| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I2fcf46d1fc4b0cd4c61e5be3654c43b80db86015
|
|
commit 2efaca927f5cd7ecd0f1554b8f9b6a9a2c329c03 upstream.
I haven't reproduced it myself but the fail scenario is that on such
machines (notably ARM and some embedded powerpc), if you manage to hit
that futex path on a writable page whose dirty bit has gone from the PTE,
you'll livelock inside the kernel from what I can tell.
It will go in a loop of trying the atomic access, failing, trying gup to
"fix it up", getting succcess from gup, go back to the atomic access,
failing again because dirty wasn't fixed etc...
So I think you essentially hang in the kernel.
The scenario is probably rare'ish because affected architecture are
embedded and tend to not swap much (if at all) so we probably rarely hit
the case where dirty is missing or young is missing, but I think Shan has
a piece of SW that can reliably reproduce it using a shared writable
mapping & fork or something like that.
On archs who use SW tracking of dirty & young, a page without dirty is
effectively mapped read-only and a page without young unaccessible in the
PTE.
Additionally, some architectures might lazily flush the TLB when relaxing
write protection (by doing only a local flush), and expect a fault to
invalidate the stale entry if it's still present on another processor.
The futex code assumes that if the "in_atomic()" access -EFAULT's, it can
"fix it up" by causing get_user_pages() which would then be equivalent to
taking the fault.
However that isn't the case. get_user_pages() will not call
handle_mm_fault() in the case where the PTE seems to have the right
permissions, regardless of the dirty and young state. It will eventually
update those bits ... in the struct page, but not in the PTE.
Additionally, it will not handle the lazy TLB flushing that can be
required by some architectures in the fault case.
Basically, gup is the wrong interface for the job. The patch provides a
more appropriate one which boils down to just calling handle_mm_fault()
since what we are trying to do is simulate a real page fault.
The futex code currently attempts to write to user memory within a
pagefault disabled section, and if that fails, tries to fix it up using
get_user_pages().
This doesn't work on archs where the dirty and young bits are maintained
by software, since they will gate access permission in the TLB, and will
not be updated by gup().
In addition, there's an expectation on some archs that a spurious write
fault triggers a local TLB flush, and that is missing from the picture as
well.
I decided that adding those "features" to gup() would be too much for this
already too complex function, and instead added a new simpler
fixup_user_fault() which is essentially a wrapper around handle_mm_fault()
which the futex code can call.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix some nits Darren saw, fiddle comment layout]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Shan Hai <haishan.bai@gmail.com>
Tested-by: Shan Hai <haishan.bai@gmail.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Darren Hart <darren.hart@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change-Id: I84219e4262cc051c141432cd60ac15809251e132
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/35645
Tested-by: Per VAHLNE <per.xx.vahlne@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
commit 40ee4dffff061399eb9358e0c8fcfbaf8de4c8fe upstream.
The "enable" file for the event system can be removed when a module
is unloaded and the event system only has events from that module.
As the event system nr_events count goes to zero, it may be freed
if its ref_count is also set to zero.
Like the "filter" file, the "enable" file may be opened by a task and
referenced later, after a module has been unloaded and the events for
that event system have been removed.
Although the "filter" file referenced the event system structure,
the "enable" file only references a pointer to the event system
name. Since the name is freed when the event system is removed,
it is possible that an access to the "enable" file may reference
a freed pointer.
Update the "enable" file to use the subsystem_open() routine that
the "filter" file uses, to keep a reference to the event system
structure while the "enable" file is opened.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change-Id: I46951b3d423d7eee29dfee3abde606cb9c90520b
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/35639
Tested-by: Per VAHLNE <per.xx.vahlne@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
commit e9dbfae53eeb9fc3d4bb7da3df87fa9875f5da02 upstream.
The event system is freed when its nr_events is set to zero. This happens
when a module created an event system and then later the module is
removed. Modules may share systems, so the system is allocated when
it is created and freed when the modules are unloaded and all the
events under the system are removed (nr_events set to zero).
The problem arises when a task opened the "filter" file for the
system. If the module is unloaded and it removed the last event for
that system, the system structure is freed. If the task that opened
the filter file accesses the "filter" file after the system has
been freed, the system will access an invalid pointer.
By adding a ref_count, and using it to keep track of what
is using the event system, we can free it after all users
are finished with the event system.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change-Id: Ic38714d39f69b07444aa6c0684c7105637ae6535
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/35638
Tested-by: Per VAHLNE <per.xx.vahlne@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
The below patch is for -stable only, upstream has a much larger patch
that contains the below hunk in commit a8b0ca17b80e92faab46ee7179ba9e99ccb61233
Vince found that under certain circumstances software event overflows
go wrong and deadlock. Avoid trying to delete a timer from the timer
callback.
Reported-by: Vince Weaver <vweaver1@eecs.utk.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change-Id: Ieaf67882ae859ae744fa53da83f29e7ce38f96f9
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/35618
Tested-by: Per VAHLNE <per.xx.vahlne@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
The IRQ name has moved to the struct irqaction list (so print
first action's name).
Change-Id: I65a627457f9abaf7c1dcc32d8814243ba2ff4717
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/35552
Tested-by: Per VAHLNE <per.xx.vahlne@stericsson.com>
Reviewed-by: QABUILD
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
In order to save >100ms during resume, plugging and unplugging
the secondary cpus are done in separate threads instead
of in sequence with device suspend/resume calls.
ST-Ericsson Linux next: Not tested, ask SSM for ER
ST-Ericsson ID: ER356920
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: Ie2b28595e777b056e486ae6c3d90736bb274a307
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/34871
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
|
|
When using kexec/kdump without an crash kernel image loaded:
* clean the caches and write the crash_notes
* perform a restart
ST-Ericsson ID: 340331
Change-Id: I1ae34ed2b5e43da4849650a8a7d2f1e453dcbe93
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/32678
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
Change-Id: I1e3cf9a0e67c7941ec9a276678dcb61c01a2a957
|
|
..linux-linaro-3.0-2011.07-1_glk3.0
Conflicts:
arch/arm/common/Makefile
drivers/misc/Kconfig
drivers/misc/Makefile
kernel/printk.c
Change-Id: I126f34edb1879981909072beefb2738cad26f951
|
|
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
|
|
The default setting of 128 is not close to enough to save
all the names of processes/threads executed during 1s
of idle in Android.
ST-Ericsson Linux next: -
ST-Ericsson ID: -
ST-Ericsson FOSS-OUT ID: Trivial
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Change-Id: I6f9ef8d5f167f4b1f8de7b996130e65ee5fc7598
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/15157
Reviewed-by: Martin PERSSON <martin.persson@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
|
|
This patch will make the threaded nested handler run all the registered
shared action handlers and not just the first registered.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Change-Id: Ib484a2fa50186dbc05aedbcb9936518302ab801b
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/10494
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Change-Id: Ie73cf9782ccbf3a974383fa5d1474613c660c6b9
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/3172
Tested-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
|
|
Makes low-level printk work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
|
|
trace and scheduler wakeup/context switch tracing
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
|
|
When kexec'ing to u-boot only the crashing core is used (and will have
to be kicked by u-boot). The watchdog of other core has to be stopped
before leaving linux.
ST-Ericsson ID: -
Change-Id: I329630fd8040f8af3e54fc51aa7187217938f0b8
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/13678
Reviewed-by: QATOOLS
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
|
|
into linaro-3.0
|
|
when enabled, prints out the function of each handler as they are called
Change-Id: I5ed251867e0e3aa3cd05f030ff3579808cedd0c2
Signed-off-by: Erik Gilling <konkers@android.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
signal: align __lock_task_sighand() irq disabling and RCU
softirq,rcu: Inform RCU of irq_exit() activity
sched: Add irq_{enter,exit}() to scheduler_ipi()
rcu: protect __rcu_read_unlock() against scheduler-using irq handlers
rcu: Streamline code produced by __rcu_read_unlock()
rcu: Fix RCU_BOOST race handling current->rcu_read_unlock_special
rcu: decrease rcu_report_exp_rnp coupling with scheduler
|
|
Prints the time spent in suspend in the kernel log, and
keeps statistics on the time spent in suspend in
/sys/kernel/debug/suspend_time
Change-Id: Ia6b9ebe4baa0f7f5cd211c6a4f7e813aefd3fa1d
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-2.6-rcu into core/urgent
|
|
The __lock_task_sighand() function calls rcu_read_lock() with interrupts
and preemption enabled, but later calls rcu_read_unlock() with interrupts
disabled. It is therefore possible that this RCU read-side critical
section will be preempted and later RCU priority boosted, which means that
rcu_read_unlock() will call rt_mutex_unlock() in order to deboost itself, but
with interrupts disabled. This results in lockdep splats, so this commit
nests the RCU read-side critical section within the interrupt-disabled
region of code. This prevents the RCU read-side critical section from
being preempted, and thus prevents the attempt to deboost with interrupts
disabled.
It is quite possible that a better long-term fix is to make rt_mutex_unlock()
disable irqs when acquiring the rt_mutex structure's ->wait_lock.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The rcu_read_unlock_special() function relies on in_irq() to exclude
scheduler activity from interrupt level. This fails because exit_irq()
can invoke the scheduler after clearing the preempt_count() bits that
in_irq() uses to determine that it is at interrupt level. This situation
can result in failures as follows:
$task IRQ SoftIRQ
rcu_read_lock()
/* do stuff */
<preempt> |= UNLOCK_BLOCKED
rcu_read_unlock()
--t->rcu_read_lock_nesting
irq_enter();
/* do stuff, don't use RCU */
irq_exit();
sub_preempt_count(IRQ_EXIT_OFFSET);
invoke_softirq()
ttwu();
spin_lock_irq(&pi->lock)
rcu_read_lock();
/* do stuff */
rcu_read_unlock();
rcu_read_unlock_special()
rcu_report_exp_rnp()
ttwu()
spin_lock_irq(&pi->lock) /* deadlock */
rcu_read_unlock_special(t);
Ed can simply trigger this 'easy' because invoke_softirq() immediately
does a ttwu() of ksoftirqd/# instead of doing the in-place softirq stuff
first, but even without that the above happens.
Cure this by also excluding softirqs from the
rcu_read_unlock_special() handler and ensuring the force_irqthreads
ksoftirqd/# wakeup is done from full softirq context.
[ Alternatively, delaying the ->rcu_read_lock_nesting decrement
until after the special handling would make the thing more robust
in the face of interrupts as well. And there is a separate patch
for that. ]
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-and-tested-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Ensure scheduler_ipi() calls irq_{enter,exit} when it does some actual
work. Traditionally we never did any actual work from the resched IPI
and all magic happened in the return from interrupt path.
Now that we do do some work, we need to ensure irq_{enter,exit} are
called so that we don't confuse things.
This affects things like timekeeping, NO_HZ and RCU, basically
everything with a hook in irq_enter/exit.
Explicit examples of things going wrong are:
sched_clock_cpu() -- has a callback when leaving NO_HZ state to take
a new reading from GTOD and TSC. Without this
callback, time is stuck in the past.
RCU -- needs in_irq() to work in order to avoid some nasty deadlocks
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The addition of RCU read-side critical sections within runqueue and
priority-inheritance lock critical sections introduced some deadlock
cycles, for example, involving interrupts from __rcu_read_unlock()
where the interrupt handlers call wake_up(). This situation can cause
the instance of __rcu_read_unlock() invoked from interrupt to do some
of the processing that would otherwise have been carried out by the
task-level instance of __rcu_read_unlock(). When the interrupt-level
instance of __rcu_read_unlock() is called with a scheduler lock held
from interrupt-entry/exit situations where in_irq() returns false,
deadlock can result.
This commit resolves these deadlocks by using negative values of
the per-task ->rcu_read_lock_nesting counter to indicate that an
instance of __rcu_read_unlock() is in flight, which in turn prevents
instances from interrupt handlers from doing any special processing.
This patch is inspired by Steven Rostedt's earlier patch that similarly
made __rcu_read_unlock() guard against interrupt-mediated recursion
(see https://lkml.org/lkml/2011/7/15/326), but this commit refines
Steven's approach to avoid the need for preemption disabling on the
__rcu_read_unlock() fastpath and to also avoid the need for manipulating
a separate per-CPU variable.
This patch avoids need for preempt_disable() by instead using negative
values of the per-task ->rcu_read_lock_nesting counter. Note that nested
rcu_read_lock()/rcu_read_unlock() pairs are still permitted, but they will
never see ->rcu_read_lock_nesting go to zero, and will therefore never
invoke rcu_read_unlock_special(), thus preventing them from seeing the
RCU_READ_UNLOCK_BLOCKED bit should it be set in ->rcu_read_unlock_special.
This patch also adds a check for ->rcu_read_unlock_special being negative
in rcu_check_callbacks(), thus preventing the RCU_READ_UNLOCK_NEED_QS
bit from being set should a scheduling-clock interrupt occur while
__rcu_read_unlock() is exiting from an outermost RCU read-side critical
section.
Of course, __rcu_read_unlock() can be preempted during the time that
->rcu_read_lock_nesting is negative. This could result in the setting
of the RCU_READ_UNLOCK_BLOCKED bit after __rcu_read_unlock() checks it,
and would also result it this task being queued on the corresponding
rcu_node structure's blkd_tasks list. Therefore, some later RCU read-side
critical section would enter rcu_read_unlock_special() to clean up --
which could result in deadlock if that critical section happened to be in
the scheduler where the runqueue or priority-inheritance locks were held.
This situation is dealt with by making rcu_preempt_note_context_switch()
check for negative ->rcu_read_lock_nesting, thus refraining from
queuing the task (and from setting RCU_READ_UNLOCK_BLOCKED) if we are
already exiting from the outermost RCU read-side critical section (in
other words, we really are no longer actually in that RCU read-side
critical section). In addition, rcu_preempt_note_context_switch()
invokes rcu_read_unlock_special() to carry out the cleanup in this case,
which clears out the ->rcu_read_unlock_special bits and dequeues the task
(if necessary), in turn avoiding needless delay of the current RCU grace
period and needless RCU priority boosting.
It is still illegal to call rcu_read_unlock() while holding a scheduler
lock if the prior RCU read-side critical section has ever had either
preemption or irqs enabled. However, the common use case is legal,
namely where then entire RCU read-side critical section executes with
irqs disabled, for example, when the scheduler lock is held across the
entire lifetime of the RCU read-side critical section.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
When creating sched_domains, stop when we've covered the entire
target span instead of continuing to create domains, only to
later find they're redundant and throw them away again.
This avoids single node systems from touching funny NUMA
sched_domain creation code and reduces the risks of the new
SD_OVERLAP code.
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Anton Blanchard <anton@samba.org>
Cc: mahesh@linux.vnet.ibm.com
Cc: benh@kernel.crashing.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1311180177.29152.57.camel@twins
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Allow for sched_domain spans that overlap by giving such domains their
own sched_group list instead of sharing the sched_groups amongst
each-other.
This is needed for machines with more than 16 nodes, because
sched_domain_node_span() will generate a node mask from the
16 nearest nodes without regard if these masks have any overlap.
Currently sched_domains have a sched_group that maps to their child
sched_domain span, and since there is no overlap we share the
sched_group between the sched_domains of the various CPUs. If however
there is overlap, we would need to link the sched_group list in
different ways for each cpu, and hence sharing isn't possible.
In order to solve this, allocate private sched_groups for each CPU's
sched_domain but have the sched_groups share a sched_group_power
structure such that we can uniquely track the power.
Reported-and-tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-08bxqw9wis3qti9u5inifh3y@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In order to prepare for non-unique sched_groups per domain, we need to
carry the cpu_power elsewhere, so put a level of indirection in.
Reported-and-tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-qkho2byuhe4482fuknss40ad@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Given some common flag combinations, particularly -Os, gcc will inline
rcu_read_unlock_special() despite its being in an unlikely() clause.
Use noinline to prohibit this misoptimization.
In addition, move the second barrier() in __rcu_read_unlock() so that
it is not on the common-case code path. This will allow the compiler to
generate better code for the common-case path through __rcu_read_unlock().
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
|
|
The RCU_BOOST commits for TREE_PREEMPT_RCU introduced an other-task
write to a new RCU_READ_UNLOCK_BOOSTED bit in the task_struct structure's
->rcu_read_unlock_special field, but, as noted by Steven Rostedt, without
correctly synchronizing all accesses to ->rcu_read_unlock_special.
This could result in bits in ->rcu_read_unlock_special being spuriously
set and cleared due to conflicting accesses, which in turn could result
in deadlocks between the rcu_node structure's ->lock and the scheduler's
rq and pi locks. These deadlocks would result from RCU incorrectly
believing that the just-ended RCU read-side critical section had been
preempted and/or boosted. If that RCU read-side critical section was
executed with either rq or pi locks held, RCU's ensuing (incorrect)
calls to the scheduler would cause the scheduler to attempt to once
again acquire the rq and pi locks, resulting in deadlock. More complex
deadlock cycles are also possible, involving multiple rq and pi locks
as well as locks from multiple rcu_node structures.
This commit fixes synchronization by creating ->rcu_boosted field in
task_struct that is accessed and modified only when holding the ->lock
in the rcu_node structure on which the task is queued (on that rcu_node
structure's ->blkd_tasks list). This results in tasks accessing only
their own current->rcu_read_unlock_special fields, making unsynchronized
access once again legal, and keeping the rcu_read_unlock() fastpath free
of atomic instructions and memory barriers.
The reason that the rcu_read_unlock() fastpath does not need to access
the new current->rcu_boosted field is that this new field cannot
be non-zero unless the RCU_READ_UNLOCK_BLOCKED bit is set in the
current->rcu_read_unlock_special field. Therefore, rcu_read_unlock()
need only test current->rcu_read_unlock_special: if that is zero, then
current->rcu_boosted must also be zero.
This bug does not affect TINY_PREEMPT_RCU because this implementation
of RCU accesses current->rcu_read_unlock_special with irqs disabled,
thus preventing races on the !SMP systems that TINY_PREEMPT_RCU runs on.
Maybe-reported-by: Dave Jones <davej@redhat.com>
Maybe-reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
|
|
PREEMPT_RCU read-side critical sections blocking an expedited grace
period invoke rcu_report_exp_rnp(). When the last such critical section
has completed, rcu_report_exp_rnp() invokes the scheduler to wake up the
task that invoked synchronize_rcu_expedited() -- needlessly holding the
root rcu_node structure's lock while doing so, thus needlessly providing
a way for RCU and the scheduler to deadlock.
This commit therefore releases the root rcu_node structure's lock before
calling wake_up().
Reported-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
irq_domain_generate_simple() is an easy way to generate an irq translation
domain for simple irq controllers. It assumes a flat 1:1 mapping from
hardware irq number to an offset of the first linux irq number assigned
to the controller
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs. This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller. irq_domain
supports device tree translation for any number of interrupt
controllers.
This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation. x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet. On ARM it works and is required for much of the new
ARM device tree board support.
PowerPC has /not/ been converted to use this new infrastructure. It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details). Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.
SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Move the x86_64 idle notifiers originally by Andi Kleen and Venkatesh
Pallipadi to generic.
Change-Id: Idf29cda15be151f494ff245933c12462643388d5
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-2.6-rcu
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-2.6-rcu:
rcu: Prevent RCU callbacks from executing before scheduler initialized
|
|
Commit 3fe1698b7fe0 ("sched: Deal with non-atomic min_vruntime reads
on 32bit") forgot to initialize min_vruntime_copy which could lead to
an infinite while loop in task_waking_fair() under some circumstances
(early boot, lucky timing).
[ This bug was also reported by others that blamed it on the RCU
initialization problems ]
Reported-and-tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Under some rare but real combinations of configuration parameters, RCU
callbacks are posted during early boot that use kernel facilities that
are not yet initialized. Therefore, when these callbacks are invoked,
hard hangs and crashes ensue. This commit therefore prevents RCU
callbacks from being invoked until after the scheduler is fully up and
running, as in after multiple tasks have been spawned.
It might well turn out that a better approach is to identify the specific
RCU callbacks that are causing this problem, but that discussion will
wait until such time as someone really needs an RCU callback to be invoked
(as opposed to merely registered) during early boot.
Reported-by: julie Sullivan <kernelmail.jms@gmail.com>
Reported-by: RKK <kulkarni.ravi4@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: julie Sullivan <kernelmail.jms@gmail.com>
Tested-by: RKK <kulkarni.ravi4@gmail.com>
|
|
Rather than using explicit euid == 0 checks when trying to move
tasks into a cgroup via CFS, move permission checks into each
specific cgroup subsystem. If a subsystem does not specify a
'allow_attach' handler, then we fall back to doing our checks
the old way.
Use the 'allow_attach' handler for the 'cpu' cgroup to allow
non-root processes to add arbitrary processes to a 'cpu' cgroup
if it has the CAP_SYS_NICE capability set.
This version of the patch adds a 'allow_attach' handler instead
of reusing the 'can_attach' handler. If the 'can_attach' handler
is reused, a new cgroup that implements 'can_attach' but not
the permission checks could end up with no permission checks
at all.
Change-Id: Icfa950aa9321d1ceba362061d32dc7dfa2c64f0c
Original-Author: San Mehat <san@google.com>
Signed-off-by: Colin Cross <ccross@android.com>
|
|
This reverts commit 1d38bc7d0523af2233b4280e2aeab34c6a076665.
Change-Id: I2c5066b696cbdd5ca117ed74718bcb7e70e878e7
Signed-off-by: Colin Cross <ccross@android.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
pcmcia: pxa2xx/vpac270: free gpios on exist rather than requesting
ARM: pxa/raumfeld: fix device name for codec ak4104
ARM: pxa/raumfeld: display initialisation fixes
ARM: pxa/raumfeld: adapt to upcoming hardware change
ARM: pxa: fix gpio_to_chip() clash with gpiolib namespace
genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
arm: mach-vt8500: add forgotten irq_data conversion
ARM: pxa168: correct nand pmu setting
ARM: pxa910: correct nand pmu setting
ARM: pxa: fix PGSR register address calculation
|
|
This was legacy code brought over from the RT tree and
is no longer necessary.
Signed-off-by: Dima Zavin <dima@android.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Walker <dwalker@codeaurora.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/1310084879-10351-2-git-send-email-dima@android.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Hibernate: Fix free_unnecessary_pages()
|
|
'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: Fix boot crash when kmemleak and debugobjects enabled
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
jump_label: Fix jump_label update for modules
oprofile, x86: Fix race in nmi handler while starting counters
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Disable (revert) SCHED_LOAD_SCALE increase
sched, cgroups: Fix MIN_SHARES on 64-bit boxen
|
|
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There is a bug in free_unnecessary_pages() that causes it to
attempt to free too many pages in some cases, which triggers the
BUG_ON() in memory_bm_clear_bit() for copy_bm. Namely, if
count_data_pages() is initially greater than alloc_normal, we get
to_free_normal equal to 0 and "save" greater from 0. In that case,
if the sum of "save" and count_highmem_pages() is greater than
alloc_highmem, we subtract a positive number from to_free_normal.
Hence, since to_free_normal was 0 before the subtraction and is
an unsigned int, the result is converted to a huge positive number
that is used as the number of pages to free.
Fix this bug by checking if to_free_normal is actually greater
than or equal to the number we're going to subtract from it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@kernel.org
|
|
Provides the ability to resize a resource that is already allocated.
This functionality is put in place to support reallocation needs of
pci resources.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit c8b28116 ("sched: Increase SCHED_LOAD_SCALE resolution")
intended to have no user-visible effect, but allows setting
cpu.shares to < MIN_SHARES, which the user then sees.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nikhil Rao <ncrao@google.com>
Link: http://lkml.kernel.org/r/1307192600.8618.3.camel@marge.simson.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
