ppc4xx: Netstal HCU5 board: added various fixes and POST

- Moved some common code to nestal/common/nm_bsp.c.
- Added support for the vxWorks EDR.
- Enable trace for Lauterbach, if present.
- Added support for POST.
- Stylistic cleanups (multi-line comments/ enforce 80 colomn width)

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

5 files changed, 206 insertions, 236 deletions

diff --git a/board/netstal/hcu5/Makefile b/board/netstal/hcu5/Makefile
index 27398b905..9645e455e 100644
--- a/board/netstal/hcu5/Makefile
+++ b/board/netstal/hcu5/Makefile
@@ -23,9 +23,10 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 vpath hcu_flash.c ../common
+vpath nm_bsp.c ../common
 
 # NOBJS : Netstal common objects
-NOBJS	= hcu_flash.o
+NOBJS	= hcu_flash.o nm_bsp.o
 COBJS	= $(BOARD).o sdram.o
 SOBJS	= init.o
 
diff --git a/board/netstal/hcu5/README.txt b/board/netstal/hcu5/README.txt
index 3118da9e0..c205108ff 100644
--- a/board/netstal/hcu5/README.txt
+++ b/board/netstal/hcu5/README.txt
@@ -10,9 +10,6 @@ TODO:
 - Fix RTS/CTS problem (HW?)
   CONFIG_SERIAL_MULTI/CONFIG_SERIAL_SOFTWARE_FIFO hangs after
   Switching to interrupt driven serial input mode
-- Make vxWorks start from u-boot. Possible reasons
-    - Does vxWorks need an entry for the Machine Check interrupt like this
-      tlbentry( 0x40000000, SZ_256M, 0, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) ?
 
 Caveats:
 --------
diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c
index b9b10fdc2..c5e0f086e 100644
--- a/board/netstal/hcu5/hcu5.c
+++ b/board/netstal/hcu5/hcu5.c
@@ -1,5 +1,5 @@
 /*
- *(C) Copyright 2005-2007 Netstal Maschinen AG
+ *(C) Copyright 2005-2008 Netstal Maschinen AG
  *    Niklaus Giger (Niklaus.Giger@netstal.com)
  *
  *    This source code is free software; you can redistribute it
@@ -21,13 +21,11 @@
 #include <common.h>
 #include <asm/processor.h>
 #include <ppc440.h>
-#include <asm/mmu.h>
-#include <net.h>
+#include <asm/io.h>
+#include  "../common/nm.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
-void hcu_led_set(u32 value);
-
 extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
 
 #undef BOOTSTRAP_OPTION_A_ACTIVE
@@ -42,23 +40,10 @@ extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
 #define SDR0_ECID2		0x0082
 #define SDR0_ECID3		0x0083
 
-#define SYS_IO_ADDRESS		(CFG_CS_2 + 0x00e00000)
+#define SYS_IO_ADDRESS			(CFG_CS_2 + 0x00e00000)
 #define SYS_SLOT_ADDRESS		(CFG_CPLD + 0x00400000)
-
-#define DEFAULT_ETH_ADDR  "ethaddr"
-/* ethaddr for first or etha1ddr for second ethernet */
-
-enum {
-	/* HW_GENERATION_HCU1 is no longer supported */
-	HW_GENERATION_HCU2  = 0x10,
-	HW_GENERATION_HCU3  = 0x10,
-	HW_GENERATION_HCU4  = 0x20,
-	HW_GENERATION_HCU5  = 0x30,
-	HW_GENERATION_MCU   = 0x08,
-	HW_GENERATION_MCU20 = 0x0a,
-	HW_GENERATION_MCU25 = 0x09,
-};
-
+#define HCU_DIGITAL_IO_REGISTER	(CFG_CPLD + 0x0500000)
+#define HCU_SW_INSTALL_REQUESTED	0x10
 
 /*
  * This function is run very early, out of flash, and before devices are
@@ -72,7 +57,6 @@ enum {
 
 int board_early_init_f(void)
 {
-	u32 reg;
 
 #ifdef BOOTSTRAP_OPTION_A_ACTIVE
 	/* Booting with Bootstrap Option A
@@ -113,10 +97,9 @@ int board_early_init_f(void)
 	mtdcr(ebccfga, xbcfg);
 	mtdcr(ebccfgd, 0xb8400000);
 
-	/*--------------------------------------------------------------------
+	/*
 	 * Setup the GPIO pins
-	 *-------------------------------------------------------------------*/
-	/* test-only: take GPIO init from pcs440ep ???? in config file */
+	 */
 	out32(GPIO0_OR, 0x00000000);
 	out32(GPIO0_TCR, 0x7C2FF1CF);
 	out32(GPIO0_OSRL, 0x40055000);
@@ -143,9 +126,9 @@ int board_early_init_f(void)
 	out32(GPIO1_ISR3L, 0x00000000);
 	out32(GPIO1_ISR3H, 0x00000000);
 
-	/*--------------------------------------------------------------------
+	/*
 	 * Setup the interrupt controller polarities, triggers, etc.
-	 *-------------------------------------------------------------------*/
+	 */
 	mtdcr(uic0sr, 0xffffffff);	/* clear all */
 	mtdcr(uic0er, 0x00000000);	/* disable all */
 	mtdcr(uic0cr, 0x00000005);	/* ATI & UIC1 crit are critical */
@@ -172,12 +155,6 @@ int board_early_init_f(void)
 	mtsdr(sdr_pfc0, 0x00003E00);	/* Pin function:  */
 	mtsdr(sdr_pfc1, 0x00848000);	/* Pin function: UART0 has 4 pins */
 
-	/* PCI arbiter enabled */
-	mfsdr(sdr_pci0, reg);
-	mtsdr(sdr_pci0, 0x80000000 | reg);
-
-	pci_pre_init(0);
-
 	/* setup BOOT FLASH */
 	mtsdr(SDR0_CUST0, 0xC0082350);
 
@@ -192,33 +169,27 @@ int board_pre_init(void)
 
 #endif
 
+int sys_install_requested(void)
+{
+	u16 *ioValuePtr = (u16 *)HCU_DIGITAL_IO_REGISTER;
+	return (in_be16(ioValuePtr) & HCU_SW_INSTALL_REQUESTED) != 0;
+}
+
 int checkboard(void)
 {
-	unsigned int j;
 	u16 *hwVersReg    = (u16 *) HCU_HW_VERSION_REGISTER;
 	u16 *boardVersReg = (u16 *) HCU_CPLD_VERSION_REGISTER;
-	u16 generation = *boardVersReg & 0xf0;
-	u16 index      = *boardVersReg & 0x0f;
+	u16 generation = in_be16(boardVersReg) & 0xf0;
+	u16 index      = in_be16(boardVersReg) & 0x0f;
 	u32 ecid0, ecid1, ecid2, ecid3;
 
-	printf("Netstal Maschinen AG: ");
-	if (generation == HW_GENERATION_HCU3)
-		printf("HCU3: index %d", index);
-	else if (generation == HW_GENERATION_HCU4)
-		printf("HCU4: index %d", index);
-	else if (generation == HW_GENERATION_HCU5)
-		printf("HCU5: index %d", index);
-	printf(" HW 0x%02x\n", *hwVersReg & 0xff);
+	nm_show_print(generation, index, in_be16(hwVersReg) & 0xff);
 	mfsdr(SDR0_ECID0, ecid0);
 	mfsdr(SDR0_ECID1, ecid1);
 	mfsdr(SDR0_ECID2, ecid2);
 	mfsdr(SDR0_ECID3, ecid3);
 
 	printf("Chip ID 0x%x 0x%x 0x%x 0x%x\n", ecid0, ecid1, ecid2, ecid3);
-	for (j = 0;j < 6; j++) {
-		hcu_led_set(1 << j);
-		udelay(200 * 1000);
-	}
 
 	return 0;
 }
@@ -228,97 +199,47 @@ u32 hcu_led_get(void)
 	return in16(SYS_IO_ADDRESS) & 0x3f;
 }
 
-/*---------------------------------------------------------------------------+
+/*
  * hcu_led_set  value to be placed into the LEDs (max 6 bit)
- *---------------------------------------------------------------------------*/
+ */
 void hcu_led_set(u32 value)
 {
 	out16(SYS_IO_ADDRESS, value);
 }
 
-/*---------------------------------------------------------------------------+
+/*
  * get_serial_number
- *---------------------------------------------------------------------------*/
-static u32 get_serial_number(void)
+ */
+u32 get_serial_number(void)
 {
 	u32 *serial = (u32 *)CFG_FLASH_BASE;
 
-	if (*serial == 0xffffffff)
+	if (in_be32(serial) == 0xffffffff)
 		return 0;
 
-	return *serial;
+	return in_be32(serial);
 }
 
 
-/*---------------------------------------------------------------------------+
+/*
  * hcu_get_slot
- *---------------------------------------------------------------------------*/
+ */
 u32 hcu_get_slot(void)
 {
 	u16 *slot = (u16 *)SYS_SLOT_ADDRESS;
-	return (*slot) & 0x7f;
+	return in_be16(slot) & 0x7f;
 }
 
 
-/*---------------------------------------------------------------------------+
+/*
  * misc_init_r.
- *---------------------------------------------------------------------------*/
+ */
 int misc_init_r(void)
 {
-	char *s = getenv(DEFAULT_ETH_ADDR);
-	char *e;
-	int i;
-	u32 serial = get_serial_number();
 	unsigned long usb2d0cr = 0;
 	unsigned long usb2phy0cr, usb2h0cr = 0;
 	unsigned long sdr0_pfc1;
 
-	for (i = 0; i < 6; ++i) {
-		gd->bd->bi_enetaddr[i] = s ? simple_strtoul(s, &e, 16) : 0;
-		if (s)
-			s = (*e) ? e + 1 : e;
-	}
-
-	if (gd->bd->bi_enetaddr[3] == 0 &&
-	    gd->bd->bi_enetaddr[4] == 0 &&
-	    gd->bd->bi_enetaddr[5] == 0) {
-		char ethaddr[22];
-
-		/* Must be in sync with CONFIG_ETHADDR */
-		gd->bd->bi_enetaddr[0] = 0x00;
-		gd->bd->bi_enetaddr[1] = 0x60;
-		gd->bd->bi_enetaddr[2] = 0x13;
-		gd->bd->bi_enetaddr[3] = (serial >> 16) & 0xff;
-		gd->bd->bi_enetaddr[4] = (serial >>  8) & 0xff;
-		gd->bd->bi_enetaddr[5] = hcu_get_slot();
-		sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X\0",
-			gd->bd->bi_enetaddr[0], gd->bd->bi_enetaddr[1],
-			gd->bd->bi_enetaddr[2], gd->bd->bi_enetaddr[3],
-			gd->bd->bi_enetaddr[4], gd->bd->bi_enetaddr[5]) ;
-		printf("%s: Setting eth %s serial 0x%x\n",  __FUNCTION__,
-		       ethaddr, serial);
-		setenv(DEFAULT_ETH_ADDR, ethaddr);
-	}
-
-	/* IP-Adress update */
-	{
-		IPaddr_t ipaddr;
-		char *ipstring;
-
-		ipstring = getenv("ipaddr");
-		if (ipstring == 0)
-			ipaddr = string_to_ip("172.25.1.99");
-		else
-			ipaddr = string_to_ip(ipstring);
-		if ((ipaddr & 0xff) != (32 + hcu_get_slot())) {
-			char tmp[22];
-
-			ipaddr = (ipaddr & 0xffffff00) + 32 + hcu_get_slot();
-			ip_to_string (ipaddr, tmp);
-			printf("%s: enforce %s\n",  __FUNCTION__, tmp);
-			setenv("ipaddr", tmp);
-		}
-	}
 #ifdef CFG_ENV_IS_IN_FLASH
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,
@@ -326,12 +247,14 @@ int misc_init_r(void)
 			    0xffffffff,
 			    &flash_info[0]);
 
+#ifdef CFG_ENV_ADDR_REDUND
 	/* Env protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,
 			    CFG_ENV_ADDR_REDUND,
 			    CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1,
 			    &flash_info[0]);
 #endif
+#endif
 
 	/*
 	 * USB stuff...
@@ -355,7 +278,8 @@ int misc_init_r(void)
 	usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;		/*1*/
 
 	/* An 8-bit/60MHz interface is the only possible alternative
-	   when connecting the Device to the PHY */
+	 *  when connecting the Device to the PHY
+	 */
 	usb2h0cr   = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
 	usb2h0cr   = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ;	/*1*/
 
@@ -376,14 +300,37 @@ int misc_init_r(void)
 	mtsdr(SDR0_SRST1, 0x00000000);
 	udelay(1000);
 	mtsdr(SDR0_SRST0, 0x00000000);
-
 	printf("USB:   Host(int phy) Device(ext phy)\n");
 
+	common_misc_init_r();
+	set_params_for_sw_install( sys_install_requested(), "hcu5" );
+	/* We cannot easily enable trace before, as there are other
+	 * routines messing around with sdr0_pfc1. And I do not need it.
+	 */
+	if (mfspr(dbcr0) & 0x80000000) {
+		/* External debugger alive
+		 * enable trace facilty for Lauterback
+		 * CCR0[DAPUIB]=0 	Enable broadcast of instruction data
+		 *			to auxiliary processor interface
+		 * CCR0[DTB]=0 		Enable broadcast of trace information
+		 * SDR0_PFC0[TRE] 	Trace signals are enabled instead of
+		 *			GPIO49-63
+		 */
+		mtspr(ccr0, mfspr(ccr0)  &~ 0x00108000);
+		mtsdr(SDR0_PFC0, sdr0_pfc1 | 0x00000100);
+	}
 	return 0;
 }
+#ifdef CONFIG_PCI
+int board_with_pci(void)
+{
+	u32 reg;
+
+	mfsdr(sdr_pci0, reg);
+	return (reg & SDR0_XCR_PAE_MASK);
+}
 
-#if defined(CONFIG_PCI)
-/*************************************************************************
+/*
  *  pci_pre_init
  *
  *  This routine is called just prior to registering the hose and gives
@@ -394,81 +341,64 @@ int misc_init_r(void)
  *	(add regions, override default access routines, etc) or perform
  *	certain pre-initialization actions.
  *
- ************************************************************************/
+ */
 int pci_pre_init(struct pci_controller *hose)
 {
 	unsigned long addr;
 
-	/*-------------------------------------------------------------------+
-	 * As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM.
-	 * Workaround: Disable write pipelining to DDR SDRAM by setting
-	 * PLB0_ACR[WRP] = 0.
-	 *-------------------------------------------------------------------*/
+	if (!board_with_pci()) { return 0; }
 
-	/*-------------------------------------------------------------------+
-	  | Set priority for all PLB3 devices to 0.
-	  | Set PLB3 arbiter to fair mode.
-	  +-------------------------------------------------------------------*/
+	/*
+	 * Set priority for all PLB3 devices to 0.
+	 * Set PLB3 arbiter to fair mode.
+	 */
 	mfsdr(sdr_amp1, addr);
 	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
 	addr = mfdcr(plb3_acr);
-	/* mtdcr(plb3_acr, addr & ~plb1_acr_wrp_mask); */  /* ngngng */
 	mtdcr(plb3_acr, addr | 0x80000000); /* Sequoia */
 
-	/*-------------------------------------------------------------------+
-	  | Set priority for all PLB4 devices to 0.
-	  +-------------------------------------------------------------------*/
+	/*
+	 * Set priority for all PLB4 devices to 0.
+	 */
 	mfsdr(sdr_amp0, addr);
 	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
 	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
-	/* mtdcr(plb4_acr, addr & ~plb1_acr_wrp_mask); */  /* ngngng */
 	mtdcr(plb4_acr, addr);  /* Sequoia */
 
-	/*-------------------------------------------------------------------+
-	  | Set Nebula PLB4 arbiter to fair mode.
-	  +-------------------------------------------------------------------*/
-	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
-	/* addr = (addr & ~plb0_acr_wrp_mask); */  /* ngngng */
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep; /* Sequoia */
-
-	/* mtdcr(plb0_acr, addr); */ /* Sequoia */
+	/*
+	 * As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM.
+	 * Workaround: Disable write pipelining to DDR SDRAM by setting
+	 * PLB0_ACR[WRP] = 0.
+	 */
 	mtdcr(plb0_acr, 0);  /* PATCH HAB: WRITE PIPELINING OFF */
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
-	addr = (addr & ~plb1_acr_wrp_mask) ;
-	/* mtdcr(plb1_acr, addr); */ /* Sequoia */
 	mtdcr(plb1_acr, 0);  /* PATCH HAB: WRITE PIPELINING OFF */
 
-	return 1;
+	return board_with_pci();
 }
 
-/*************************************************************************
+/*
  *  pci_target_init
  *
  *	The bootstrap configuration provides default settings for the pci
  *	inbound map (PIM). But the bootstrap config choices are limited and
  *	may not be sufficient for a given board.
  *
- ************************************************************************/
+ */
 void pci_target_init(struct pci_controller *hose)
 {
-	/*-------------------------------------------------------------+
+	if (!board_with_pci()) { return; }
+	/*
 	 * Set up Direct MMIO registers
-	 *-------------------------------------------------------------*/
-	/*-------------------------------------------------------------+
-	  | PowerPC440EPX PCI Master configuration.
-	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address
-	  |		  0xA0000000-0xDFFFFFFF
-	  |   Use byte reversed out routines to handle endianess.
-	  | Make this region non-prefetchable.
-	  +-------------------------------------------------------------*/
+	 *
+	 * PowerPC440EPX PCI Master configuration.
+	 * Map one 1Gig range of PLB/processor addresses to PCI memory space.
+	 *   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address
+	 *		  0xA0000000-0xDFFFFFFF
+	 *   Use byte reversed out routines to handle endianess.
+	 * Make this region non-prefetchable.
+	 */
 	/* PMM0 Mask/Attribute - disabled b4 setting */
 	out32r(PCIX0_PMM0MA, 0x00000000);
 	out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE);	/* PMM0 Local Address */
@@ -492,9 +422,9 @@ void pci_target_init(struct pci_controller *hose)
 	out32r(PCIX0_PTM2MS, 0);	/* Memory Size/Attribute */
 	out32r(PCIX0_PTM2LA, 0);	/* Local Addr. Reg */
 
-	/*------------------------------------------------------------------+
+	/*
 	 * Set up Configuration registers
-	 *------------------------------------------------------------------*/
+	 */
 
 	/* Program the board's subsystem id/vendor id */
 	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
@@ -513,26 +443,27 @@ void pci_target_init(struct pci_controller *hose)
 	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
 }
 
-/*************************************************************************
+/*
  *  pci_master_init
  *
- ************************************************************************/
+ */
 void pci_master_init(struct pci_controller *hose)
 {
 	unsigned short temp_short;
+	if (!board_with_pci()) { return; }
 
-	/*---------------------------------------------------------------+
-	  | Write the PowerPC440 EP PCI Configuration regs.
-	  |   Enable PowerPC440 EP to be a master on the PCI bus (PMM).
-	  |   Enable PowerPC440 EP to act as a PCI memory target (PTM).
-	  +--------------------------------------------------------------*/
+	/*---------------------------------------------------------------
+	 * Write the PowerPC440 EP PCI Configuration regs.
+	 *   Enable PowerPC440 EP to be a master on the PCI bus (PMM).
+	 *   Enable PowerPC440 EP to act as a PCI memory target (PTM).
+	 *--------------------------------------------------------------*/
 	pci_read_config_word(0, PCI_COMMAND, &temp_short);
 	pci_write_config_word(0, PCI_COMMAND,
 			      temp_short | PCI_COMMAND_MASTER |
 			      PCI_COMMAND_MEMORY);
 }
 
-/*************************************************************************
+/*
  *  is_pci_host
  *
  *	This routine is called to determine if a pci scan should be
@@ -545,10 +476,31 @@ void pci_master_init(struct pci_controller *hose)
  *
  *	Return 0 for adapter mode, non-zero for host (monarch) mode.
  *
- *
- ************************************************************************/
+ */
 int is_pci_host(struct pci_controller *hose)
 {
 	return 1;
 }
 #endif	 /* defined(CONFIG_PCI) */
+
+#if defined(CONFIG_POST)
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+	return 0;	/* No hotkeys supported */
+}
+#endif /* CONFIG_POST */
+
+#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	u32 val[4];
+	int rc;
+
+	ft_cpu_setup(blob, bd);
+
+}
+#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
diff --git a/board/netstal/hcu5/init.S b/board/netstal/hcu5/init.S
index 5ab6cd24d..188272e78 100644
--- a/board/netstal/hcu5/init.S
+++ b/board/netstal/hcu5/init.S
@@ -39,41 +39,68 @@
 tlbtab:
 	tlbtab_start
 
-	/* vxWorks needs this entry for the Machine Check interrupt,  */
-	/* tlbentry( 0x40000000, SZ_256M, 0, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) */
+	/* TLB#0: vxWorks needs this entry for the Machine Check interrupt, */
+	tlbentry( 0x40000000, SZ_256M, 0, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
+	/* TLB#1: TLB-entry for DDR SDRAM (Up to 2GB) */
+	tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0,
+		AC_R|AC_W|AC_X|SA_G|SA_I )
+
+	/* TLB#2: TLB-entry for EBC */
+	tlbentry( 0x80000000, SZ_256M, 0x80000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I)
 
 	/*
-	 * BOOT_CS (FLASH) must be second. Before relocation SA_I can be off to use the
-	 * speed up boot process. It is patched after relocation to enable SA_I
+	 * TLB#3: BOOT_CS (FLASH) must be forth. Before relocation SA_I can be
+	 * off to use the speed up boot process. It is patched after relocation
+	 * to enable SA_I
 	 */
-	tlbentry( CFG_BOOT_BASE_ADDR, SZ_1M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G )
+	tlbentry( CFG_BOOT_BASE_ADDR, SZ_1M, CFG_BOOT_BASE_ADDR, 1,
+		AC_R|AC_W|AC_X|SA_G)
 
-	/* TLB-entry for PCI Memory */
-	tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 1, AC_R|AC_W|SA_G|SA_I )
-	tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 1, AC_R|AC_W|SA_G|SA_I )
-	tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I )
-	tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I )
+	/*
+	 * TLB entries for SDRAM are not needed on this platform.
+	 * They are dynamically generated in the SPD DDR(2) detection
+	 * routine.
+	 */
 
-	/* TLB-entry for EBC (CFG_CPLD) */
-	/* tlbentry( CFG_CPLD, SZ_1K, CFG_CPLD, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) */
-	/* 		CAN */
-	tlbentry( CFG_CS_1, SZ_16M, CFG_CS_1, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
-	 /* 		IMC + CPLD */
-	tlbentry( CFG_CS_2, SZ_16M, CFG_CS_2, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
-	tlbentry( CFG_CS_2 + 0x1000000, SZ_16M, CFG_CS_2 + 0x1000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
-	 /* 		IMC-Fast */
-	tlbentry( CFG_CS_3, SZ_16M, CFG_CS_3, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
-	tlbentry( CFG_CS_3 + 0x1000000, SZ_16M, CFG_CS_3 + 0x1000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+	/* TLB#4: */
+	tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 1,
+		AC_R|AC_W|SA_G|SA_I )
+	/* TLB#5: */
+	tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1,
+		AC_R|AC_W|SA_G|SA_I )
+	/* TLB#6: */
+	tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1,
+		AC_R|AC_W|SA_G|SA_I )
 
 	/* TLB-entry for Internal Registers & OCM */
-	tlbentry( CFG_PCI_BASE, SZ_16M, 0xe0000000, 0,  AC_R|AC_W|AC_X|SA_I )
+	/* TLB#7: */
+	tlbentry( 0xe0000000, SZ_16M, 0xe0000000, 0,
+		AC_R|AC_W|AC_X|SA_G|SA_I )
 
 	/*TLB-entry PCI registers*/
+	/* TLB#8: */
 	tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1,  AC_R|AC_W|AC_X|SA_G|SA_I )
 
 	/* TLB-entry for peripherals */
+	/* TLB#9: */
 	tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I)
 
-	/* TLB for SDRAM will be added by initdram (sdram.c) */
+	/* 		CAN */
+	/* TLB#10: */
+	tlbentry( CFG_CS_1, SZ_1K, CFG_CS_1, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+
+	/* TLB#11:  CPLD and IMC-Standard 32 MB */
+	tlbentry( CFG_CS_2, SZ_16M, CFG_CS_2, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+
+	/* TLB#12: */
+	tlbentry( CFG_CS_2 + 0x1000000, SZ_16M, CFG_CS_2 + 0x1000000, 1,
+		AC_R|AC_W|AC_X|SA_G|SA_I )
+
+	 /* 		IMC-Fast 32 MB */
+	/* TLB#13: */
+	tlbentry( CFG_CS_3, SZ_16M, CFG_CS_3, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+	/* TLB#14: */
+	tlbentry( CFG_CS_3 + 0x1000000, SZ_16M, CFG_CS_3, 1,
+		AC_R|AC_W|AC_X|SA_G|SA_I )
 
 	tlbtab_end
diff --git a/board/netstal/hcu5/sdram.c b/board/netstal/hcu5/sdram.c
index cbb2839cc..83d94563f 100644
--- a/board/netstal/hcu5/sdram.c
+++ b/board/netstal/hcu5/sdram.c
@@ -62,11 +62,8 @@ void dflush(void);
 #define DDR0_22_CTRL_RAW_ECC_ENABLE       0x03000000 /* ECC correcting on */
 #define DDR0_03_CASLAT_DECODE(n)            ((((unsigned long)(n))>>16)&0x7)
 
-#ifdef CFG_ENABLE_SDRAM_CACHE
-#define MY_TLB_WORD2_I_ENABLE	0		/* enable caching on DDR2 */
-#else
-#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on DDR2 */
-#endif
+#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE
+	/* disable caching on DDR2 */
 
 void program_tlb(u32 phys_addr, u32 virt_addr, u32 size, u32 tlb_word2_i_value);
 
@@ -157,38 +154,36 @@ static void blank_string(int size)
 /*---------------------------------------------------------------------------+
  * program_ecc.
  *---------------------------------------------------------------------------*/
-static void program_ecc(unsigned long start_address, unsigned long num_bytes,
-			unsigned long tlb_word2_i_value)
+static void program_ecc(unsigned long start_address, unsigned long num_bytes)
 {
-	unsigned long current_address= start_address;
-	int loopi = 0;
 	u32 val;
-
 	char str[] = "ECC generation -";
-	char slash[] = "\\|/-\\|/-";
+#if defined(CONFIG_PRAM)
+	u32 *magic;
+
+	/* Check whether vxWorks is using EDR logging, if yes zero */
+	/* also PostMortem and user reserved memory */
+	magic= in_be32(start_address  + num_bytes -
+			(CONFIG_PRAM*1024) + sizeof(u32));
+
+	debug("\n%s:  CONFIG_PRAM %d kB magic 0x%x 0x%p -> 0x%x\n", __FUNCTION__,
+	       CONFIG_PRAM,
+	       start_address  + num_bytes - (CONFIG_PRAM*1024) + sizeof(u32),
+	       magic, in_be32(magic));
+	if (in_be32(magic) == 0xbeefbabe)
+		num_bytes -= (CONFIG_PRAM*1024)  - PM_RESERVED_MEM;
+#endif
+
 
 	sync();
 	eieio();
 
 	puts(str);
 
-	if (tlb_word2_i_value == TLB_WORD2_I_ENABLE) {
-		/* ECC bit set method for non-cached memory */
-		/* This takes various seconds */
-		for(current_address = 0; current_address < num_bytes;
-		     current_address += sizeof(u32)) {
-			*(u32 *)current_address = 0;
-			if ((current_address % (2 << 20)) == 0) {
-				putc('\b');
-				putc(slash[loopi++ % 8]);
-			}
-		}
-	} else {
-		/* ECC bit set method for cached memory */
-		/* Fast method, no noticeable delay */
-		dcbz_area(start_address, num_bytes);
-		dflush();
-	}
+	/* ECC bit set method for cached memory */
+	/* Fast method, no noticeable delay */
+	dcbz_area(start_address, num_bytes);
+	dflush();
 	blank_string(strlen(str));
 
 	/* Clear error status */
@@ -196,7 +191,7 @@ static void program_ecc(unsigned long start_address, unsigned long num_bytes,
 	mtsdram(DDR0_00, val | DDR0_00_INT_ACK_ALL);
 
 	/*
-	 * Clear possible errors
+	 * Clear possible ECC errors
 	 * If not done, then we could get an interrupt later on when
 	 * exceptions are enabled.
 	 */
@@ -212,6 +207,7 @@ static void program_ecc(unsigned long start_address, unsigned long num_bytes,
 
 #endif
 
+
 /***********************************************************************
  *
  * initdram -- 440EPx's DDR controller is a DENALI Core
@@ -233,23 +229,22 @@ long int initdram (int board_type)
 	mtsdram(DDR0_04, 0x0A020200);
 	mtsdram(DDR0_05, 0x02020307);
 	switch (*hwVersReg & HCU_HW_SDRAM_CONFIG_MASK) {
-	case 0:
-		dram_size = 128 * 1024 * 1024 ;
-		mtsdram(DDR0_06, 0x0102C80D);  /* 128MB RAM */
-		mtsdram(DDR0_11, 0x000FC800);  /* 128MB RAM */
-		mtsdram(DDR0_43, 0x030A0300);  /* 128MB RAM */
-		break;
 	case 1:
 		dram_size = 256 * 1024 * 1024 ;
 		mtsdram(DDR0_06, 0x0102C812);  /* 256MB RAM */
 		mtsdram(DDR0_11, 0x0014C800);  /* 256MB RAM */
 		mtsdram(DDR0_43, 0x030A0200);  /* 256MB RAM */
 		break;
+	case 0:
 	default:
-		sdram_panic(INVALID_HW_CONFIG);
+		dram_size = 128 * 1024 * 1024 ;
+		mtsdram(DDR0_06, 0x0102C80D);  /* 128MB RAM */
+		mtsdram(DDR0_11, 0x000FC800);  /* 128MB RAM */
+		mtsdram(DDR0_43, 0x030A0300);  /* 128MB RAM */
 		break;
 	}
 	mtsdram(DDR0_07, 0x00090100);
+
 	/*
 	 * TCPD=200 cycles of clock input is required to lock the DLL.
 	 * CKE must be HIGH the entire time.mtsdram(DDR0_08, 0x02C80001);
@@ -288,7 +283,7 @@ long int initdram (int board_type)
 	 * Program tlb entries for this size (dynamic)
 	 */
 	remove_tlb(CFG_SDRAM_BASE, 256 << 20);
-	program_tlb(0, 0, dram_size, MY_TLB_WORD2_I_ENABLE);
+	program_tlb(0, 0, dram_size, TLB_WORD2_W_ENABLE | TLB_WORD2_I_ENABLE);
 
 	/*
 	 * Setup 2nd TLB with same physical address but different virtual
@@ -296,13 +291,11 @@ long int initdram (int board_type)
 	 */
 	program_tlb(0, CFG_DDR_CACHED_ADDR, dram_size, 0);
 
-	/* Diminish RAM to initialize */
-	dram_size = dram_size - 32 ;
 #ifdef CONFIG_DDR_ECC
 	/*
 	 * If ECC is enabled, initialize the parity bits.
 	 */
-	program_ecc(CFG_DDR_CACHED_ADDR, dram_size, 0);
+	program_ecc(CFG_DDR_CACHED_ADDR, dram_size);
 #endif
 
 	return (dram_size);