summaryrefslogtreecommitdiff
path: root/net
AgeCommit message (Collapse)Author
2011-10-13cw1200: Purge cfg80211 beacon cache before authentication.Dmitry Tarnyagin
cw1200 device requires SSID to be available at AUTH stage. cfg80211 beacon cache is designed to handle multi-SSID BSSes, so bss struct returned by cfg80211_get_bss() has random SSID if BSS just changed SSID before authentication (typical for p2p). This is a firmware design fault, however as a workaround cfg80211 beacon cache is purged to make sure target BSS is searchable in rb-tree at the AUTH stage. Likely will not be accepted by community. Change-Id: I38d071e0d32bf414906170a19134718b0e834cce Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/28558 Tested-by: Dmitry TARNYAGIN <dmitry.tarnyagin@stericsson.com> Reviewed-by: Bartosz MARKOWSKI <bartosz.markowski@tieto.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/28696 Tested-by: Bartosz MARKOWSKI <bartosz.markowski@tieto.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/33504 Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
2011-10-12wireless-next: WAPI support for hardware-accelerated driversJanusz Dziedzic
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/24551 Tested-by: Janusz DZIEDZIC <janusz.dziedzic@tieto.com> Reviewed-by: Janusz DZIEDZIC <janusz.dziedzic@tieto.com> Change-Id: I0300854865f8de07413164fd4461a9c8aae5dff3 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/26976 Reviewed-by: Bartosz MARKOWSKI <bartosz.markowski@tieto.com> Tested-by: Bartosz MARKOWSKI <bartosz.markowski@tieto.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/33473 Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
2011-10-05Revert "WLAN: Add symlink to compat-wireless"Robert Marklund
This reverts commit 7af327e4265826a1373a6281aa9b343e78d90ce1.
2011-10-05CAIF : coverity issuesDurga Prasada Rao BATHINA
free phy_driver memory and initialize linkid to 0. ST-Ericsson ID: 358047 ST-Ericsson Linux next: NA ST-Ericsson FOSS-OUT ID: NA Change-Id: Icb295648b23bd836b9f5a40a0b605e4792a8511d Signed-off-by: Durga Prasada Rao BATHINA <durgaprasadarao.b@stericcson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/31751 Reviewed-by: Bibek BASU <bibek.basu@stericsson.com> Tested-by: Bibek BASU <bibek.basu@stericsson.com>
2011-10-05Phonet: Insert correct dest addr and port for TCP/IP data on U8500Hemant Ramdasi
Inserts correct dest addr and port for the TCP/IP data on ST-Ericsson U8500. This is required due to lack of Pipe controller implementation in ST-Ericsson U8500 Modem Signed-off-by: Hemant Ramdasi <hemant.ramdasi@stericsson.com> Change-Id: I3c199cc94da3b81de3ab97f22b6e7087b2cd0071 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/31273
2011-10-05Revert "caif: Bugfix use for_each_safe when removing list nodes."Hemant Ramdasi
This reverts commit 8b7b286d853032b485de9753c3908c300266c660. Refer 0c184ed9032c58b21f0d90de28c796874b73d6a1 for original commit. Signed-off-by: Hemant Ramdasi <hemant.ramdasi@stericsson.com> Change-Id: Iaa8c88ed05d24bdfb3c7b505cc1342c088cdfd51 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/30328 Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
2011-10-05bluetooth: Add SCO parameters support for socketAndrzej Kaczmarek
Adds ability to setup SCO connection parameters through socket option. ST-Ericsson Linux next: Not tested, ER 256277 ST-Ericsson ID: 256277 ST-Ericsson FOSS-OUT ID: STETL-FOSS-OUT-10137 Change-Id: If859341019fd9f7cc7c0efe95750779e84fac801 Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/30136 Reviewed-by: Par-Gunnar HJALMDAHL <par-gunnar.p.hjalmdahl@stericsson.com> Tested-by: Par-Gunnar HJALMDAHL <par-gunnar.p.hjalmdahl@stericsson.com> Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com> Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
2011-10-05WLAN: Add symlink to compat-wirelessBartosz Markowski
And disable use of wireless from kernel tree if compat-wireless is enabled. Depends-On: I7147b541419c684dc337e5d32b021b470dd0f344, Ib489e754a7cf4bd79ce20955be61cae7958043e1, Id8d0913143e58a21dbfebe187a9594a0cb7bea8a, Ieaadb213c53d967ab5dcb293aeee088fd3efbae8, Ie280d1b7e533d7045e4e77c0cab3d69f1180c091, Ia40a0c011f35c3056d02d12b054f93aa86d99b47, Ib3b5524ec3814b00a7e46f591d7715db16eec5fd ST-Ericsson Linux next: - ST-Ericsson ID: CR283174 ST-Ericsson FOSS-OUT ID: Trivial Change-Id: I28a1b6b32383e71f9679031bffcefff022eaadde Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16241 Tested-by: Mariusz CZAPLICKI <mariusz.czaplicki@tieto.com> Reviewed-by: Bartosz MARKOWSKI <bartosz.markowski@tieto.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/30002 Tested-by: Bartosz MARKOWSKI <bartosz.markowski@tieto.com>
2011-10-05bluetooth: Improve BNEP extension headers handlingAndrzej Kaczmarek
Adds handling of extension headers to BNEP control packets. Adds support for BNEP setup connection request handled in pand. ST-Ericsson Linux next: - ST-Ericsson ID: 328144 ST-Ericsson FOSS-OUT-ID: Trivial Depends-On: Id2cbd106af9b380f63d87ea0b4652ec6cd996fa4 Change-Id: I005e00e2fe934dc19f40533953d5b233676f0d0e Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/18117 Reviewed-by: Par-Gunnar HJALMDAHL <par-gunnar.p.hjalmdahl@stericsson.com> Reviewed-by: Lukasz RYMANOWSKI <lukasz.rymanowski@stericsson.com> Reviewed-by: Henrik POSSUNG <henrik.possung@stericsson.com>
2011-10-05caif: Bugfix use for_each_safe when removing list nodes.Sjur Brændeland
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Change-Id: I7fec5eb6d17e01a87e89c2e7adec72d2f8babf83 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/21520 Reviewed-by: Erwan BRACQ <erwan.bracq@stericsson.com> Tested-by: Erwan BRACQ <erwan.bracq@stericsson.com> Reviewed-by: QATEST Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
2011-07-19Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: ceph: fix file mode calculation
2011-07-19ceph: fix file mode calculationSage Weil
open(2) must always include one of O_RDONLY, O_WRONLY, or O_RDWR. No need for any O_APPEND special case. Passing O_WRONLY|O_RDWR is undefined according to the man page, but the Linux VFS interprets this as O_RDWR, so we'll do the same. This fixes open(2) with flags O_RDWR|O_APPEND, which was incorrectly being translated to readonly. Reported-by: Fyodor Ustinov <ufm@ufm.su> Signed-off-by: Sage Weil <sage@newdream.net>
2011-07-16Bluetooth: Fix crash with incoming L2CAP connectionsIlia Kolomisnky
Another regression fix considering incomming l2cap connections with defer_setup enabled. In situations when incomming connection is extracted with l2cap_sock_accept, it's bt_sock info will have 'parent' member zerroed, but 'parent' may be used unconditionally in l2cap_conn_start() and l2cap_security_cfm() when defer_setup is enabled. Backtrace: [<bf02d5ac>] (l2cap_security_cfm+0x0/0x2ac [bluetooth]) from [<bf01f01c>] (hci_event_pac ket+0xc2c/0x4aa4 [bluetooth]) [<bf01e3f0>] (hci_event_packet+0x0/0x4aa4 [bluetooth]) from [<bf01a844>] (hci_rx_task+0x cc/0x27c [bluetooth]) [<bf01a778>] (hci_rx_task+0x0/0x27c [bluetooth]) from [<c008eee4>] (tasklet_action+0xa0/ 0x15c) [<c008ee44>] (tasklet_action+0x0/0x15c) from [<c008f38c>] (__do_softirq+0x98/0x130) r7:00000101 r6:00000018 r5:00000001 r4:efc46000 [<c008f2f4>] (__do_softirq+0x0/0x130) from [<c008f524>] (do_softirq+0x4c/0x58) [<c008f4d8>] (do_softirq+0x0/0x58) from [<c008f5e0>] (run_ksoftirqd+0xb0/0x1b4) r4:efc46000 r3:00000001 [<c008f530>] (run_ksoftirqd+0x0/0x1b4) from [<c009f2a8>] (kthread+0x84/0x8c) r7:00000000 r6:c008f530 r5:efc47fc4 r4:efc41f08 [<c009f224>] (kthread+0x0/0x8c) from [<c008cc84>] (do_exit+0x0/0x5f0) Signed-off-by: Ilia Kolomisnky <iliak@ti.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-16Bluetooth: Fix regression in L2CAP connection procedureGustavo F. Padovan
Caused by the following commit, partially revert it. commit 9fa7e4f76f3658ba1f44fbdb95c77e7df3f53f95 Author: Gustavo F. Padovan <padovan@profusion.mobi> Date: Thu Jun 30 16:11:30 2011 -0300 Bluetooth: Fix regression with incoming L2CAP connections PTS test A2DP/SRC/SRC_SET/TC_SRC_SET_BV_02_I revealed that ( probably after the df3c3931e commit ) the l2cap connection could not be established in case when the "Auth Complete" HCI event does not arive before the initiator send "Configuration request", in which case l2cap replies with "Command rejected" since the channel is still in BT_CONNECT2 state. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-14net: remove NETIF_F_ALL_TX_OFFLOADSMichał Mirosław
There is no software fallback implemented for SCTP or FCoE checksumming, and so it should not be passed on by software devices like bridge or bonding. For VLAN devices, this is different. First, the driver for underlying device should be prepared to get offloaded packets even when the feature is disabled (especially if it advertises it in vlan_features). Second, devices under VLANs do not get replaced without tearing down the VLAN first. This fixes a mess I accidentally introduced while converting bonding to ndo_fix_features. NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they are unused as of commit 712ae51afd. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-14net: sctp: fix checksum marking for outgoing packetsMichał Mirosław
Packets to devices without NETIF_F_SCTP_CSUM (including NETIF_F_NO_CSUM) should be properly checksummed because the packets can be diverted or rerouted after construction. This still leaves packets diverted from NETIF_F_SCTP_CSUM-enabled devices with broken checksums. Fixing this needs implementing software offload fallback in networking core. For users of sctp_checksum_disable, skb->ip_summed should be left as CHECKSUM_NONE and not CHECKSUM_UNNECESSARY as per include/linux/skbuff.h. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-13Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6Linus Torvalds
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: SUNRPC: Fix use of static variable in rpcb_getport_async NFSv4.1: update nfs4_fattr_bitmap_maxsz SUNRPC: Fix a race between work-queue and rpc_killall_tasks pnfs: write: Set mds_offset in the generic layer - it is needed by all LDs
2011-07-12SUNRPC: Fix use of static variable in rpcb_getport_asyncBen Greear
Because struct rpcbind_args *map was declared static, if two threads entered this method at the same time, the values assigned to map could be sent two two differen tasks. This could cause all sorts of problems, include use-after-free and double-free of memory. Fix this by removing the static declaration so that the map pointer is on the stack. Signed-off-by: Ben Greear <greearb@candelatech.com> Cc: stable@kernel.org Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2011-07-08sctp: ABORT if receive, reassmbly, or reodering queue is not empty while ↵Thomas Graf
closing socket Trigger user ABORT if application closes a socket which has data queued on the socket receive queue or chunks waiting on the reassembly or ordering queue as this would imply data being lost which defeats the point of a graceful shutdown. This behavior is already practiced in TCP. We do not check the input queue because that would mean to parse all chunks on it to look for unacknowledged data which seems too much of an effort. Control chunks or duplicated chunks may also be in the input queue and should not be stopping a graceful shutdown. Signed-off-by: Thomas Graf <tgraf@infradead.org> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2011-07-08XFRM: Fix memory leak in xfrm_state_updateTushar Gohad
Upon "ip xfrm state update ..", xfrm_add_sa() takes an extra reference on the user-supplied SA and forgets to drop the reference when xfrm_state_update() returns 0. This leads to a memory leak as the parameter SA is never freed. This change attempts to fix the leak by calling __xfrm_state_put() when xfrm_state_update() updates a valid SA (err = 0). The parameter SA is added to the gc list when the final reference is dropped by xfrm_add_sa() upon completion. Signed-off-by: Tushar Gohad <tgohad@mvista.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into for-davem
2011-07-07SUNRPC: Fix a race between work-queue and rpc_killall_tasksTrond Myklebust
Since rpc_killall_tasks may modify the rpc_task's tk_action field without any locking, we need to be careful when dereferencing it. Reported-by: Ben Greear <greearb@candelatech.com> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: stable@kernel.org
2011-07-07sctp: Enforce retransmission limit during shutdownThomas Graf
When initiating a graceful shutdown while having data chunks on the retransmission queue with a peer which is in zero window mode the shutdown is never completed because the retransmission error count is reset periodically by the following two rules: - Do not timeout association while doing zero window probe. - Reset overall error count when a heartbeat request has been acknowledged. The graceful shutdown will wait for all outstanding TSN to be acknowledged before sending the SHUTDOWN request. This never happens due to the peer's zero window not acknowledging the continuously retransmitted data chunks. Although the error counter is incremented for each failed retransmission, the receiving of the SACK announcing the zero window clears the error count again immediately. Also heartbeat requests continue to be sent periodically. The peer acknowledges these requests causing the error counter to be reset as well. This patch changes behaviour to only reset the overall error counter for the above rules while not in shutdown. After reaching the maximum number of retransmission attempts, the T5 shutdown guard timer is scheduled to give the receiver some additional time to recover. The timer is stopped as soon as the receiver acknowledges any data. The issue can be easily reproduced by establishing a sctp association over the loopback device, constantly queueing data at the sender while not reading any at the receiver. Wait for the window to reach zero, then initiate a shutdown by killing both processes simultaneously. The association will never be freed and the chunks on the retransmission queue will be retransmitted indefinitely. Signed-off-by: Thomas Graf <tgraf@infradead.org> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits) sctp: fix missing send up SCTP_SENDER_DRY_EVENT when subscribe it net: refine {udp|tcp|sctp}_mem limits vmxnet3: round down # of queues to power of two net: sh_eth: fix the parameter for the ETHER of SH7757 net: sh_eth: fix cannot work half-duplex mode net: vlan: enable soft features regardless of underlying device vmxnet3: fix starving rx ring whenoc_skb kb fails bridge: Always flood broadcast packets greth: greth_set_mac_add would corrupt the MAC address. net: bind() fix error return on wrong address family natsemi: silence dma-debug warnings net: 8139too: Initial necessary vlan_features to support vlan Fix call trace when interrupts are disabled while sleeping function kzalloc is called qlge:Version change to v1.00.00.29 qlge: Fix printk priority so chip fatal errors are always reported. qlge:Fix crash caused by mailbox execution on wedged chip. xfrm4: Don't call icmp_send on local error ipv4: Don't use ufo handling on later transformed packets xfrm: Remove family arg from xfrm_bundle_ok ipv6: Don't put artificial limit on routing table size. ...
2011-07-07mac80211: fix TKIP replay vulnerabilityJohannes Berg
Unlike CCMP, the presence or absence of the QoS field doesn't change the encryption, only the TID is used. When no QoS field is present, zero is used as the TID value. This means that it is possible for an attacker to take a QoS packet with TID 0 and replay it as a non-QoS packet. Unfortunately, mac80211 uses different IVs for checking the validity of the packet's TKIP IV when it checks TID 0 and when it checks non-QoS packets. This means it is vulnerable to this replay attack. To fix this, use the same replay counter for TID 0 and non-QoS packets by overriding the rx->queue value to 0 if it is 16 (non-QoS). This is a minimal fix for now. I caused this issue in commit 1411f9b531f0a910cd1c85a337737c1e6ffbae6a Author: Johannes Berg <johannes@sipsolutions.net> Date: Thu Jul 10 10:11:02 2008 +0200 mac80211: fix RX sequence number check while fixing a sequence number issue (there, a separate counter needs to be used). Cc: stable@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07mac80211: fix ie memory allocation for scheduled scansLuciano Coelho
We were not allocating memory for the IEs passed in the scheduled_scan request and this was causing memory corruption (buffer overflow). Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07sctp: fix missing send up SCTP_SENDER_DRY_EVENT when subscribe itWei Yongjun
We forgot to send up SCTP_SENDER_DRY_EVENT notification when user app subscribes to this event, and there is no data to be sent or retransmit. This is required by the Socket API and used by the DTLS/SCTP implementation. Reported-by: Michael Tüxen <Michael.Tuexen@lurchi.franken.de> Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Tested-by: Robin Seggelmann <seggelmann@fh-muenster.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07net: refine {udp|tcp|sctp}_mem limitsEric Dumazet
Current tcp/udp/sctp global memory limits are not taking into account hugepages allocations, and allow 50% of ram to be used by buffers of a single protocol [ not counting space used by sockets / inodes ...] Lets use nr_free_buffer_pages() and allow a default of 1/8 of kernel ram per protocol, and a minimum of 128 pages. Heavy duty machines sysadmins probably need to tweak limits anyway. References: https://bugzilla.stlinux.com/show_bug.cgi?id=38032 Reported-by: starlight <starlight@binnacle.cx> Suggested-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-05net: vlan: enable soft features regardless of underlying deviceShan Wei
If gso/gro feature of underlying device is turned off， then new created vlan device never can turn gso/gro on. Although underlying device don't support TSO, we still should use software segments for vlan device. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-05bridge: Always flood broadcast packetsHerbert Xu
As is_multicast_ether_addr returns true on broadcast packets as well, we need to explicitly exclude broadcast packets so that they're always flooded. This wasn't an issue before as broadcast packets were considered to be an unregistered multicast group, which were always flooded. However, as we now only flood such packets to router ports, this is no longer acceptable. Reported-by: Michael Guntsche <mike@it-loops.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-05Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: ceph: fix sync and dio writes across stripe boundaries libceph: fix page calculation for non-page-aligned io ceph: fix page alignment corrections
2011-07-05cfg80211: fix deadlock with rfkill/sched_scan by adding new mutexLuciano Coelho
There was a deadlock when rfkill-blocking a wireless interface, because we were locking the rdev mutex on NETDEV_GOING_DOWN to stop sched_scans that were eventually running. The rfkill block code was already holding a mutex under rdev: kernel: ======================================================= kernel: [ INFO: possible circular locking dependency detected ] kernel: 3.0.0-rc1-00049-g1fa7b6a #57 kernel: ------------------------------------------------------- kernel: kworker/0:1/4525 is trying to acquire lock: kernel: (&rdev->mtx){+.+.+.}, at: [<ffffffff8164c831>] cfg80211_netdev_notifier_call+0x131/0x5b0 kernel: kernel: but task is already holding lock: kernel: (&rdev->devlist_mtx){+.+.+.}, at: [<ffffffff8164dcef>] cfg80211_rfkill_set_block+0x4f/0xa0 kernel: kernel: which lock already depends on the new lock. To fix this, add a new mutex specifically for sched_scan, to protect the sched_scan_req element in the rdev struct, instead of using the global rdev mutex. Reported-by: Duane Griffin <duaneg@dghda.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-05Merge branch 'master' of ↵John W. Linville
master.kernel.org:/pub/scm/linux/kernel/git/padovan/bluetooth-2.6
2011-07-04net: bind() fix error return on wrong address familyMarcus Meissner
Hi, Reinhard Max also pointed out that the error should EAFNOSUPPORT according to POSIX. The Linux manpages have it as EINVAL, some other OSes (Minix, HPUX, perhaps BSD) use EAFNOSUPPORT. Windows uses WSAEFAULT according to MSDN. Other protocols error values in their af bind() methods in current mainline git as far as a brief look shows: EAFNOSUPPORT: atm, appletalk, l2tp, llc, phonet, rxrpc EINVAL: ax25, bluetooth, decnet, econet, ieee802154, iucv, netlink, netrom, packet, rds, rose, unix, x25, No check?: can/raw, ipv6/raw, irda, l2tp/l2tp_ip Ciao, Marcus Signed-off-by: Marcus Meissner <meissner@suse.de> Cc: Reinhard Max <max@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-01xfrm4: Don't call icmp_send on local errorSteffen Klassert
Calling icmp_send() on a local message size error leads to an incorrect update of the path mtu. So use ip_local_error() instead to notify the socket about the error. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-01ipv4: Don't use ufo handling on later transformed packetsSteffen Klassert
We might call ip_ufo_append_data() for packets that will be IPsec transformed later. This function should be used just for real udp packets. So we check for rt->dst.header_len which is only nonzero on IPsec handling and call ip_ufo_append_data() just if rt->dst.header_len is zero. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-01xfrm: Remove family arg from xfrm_bundle_okSteffen Klassert
The family arg is not used any more, so remove it. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-01ipv6: Don't put artificial limit on routing table size.David S. Miller
IPV6, unlike IPV4, doesn't have a routing cache. Routing table entries, as well as clones made in response to route lookup requests, all live in the same table. And all of these things are together collected in the destination cache table for ipv6. This means that routing table entries count against the garbage collection limits, even though such entries cannot ever be reclaimed and are added explicitly by the administrator (rather than being created in response to lookups). Therefore it makes no sense to count ipv6 routing table entries against the GC limits. Add a DST_NOCOUNT destination cache entry flag, and skip the counting if it is set. Use this flag bit in ipv6 when adding routing table entries. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-01ipv6: Don't change dst->flags using assignments.David S. Miller
This blows away any flags already set in the entry. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-01Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2011-06-30Bluetooth: Fix memory leak under page timeoutsTomas Targownik
If the remote device is not present, the connections attemp fails and the struct hci_conn was not freed Signed-off-by: Tomas Targownik <ttargownik@geicp.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-06-30Bluetooth: Fix regression with incoming L2CAP connectionsGustavo F. Padovan
PTS test A2DP/SRC/SRC_SET/TC_SRC_SET_BV_02_I revealed that ( probably after the df3c3931e commit ) the l2cap connection could not be established in case when the "Auth Complete" HCI event does not arive before the initiator send "Configuration request", in which case l2cap replies with "Command rejected" since the channel is still in BT_CONNECT2 state. Based on patch from: Ilia Kolomisnky <iliak@ti.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-06-30Bluetooth: Fix hidp disconnect deadlocks and lost wakeupPeter Hurley
Partial revert of commit aabf6f89. When the hidp session thread was converted from kernel_thread to kthread, the atomic/wakeups were replaced with kthread_stop. kthread_stop has blocking semantics which are inappropriate for the hidp session kthread. In addition, the kthread signals itself to terminate in hidp_process_hid_control() - it cannot do this with kthread_stop(). Lastly, a wakeup can be lost if the wakeup happens between checking for the loop exit condition and setting the current state to TASK_INTERRUPTIBLE. (Without appropriate synchronization mechanisms, the task state should not be changed between the condition test and the yield - via schedule() - as this creates a race between the wakeup and resetting the state back to interruptible.) Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-06-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits) usbnet: Remove over-broad module alias from zaurus. MAINTAINERS: drop Michael from bfin_mac driver net/can: activate bit-timing calculation and netlink based drivers by default rionet: fix NULL pointer dereference in rionet_remove net+crypto: Use vmalloc for zlib inflate buffers. netfilter: Fix ip_route_me_harder triggering ip_rt_bug ipv4: Fix IPsec slowpath fragmentation problem ipv4: Fix packet size calculation in __ip_append_data cxgb3: skb_record_rx_queue now records the queue index relative to the net_device. bridge: Only flood unregistered groups to routers qlge: Add maintainer. MAINTAINERS: mark socketcan-core lists as subscribers-only MAINTAINERS: Remove Sven Eckelmann from BATMAN ADVANCED r8169: fix wrong register use. net/usb/kalmia: signedness bug in kalmia_bind() net/usb: kalmia: Various fixes for better support of non-x86 architectures. rtl8192cu: Fix missing firmware load udp/recvmsg: Clear MSG_TRUNC flag when starting over for a new packet ipv6/udp: Use the correct variable to determine non-blocking condition netconsole: fix build when CONFIG_NETCONSOLE_DYNAMIC is turned on ...
2011-06-30Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into for-davem
2011-06-29netfilter: Fix ip_route_me_harder triggering ip_rt_bugJulian Anastasov
Avoid creating input routes with ip_route_me_harder. It does not work for locally generated packets. Instead, restrict sockets to provide valid saddr for output route (or unicast saddr for transparent proxy). For other traffic allow saddr to be unicast or local but if callers forget to check saddr type use 0 for the output route. The resulting handling should be: - REJECT TCP: - in INPUT we can provide addr_type = RTN_LOCAL but better allow rejecting traffic delivered with local route (no IP address => use RTN_UNSPEC to allow also RTN_UNICAST). - FORWARD: RTN_UNSPEC => allow RTN_LOCAL/RTN_UNICAST saddr, add fix to ignore RTN_BROADCAST and RTN_MULTICAST - OUTPUT: RTN_UNSPEC - NAT, mangle, ip_queue, nf_ip_reroute: RTN_UNSPEC in LOCAL_OUT - IPVS: - use RTN_LOCAL in LOCAL_OUT and FORWARD after SNAT to restrict saddr to be local Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-28Bluetooth: Prevent buffer overflow in l2cap config requestDan Rosenberg
A remote user can provide a small value for the command size field in the command header of an l2cap configuration request, resulting in an integer underflow when subtracting the size of the configuration request header. This results in copying a very large amount of data via memcpy() and destroying the kernel heap. Check for underflow. Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Cc: stable <stable@kernel.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-06-27ipv4: Fix IPsec slowpath fragmentation problemSteffen Klassert
ip_append_data() builds packets based on the mtu from dst_mtu(rt->dst.path). On IPsec the effective mtu is lower because we need to add the protocol headers and trailers later when we do the IPsec transformations. So after the IPsec transformations the packet might be too big, which leads to a slowpath fragmentation then. This patch fixes this by building the packets based on the lower IPsec mtu from dst_mtu(&rt->dst) and adapts the exthdr handling to this. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-27ipv4: Fix packet size calculation in __ip_append_dataSteffen Klassert
Git commit 59104f06 (ip: take care of last fragment in ip_append_data) added a check to see if we exceed the mtu when we add trailer_len. However, the mtu is already subtracted by the trailer length when the xfrm transfomation bundles are set up. So IPsec packets with mtu size get fragmented, or if the DF bit is set the packets will not be send even though they match the mtu perfectly fine. This patch actually reverts commit 59104f06. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-06-02 21:10:44 +0000