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
(cherry picked from commit d2edddf2b25863ec0893635662b0832f9965b543)
|
|
/proc/net/xt_qtaguid/ctrl will now show:
active tagged sockets: lines of "sock=%p tag=0x%llx (uid=%u)"
sockets_tagged, : the number of sockets successfully tagged.
sockets_untagged: the number of sockets successfully untagged.
counter_set_changes: ctrl counter set change requests.
delete_cmds: ctrl delete commands completed.
iface_events: number of NETDEV_* events handled.
match_found_sk: sk found in skbuff without ct assist.
match_found_sk_in_ct: the number of times the connection tracker found
a socket for us. This happens when the skbuff didn't have info.
match_found_sk_none: the number of times no sk could be determined
successfully looked up. This indicates we don't know who the
data actually belongs to. This could be unsolicited traffic.
Change-Id: I3a65613bb24852e1eea768ab0320a6a7073ab9be
Signed-off-by: JP Abgrall <jpa@google.com>
|
|
sockfd_put() risks sleeping.
So when doing a delete ctrl command, defer the sockfd_put() and
kfree() to outside of the spinlock.
Change-Id: I5f8ab51d05888d885b2fbb035f61efa5b7abb88a
Signed-off-by: JP Abgrall <jpa@google.com>
|
|
|
|
|
|
At times, it is necessary for boards to provide some additional information
as part of panic logs. Provide information on the board hardware as part
of panic logs.
It is safer to print this information at the very end in case something
bad happens as part of the information retrieval itself.
To use this, set global mach_panic_string to an appropriate string in the
board file.
Change-Id: Id12cdda87b0cd2940dd01d52db97e6162f671b4d
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
|
|
|
|
* Don't hold the sockets after tagging.
sockfd_lookup() does a get() on the associated file.
There was no matching put() so a closed socket could never be
freed.
* Don't rely on struct member order for tag_node
The structs that had a struct tag_node member would work with
the *_tree_* routines only because tag_node was 1st.
* Improve debug messages
Provide info on who the caller is. Use unsigned int for uid.
* Only process NETDEV_UP events.
* Pacifier: disable netfilter matching. Leave .../stats header.
Change-Id: Iccb8ae3cca9608210c417597287a2391010dff2c
Signed-off-by: JP Abgrall <jpa@google.com>
|
|
|
|
commit aba8d056078e47350d85b06a9cabd5afcc4b72ea upstream.
In addition to /etc/perfconfig and $HOME/.perfconfig, perf looks for
configuration in the file ./config, imitating git which looks at
$GIT_DIR/config. If ./config is not a perf configuration file, it
fails, or worse, treats it as a configuration file and changes behavior
in some unexpected way.
"config" is not an unusual name for a file to be lying around and perf
does not have a private directory dedicated for its own use, so let's
just stop looking for configuration in the cwd. Callers needing
context-sensitive configuration can use the PERF_CONFIG environment
variable.
Requested-by: Christian Ohm <chr.ohm@gmx.net>
Cc: 632923@bugs.debian.org
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Christian Ohm <chr.ohm@gmx.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110805165838.GA7237@elie.gateway.2wire.net
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d5811e8731213f80c80d89e980505052f16aca1c upstream.
Attempting to try and turn off disconnected display hw in the
hotput handler lead to more problems than it helped. For
now just register an event and only attempt the do something
interesting with DP. Other connectors are just too problematic:
- Some systems have an HPD pin assigned to LVDS, but it's rarely
if ever connected properly and we don't really care about hpd
events on LVDS anyway since it's always connected.
- The HPD pin is wired up correctly for eDP, but we don't really
have to do anything since the events since it's always connected.
- Some HPD pins fire more than once when you connect/disconnect
- etc.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39882
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 33ae1827d6c3c79c5957536ec29d5a8780623147 upstream.
Need to add support for 4 crtcs when setting the possible crtcs
for the encoders.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 73104b5cfe3067d68f2c2de3f3d4d4964c55873e upstream.
If we get a hotplug event on an connector that is off, don't
attempt to turn it on or off, it should already be off.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=728228
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e22a539824e8ddb82c87b4f415165ede82e6ab56 upstream.
The CONFIG_RELOCATABLE code tries to align the unpack destination to
the value of 'kernel_alignment' in the setup_hdr. If that's 0, it
tries to unpack to address 0, which in fact causes the gunzip code
to call 'error("Out of memory while allocating output buffer")'.
The bootloader (ie. the lguest Launcher in this case) should be doing
setting this field; the normal bzImage is 16M, we can use the same.
Reported-by: Stefanos Geraggelos <sgerag@cslab.ece.ntua.gr>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f982f91516fa4cfd9d20518833cd04ad714585be upstream.
Commit db64fe02258f ("mm: rewrite vmap layer") introduced code that does
address calculations under the assumption that VMAP_BLOCK_SIZE is a
power of two. However, this might not be true if CONFIG_NR_CPUS is not
set to a power of two.
Wrong vmap_block index/offset values could lead to memory corruption.
However, this has never been observed in practice (or never been
diagnosed correctly); what caught this was the BUG_ON in vb_alloc() that
checks for inconsistent vmap_block indices.
To fix this, ensure that VMAP_BLOCK_SIZE always is a power of two.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=31572
Reported-by: Pavel Kysilka <goldenfish@linuxsoft.cz>
Reported-by: Matias A. Fonzo <selk@dragora.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bdc71bc59231f5542af13b5061b9ab124d093050 upstream.
This cleans up error handling for the beacon in case of dma mapping
failure. We need to free the skb when dma mapping fails instead of
nulling and leaking the pointer, and we should bail out to avoid
giving the hardware the bad descriptor.
Finally, we need to perform the null check after trying to update
the beacon, or else beacons will never be sent after a single
mapping failure.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 29591ed4ac6fe00e3ff23b5be0cdc7016ef9c47e upstream.
Two issues were preventing module snd-soc-tegra-wm8903.ko from being
removed and re-inserted:
a) The speaker-enable GPIO is hosted by the WM8903 chip. This GPIO must
be freed before snd_soc_unregister_card() is called, because that
triggers wm8903.c:wm8903_remove(), which calls gpiochip_remove(), which
then fails if any of the GPIOs are in use. To solve this, free all GPIOs
first, so the code doesn't care where they come from.
b) We need to call snd_soc_jack_free_gpios() to match the call to
snd_soc_jack_add_gpios() during initialization. Without this, the
call to snd_soc_jack_add_gpios() fails during any subsequent modprobe
and initialization, since the GPIO and IRQ are already registered. In
turn, this causes the headphone state not to be monitored, so the
headphone is assumed not to be plugged in, and the audio path to it is
never enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a96edd59b2bc88b3d1ea47e0ba48076d65db9302 upstream.
Not all PCM devices have all sub-streams. Specifically, the SPDIF driver
only supports playback and hence has no capture substream. Check whether
a substream exists before dereferencing it, when de-allocating DMA
buffers in tegra_pcm_deallocate_dma_buffer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6678050442e90a4e9511a9ed14b9bdfc5e393323 upstream.
The I2C address is misformatted and would never match.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 15439bde3af7ff88459ea2b5520b77312e958df2 upstream.
This fixes faulty outbount packets in case the inbound packets
received from the hardware are fragmented and contain bogus input
iso frames. The bug has been there for ages, but for some strange
reasons, it was only triggered by newer machines in 64bit mode.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: William Light <wrl@illest.net>
Reported-by: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 66a89b2164e2d30661edbd1953eacf0594d8203a upstream.
rs_resp is dynamically allocated in aem_read_sensor(), so it should be freed
before exiting in every case. This collects the kfree and the return at
the end of the function.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a08af810cdc29d2ca930e8a869d3d01744c392d8 upstream.
Reported-by: Pascal Hambourg <pascal@plouf.fr.eu.org>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 35e9e21fb30dc4452b33aed5cbf233743bffca40 upstream.
This patch adds the product ID of Huawei's Vodafone K4511 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0930bb46bbbb43afe3381ece2cb2f8a5bc3fb544 upstream.
This patch adds the product ID of Huawei's Vodafone K4510 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e2949080792256d1c979aaf30ecd4cab42829f87 upstream.
This patch adds the product ID of Huawei's Vodafone K3771 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 07b21fd83606263fe6f327b98774d51e13e502fd upstream.
This patch adds the product ID of Huawei's Vodafone K3770 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e468561739fffb972d486b98f66c723936335136 upstream.
A new device ID pair is added for Qualcomm Modem present in Sagemcom's HiLo3G module.
Signed-off-by: Vijay Chavan <VijayChavan007@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a871e4f5519d8c52430052e1d340dd5710eb5ad6 upstream.
Connecting the V2M to a Linux host results in a constant stream of
errors spammed to the console, all of the form
sd 1:0:0:0: ioctl_internal_command return code = 8070000
: Sense Key : 0x4 [current]
: ASC=0x0 ASCQ=0x0
The errors appear to be otherwise harmless. Add an unusual_devs entry
which eliminates all of the error messages.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1862cdd542025218f7a390b7e6ddc83a1362d1e0 upstream.
Even if it's unlikely for this to cause an error,
there is a typo in the code that uses the bitwise-AND
operator instead of the logical one.
Signed-off-by: Ionut Nicu <ionut.nicu@cloudbit.ro>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4f1a7a3e78037721496283ea3e87cfefc64d99c7 upstream.
Assign operator instead of equality test in the usbtmc_ioctl_abort_bulk_in() function.
Signed-off-by: Maxim A. Nikulin <M.A.Nikulin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 72c487dfb94d02025fb7437dfe2314d836d5a9ab upstream.
an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.
the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.
in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.
[ balbi@ti.com : simplified commit log; removed few things
which didn't belong there ]
Reported-by: Zach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7de7c7d2cb49900e0b967be871bf695c7d6135c9 upstream.
wMaxPacketSize is __le16 and should be accessed as such. Also fix the
wBytesPerInterval assignment while here.
v2: also fix the wBytesPerInterval assigment, noticed by Matt Evans
This patch should be backported to the 3.0 kernel.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7bd89b4017f46a9b92853940fd9771319acb578a upstream.
Commit fccf4e86200b8f5edd9a65da26f150e32ba79808
"USB: Free bandwidth when usb_disable_device is called" caused a bit of an
issue when the xHCI host controller driver is unloaded. It changed the
USB core to remove all endpoints when a USB device is disabled. When the
driver is unloaded, it will remove the SuperSpeed split root hub, which
will disable all devices under that roothub and then halt the host
controller. When the second High Speed split roothub is removed, the USB
core will attempt to disable the endpoints, which will submit a Configure
Endpoint command to a halted host controller.
The command will eventually time out, but it makes the xHCI driver unload
take *minutes* if there are a couple of USB 1.1/2.0 devices attached. We
must halt the host controller when the SuperSpeed roothub is removed,
because we can't allow any interrupts from things like port status
changes.
Make several different functions not submit commands or URBs to the host
controller when the host is halted, by adding a check in
xhci_check_args(). xhci_check_args() is used by these functions:
xhci.c-int xhci_urb_enqueue()
xhci.c-int xhci_drop_endpoint()
xhci.c-int xhci_add_endpoint()
xhci.c-int xhci_check_bandwidth()
xhci.c-void xhci_reset_bandwidth()
xhci.c-static int xhci_check_streams_endpoint()
xhci.c-int xhci_discover_or_reset_device()
It's also used by xhci_free_dev(). However, we have to take special
care in that case, because we want the device memory to be freed if the
host controller is halted.
This patch should be backported to the 2.6.39 and 3.0 kernel.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6768458b17f9bf48a4c3a34e49b20344091b5f7e upstream.
Software should set XHCI_HC_OS_OWNED bit to request ownership of xHC.
This patch should be backported to kernels as far back as 2.6.31.
Signed-off-by: JiSheng Zhang <jszhang3@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 589c3ca00b7886bf743998398884cd4f4d354e17 upstream.
declaring MODULE_FIRMWARE has apparently forgotten while removing the embedded
firmware arrays in 0a8692b534e18fcec6eac07551bb37a22659f5c7 (rtl8192u_usb:
Remove built-in firmware images).
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Conflicts:
arch/arm/mach-exynos4/Kconfig
arch/arm/mach-exynos4/mach-origen.c
|
|
|
|
|
