| Age | Commit message (Collapse) | Author |
|---|
|
We already map the page cache-inhibited. There is no reason we
shouldn't also be marking it guarded to prevent speculative accesses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The e500mc core supports the ability to stash into the L1 or L2 cache,
however we need to uniquely identify the caches with an id.
We use the following equation to set the various stash-ids:
32 + coreID*2 + 0(L1) or 1(L2)
The 0 (for L1) or 1 (for L2) matches the CT field used be various cache
control instructions.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
We need loop-check the flash clear lock and enable bit for L2 cache.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This change has 3 goals:
- Have secondary cores be released into spin loops at their 'true'
address in SDRAM. Previously, secondary cores were put into spin
loops in the 0xfffffxxx address range which required that boot page
translation was always enabled while cores were in their spin loops.
- Allow the TLB window that the primary core uses to access the
secondary cores boot page to be placed at any address. Previously, a
TLB window at 0xfffff000 was always used to access the seconary cores'
boot page. This TLB address requirement overlapped with other
peripherals on some boards (eg XPedite5370). By default, the boot
page TLB will still use the 0xfffffxxx address range, but this can be
overridden on a board-by-board basis by defining a custom
CONFIG_BPTR_VIRT_ADDR. Note that the TLB used to map the boot page
remains in use while U-Boot executes. Previously it was only
temporarily used, then restored to its initial value.
- Allow Boot Page Translation to be disabled on bootup. Previously,
Boot Page Translation was always left enabled after secondary cores
were brought out of reset. This caused the 0xfffffxxx address range
to somewhat "magically" be translated to an address in SDRAM. Some
boards may not want this oddity in their memory map, so defining
CONFIG_MPC8xxx_DISABLE_BPTR will turn off Boot Page Translation after
the secondary cores are initialized.
These changes are only applicable to 85xx boards with CONFIG_MP defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
We need to flash invalidate the locks in addition to the cache
before we enable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
In future Book-E implementations IVORs will most likely go away and be
replaced with fixed offsets. The IVPR will continue to exist to allow
for relocation of the interrupt vectors.
This code adds support to setup the IVORs as their fixed offset values
per the ISA 2.06 spec when we transition from u-boot to another OS
either via 'bootm' or a cpu release.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The number of CPUs are getting detected dynamically by checking the
processor SVR value. Also removed CONFIG_NUM_CPUS references from all
the platforms with 85xx/86xx processors.
This can help to use the same u-boot image across the platforms.
Also revamped and corrected few Freescale Copyright messages.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
* Enable backside L2
* e500mc no longer has timebase enable in HID (moved to CCSR register)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Assuming the OSes exception vectors start from the base of kernel address, and
the kernel physical starting address can be relocated to an non-zero address.
This patch enables the second core to have a valid IVPR for debugger before
kernel setting IVPR in CAMP mode. Otherwise, IVPR is 0x0 and it is not a valid
value for second core which runs kernel at different physical address other
than 0x0.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
|
|
Introduce CONFIG_E500MC to deal with the minor differences between
e500v2 and e500mc.
* Certain fields of HID0/1 don't exist anymore on e500mc
* Cache line size is 64-bytes on e500mc
* reset value of PIR is different
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The e500um says the timebase is volatile out of reset. To ensure
TB sync works we need to make sure its zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Use CONFIG_NUM_CPUS to match existing define used by 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
|
|
* adjust __spin_table alignment to match ePAPR v0.94 spec
* loop over all cpus when determing who is up. This fixes an issue if
the "boot cpu" isn't core0. The "boot cpu" will already be in the
cpu_up_mask so there is no harm
* Added some protection in the code to ensure proper behavior. These
changes are explicitly needed but don't hurt:
- Added eieio to ensure the "hot word" of the table is written after
all other table updates have occurred.
- Added isync to ensure we don't prefetch loading of table entries
until we a released
These issues we raised by Dave Liu.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The following changes are needed to be inline with ePAPR v0.81:
* r4, r5 and now always set to 0 on boot release
* r7 is used to pass the size of the initial map area (IMA)
* EPAPR_MAGIC value changed for book-e processors
* changes in the spin table layout
* spin table supports a 64-bit physical release address
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Added the cpu command that provides a generic mechanism to get status,
reset, and release secondary cores in multicore processors.
Added support for using the ePAPR defined spin-table mechanism on 85xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
