if ARCH_U8500

# Old bootloaders pass the Nomadik machine type, and the MACH_ option named
# after the machine type must be present and selected for machine_is_*() to
# work
config MACH_NOMADIK
	bool

config MACH_HREFV60
	bool

config MACH_SNOWBALL
	bool

choice
	prompt "Ux500 platform"
	default UX500_SOC_DB8500

config UX500_SOC_DB8500
	select CPU_V7
	select ARM_GIC
	select SMP
	select ARM_ERRATA_753970
	select SYS_SOC
	bool "U8500"

config UX500_SOC_DB5500
	select CPU_V7
	select ARM_GIC
	bool "U5500"

endchoice

config UX500_SVP
	bool

if UX500_SOC_DB8500

menu "U8500 Machines"

config MACH_SVP8500V1
	bool "U8500 Simulator v1 (SVP8500v1)"
	select UX500_SVP
	help
	  Support Simulation for u8500 platform (v1)

config MACH_SVP8500V2
	bool "U8500 Simulator v2 (SVP8500v2)"
	select UX500_SVP
	help
	  Supports Simulation for u8500 platform (v2)

config MACH_U8500
	bool "U8500 MOP500/HREF/custom HW"
	select MACH_NOMADIK
	select MACH_HREFV60
	help
	  Supports the generic U8500 board type used for MOP500/HREF and some
	  custom boards.  Boards using the generic type cannot be built
	  together; select the specific board in the "U8500 HW" option.

config MACH_SNOWBALL
	bool "U8500 Snowball"
	select MACH_U8500
	select MACH_NOMADIK
	help
	  Supports the Snowball board

# If you are porting onto a new board, you really should be using a new machine
# type and adding an entry into this list, not the "U8500 HW" list below.

endmenu

if MACH_U8500

choice
	prompt "U8500 HW"
	default MACH_U8500_MOP

config MACH_U8500_MOP
	bool "MOP500/HREF"
	help
	  Supports MOP500/HREF development boards.

config MACH_U8500_SNOWBALL
	bool "u8500 snowball"
	help
	  Support for the u8500 snowball board.

config MACH_U8500_PDP
	bool "PDP"
	help
	  Supports PDP target board

endchoice

endif

endif

if UX500_SOC_DB5500

menu "U5500 Machines"

config MACH_SVP5500
	bool "U5500 Simulator (SVP5500)"
	select UX500_SVP
	help
	  Support for the U5500 Simulator

config MACH_B5500
	bool "U5500 Big Board (B5500)"
	help
	  Support for the U5500 Big Board
endmenu

endif

choice
	prompt "Ux500 UIB Keylayout"
	default KEYLAYOUT_LAYOUT1

config KEYLAYOUT_LAYOUT1
	bool "UIB Keylayout 1; for generic users"
	help
	  Supported keylayout for some numerics, power/call buttons,
	  volume control etc

config KEYLAYOUT_LAYOUT2
	bool "UIB Keylayout 2; for connectivity users"
	help
	  Supports keylayout numerics 0-9, left/right/up/down/back/
	  enter keys and special character "."(dot)

endchoice

choice
	prompt "Ux500 sched_clock timer"
	default UX500_MTU_TIMER

config U8500_PRCMU_TIMER
	bool "PRCMU Timer sched_clock"
	depends on (UX500_SOC_DB8500 && !HAS_MTU)
	help
	  Add support for an always on sched_clock, required for
	  proper cpuidle and suspend.

config UX500_MTU_TIMER
	bool "Multi Timer Unit sched_clock"
	help
	  Add sched_clock support for the Multi Timer Unit.
	  Since mtu isn't always on cpuidle will not
	  work with this clock.

endchoice

config U8500_PRCMU
	bool "U8500 PRCMU support"
	depends on UX500_SOC_DB8500
	default n
	help
	  Add support for PRCMU for U8500

config U5500_PRCMU
	bool "U5500 PRCMU support"
	depends on UX500_SOC_DB5500
	default y
	help
	  Add support for PRCMU for U5500

config UX500_PRCMU_QOS_POWER
	bool "UX500 PRCMU power QoS support"
	depends on (U5500_PRCMU || U8500_PRCMU)
	default y
	help
	  Add support for PRCMU power Quality of Service

config UX500_PRCMU_DEBUG
	bool "PRCMU debug"
	depends on ((U5500_PRCMU || U8500_PRCMU) && DEBUG_FS)
	default n
	help
	  Add support for PRCMU debug

config U8500_REGULATOR_DEBUG
	bool "Regulator debug support"
	depends on REGULATOR_VIRTUAL_CONSUMER
	default n
	help
	  Add support for U8500 regulator debug

config U5500_PWM
	bool "PWM support"
	default y
	depends on UX500_SOC_DB5500
	help
	  Add support for PWM for U5500

config MOP500_SDI
	bool
	default y
	depends on ((MACH_U8500_MOP || \
		     MACH_U8500_PDP || \
		     MACH_U8500_SNOWBALL) && MMC_ARMMMCI)

config ARCH_HAS_CPU_IDLE_WAIT
	def_bool y

config UX500_DEBUG_UART
	int "Ux500 UART to use for low-level debug"
	default 2 if UX500_SOC_DB8500
	default 0 if UX500_SOC_DB5500
	help
	  Choose the UART on which kernel low-level debug messages should be
	  output.


config SENSORS1P_MOP
	tristate "HAL and Proximity sensors support"
	depends on REGULATOR && (GPIO_STMPE2401 || GPIO_TC35892)
	default y
	help
	  Add support for Osram's SFH7741 Proximity Sensor and Samsumg
	  HED54XXU11 HAL Switch

config U5500_MODEM_IRQ
	bool "Modem IRQ support"
	depends on UX500_SOC_DB5500
	default y
	help
	  Add support for handling IRQ:s from modem side

config MOP500_NUIB
	bool "MOP500 NUIB"
	depends on MACH_U8500_MOP
	default y
	help
	  Add support for the platform data of synaptics rmi4 driver

config TEE_UX500
	bool "Trusted Execution Environment (TEE) ux500 hardware support"
	depends on TEE_SUPPORT
	default y
	help
	  Adds TEE hardware support for ux500 platforms.

config TEE_SVP
	bool "Trusted Execution Environment (TEE) ux500 SVP support"
	depends on TEE_SUPPORT && UX500_SVP
	default y
	help
	  Adds TEE support for SVP in ux500 platforms.

config DB8500_MLOADER
	bool "Modem firmware upload/download support"
	depends on UX500_SOC_DB8500
	select DBX500_MLOADER
	default n
	help
	  Adds Modem firmware upload/download support to DB8500.

config UX500_DEBUG_HWREG
	bool "Debug hardware registers from userspace"
	depends on (DEBUG_FS && UX500_SOC_DB8500)
	help
	  Adds various debug files to access registers.
	  This should never ever be used for anything else than debugging.

config UX500_DEBUG_NO_LAUTERBACH
       bool "Disable clocks needed for Lauterbach debugging"
       help
	  Disable clocks needed for Lauterbach debugging at boot.
	  If yes, you will reduce the power consumption.

source "arch/arm/mach-ux500/Kconfig-arch"
source "arch/arm/mach-ux500/pm/Kconfig"
endif