From 2eb3e621c4e07e9e7200dbb66f0433b4caafb8e7 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Mon, 12 Mar 2007 15:16:26 -0700 Subject: skge: set mac address bonding fix When bonding does fail over it calls set_mac_address. When this happens as the result of another port going down, the phy_mutex that is common to both ports is held, so it deadlocks. Setting the address doesn't need to do anything that needs the phy_mutex, it already has the RTNL to protect against other admin actions. This change just disables the receiver to avoid any hardware confusion while address is changing. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/skge.c | 28 +++++++++++++++++----------- 1 file changed, 17 insertions(+), 11 deletions(-) diff --git a/drivers/net/skge.c b/drivers/net/skge.c index eea75a401b0..8fecf1b817f 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -3275,24 +3275,30 @@ static int skge_set_mac_address(struct net_device *dev, void *p) struct skge_hw *hw = skge->hw; unsigned port = skge->port; const struct sockaddr *addr = p; + u16 ctrl; if (!is_valid_ether_addr(addr->sa_data)) return -EADDRNOTAVAIL; - mutex_lock(&hw->phy_mutex); memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN); - memcpy_toio(hw->regs + B2_MAC_1 + port*8, - dev->dev_addr, ETH_ALEN); - memcpy_toio(hw->regs + B2_MAC_2 + port*8, - dev->dev_addr, ETH_ALEN); - if (hw->chip_id == CHIP_ID_GENESIS) - xm_outaddr(hw, port, XM_SA, dev->dev_addr); - else { - gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr); - gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr); + /* disable Rx */ + ctrl = gma_read16(hw, port, GM_GP_CTRL); + gma_write16(hw, port, GM_GP_CTRL, ctrl & ~GM_GPCR_RX_ENA); + + memcpy_toio(hw->regs + B2_MAC_1 + port*8, dev->dev_addr, ETH_ALEN); + memcpy_toio(hw->regs + B2_MAC_2 + port*8, dev->dev_addr, ETH_ALEN); + + if (netif_running(dev)) { + if (hw->chip_id == CHIP_ID_GENESIS) + xm_outaddr(hw, port, XM_SA, dev->dev_addr); + else { + gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr); + gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr); + } } - mutex_unlock(&hw->phy_mutex); + + gma_write16(hw, port, GM_GP_CTRL, ctrl); return 0; } -- cgit v1.2.3 From 8b902aea40544bc9e4de913b491dc3a3411fd5d0 Mon Sep 17 00:00:00 2001 From: Linsys Contractor Mithlesh Thukral Date: Tue, 13 Mar 2007 04:13:13 -0800 Subject: NetXen: Bug fix for Jumbo frames on XG card NetXen: Set the MTU for the right port depending upon the port number for XG cards. Signed-off by: Mithlesh Thukral Signed-off-by: Jeff Garzik --- drivers/net/netxen/netxen_nic_hw.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/net/netxen/netxen_nic_hw.c b/drivers/net/netxen/netxen_nic_hw.c index 1be55702557..6537574a9cd 100644 --- a/drivers/net/netxen/netxen_nic_hw.c +++ b/drivers/net/netxen/netxen_nic_hw.c @@ -822,7 +822,10 @@ int netxen_nic_set_mtu_xgb(struct netxen_port *port, int new_mtu) { struct netxen_adapter *adapter = port->adapter; new_mtu += NETXEN_NIU_HDRSIZE + NETXEN_NIU_TLRSIZE; - netxen_nic_write_w0(adapter, NETXEN_NIU_XGE_MAX_FRAME_SIZE, new_mtu); + if (port->portnum == 0) + netxen_nic_write_w0(adapter, NETXEN_NIU_XGE_MAX_FRAME_SIZE, new_mtu); + else if (port->portnum == 1) + netxen_nic_write_w0(adapter, NETXEN_NIU_XG1_MAX_FRAME_SIZE, new_mtu); return 0; } -- cgit v1.2.3 From b58ecad8d6ca83e97cd2928a439efb49267539dc Mon Sep 17 00:00:00 2001 From: Linsys Contractor Mithlesh Thukral Date: Tue, 13 Mar 2007 04:15:06 -0800 Subject: NetXen: Fix softlockup seen during hardware access NetXen: This will fix a softlock seen on some machines. The reason was too much time was spent waiting for hardware access to go through. Signed-off by: Mithlesh Thukral Signed-off-by: Jeff Garzik --- drivers/net/netxen/netxen_nic.h | 1 + drivers/net/netxen/netxen_nic_ethtool.c | 1 + drivers/net/netxen/netxen_nic_init.c | 11 +++++++++-- 3 files changed, 11 insertions(+), 2 deletions(-) diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index 81742e4e561..dd8ce35332f 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -232,6 +232,7 @@ enum { #define MPORT_SINGLE_FUNCTION_MODE 0x1111 extern unsigned long long netxen_dma_mask; +extern unsigned long last_schedule_time; /* * NetXen host-peg signal message structure diff --git a/drivers/net/netxen/netxen_nic_ethtool.c b/drivers/net/netxen/netxen_nic_ethtool.c index 986ef98db22..ee1b5a24cbe 100644 --- a/drivers/net/netxen/netxen_nic_ethtool.c +++ b/drivers/net/netxen/netxen_nic_ethtool.c @@ -462,6 +462,7 @@ netxen_nic_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom, } printk(KERN_INFO "%s: flash unlocked. \n", netxen_nic_driver_name); + last_schedule_time = jiffies; ret = netxen_flash_erase_secondary(adapter); if (ret != FLASH_SUCCESS) { printk(KERN_ERR "%s: Flash erase failed.\n", diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c index 586d32b676a..229aa1c4fb7 100644 --- a/drivers/net/netxen/netxen_nic_init.c +++ b/drivers/net/netxen/netxen_nic_init.c @@ -42,6 +42,8 @@ struct crb_addr_pair { u32 data; }; +unsigned long last_schedule_time; + #define NETXEN_MAX_CRB_XFORM 60 static unsigned int crb_addr_xform[NETXEN_MAX_CRB_XFORM]; #define NETXEN_ADDR_ERROR (0xffffffff) @@ -404,9 +406,14 @@ static inline int do_rom_fast_write(struct netxen_adapter *adapter, int addr, static inline int do_rom_fast_read(struct netxen_adapter *adapter, int addr, int *valp) { + if (jiffies > (last_schedule_time + (8 * HZ))) { + last_schedule_time = jiffies; + schedule(); + } + netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_ADDRESS, addr); netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_ABYTE_CNT, 3); - udelay(70); /* prevent bursting on CRB */ + udelay(100); /* prevent bursting on CRB */ netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_DUMMY_BYTE_CNT, 0); netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_INSTR_OPCODE, 0xb); if (netxen_wait_rom_done(adapter)) { @@ -415,7 +422,7 @@ do_rom_fast_read(struct netxen_adapter *adapter, int addr, int *valp) } /* reset abyte_cnt and dummy_byte_cnt */ netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_ABYTE_CNT, 0); - udelay(70); /* prevent bursting on CRB */ + udelay(100); /* prevent bursting on CRB */ netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_DUMMY_BYTE_CNT, 0); *valp = netxen_nic_reg_read(adapter, NETXEN_ROMUSB_ROM_RDATA); -- cgit v1.2.3 From 14fdd90ef2ec1878d6851ec4dd8d5abb2cef098c Mon Sep 17 00:00:00 2001 From: "broonie@sirena.org.uk" Date: Wed, 14 Mar 2007 19:49:13 +0000 Subject: natsemi: Consistently use interrupt enable/disable functions The natsemi drivers include functions for enabling and disabling interrupts from the chip but these are not used in all code paths. This patch changes the code paths that touch the interrupt enable register to use the functions. In all cases this adds an extra PCI read to post the operation but since none of these are in fast paths this shouldn't be too much of a problem. Signed-Off-By: Mark Brown Signed-off-by: Jeff Garzik --- drivers/net/natsemi.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/natsemi.c b/drivers/net/natsemi.c index c6172a77a6d..2888880df3b 100644 --- a/drivers/net/natsemi.c +++ b/drivers/net/natsemi.c @@ -1712,7 +1712,7 @@ static void init_registers(struct net_device *dev) /* Enable interrupts by setting the interrupt mask. */ writel(DEFAULT_INTR, ioaddr + IntrMask); - writel(1, ioaddr + IntrEnable); + natsemi_irq_enable(dev); writel(RxOn | TxOn, ioaddr + ChipCmd); writel(StatsClear, ioaddr + StatsCtrl); /* Clear Stats */ @@ -3071,7 +3071,7 @@ static void enable_wol_mode(struct net_device *dev, int enable_intr) * Could be used to send a netlink message. */ writel(WOLPkt | LinkChange, ioaddr + IntrMask); - writel(1, ioaddr + IntrEnable); + natsemi_irq_enable(dev); } } @@ -3202,7 +3202,7 @@ static int natsemi_suspend (struct pci_dev *pdev, pm_message_t state) disable_irq(dev->irq); spin_lock_irq(&np->lock); - writel(0, ioaddr + IntrEnable); + natsemi_irq_disable(dev); np->hands_off = 1; natsemi_stop_rxtx(dev); netif_stop_queue(dev); -- cgit v1.2.3 From 069f8256362b7a17da532f0631cee73b4cfee65b Mon Sep 17 00:00:00 2001 From: "broonie@sirena.org.uk" Date: Wed, 14 Mar 2007 19:49:14 +0000 Subject: natsemi: Fix NAPI for interrupt sharing The interrupt status register for the natsemi chips is clear on read and was read unconditionally from both the interrupt and from the NAPI poll routine, meaning that if the interrupt service routine was called (for example, due to a shared interrupt) while a NAPI poll was scheduled interrupts could be missed. This patch fixes that by ensuring that the interrupt status register is only read by the interrupt handler when interrupts are enabled from the chip. It also reverts a workaround for this problem from the netpoll hook and improves the trace for interrupt events. Thanks to Sergei Shtylyov for spotting the issue, Mark Huth for a simpler method and Simon Blake for testing resources. Signed-Off-By: Mark Brown Signed-off-by: Jeff Garzik --- drivers/net/natsemi.c | 38 ++++++++++++++++++++------------------ 1 file changed, 20 insertions(+), 18 deletions(-) diff --git a/drivers/net/natsemi.c b/drivers/net/natsemi.c index 2888880df3b..5f88200724e 100644 --- a/drivers/net/natsemi.c +++ b/drivers/net/natsemi.c @@ -2119,28 +2119,35 @@ static irqreturn_t intr_handler(int irq, void *dev_instance) struct netdev_private *np = netdev_priv(dev); void __iomem * ioaddr = ns_ioaddr(dev); - if (np->hands_off) + /* Reading IntrStatus automatically acknowledges so don't do + * that while interrupts are disabled, (for example, while a + * poll is scheduled). */ + if (np->hands_off || !readl(ioaddr + IntrEnable)) return IRQ_NONE; - /* Reading automatically acknowledges. */ np->intr_status = readl(ioaddr + IntrStatus); + if (!np->intr_status) + return IRQ_NONE; + if (netif_msg_intr(np)) printk(KERN_DEBUG "%s: Interrupt, status %#08x, mask %#08x.\n", dev->name, np->intr_status, readl(ioaddr + IntrMask)); - if (!np->intr_status) - return IRQ_NONE; - prefetch(&np->rx_skbuff[np->cur_rx % RX_RING_SIZE]); if (netif_rx_schedule_prep(dev)) { /* Disable interrupts and register for poll */ natsemi_irq_disable(dev); __netif_rx_schedule(dev); - } + } else + printk(KERN_WARNING + "%s: Ignoring interrupt, status %#08x, mask %#08x.\n", + dev->name, np->intr_status, + readl(ioaddr + IntrMask)); + return IRQ_HANDLED; } @@ -2156,6 +2163,12 @@ static int natsemi_poll(struct net_device *dev, int *budget) int work_done = 0; do { + if (netif_msg_intr(np)) + printk(KERN_DEBUG + "%s: Poll, status %#08x, mask %#08x.\n", + dev->name, np->intr_status, + readl(ioaddr + IntrMask)); + if (np->intr_status & (IntrTxDone | IntrTxIntr | IntrTxIdle | IntrTxErr)) { spin_lock(&np->lock); @@ -2399,19 +2412,8 @@ static struct net_device_stats *get_stats(struct net_device *dev) #ifdef CONFIG_NET_POLL_CONTROLLER static void natsemi_poll_controller(struct net_device *dev) { - struct netdev_private *np = netdev_priv(dev); - disable_irq(dev->irq); - - /* - * A real interrupt might have already reached us at this point - * but NAPI might still haven't called us back. As the interrupt - * status register is cleared by reading, we should prevent an - * interrupt loss in this case... - */ - if (!np->intr_status) - intr_handler(dev->irq, dev); - + intr_handler(dev->irq, dev); enable_irq(dev->irq); } #endif -- cgit v1.2.3 From d2a900365b8963d7ca46f05d8e7176d1be3cc71d Mon Sep 17 00:00:00 2001 From: "broonie@sirena.org.uk" Date: Wed, 14 Mar 2007 19:49:15 +0000 Subject: natsemi: Avoid IntrStatus lossage if RX state machine resets. This patch fixes the poll routine for the natsemi driver so that if the driver detects an RX state machine lockup then no interrupts will be lost while the driver recovers from that. Signed-Off-By: Mark Brown Signed-off-by: Jeff Garzik --- drivers/net/natsemi.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) diff --git a/drivers/net/natsemi.c b/drivers/net/natsemi.c index 5f88200724e..349b96a3ec4 100644 --- a/drivers/net/natsemi.c +++ b/drivers/net/natsemi.c @@ -2169,6 +2169,14 @@ static int natsemi_poll(struct net_device *dev, int *budget) dev->name, np->intr_status, readl(ioaddr + IntrMask)); + /* netdev_rx() may read IntrStatus again if the RX state + * machine falls over so do it first. */ + if (np->intr_status & + (IntrRxDone | IntrRxIntr | RxStatusFIFOOver | + IntrRxErr | IntrRxOverrun)) { + netdev_rx(dev, &work_done, work_to_do); + } + if (np->intr_status & (IntrTxDone | IntrTxIntr | IntrTxIdle | IntrTxErr)) { spin_lock(&np->lock); @@ -2180,12 +2188,6 @@ static int natsemi_poll(struct net_device *dev, int *budget) if (np->intr_status & IntrAbnormalSummary) netdev_error(dev, np->intr_status); - if (np->intr_status & - (IntrRxDone | IntrRxIntr | RxStatusFIFOOver | - IntrRxErr | IntrRxOverrun)) { - netdev_rx(dev, &work_done, work_to_do); - } - *budget -= work_done; dev->quota -= work_done; -- cgit v1.2.3