summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2012-03-23snowball: fix incorrect root= parameter for eMMC bootHEADmasterLee Jones
Erronrous root= parameter causes "Kernel panic - not syncing: No init found" After applying this patch Snowball boots successfully to a shell again. Signed-off-by: Lee Jones <lee.jones@linaro.org>
2012-03-06snowball: pushing vmalloc to 300MMathieu J. Poirier
This is to address the following bug: https://bugs.launchpad.net/igloocommunity/+bug/934034 Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2012-02-08snowball: android: increasing mali memory regionMathieu J. Poirier
This is fixing bug: https://bugs.launchpad.net/igloocommunity/+bug/925913 Signed-off-by: Benn Porscke <benn.porscke@stericsson.com> Committer: Mathieu Poirier <mathieu.poirier@linaro.org>
2012-02-02Add support for boot.scr filer on emmc.Benn Pörscke
If a boot.scr file exist in a fat partition on the emmc it will be used.
2011-11-25Remove automatic IP acquiring from kernel commandlineKalle Vahlman
It delays the boot for all, although useful only for those using network based filesystems as rootfs.
2011-11-17Corrected bad memargs1024Mats Bergstrom
2011-11-09Adding absolute path convention to boot.scrMathieu J. Poirier
Files fetched by 'fat load' must use absolute path, otherwize the command fails. Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-06-17Fixing backslash zero '\0' in 'commonargs' variable.2011.08.252011.08.23Mathieu Poirier
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-06-01Added vmalloc parameter to default environment.Tony Månsson
2011-05-31Silencing TOC and itp error messages not applicable to snowball.Mathieu J. Poirier
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-05-27Tailoring boot algorithm for snowballMathieu J. Poirier
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-02-17Adding official machine ID.Mathieu J. Poirier
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-02-14Adding base support for snowball.Mathieu J. Poirier
- Initial pin configuration. - Introduction of u8500_is_snowball. - Introduction of new machine type. Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-02-14Adding compilation support for snowball.Mathieu J. Poirier
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
2011-01-31U8500: Kick the Cortex watchdog when dumpingPer Fransson
ST-Ericsson ID: 321908 Change-Id: Ib51c36558e37c7f52db638052644758e6d3cc51a Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/13848 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2011-01-28U8500: Change display reset for HREFP 2.0 V60 and laterMichael Brandt
The HREFP 2.0 V60 has no GPIO expander and the display reset IO line was moved to an ordinary GPIO line. Furthermore move the board dependent routine out from the mcde driver into u8500.c ST-Ericsson ID: CR 272893 Change-Id: If1362cecaeb183e67273066f759e220672f4537f Signed-off-by: Michael Brandt <michael.brandt@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/13480 Reviewed-by: Dan JOHANSSON <dan.johansson@stericsson.com> Reviewed-by: QATOOLS Reviewed-by: Joakim AXELSSON <joakim.axelsson@stericsson.com> Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com>
2011-01-27db8500: Verify signature of kernel before bootingRobert Rosengren
Verification of the kernel and ITP signature before allowing to boot is added. This feature is configurable and by default not activated. MeeGo- built RPM will have this enabled. ST-Ericsson ID: WP275634, ER275440 Change-Id: Ib888f39dd5dca1bc8b7d6e1b002da83a77908b07 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/11415 Tested-by: Robert ROSENGREN <robert.rosengren@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: QATOOLS Reviewed-by: Jens WIKLANDER <jens.wiklander@stericsson.com>
2011-01-18U8500: Add support for HREFP 2.0 V60 and laterMichael Brandt
The HREFP 2.0 V60 has no GPIO expander, therefore some GPIO lines were moved around. The preferred approach was to first check if there is a machid in the environment. And if not try to program the GPIOE. If that fails, assume it is a V60 or newer. But for the splash screen, we need to know very early on which HW version we are running. At that time no environment is available, therefore it is unavoidable to do the I2C access (10 ms timeout), if both HW versions shall be supported in one binary. CAUTION: you need also a Linux kernel which supports MACH_TYPE_HREFV60. Older U8500 kernels will not even issue a start-up message. Depends-On: http://gerrit.lud.stericsson.com/gerrit/12335 ST-Ericsson ID: CR 272893 Change-Id: Id794df8c185dfbf67f7bce81deb49abf71129f7b Signed-off-by: Michael Brandt <michael.brandt@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/12578 Reviewed-by: Torbjorn SVENSSON <torbjorn.x.svensson@stericsson.com> Reviewed-by: Robert ROSENGREN <robert.rosengren@stericsson.com> Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com> Reviewed-by: Bibek BASU <bibek.basu@stericsson.com>
2011-01-18U8500: Generic display driverTorbjorn Svensson
This patch introduces combined DSI and DPI display support for u-boot. The code is also similar to the kernel code for easy maintenance. ST-Ericsson ID: ER319241 ST-Ericsson FOSS-OUT ID: STETL-FOSS-OUT-10069 Change-Id: Ic232b6f738348cbedb67e27418678ddd223d7800 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/11038 Reviewed-by: Jimmy RUBIN <jimmy.rubin@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Torbjorn SVENSSON <torbjorn.x.svensson@stericsson.com>
2010-12-15Removal of executable permissionRobert Rosengren
General removal of executable permission of built source and header files, i.e. changing permission from 755 to 644. ST-Ericsson ID: None ST-Ericsson FOSS-OUT ID: Trivial Change-Id: Ic3cfc551d1ef1b1f0b5825f9916d1fc15b15b444 Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/10896 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Joakim AXELSSON <joakim.axelsson@stericsson.com>
2010-12-15db8500: Move ISSW code out from itp.cRobert Rosengren
Splitting security related code from itp.c into sec_bridge.c ST-Ericsson ID: WP275634 ST-Ericsson FOSS-OUT ID: Trivial Change-Id: I813daf0d0eaea4645e7d990bf467f19b0af968db Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/10895 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-15U8500: Move itp and cspsa into SoC directoryRobert Rosengren
itp.c and cspsa_fp.c is SoC specific, not board specific. Other db8500 based boards need it as well, therefore move it into the SoC directory. ST-Ericsson ID: WP275634 ST-Ericsson FOSS-OUT ID: Trivial Change-Id: I386c0d84e9f44f18ded0d9059fc2dae4c27974f2 Signed-off-by: Robert Rosengren <robert.rosengren@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/10894 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com> Reviewed-by: Joakim AXELSSON <joakim.axelsson@stericsson.com>
2010-12-13U8500: Changes to use a bmp file as splash imageTorbjorn Svensson
This change makes it possible to use a bitmap file (.bmp) as the splash image. This also removes the need to specify width and height of the splash image. RLE compression, 1 and 4 bit formats are not supported. ST-Ericsson ID: AP281072 Change-Id: I7c9ae953ad0440b665bb03ed1b9bbf43bab04e91 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9406 Tested-by: Torbjorn SVENSSON <torbjorn.x.svensson@stericsson.com> Reviewed-by: QATOOLS Reviewed-by: Jimmy RUBIN <jimmy.rubin@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: New GPIO driver and config, from Linux kernelJoakim Axelsson
Copied the GPIO configurator written for the Linux kernel. The Nomadik db8500 GPIO driver. Purpose is to be able to just cut-n-paste the GPIO config from Linux to U-boot. Also at the same time remove the obsolete and old gpio_alt_funcenable/disable methods. Now all is configured using a table in u8500.c. Now drivers doesn't have to worry about setting up the GPIO pins. Actually no driver today uses GPIO pins directly, only via hardware blocks within db8500. Functions are still added to be able to interact directly with a GPIO pin. This also cleaned up a lot of driver by not having to bit manipulate GPIO registers them self. The new driver is called db8500_gpio and placed in driver/gpio/. Functions are in include/db8500_gpio.h: void db8500_gpio_set_pull(unsigned gpio, enum db8500_gpio_pull pull); void db8500_gpio_make_input(unsigned gpio); int db8500_gpio_get_input(unsigned gpio); void db8500_gpio_make_output(unsigned gpio, int val); void db8500_gpio_set_output(unsigned gpio, int val); And for the configurator in include/db8500_pincfg.h: void db8500_gpio_config_pins(pin_cfg_t *cfgs, size_t num); All in all the final binary size has decreased. This is only done for db8500 nomadik GPIO. The code for gpio expanders has not been touched. All references to Nomadik has been removed in this driver. Only db8500 is left. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: I90aa1d46c813ffb5a777c3492b5751f5054f71cf Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9904 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Clean up PRCMU code in db8500 SoC codeJoakim Axelsson
Clean up of PRCMU code in db8500 SoC code. Move things from cpu.c and clock.h to prcmu.c. Also remove duplicate #defines and have prcmu.c use the #defines in prcmu.h. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: Ieffb0094b3f43f0c88f3ed457c6cb296fa0ce378 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9899 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Display cpu info.Joakim Axelsson
Enable CONFIG_DISPLAY_CPUINFO and implement print_cpuinfo() in cpu/arm_cortexa9/db8500.c. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: Id4f67b223fabc4a8007229f8db12bd2a7362f8c2 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7115 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Move all clock code from board to SoCJoakim Axelsson
Moved clock code from board/st/u8500/u8500.c to cpu/arm_cortexa9/db8500/clock.c. Remove code to simulate Maja clocks. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: Ibbb21d53091ceaddcc01e1a195e129039f986696 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7114 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Move cpu identifying function to SoC codeJoakim Axelsson
Moved u8500_is_earlydrop() and cpu_is_u8500*() to include/asm-arm/arch-db8500/cpu.h. They are kept in cpu.h as the functions are very small and should be inlined with each use of them. The final binary actually also became around 100 bytes smaller. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: Ied553b7c8a004a37c70c3e328a069ae8b2a92b23 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9893 Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-08db8500: Split arch_cpu code from boardJoakim Axelsson
First patch to split cpu_arch SoC-code away from board code. Added usage of arch_cpu_init() which is the corresponding to board_init(). Moved db8500 code from board/st/u8500/u8500.c to cpu/arm_cortexa9/db8500/cpu.c. Also created include/asm/arch-db8500/cpu.h and include/asm/arch-db8500/prcmu.h. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: I403d7d4f6c655c0d383afb3cb3be7e7df96683a3 Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7150 Reviewed-by: Joakim AXELSSON <joakim.axelsson@stericsson.com> Tested-by: Joakim AXELSSON <joakim.axelsson@stericsson.com> Reviewed-by: QATOOLS Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-12-07db8500: cpu-arch rename stw8500 to db8500Joakim Axelsson
Started work with splitting the files in board/st/u8500 into proper SoC (system on a chip), drivers, commands and board code. ST-Ericsson ID: None Signed-off-by: Joakim Axelsson <joakim.axelsson@stericsson.com> Change-Id: I33300b1990f377bc049785102f1c87fbe579e86d Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7089 Reviewed-by: Robert ROSENGREN <robert.rosengren@stericsson.com> Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Mikael LARSSON1 <mikael.xt.larsson@stericsson.com>
2010-11-23U8500: config: removed non-applicable and unused definesMichael Brandt
Some defines were inherited from the old U-Boot 1.3.1 and are not used anywhere. This patch removes them. As a side-effect the flash.c dummy was also removed. Change-Id: Iecddb2f8bb59d909b936254085c358a1d246d205 Signed-off-by: Michael Brandt <michael.brandt@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9203 Reviewed-by: Sebastian RASMUSSEN <sebastian.rasmussen@stericsson.com> Reviewed-by: Robert ROSENGREN <robert.rosengren@stericsson.com>
2010-11-19U8500: Removed duplicates of common.h and gpio.hMichael Brandt
common.h and gpio.h were present in the u8500 board directory and in the SoC include directory include/asm-arch/arch-stw8500. This patch removes the duplicates in the board directory and replaces all "common.h" and "gpio.h" with <asm/arch/common.h> and <asm/arch/gpio.h>, respectively. Change-Id: I4ff2a3a11324200222e3ae5b9d22eee6427f6d4c Signed-off-by: Michael Brandt <michael.brandt@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/8838 Reviewed-by: Markus HELGESSON <markus.helgesson@stericsson.com> Reviewed-by: Rikard OLSSON <rikard.p.olsson@stericsson.com>
2010-11-17arm: update mach-typesMian Yousaf Kaukab
To get numbers for 5500 machines and official SVP8500 numbers. ST-Ericsson ID: ER280045 mach-types are equivalent to the following patch: ST-Ericsson ID: AP279856 Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Change-Id: I0ce5ce2c31cc3e35fadd01acc20f077992be2f0d Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/8775 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-11-17Add qsort - add support for sorting data arraysMichael Brandt
Code adapted from uClibc-0.9.30.3 Originated from U-Boot mainline git://git.denx.de/u-boot.git commit 54c6977e9ca41fb38b45f1746d90f2806be3b5cb Original committer Wolfgang Denk <wd@denx.de> Change-Id: I85a11005af9eaed50d94674fdac74a32f7bc4f35 Signed-off-by: Michael Brandt <michael.brandt@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/8439 Reviewed-by: Mikael LARSSON1 <mikael.xt.larsson@stericsson.com> Tested-by: Mikael LARSSON1 <mikael.xt.larsson@stericsson.com>
2010-11-12U8500: Load splash image from TOCMikael Larsson
This patch removes splash image from u-boot binary and loads it from a toc entry called SPLASH instead. Depends-On: I2e182df7fa056a5df2deb05a4ebab844eedbb85d I715045aba01c1c747f9bd15f02c6d057f66ff968 I93e63a092fd6f229f530e55ec4b98e8e09db1c06 ST-Ericsson ID: ER268766 Change-Id: I4ee7885618d18d526dfca55d7c45b769cd9b52c9 Signed-off-by: Mikael Larsson <mikael.xt.larsson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/6879 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Rikard OLSSON <rikard.p.olsson@stericsson.com>
2010-11-08Rework env_emmcSebastian Rasmussen
Use TOC functionality instead of hardcoded environment addresses to make it easier to move the U-boot environment configuration to other locations in the flash memory. ST-Ericsson ID: 270847 ST-Ericsson FOSS-OUT ID: STETL-FOSS-OUT-10009 Change-Id: If70d56587d47afdc60a2e50e85d0de13cdf556cc Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7761 Reviewed-by: Simon SJOLANDER <simon.sjolander@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Patrik RYD <patrik.ryd@stericsson.com> Reviewed-by: Mikael GULLBERG <mikael.xx.gullberg@stericsson.com> Tested-by: Patrik RYD <patrik.ryd@stericsson.com>
2010-11-04Generic toc loadingMikael Larsson
Adds generic toc loading so not all toc clients need to implement their own toc loader. ST-Ericsson ID: ER268766 Change-Id: Ib3b69df700a5167115aeb168006c24b76c39763f Signed-off-by: Mikael Larsson <mikael.xt.larsson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/6869 Reviewed-by: Sebastian RASMUSSEN <sebastian.rasmussen@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-11-04U8500: Add support for SPIMarkus Helgesson
Added SPI support for U8500 ST-Ericsson ID: 269867 ST-Ericsson FOSS-OUT ID: STETL-FOSS-OUT-10121 Change-Id: Ied17dd39aa1ebc0ee95818c59c7f211ce655b8bf Signed-off-by: Markus Helgesson <markus.helgesson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7569 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-11-01U8500: Fix modem loading for V2Mikael Larsson
This fixes the broken modem loading in V2. ST-Ericsson ID: ER277406 Change-Id: Ifefe85d0cbeaa5c5e6dca3afe57f371530bc646a Signed-off-by: Mikael Larsson <mikael.xt.larsson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7551 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-10-28U-Boot: Modify memargs512 pmem_hwb to 128MBMisbah
Change pmem_hwb from 64MB to 128MB. This makes it possible to record upto 1080p video content. ST-Ericsson Change ID: 271474 Change-Id: I6e63c7063f188b9ba72c7d7b8c87ad92bee2d696 Change-Id: I54d6ca8d03682dfe9f3492ef315eef308aa4392c Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/5778 Reviewed-by: Vishal JAIN <v.jain@stericsson.com> Tested-by: Vishal JAIN <v.jain@stericsson.com> Reviewed-by: Henrik CARLING <henrik.carling@stericsson.com>
2010-10-27U8500: Disable itp and modem loadingMikael Larsson
itp and modem laoding causes V2 HW to hang in u-boot This disables that functionality ST-Ericsson ID: ER277406 Change-Id: Ia1ec09dadca813ff46775453dea64e6a1b69af07 Signed-off-by: Mikael Larsson <mikael.xt.larsson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/7262 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Michael BRANDT <michael.brandt@stericsson.com> Tested-by: Tobias ANDERSON <tobias.xx.andersson@stericsson.com>
2010-10-26U8500: default env: MMC related fixes and changesMichael Brandt
Enabled setexpr command to enable $filesize to $blocksize conversion in scripts. Changed occurrences of "mmc init" to "mmc rescan". Changed paths in fat commands to absolute paths. Added mmcboot alias to boot from external MMC (SD card). The rootfs must be on the second partition. This allows to have a FAT FS on the first partition; which is very common. Change-Id: I17b89a43b4be7906f3f9e16e9ced9fa421a52d3a Signed-off-by: Michael Brandt <michael.brandt@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/6964 Reviewed-by: Robert ROSENGREN <robert.rosengren@stericsson.com> Reviewed-by: Kunal GOEL <kunal.goel@stericsson.com>
2010-10-15Add correct position of hwmem in memargs512Robert Fekete
The reason UI gets sluggish, among other weird graphics issues is that B2R2 cannot address memory that spans over a 64MB boundary. Hwmem memory is used by B2R2. The old position 28M@172 (172 - 200MB, 192 is at a 64M boundary) unfortunalelly still spans over a 64MB boundary. Therefore it is crucial that hwmem is moved to an appropriate position. hwmem=32M@128M mem=64M@160M aligns perfectly and empty memory slots is given to mem, thus no decrease in system memory at all. ST-Ericsson Change ID: ER272332 Change-Id: I5b84ca1a0acfb9f03c00d1733b8dd3cbcab0503f Signed-off-by: Robert Fekete <robert.fekete@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/6571 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Nils CALMSUND <nils.calmsund@stericsson.com> Reviewed-by: Fredrik ALLANSSON <fredrik.allansson@stericsson.com>
2010-10-12u8500: Changed rootdelay=1 to rootwaitJonas Aaberg
Wait until for the device with root filesytem appears. (No matter if it takes 0s or 2h.) The result of this patch 1s faster boot. Change-Id: I1b0257bcde10da568ad50d6fc601759bc9823ed3 Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Change-Id: Ic16cd6a44443ab73f92cdd94aebc7395ec861aeb Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/5811 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-09-28ITP loadingMikael Larsson
This adds functionality to load and execute ITP in an early stage just after eMMC init. eMMC init was moved to mmc_host.c since it fits better there and is needed in order to access ITP before loading env. Flag for functionality is CONFIG_ITP_LOAD. This functionailty depends on CONFIG_TOC_PARTITION ST-Ericsson ID: ER273744 Change-Id: Ia80f0bf2d67055045c95e47473b9ba2275bbdb83 Signed-off-by: Mikael LARSSON <mikael.xt.larsson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/5130 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
2010-09-28Added output env var Size and Offset in tocload commandPeter Nessrup
tocentrysize and tocentryoffset are now output as env vars from the tocload command Change-Id: I3fe3918c48bb6ab196100d4cc617569a829803c6 Signed-off-by: Peter Nessrup <peter.nessrup@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/5673 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Sebastian RASMUSSEN <sebastian.rasmussen@stericsson.com> Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
2010-09-24u-boot: Changed pmem to hwmem in bootargsFredrik Allansson
The reserved memory for pmem has been changed to reserved memory for hwmem. ST-Ericsson ID: WP269630 Change-Id: I0eff03561e12b286d983efe67d39a265bf647d45 Signed-off-by: Fredrik Allansson <fredrik.allansson@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/5401 Reviewed-by: Johan MOSSBERG <johan.xx.mossberg@stericsson.com> Reviewed-by: Robert LIND <robert.lind@stericsson.com> Reviewed-by: Robert FEKETE <robert.fekete@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-09-16boottime: Enable boot time measurements.Jonas Aaberg
This patch enables boot time measurements for u-boot. It also includes minor updates as well. Change-Id: I993c9ad4fa5dab62df2c0a88454a7546d9565d21 Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/4610 Reviewed-by: Robert ROSENGREN <robert.rosengren@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
2010-09-16Added TOC partition supportPeter Nessrup
TOC partition support added under disk New files: part_toc.c, part_toc.h CONFIG_TOC_PARTITION needs to be set for it to be activated. ST-Ericsson ID: ER256835 Change-Id: I301b0650cb73b34f04b80dd5f27babdbf7ba09e1 Signed-off-by: Peter Nessrup <peter.nessrup@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/4369 Reviewed-by: Sebastian RASMUSSEN <sebastian.rasmussen@stericsson.com> Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com> Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
2010-09-13U-Boot: Modify memargs512 pmem_hwb to 64MBRobert Fekete
Change pmem_hwb from 56MB to 64MB. This makes it possible to play 1080p video content. ST-Ericsson Change ID: ER272382 Change-Id: I72fd601c36c49ddd01b63de56f54d5f9ac02e5a6 Signed-off-by: Robert Fekete <robert.fekete@stericsson.com> Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/5001 Reviewed-by: Michael BRANDT <michael.brandt@stericsson.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-04-28 21:38:43 +0000