diff options
Diffstat (limited to 'board/amcc/canyonlands/canyonlands.c')
| -rw-r--r-- | board/amcc/canyonlands/canyonlands.c | 130 |
1 files changed, 3 insertions, 127 deletions
diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c index 91fae1917..13a0daced 100644 --- a/board/amcc/canyonlands/canyonlands.c +++ b/board/amcc/canyonlands/canyonlands.c @@ -326,141 +326,17 @@ phys_size_t initdram(int board_type) } #endif -/* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - */ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller * hose ) -{ - /* - * Disable everything - */ - out_le32((void *)PCIL0_PIM0SA, 0); /* disable */ - out_le32((void *)PCIL0_PIM1SA, 0); /* disable */ - out_le32((void *)PCIL0_PIM2SA, 0); /* disable */ - out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */ - - /* - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 - * strapping options to not support sizes such as 128/256 MB. - */ - out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE); - out_le32((void *)PCIL0_PIM0LAH, 0); - out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1); - out_le32((void *)PCIL0_BAR0, 0); - - /* - * Program the board's subsystem id/vendor id - */ - out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID); - out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID); - - out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - #if defined(CONFIG_PCI) -/* - * is_pci_host - * - * This routine is called to determine if a pci scan should be - * performed. With various hardware environments (especially cPCI and - * PPMC) it's insufficient to depend on the state of the arbiter enable - * bit in the strap register, or generic host/adapter assumptions. - * - * Rather than hard-code a bad assumption in the general 440 code, the - * 440 pci code requires the board to decide at runtime. - * - * Return 0 for adapter mode, non-zero for host (monarch) mode. - */ -int is_pci_host(struct pci_controller *hose) +int board_pcie_first(void) { - /* Board is always configured as host. */ - return (1); -} - -static struct pci_controller pcie_hose[2] = {{0},{0}}; - -void pcie_setup_hoses(int busno) -{ - struct pci_controller *hose; - int i, bus; - int ret = 0; - char *env; - unsigned int delay; - int start; - - /* - * assume we're called after the PCIX hose is initialized, which takes - * bus ID 0 and therefore start numbering PCIe's from 1. - */ - bus = busno; - /* * Canyonlands with SATA enabled has only one PCIe slot * (2nd one). */ if (gd->board_type == BOARD_CANYONLANDS_SATA) - start = 1; - else - start = 0; - - for (i = start; i <= 1; i++) { + return 1; - if (is_end_point(i)) - ret = ppc4xx_init_pcie_endport(i); - else - ret = ppc4xx_init_pcie_rootport(i); - if (ret == -ENODEV) - continue; - if (ret) { - printf("PCIE%d: initialization as %s failed\n", i, - is_end_point(i) ? "endpoint" : "root-complex"); - continue; - } - - hose = &pcie_hose[i]; - hose->first_busno = bus; - hose->last_busno = bus; - hose->current_busno = bus; - - /* setup mem resource */ - pci_set_region(hose->regions + 0, - CONFIG_SYS_PCIE_MEMBASE + i * CONFIG_SYS_PCIE_MEMSIZE, - CONFIG_SYS_PCIE_MEMBASE + i * CONFIG_SYS_PCIE_MEMSIZE, - CONFIG_SYS_PCIE_MEMSIZE, - PCI_REGION_MEM); - hose->region_count = 1; - pci_register_hose(hose); - - if (is_end_point(i)) { - ppc4xx_setup_pcie_endpoint(hose, i); - /* - * Reson for no scanning is endpoint can not generate - * upstream configuration accesses. - */ - } else { - ppc4xx_setup_pcie_rootpoint(hose, i); - env = getenv ("pciscandelay"); - if (env != NULL) { - delay = simple_strtoul(env, NULL, 10); - if (delay > 5) - printf("Warning, expect noticable delay before " - "PCIe scan due to 'pciscandelay' value!\n"); - mdelay(delay * 1000); - } - - /* - * Config access can only go down stream - */ - hose->last_busno = pci_hose_scan(hose); - bus = hose->last_busno + 1; - } - } + return 0; } #endif /* CONFIG_PCI */ |