From 4c1883670acbf1cc83c04df1876235c3aedde128 Mon Sep 17 00:00:00 2001 From: Dirk Eibach Date: Wed, 9 Sep 2009 12:36:07 +0200 Subject: ppc4xx: Rename compactcenter to intip Signed-off-by: Dirk Eibach Signed-off-by: Stefan Roese --- MAINTAINERS | 2 +- MAKEALL | 2 +- Makefile | 16 +- board/gdsys/compactcenter/Makefile | 53 ---- board/gdsys/compactcenter/chip_config.c | 87 ------ board/gdsys/compactcenter/compactcenter.c | 289 -------------------- board/gdsys/compactcenter/config.mk | 41 --- board/gdsys/compactcenter/init.S | 97 ------- board/gdsys/compactcenter/u-boot.lds | 144 ---------- board/gdsys/intip/Makefile | 53 ++++ board/gdsys/intip/chip_config.c | 87 ++++++ board/gdsys/intip/config.mk | 41 +++ board/gdsys/intip/init.S | 97 +++++++ board/gdsys/intip/intip.c | 289 ++++++++++++++++++++ board/gdsys/intip/u-boot.lds | 144 ++++++++++ include/configs/compactcenter.h | 437 ------------------------------ include/configs/intip.h | 437 ++++++++++++++++++++++++++++++ 17 files changed, 1158 insertions(+), 1158 deletions(-) delete mode 100644 board/gdsys/compactcenter/Makefile delete mode 100644 board/gdsys/compactcenter/chip_config.c delete mode 100644 board/gdsys/compactcenter/compactcenter.c delete mode 100644 board/gdsys/compactcenter/config.mk delete mode 100644 board/gdsys/compactcenter/init.S delete mode 100644 board/gdsys/compactcenter/u-boot.lds create mode 100644 board/gdsys/intip/Makefile create mode 100644 board/gdsys/intip/chip_config.c create mode 100644 board/gdsys/intip/config.mk create mode 100644 board/gdsys/intip/init.S create mode 100644 board/gdsys/intip/intip.c create mode 100644 board/gdsys/intip/u-boot.lds delete mode 100644 include/configs/compactcenter.h create mode 100644 include/configs/intip.h diff --git a/MAINTAINERS b/MAINTAINERS index e9db27842..e0d4786a7 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -141,10 +141,10 @@ Jon Diekema Dirk Eibach - compactcenter PPC460EX devconcenter PPC460EX dlvision PPC405EP gdppc440etx PPC440EP/GR + intip PPC460EX neo PPC405EP Dave Ellis diff --git a/MAKEALL b/MAKEALL index f0ed8ea87..b3d35ac05 100755 --- a/MAKEALL +++ b/MAKEALL @@ -185,7 +185,6 @@ LIST_4xx=" \ canyonlands \ canyonlands_nand \ CMS700 \ - compactcenter \ CPCI2DP \ CPCI405 \ CPCI4052 \ @@ -214,6 +213,7 @@ LIST_4xx=" \ hcu5 \ HH405 \ HUB405 \ + intip \ JSE \ KAREF \ katmai \ diff --git a/Makefile b/Makefile index 9764cea89..e8c90a2f2 100644 --- a/Makefile +++ b/Makefile @@ -1308,14 +1308,6 @@ CATcenter_33_config: unconfig CMS700_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx cms700 esd -# Compact-Center & DevCon-Center use different U-Boot images -compactcenter_config \ -devconcenter_config: unconfig - @mkdir -p $(obj)include - @echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \ - tr '[:lower:]' '[:upper:]')" >$(obj)include/config.h - @$(MKCONFIG) -n $@ -a compactcenter ppc ppc4xx compactcenter gdsys - CPCI2DP_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx cpci2dp esd @@ -1400,6 +1392,14 @@ HH405_config: unconfig HUB405_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx hub405 esd +# Compact-Center(codename intip) & DevCon-Center use different U-Boot images +intip_config \ +devconcenter_config: unconfig + @mkdir -p $(obj)include + @echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \ + tr '[:lower:]' '[:upper:]')" >$(obj)include/config.h + @$(MKCONFIG) -n $@ -a intip ppc ppc4xx intip gdsys + JSE_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx jse diff --git a/board/gdsys/compactcenter/Makefile b/board/gdsys/compactcenter/Makefile deleted file mode 100644 index 12f8a642e..000000000 --- a/board/gdsys/compactcenter/Makefile +++ /dev/null @@ -1,53 +0,0 @@ -# -# (C) Copyright 2008 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(BOARD).a - -COBJS-y := $(BOARD).o -COBJS-$(CONFIG_CMD_CHIP_CONFIG) += chip_config.o -SOBJS := init.o - -COBJS := $(COBJS-y) -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(OBJS) $(SOBJS) - $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) - -clean: - rm -f $(SOBJS) $(OBJS) - -distclean: clean - rm -f $(LIB) core *.bak $(obj).depend - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/board/gdsys/compactcenter/chip_config.c b/board/gdsys/compactcenter/chip_config.c deleted file mode 100644 index e46f4d8ec..000000000 --- a/board/gdsys/compactcenter/chip_config.c +++ /dev/null @@ -1,87 +0,0 @@ -/* - * (C) Copyright 2008-2009 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - * - */ - -#include -#include - -struct ppc4xx_config ppc4xx_config_val[] = { - { - "600-nor", "NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100", - { - 0x86, 0x80, 0xce, 0x1f, 0x79, 0x80, 0x00, 0xa0, - 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 - } - }, - { - "600-nand", "NAND CPU: 600 PLB: 200 OPB: 100 EBC: 100", - { - 0x86, 0x80, 0xce, 0x1f, 0x79, 0x90, 0x01, 0xa0, - 0xa0, 0xe8, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00 - } - }, - { - "800-nor", "NOR CPU: 800 PLB: 200 OPB: 100 EBC: 100", - { - 0x86, 0x80, 0xba, 0x14, 0x99, 0x80, 0x00, 0xa0, - 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 - } - }, - { - "800-nand", "NAND CPU: 800 PLB: 200 OPB: 100 EBC: 100", - { - 0x86, 0x80, 0xba, 0x14, 0x99, 0x90, 0x01, 0xa0, - 0xa0, 0xe8, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00 - } - }, - { - "1000-nor", "NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100", - { - 0x86, 0x82, 0x96, 0x19, 0xb9, 0x80, 0x00, 0xa0, - 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 - } - }, - { - "1000-nand", "NAND CPU:1000 PLB: 200 OPB: 100 EBC: 100", - { - 0x86, 0x82, 0x96, 0x19, 0xb9, 0x90, 0x01, 0xa0, - 0xa0, 0xe8, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00 - } - }, - { - "1066-nor", "NOR CPU:1066 PLB: 266 OPB: 88 EBC: 88", - { - 0x86, 0x80, 0xb3, 0x01, 0x9d, 0x80, 0x00, 0xa0, - 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 - } - }, - { - "1066-nand", "NAND CPU:1066 PLB: 266 OPB: 88 EBC: 88", - { - 0x86, 0x80, 0xb3, 0x01, 0x9d, 0x90, 0x01, 0xa0, - 0xa0, 0xe8, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00 - } - }, -}; - -int ppc4xx_config_count = ARRAY_SIZE(ppc4xx_config_val); diff --git a/board/gdsys/compactcenter/compactcenter.c b/board/gdsys/compactcenter/compactcenter.c deleted file mode 100644 index 8a5ea300d..000000000 --- a/board/gdsys/compactcenter/compactcenter.c +++ /dev/null @@ -1,289 +0,0 @@ -/* - * (C) Copyright 2009 - * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de - * - * Based on board/amcc/canyonlands/canyonlands.c - * (C) Copyright 2008 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; - -DECLARE_GLOBAL_DATA_PTR; - -#define CONFIG_SYS_BCSR3_PCIE 0x10 - -int board_early_init_f(void) -{ - /* - * Setup the interrupt controller polarities, triggers, etc. - */ - mtdcr(uic0sr, 0xffffffff); /* clear all */ - mtdcr(uic0er, 0x00000000); /* disable all */ - mtdcr(uic0cr, 0x00000005); /* ATI & UIC1 crit are critical */ - mtdcr(uic0pr, 0xffffffff); /* per ref-board manual */ - mtdcr(uic0tr, 0x00000000); /* per ref-board manual */ - mtdcr(uic0vr, 0x00000000); /* int31 highest, base=0x000 */ - mtdcr(uic0sr, 0xffffffff); /* clear all */ - - mtdcr(uic1sr, 0xffffffff); /* clear all */ - mtdcr(uic1er, 0x00000000); /* disable all */ - mtdcr(uic1cr, 0x00000000); /* all non-critical */ - mtdcr(uic1pr, 0xffffffff); /* per ref-board manual */ - mtdcr(uic1tr, 0x00000000); /* per ref-board manual */ - mtdcr(uic1vr, 0x00000000); /* int31 highest, base=0x000 */ - mtdcr(uic1sr, 0xffffffff); /* clear all */ - - mtdcr(uic2sr, 0xffffffff); /* clear all */ - mtdcr(uic2er, 0x00000000); /* disable all */ - mtdcr(uic2cr, 0x00000000); /* all non-critical */ - mtdcr(uic2pr, 0xffffffff); /* per ref-board manual */ - mtdcr(uic2tr, 0x00000000); /* per ref-board manual */ - mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */ - mtdcr(uic2sr, 0xffffffff); /* clear all */ - - mtdcr(uic3sr, 0xffffffff); /* clear all */ - mtdcr(uic3er, 0x00000000); /* disable all */ - mtdcr(uic3cr, 0x00000000); /* all non-critical */ - mtdcr(uic3pr, 0xffffffff); /* per ref-board manual */ - mtdcr(uic3tr, 0x00000000); /* per ref-board manual */ - mtdcr(uic3vr, 0x00000000); /* int31 highest, base=0x000 */ - mtdcr(uic3sr, 0xffffffff); /* clear all */ - - /* - * Configure PFC (Pin Function Control) registers - * enable GPIO 49-63 - * UART0: 4 pins - */ - mtsdr(SDR0_PFC0, 0x00007fff); - mtsdr(SDR0_PFC1, 0x00040000); - - /* Enable PCI host functionality in SDR0_PCI0 */ - mtsdr(SDR0_PCI0, 0xe0000000); - - mtsdr(SDR0_SRST1, 0); /* Pull AHB out of reset default=1 */ - - /* Setup PLB4-AHB bridge based on the system address map */ - mtdcr(AHB_TOP, 0x8000004B); - mtdcr(AHB_BOT, 0x8000004B); - - /* - * Configure USB-STP pins as alternate and not GPIO - * It seems to be neccessary to configure the STP pins as GPIO - * input at powerup (perhaps while USB reset is asserted). So - * we configure those pins to their "real" function now. - */ - gpio_config(16, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); - gpio_config(19, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); - - /* Trigger board component reset */ - out_le16((void *)CONFIG_SYS_IO_BASE, 0xffff); - out_le16((void *)CONFIG_SYS_IO_BASE + 0x100, 0xffff); - udelay(50); - out_le16((void *)CONFIG_SYS_IO_BASE, 0xffbf); - out_le16((void *)CONFIG_SYS_IO_BASE + 0x100, 0xffbf); - udelay(50); - out_le16((void *)CONFIG_SYS_IO_BASE, 0xffff); - out_le16((void *)CONFIG_SYS_IO_BASE + 0x100, 0xffff); - - return 0; -} - -int get_cpu_num(void) -{ - int cpu = NA_OR_UNKNOWN_CPU; - - return cpu; -} - -int checkboard(void) -{ - char *s = getenv("serial#"); - -#ifdef CONFIG_DEVCONCENTER - printf("Board: DevCon-Center"); -#else - printf("Board: CompactCenter"); -#endif - - if (s != NULL) { - puts(", serial# "); - puts(s); - } - putc('\n'); - - return 0; -} - -/* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - */ -#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller *hose) -{ - /* - * Disable everything - */ - out_le32((void *)PCIX0_PIM0SA, 0); /* disable */ - out_le32((void *)PCIX0_PIM1SA, 0); /* disable */ - out_le32((void *)PCIX0_PIM2SA, 0); /* disable */ - out_le32((void *)PCIX0_EROMBA, 0); /* disable expansion rom */ - - /* - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 - * strapping options to not support sizes such as 128/256 MB. - */ - out_le32((void *)PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE); - out_le32((void *)PCIX0_PIM0LAH, 0); - out_le32((void *)PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1); - out_le32((void *)PCIX0_BAR0, 0); - - /* - * Program the board's subsystem id/vendor id - */ - out_le16((void *)PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID); - out_le16((void *)PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID); - - out_le16((void *)PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY); -} -#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ - -#if defined(CONFIG_PCI) -/* - * is_pci_host - * - * This routine is called to determine if a pci scan should be - * performed. With various hardware environments (especially cPCI and - * PPMC) it's insufficient to depend on the state of the arbiter enable - * bit in the strap register, or generic host/adapter assumptions. - * - * Rather than hard-code a bad assumption in the general 440 code, the - * 440 pci code requires the board to decide at runtime. - * - * Return 0 for adapter mode, non-zero for host (monarch) mode. - */ -int is_pci_host(struct pci_controller *hose) -{ - /* Board is always configured as host. */ - return 1; -} -#endif /* CONFIG_PCI */ - -int board_early_init_r(void) -{ - /* - * CompactCenter has 64MBytes, DevCon-Center 128MBytes of NOR FLASH - * (Spansion 29GL512), but the boot EBC mapping only supports a maximum - * of 16MBytes (4.ff00.0000 - 4.ffff.ffff). - * To solve this problem, the FLASH has to get remapped to another - * EBC address which accepts bigger regions: - * - * 0xfn00.0000 -> 4.cn00.0000 - */ - - u32 bxcr_bw = (CONFIG_SYS_FLASH_SIZE == 128 << 20) ? - EBC_BXCR_BS_128MB : EBC_BXCR_BS_64MB; - - /* Remap the NOR FLASH to 0xcn00.0000 ... 0xcfff.ffff */ - mtebc(PB0CR, CONFIG_SYS_FLASH_BASE_PHYS_L - | bxcr_bw - | EBC_BXCR_BU_RW - | EBC_BXCR_BW_16BIT); - - /* Remove TLB entry of boot EBC mapping */ - remove_tlb(CONFIG_SYS_BOOT_BASE_ADDR, 16 << 20); - - /* Add TLB entry for 0xfn00.0000 -> 0x4.cn00.0000 */ - program_tlb(CONFIG_SYS_FLASH_BASE_PHYS, CONFIG_SYS_FLASH_BASE, - CONFIG_SYS_FLASH_SIZE, TLB_WORD2_I_ENABLE); - - /* - * Now accessing of the whole 64Mbytes of NOR FLASH at virtual address - * 0xfc00.0000 is possible - */ - - /* - * Clear potential errors resulting from auto-calibration. - * If not done, then we could get an interrupt later on when - * exceptions are enabled. - */ - set_mcsr(get_mcsr()); - - return 0; -} - -int misc_init_r(void) -{ - u32 sdr0_srst1 = 0; - u32 eth_cfg; - - /* - * Set EMAC mode/configuration (GMII, SGMII, RGMII...). - * This is board specific, so let's do it here. - */ - mfsdr(SDR0_ETH_CFG, eth_cfg); - /* disable SGMII mode */ - eth_cfg &= ~(SDR0_ETH_CFG_SGMII2_ENABLE | - SDR0_ETH_CFG_SGMII1_ENABLE | - SDR0_ETH_CFG_SGMII0_ENABLE); - /* Set the for 2 RGMII mode */ - /* GMC0 EMAC4_0, GMC0 EMAC4_1, RGMII Bridge 0 */ - eth_cfg &= ~SDR0_ETH_CFG_GMC0_BRIDGE_SEL; - eth_cfg |= SDR0_ETH_CFG_GMC1_BRIDGE_SEL; - mtsdr(SDR0_ETH_CFG, eth_cfg); - - /* - * The AHB Bridge core is held in reset after power-on or reset - * so enable it now - */ - mfsdr(SDR0_SRST1, sdr0_srst1); - sdr0_srst1 &= ~SDR0_SRST1_AHB; - mtsdr(SDR0_SRST1, sdr0_srst1); - - return 0; -} - -#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) -extern void __ft_board_setup(void *blob, bd_t *bd); - -void ft_board_setup(void *blob, bd_t *bd) -{ - __ft_board_setup(blob, bd); - - fdt_find_and_setprop(blob, "/plb/pciex@d00000000", "status", - "disabled", sizeof("disabled"), 1); - - fdt_find_and_setprop(blob, "/plb/sata@bffd1000", "status", - "disabled", sizeof("disabled"), 1); -} -#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/board/gdsys/compactcenter/config.mk b/board/gdsys/compactcenter/config.mk deleted file mode 100644 index 56e397d77..000000000 --- a/board/gdsys/compactcenter/config.mk +++ /dev/null @@ -1,41 +0,0 @@ -# -# (C) Copyright 2008 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# -# -# G&D CompactCenter -# - -sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp - -ifndef TEXT_BASE -TEXT_BASE = 0xFFFA0000 -endif - -PLATFORM_CPPFLAGS += -DCONFIG_440=1 - -ifeq ($(debug),1) -PLATFORM_CPPFLAGS += -DDEBUG -endif - -ifeq ($(dbcr),1) -PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 -endif diff --git a/board/gdsys/compactcenter/init.S b/board/gdsys/compactcenter/init.S deleted file mode 100644 index e205c9d7e..000000000 --- a/board/gdsys/compactcenter/init.S +++ /dev/null @@ -1,97 +0,0 @@ -/* - * (C) Copyright 2009 - * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de - * - * Based on board/amcc/canyonlands/init.S - * (C) Copyright 2008 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include - -/************************************************************************** - * TLB TABLE - * - * This table is used by the cpu boot code to setup the initial tlb - * entries. Rather than make broad assumptions in the cpu source tree, - * this table lets each board set things up however they like. - * - * Pointer to the table is returned in r1 - * - *************************************************************************/ - .section .bootpg,"ax" - .globl tlbtab - -tlbtab: - tlbtab_start - - /* - * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to - * use the speed up boot process. It is patched after relocation to - * enable SA_I - */ - tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_16M, CONFIG_SYS_BOOT_BASE_ADDR, - 4, AC_R|AC_W|AC_X|SA_G) /* TLB 0 */ - - /* - * TLB entries for SDRAM are not needed on this platform. - * They are dynamically generated in the SPD DDR(2) detection - * routine. - */ - -#ifdef CONFIG_SYS_INIT_RAM_DCACHE - /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ - tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, - 0, AC_R|AC_W|AC_X|SA_G) -#endif - - tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 0xC, - AC_R|AC_W|SA_G|SA_I) - tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x20000000, 0xC, - AC_R|AC_W|SA_G|SA_I) - - /* TLB-entry for NVRAM */ - tlbentry(CONFIG_SYS_NVRAM_BASE, SZ_1M, CONFIG_SYS_NVRAM_BASE, 4, - AC_R|AC_W|SA_G|SA_I) - - /* TLB-entry for UART */ - tlbentry(CONFIG_SYS_UART_BASE, SZ_16K, CONFIG_SYS_UART_BASE, 4, - AC_R|AC_W|SA_G|SA_I) - - /* TLB-entry for IO */ - tlbentry(CONFIG_SYS_IO_BASE, SZ_16K, CONFIG_SYS_IO_BASE, 4, - AC_R|AC_W|SA_G|SA_I) - - /* TLB-entry for OCM */ - tlbentry(CONFIG_SYS_OCM_BASE, SZ_1M, 0x00000000, 4, - AC_R|AC_W|AC_X|SA_I) - - /* TLB-entry for Local Configuration registers => peripherals */ - tlbentry(CONFIG_SYS_LOCAL_CONF_REGS, SZ_16M, CONFIG_SYS_LOCAL_CONF_REGS, - 4, AC_R|AC_W|AC_X|SA_G|SA_I) - - /* AHB: Internal USB Peripherals (USB, SATA) */ - tlbentry(CONFIG_SYS_AHB_BASE, SZ_1M, 0xbff00000, 4, - AC_R|AC_W|AC_X|SA_G|SA_I) - - tlbtab_end diff --git a/board/gdsys/compactcenter/u-boot.lds b/board/gdsys/compactcenter/u-boot.lds deleted file mode 100644 index 0c95d5c29..000000000 --- a/board/gdsys/compactcenter/u-boot.lds +++ /dev/null @@ -1,144 +0,0 @@ -/* - * (C) Copyright 2008 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -OUTPUT_ARCH(powerpc) -/* Do we need any of these for elf? - __DYNAMIC = 0; */ -SECTIONS -{ - .resetvec 0xFFFFFFFC : - { - *(.resetvec) - } = 0xffff - - .bootpg 0xFFFFF000 : - { - cpu/ppc4xx/start.o (.bootpg) - } = 0xffff - - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .interp : { *(.interp) } - .hash : { *(.hash) } - .dynsym : { *(.dynsym) } - .dynstr : { *(.dynstr) } - .rel.text : { *(.rel.text) } - .rela.text : { *(.rela.text) } - .rel.data : { *(.rel.data) } - .rela.data : { *(.rela.data) } - .rel.rodata : { *(.rel.rodata) } - .rela.rodata : { *(.rela.rodata) } - .rel.got : { *(.rel.got) } - .rela.got : { *(.rela.got) } - .rel.ctors : { *(.rel.ctors) } - .rela.ctors : { *(.rela.ctors) } - .rel.dtors : { *(.rel.dtors) } - .rela.dtors : { *(.rela.dtors) } - .rel.bss : { *(.rel.bss) } - .rela.bss : { *(.rela.bss) } - .rel.plt : { *(.rel.plt) } - .rela.plt : { *(.rela.plt) } - .init : { *(.init) } - .plt : { *(.plt) } - .text : - { - /* WARNING - the following is hand-optimized to fit within */ - /* the sector layout of our flash chips! XXX FIXME XXX */ - - cpu/ppc4xx/start.o (.text) - board/gdsys/compactcenter/init.o (.text) - - *(.text) - *(.fixup) - *(.got1) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(.rodata) - *(.rodata1) - *(.rodata.str1.4) - } - .fini : { *(.fini) } =0 - .ctors : { *(.ctors) } - .dtors : { *(.dtors) } - - /* Read-write section, merged into data segment: */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - *(.got) - _GOT2_TABLE_ = .; - *(.got2) - _FIXUP_TABLE_ = .; - *(.fixup) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data : - { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.dynamic) - CONSTRUCTORS - } - _edata = .; - PROVIDE (edata = .); - - . = .; - __u_boot_cmd_start = .; - .u_boot_cmd : { *(.u_boot_cmd) } - __u_boot_cmd_end = .; - - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) *(.scommon) - *(.dynbss) - *(.bss) - *(COMMON) - . = ALIGN(4); - } - - _end = . ; - PROVIDE (end = .); -} diff --git a/board/gdsys/intip/Makefile b/board/gdsys/intip/Makefile new file mode 100644 index 000000000..12f8a642e --- /dev/null +++ b/board/gdsys/intip/Makefile @@ -0,0 +1,53 @@ +# +# (C) Copyright 2008 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y := $(BOARD).o +COBJS-$(CONFIG_CMD_CHIP_CONFIG) += chip_config.o +SOBJS := init.o + +COBJS := $(COBJS-y) +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/gdsys/intip/chip_config.c b/board/gdsys/intip/chip_config.c new file mode 100644 index 000000000..e46f4d8ec --- /dev/null +++ b/board/gdsys/intip/chip_config.c @@ -0,0 +1,87 @@ +/* + * (C) Copyright 2008-2009 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include +#include + +struct ppc4xx_config ppc4xx_config_val[] = { + { + "600-nor", "NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100", + { + 0x86, 0x80, 0xce, 0x1f, 0x79, 0x80, 0x00, 0xa0, + 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 + } + }, + { + "600-nand", "NAND CPU: 600 PLB: 200 OPB: 100 EBC: 100", + { + 0x86, 0x80, 0xce, 0x1f, 0x79, 0x90, 0x01, 0xa0, + 0xa0, 0xe8, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00 + } + }, + { + "800-nor", "NOR CPU: 800 PLB: 200 OPB: 100 EBC: 100", + { + 0x86, 0x80, 0xba, 0x14, 0x99, 0x80, 0x00, 0xa0, + 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 + } + }, + { + "800-nand", "NAND CPU: 800 PLB: 200 OPB: 100 EBC: 100", + { + 0x86, 0x80, 0xba, 0x14, 0x99, 0x90, 0x01, 0xa0, + 0xa0, 0xe8, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00 + } + }, + { + "1000-nor", "NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100", + { + 0x86, 0x82, 0x96, 0x19, 0xb9, 0x80, 0x00, 0xa0, + 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 + } + }, + { + "1000-nand", "NAND CPU:1000 PLB: 200 OPB: 100 EBC: 100", + { + 0x86, 0x82, 0x96, 0x19, 0xb9, 0x90, 0x01, 0xa0, + 0xa0, 0xe8, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00 + } + }, + { + "1066-nor", "NOR CPU:1066 PLB: 266 OPB: 88 EBC: 88", + { + 0x86, 0x80, 0xb3, 0x01, 0x9d, 0x80, 0x00, 0xa0, + 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00 + } + }, + { + "1066-nand", "NAND CPU:1066 PLB: 266 OPB: 88 EBC: 88", + { + 0x86, 0x80, 0xb3, 0x01, 0x9d, 0x90, 0x01, 0xa0, + 0xa0, 0xe8, 0x23, 0x58, 0x0d, 0x05, 0x00, 0x00 + } + }, +}; + +int ppc4xx_config_count = ARRAY_SIZE(ppc4xx_config_val); diff --git a/board/gdsys/intip/config.mk b/board/gdsys/intip/config.mk new file mode 100644 index 000000000..56e397d77 --- /dev/null +++ b/board/gdsys/intip/config.mk @@ -0,0 +1,41 @@ +# +# (C) Copyright 2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# +# G&D CompactCenter +# + +sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp + +ifndef TEXT_BASE +TEXT_BASE = 0xFFFA0000 +endif + +PLATFORM_CPPFLAGS += -DCONFIG_440=1 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif + +ifeq ($(dbcr),1) +PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 +endif diff --git a/board/gdsys/intip/init.S b/board/gdsys/intip/init.S new file mode 100644 index 000000000..e205c9d7e --- /dev/null +++ b/board/gdsys/intip/init.S @@ -0,0 +1,97 @@ +/* + * (C) Copyright 2009 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * Based on board/amcc/canyonlands/init.S + * (C) Copyright 2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/************************************************************************** + * TLB TABLE + * + * This table is used by the cpu boot code to setup the initial tlb + * entries. Rather than make broad assumptions in the cpu source tree, + * this table lets each board set things up however they like. + * + * Pointer to the table is returned in r1 + * + *************************************************************************/ + .section .bootpg,"ax" + .globl tlbtab + +tlbtab: + tlbtab_start + + /* + * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to + * use the speed up boot process. It is patched after relocation to + * enable SA_I + */ + tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_16M, CONFIG_SYS_BOOT_BASE_ADDR, + 4, AC_R|AC_W|AC_X|SA_G) /* TLB 0 */ + + /* + * TLB entries for SDRAM are not needed on this platform. + * They are dynamically generated in the SPD DDR(2) detection + * routine. + */ + +#ifdef CONFIG_SYS_INIT_RAM_DCACHE + /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ + tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, + 0, AC_R|AC_W|AC_X|SA_G) +#endif + + tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 0xC, + AC_R|AC_W|SA_G|SA_I) + tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x20000000, 0xC, + AC_R|AC_W|SA_G|SA_I) + + /* TLB-entry for NVRAM */ + tlbentry(CONFIG_SYS_NVRAM_BASE, SZ_1M, CONFIG_SYS_NVRAM_BASE, 4, + AC_R|AC_W|SA_G|SA_I) + + /* TLB-entry for UART */ + tlbentry(CONFIG_SYS_UART_BASE, SZ_16K, CONFIG_SYS_UART_BASE, 4, + AC_R|AC_W|SA_G|SA_I) + + /* TLB-entry for IO */ + tlbentry(CONFIG_SYS_IO_BASE, SZ_16K, CONFIG_SYS_IO_BASE, 4, + AC_R|AC_W|SA_G|SA_I) + + /* TLB-entry for OCM */ + tlbentry(CONFIG_SYS_OCM_BASE, SZ_1M, 0x00000000, 4, + AC_R|AC_W|AC_X|SA_I) + + /* TLB-entry for Local Configuration registers => peripherals */ + tlbentry(CONFIG_SYS_LOCAL_CONF_REGS, SZ_16M, CONFIG_SYS_LOCAL_CONF_REGS, + 4, AC_R|AC_W|AC_X|SA_G|SA_I) + + /* AHB: Internal USB Peripherals (USB, SATA) */ + tlbentry(CONFIG_SYS_AHB_BASE, SZ_1M, 0xbff00000, 4, + AC_R|AC_W|AC_X|SA_G|SA_I) + + tlbtab_end diff --git a/board/gdsys/intip/intip.c b/board/gdsys/intip/intip.c new file mode 100644 index 000000000..0de1be857 --- /dev/null +++ b/board/gdsys/intip/intip.c @@ -0,0 +1,289 @@ +/* + * (C) Copyright 2009 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * Based on board/amcc/canyonlands/canyonlands.c + * (C) Copyright 2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; + +DECLARE_GLOBAL_DATA_PTR; + +#define CONFIG_SYS_BCSR3_PCIE 0x10 + +int board_early_init_f(void) +{ + /* + * Setup the interrupt controller polarities, triggers, etc. + */ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + mtdcr(uic0er, 0x00000000); /* disable all */ + mtdcr(uic0cr, 0x00000005); /* ATI & UIC1 crit are critical */ + mtdcr(uic0pr, 0xffffffff); /* per ref-board manual */ + mtdcr(uic0tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic0vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + + mtdcr(uic1sr, 0xffffffff); /* clear all */ + mtdcr(uic1er, 0x00000000); /* disable all */ + mtdcr(uic1cr, 0x00000000); /* all non-critical */ + mtdcr(uic1pr, 0xffffffff); /* per ref-board manual */ + mtdcr(uic1tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic1vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic1sr, 0xffffffff); /* clear all */ + + mtdcr(uic2sr, 0xffffffff); /* clear all */ + mtdcr(uic2er, 0x00000000); /* disable all */ + mtdcr(uic2cr, 0x00000000); /* all non-critical */ + mtdcr(uic2pr, 0xffffffff); /* per ref-board manual */ + mtdcr(uic2tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic2sr, 0xffffffff); /* clear all */ + + mtdcr(uic3sr, 0xffffffff); /* clear all */ + mtdcr(uic3er, 0x00000000); /* disable all */ + mtdcr(uic3cr, 0x00000000); /* all non-critical */ + mtdcr(uic3pr, 0xffffffff); /* per ref-board manual */ + mtdcr(uic3tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic3vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic3sr, 0xffffffff); /* clear all */ + + /* + * Configure PFC (Pin Function Control) registers + * enable GPIO 49-63 + * UART0: 4 pins + */ + mtsdr(SDR0_PFC0, 0x00007fff); + mtsdr(SDR0_PFC1, 0x00040000); + + /* Enable PCI host functionality in SDR0_PCI0 */ + mtsdr(SDR0_PCI0, 0xe0000000); + + mtsdr(SDR0_SRST1, 0); /* Pull AHB out of reset default=1 */ + + /* Setup PLB4-AHB bridge based on the system address map */ + mtdcr(AHB_TOP, 0x8000004B); + mtdcr(AHB_BOT, 0x8000004B); + + /* + * Configure USB-STP pins as alternate and not GPIO + * It seems to be neccessary to configure the STP pins as GPIO + * input at powerup (perhaps while USB reset is asserted). So + * we configure those pins to their "real" function now. + */ + gpio_config(16, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); + gpio_config(19, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); + + /* Trigger board component reset */ + out_le16((void *)CONFIG_SYS_IO_BASE, 0xffff); + out_le16((void *)CONFIG_SYS_IO_BASE + 0x100, 0xffff); + udelay(50); + out_le16((void *)CONFIG_SYS_IO_BASE, 0xffbf); + out_le16((void *)CONFIG_SYS_IO_BASE + 0x100, 0xffbf); + udelay(50); + out_le16((void *)CONFIG_SYS_IO_BASE, 0xffff); + out_le16((void *)CONFIG_SYS_IO_BASE + 0x100, 0xffff); + + return 0; +} + +int get_cpu_num(void) +{ + int cpu = NA_OR_UNKNOWN_CPU; + + return cpu; +} + +int checkboard(void) +{ + char *s = getenv("serial#"); + +#ifdef CONFIG_DEVCONCENTER + printf("Board: DevCon-Center"); +#else + printf("Board: Intip"); +#endif + + if (s != NULL) { + puts(", serial# "); + puts(s); + } + putc('\n'); + + return 0; +} + +/* + * pci_target_init + * + * The bootstrap configuration provides default settings for the pci + * inbound map (PIM). But the bootstrap config choices are limited and + * may not be sufficient for a given board. + */ +#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) +void pci_target_init(struct pci_controller *hose) +{ + /* + * Disable everything + */ + out_le32((void *)PCIX0_PIM0SA, 0); /* disable */ + out_le32((void *)PCIX0_PIM1SA, 0); /* disable */ + out_le32((void *)PCIX0_PIM2SA, 0); /* disable */ + out_le32((void *)PCIX0_EROMBA, 0); /* disable expansion rom */ + + /* + * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 + * strapping options to not support sizes such as 128/256 MB. + */ + out_le32((void *)PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE); + out_le32((void *)PCIX0_PIM0LAH, 0); + out_le32((void *)PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1); + out_le32((void *)PCIX0_BAR0, 0); + + /* + * Program the board's subsystem id/vendor id + */ + out_le16((void *)PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID); + out_le16((void *)PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID); + + out_le16((void *)PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY); +} +#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */ + +#if defined(CONFIG_PCI) +/* + * is_pci_host + * + * This routine is called to determine if a pci scan should be + * performed. With various hardware environments (especially cPCI and + * PPMC) it's insufficient to depend on the state of the arbiter enable + * bit in the strap register, or generic host/adapter assumptions. + * + * Rather than hard-code a bad assumption in the general 440 code, the + * 440 pci code requires the board to decide at runtime. + * + * Return 0 for adapter mode, non-zero for host (monarch) mode. + */ +int is_pci_host(struct pci_controller *hose) +{ + /* Board is always configured as host. */ + return 1; +} +#endif /* CONFIG_PCI */ + +int board_early_init_r(void) +{ + /* + * CompactCenter has 64MBytes, DevCon-Center 128MBytes of NOR FLASH + * (Spansion 29GL512), but the boot EBC mapping only supports a maximum + * of 16MBytes (4.ff00.0000 - 4.ffff.ffff). + * To solve this problem, the FLASH has to get remapped to another + * EBC address which accepts bigger regions: + * + * 0xfn00.0000 -> 4.cn00.0000 + */ + + u32 bxcr_bw = (CONFIG_SYS_FLASH_SIZE == 128 << 20) ? + EBC_BXCR_BS_128MB : EBC_BXCR_BS_64MB; + + /* Remap the NOR FLASH to 0xcn00.0000 ... 0xcfff.ffff */ + mtebc(PB0CR, CONFIG_SYS_FLASH_BASE_PHYS_L + | bxcr_bw + | EBC_BXCR_BU_RW + | EBC_BXCR_BW_16BIT); + + /* Remove TLB entry of boot EBC mapping */ + remove_tlb(CONFIG_SYS_BOOT_BASE_ADDR, 16 << 20); + + /* Add TLB entry for 0xfn00.0000 -> 0x4.cn00.0000 */ + program_tlb(CONFIG_SYS_FLASH_BASE_PHYS, CONFIG_SYS_FLASH_BASE, + CONFIG_SYS_FLASH_SIZE, TLB_WORD2_I_ENABLE); + + /* + * Now accessing of the whole 64Mbytes of NOR FLASH at virtual address + * 0xfc00.0000 is possible + */ + + /* + * Clear potential errors resulting from auto-calibration. + * If not done, then we could get an interrupt later on when + * exceptions are enabled. + */ + set_mcsr(get_mcsr()); + + return 0; +} + +int misc_init_r(void) +{ + u32 sdr0_srst1 = 0; + u32 eth_cfg; + + /* + * Set EMAC mode/configuration (GMII, SGMII, RGMII...). + * This is board specific, so let's do it here. + */ + mfsdr(SDR0_ETH_CFG, eth_cfg); + /* disable SGMII mode */ + eth_cfg &= ~(SDR0_ETH_CFG_SGMII2_ENABLE | + SDR0_ETH_CFG_SGMII1_ENABLE | + SDR0_ETH_CFG_SGMII0_ENABLE); + /* Set the for 2 RGMII mode */ + /* GMC0 EMAC4_0, GMC0 EMAC4_1, RGMII Bridge 0 */ + eth_cfg &= ~SDR0_ETH_CFG_GMC0_BRIDGE_SEL; + eth_cfg |= SDR0_ETH_CFG_GMC1_BRIDGE_SEL; + mtsdr(SDR0_ETH_CFG, eth_cfg); + + /* + * The AHB Bridge core is held in reset after power-on or reset + * so enable it now + */ + mfsdr(SDR0_SRST1, sdr0_srst1); + sdr0_srst1 &= ~SDR0_SRST1_AHB; + mtsdr(SDR0_SRST1, sdr0_srst1); + + return 0; +} + +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) +extern void __ft_board_setup(void *blob, bd_t *bd); + +void ft_board_setup(void *blob, bd_t *bd) +{ + __ft_board_setup(blob, bd); + + fdt_find_and_setprop(blob, "/plb/pciex@d00000000", "status", + "disabled", sizeof("disabled"), 1); + + fdt_find_and_setprop(blob, "/plb/sata@bffd1000", "status", + "disabled", sizeof("disabled"), 1); +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/board/gdsys/intip/u-boot.lds b/board/gdsys/intip/u-boot.lds new file mode 100644 index 000000000..c1cbd1c4a --- /dev/null +++ b/board/gdsys/intip/u-boot.lds @@ -0,0 +1,144 @@ +/* + * (C) Copyright 2008 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/ppc4xx/start.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/ppc4xx/start.o (.text) + board/gdsys/intip/init.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + . = ALIGN(4); + } + + _end = . ; + PROVIDE (end = .); +} diff --git a/include/configs/compactcenter.h b/include/configs/compactcenter.h deleted file mode 100644 index f8a1bbb98..000000000 --- a/include/configs/compactcenter.h +++ /dev/null @@ -1,437 +0,0 @@ -/* - * (C) Copyright 2009 - * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de - * - * Based on include/configs/canyonlands.h - * (C) Copyright 2008 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * compactcenter.h - configuration for CompactCenter (460EX) - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -/* - * This config file is used for CompactCenter and DevCon-Center - */ -#define CONFIG_460EX 1 /* Specific PPC460EX */ -#ifdef CONFIG_DEVCONCENTER -#define CONFIG_HOSTNAME devconcenter -#define CONFIG_IDENT_STRING " devconcenter 0.02" -#else -#define CONFIG_HOSTNAME compactcenter -#define CONFIG_IDENT_STRING " compactcenter 0.02" -#endif -#define CONFIG_440 1 -#define CONFIG_4xx 1 /* ... PPC4xx family */ - -/* - * Include common defines/options for all AMCC eval boards - */ -#include "amcc-common.h" - -#define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ -#define CONFIG_BOARD_TYPES 1 /* support board types */ -#define CONFIG_FIT -#define CFG_ALT_MEMTEST - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ -#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE - -/* EBC stuff */ -#ifdef CONFIG_DEVCONCENTER /* Devcon-Center has 128 MB of flash */ -#define CONFIG_SYS_FLASH_BASE 0xF8000000 /* later mapped here */ -#define CONFIG_SYS_FLASH_SIZE (128 << 20) -#else -#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped here */ -#define CONFIG_SYS_FLASH_SIZE (64 << 20) -#endif - -#define CONFIG_SYS_NVRAM_BASE 0xE0000000 -#define CONFIG_SYS_UART_BASE 0xE0100000 -#define CONFIG_SYS_IO_BASE 0xE0200000 - -#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space */ -#define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4 -#ifdef CONFIG_DEVCONCENTER /* Devcon-Center has 128 MB of flash */ -#define CONFIG_SYS_FLASH_BASE_PHYS_L 0xC8000000 -#else -#define CONFIG_SYS_FLASH_BASE_PHYS_L 0xCC000000 -#endif -#define CONFIG_SYS_FLASH_BASE_PHYS \ - (((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) \ - | (u64)CONFIG_SYS_FLASH_BASE_PHYS_L) - -#define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 64k */ -#define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ -#define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000 - -#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal periph. */ - -#define CONFIG_SYS_AHB_BASE 0xE2000000 /* int. AHB periph. */ - -/* - * Initial RAM & stack pointer (placed in OCM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ -#define CONFIG_SYS_INIT_RAM_END (4 << 10) -#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Serial Port - */ -#undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */ - -/* - * Environment - */ -/* - * Define here the location of the environment variables (FLASH). - */ -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CONFIG_SYS_NOR_CS 0 /* NOR chip connected to CSx */ - -/* - * FLASH related - */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* Use AMD reset cmd */ - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#ifdef CONFIG_DEVCONCENTER -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* max num of sectors per chip*/ -#else -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sectors per chip*/ -#endif - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase/ms */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write/ms */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* buff'd writes (20x faster) */ -#define CONFIG_SYS_FLASH_EMPTY_INFO /* 'E' for empty sector on flinfo */ - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector*/ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif /* CONFIG_ENV_IS_IN_FLASH */ - -/* - * DDR SDRAM - */ - -#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */ - -#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ -#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */ -#undef CONFIG_PPC4xx_DDR_METHOD_A - -/* DDR1/2 SDRAM Device Control Register Data Values */ -/* Memory Queue */ -#define CONFIG_SYS_SDRAM_R0BAS 0x0000f800 -#define CONFIG_SYS_SDRAM_R1BAS 0x00000000 -#define CONFIG_SYS_SDRAM_R2BAS 0x00000000 -#define CONFIG_SYS_SDRAM_R3BAS 0x00000000 -#define CONFIG_SYS_SDRAM_PLBADDULL 0x00000000 -#define CONFIG_SYS_SDRAM_PLBADDUHB 0x00000008 -#define CONFIG_SYS_SDRAM_CONF1LL 0x80001C80 -#define CONFIG_SYS_SDRAM_CONF1HB 0x80001C80 -#define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000 - -/* SDRAM Controller */ -#define CONFIG_SYS_SDRAM0_MB0CF 0x00000201 -#define CONFIG_SYS_SDRAM0_MB1CF 0x00000000 -#define CONFIG_SYS_SDRAM0_MB2CF 0x00000000 -#define CONFIG_SYS_SDRAM0_MB3CF 0x00000000 -#define CONFIG_SYS_SDRAM0_MCOPT1 0x05122000 -#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000 -#define CONFIG_SYS_SDRAM0_MODT0 0x00000000 -#define CONFIG_SYS_SDRAM0_MODT1 0x00000000 -#define CONFIG_SYS_SDRAM0_MODT2 0x00000000 -#define CONFIG_SYS_SDRAM0_MODT3 0x00000000 -#define CONFIG_SYS_SDRAM0_CODT 0x00000020 -#define CONFIG_SYS_SDRAM0_RTR 0x06180000 -#define CONFIG_SYS_SDRAM0_INITPLR0 0xA8380000 -#define CONFIG_SYS_SDRAM0_INITPLR1 0x81900400 -#define CONFIG_SYS_SDRAM0_INITPLR2 0x81020000 -#define CONFIG_SYS_SDRAM0_INITPLR3 0x81030000 -#define CONFIG_SYS_SDRAM0_INITPLR4 0x81010000 -#define CONFIG_SYS_SDRAM0_INITPLR5 0xE4000542 -#define CONFIG_SYS_SDRAM0_INITPLR6 0x81900400 -#define CONFIG_SYS_SDRAM0_INITPLR7 0x8A880000 -#define CONFIG_SYS_SDRAM0_INITPLR8 0x8A880000 -#define CONFIG_SYS_SDRAM0_INITPLR9 0x8A880000 -#define CONFIG_SYS_SDRAM0_INITPLR10 0x8A880000 -#define CONFIG_SYS_SDRAM0_INITPLR11 0x81000442 -#define CONFIG_SYS_SDRAM0_INITPLR12 0x81010380 -#define CONFIG_SYS_SDRAM0_INITPLR13 0x81010000 -#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000 -#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000 -#define CONFIG_SYS_SDRAM0_RQDC 0x80000038 -#define CONFIG_SYS_SDRAM0_RFDC 0x003F0000 -#define CONFIG_SYS_SDRAM0_RDCC 0x80000000 -#define CONFIG_SYS_SDRAM0_DLCR 0x00000000 -#define CONFIG_SYS_SDRAM0_CLKTR 0x40000000 -#define CONFIG_SYS_SDRAM0_WRDTR 0x84000800 -#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000 -#define CONFIG_SYS_SDRAM0_SDTR2 0x32204232 -#define CONFIG_SYS_SDRAM0_SDTR3 0x090B0D15 -#define CONFIG_SYS_SDRAM0_MMODE 0x00000442 -#define CONFIG_SYS_SDRAM0_MEMODE 0x00000000 - -#define CONFIG_SYS_MBYTES_SDRAM 256 /* 256MB */ - -/* - * I2C - */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ - -#define CONFIG_SYS_I2C_MULTI_EEPROMS -#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* I2C bootstrap EEPROM */ -#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x54 -#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 -#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 - -/* I2C SYSMON */ -#define CONFIG_DTT_LM63 1 /* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 - -/* RTC configuration */ -#define CONFIG_RTC_DS1337 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* - * Ethernet - */ -#define CONFIG_IBM_EMAC4_V4 1 - -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 - -#define CONFIG_PHY_ADDR 2 /* PHY address, See schematics */ -#define CONFIG_PHY1_ADDR 3 - -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CONFIG_PHY_DYNAMIC_ANEG 1 - -/* - * USB-OHCI - */ -#define CONFIG_USB_OHCI_NEW -#define CONFIG_USB_STORAGE -#undef CONFIG_SYS_OHCI_BE_CONTROLLER /* 460EX has little endian descriptors*/ -#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS /* 460EX has little endian register */ -#define CONFIG_SYS_OHCI_USE_NPS /* force NoPowerSwitching mode */ -#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_AHB_BASE | 0xd0000) -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 - -/* - * Default environment variables - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_AMCC_DEF_ENV \ - CONFIG_AMCC_DEF_ENV_POWERPC \ - CONFIG_AMCC_DEF_ENV_NOR_UPD \ - "kernel_addr=fc000000\0" \ - "fdt_addr=fc1e0000\0" \ - "ramdisk_addr=fc200000\0" \ - "pciconfighost=1\0" \ - "pcie_mode=RP:RP\0" \ - "" - -/* - * Commands additional to the ones defined in amcc-common.h - */ -#define CONFIG_CMD_CHIP_CONFIG -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DTT -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_PCI -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_USB - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* - * PCI stuff - */ -/* General PCI */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_PCI_CONFIG_HOST_BRIDGE -#define CONFIG_PCI_DISABLE_PCIE - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ -#undef CONFIG_SYS_PCI_MASTER_INIT - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ - - -/* - * External Bus Controller (EBC) Setup - */ - -/* - * CompactCenter has 64MBytes of NOR FLASH (Spansion 29GL512), but the - * boot EBC mapping only supports a maximum of 16MBytes - * (4.ff00.0000 - 4.ffff.ffff). - * To solve this problem, the FLASH has to get remapped to another - * EBC address which accepts bigger regions: - * - * 0xfc00.0000 -> 4.cc00.0000 - */ - - -/* Memory Bank 0 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x10055e00 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000) - -/* Memory Bank 1 (NVRAM) initialization */ -#define CONFIG_SYS_EBC_PB1AP 0x02815480 -/* BAS=NVRAM,BS=1MB,BU=R/W,BW=8bit*/ -#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NVRAM_BASE | 0x18000) - -/* Memory Bank 2 (UART) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x02815480 -/* BAS=UART,BS=1MB,BU=R/W,BW=16bit*/ -#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_UART_BASE | 0x1A000) - -/* Memory Bank 3 (IO) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x02815480 -/* BAS=IO,BS=1MB,BU=R/W,BW=16bit*/ -#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_IO_BASE | 0x1A000) - -/* - * PPC4xx GPIO Configuration - */ -/* 460EX: Use USB configuration */ -#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ -{ \ -/* GPIO Core 0 */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \ -{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 NFCLE */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 NFALE */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO27 IRQ(0) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO28 IRQ(1) */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO30 PerPar0 DMAReq2 IRQ(7)*/ \ -{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO31 PerPar1 DMAAck2 IRQ(8)*/ \ -}, \ -{ \ -/* GPIO Core 1 */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 PerPar2 EOT2/TC2 IRQ(9)*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 PerPar3 DMAReq3 IRQ(4)*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N DMAAck3 UART3_SIN*/ \ -{GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EOT3/TC3 UART3_SOUT*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \ -{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 PerAddr(6) DMAAck0 IRQ(14)*/ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 PerAddr(7) EOT/TC0 IRQ(15)*/ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 USB_SERVICE_SUSPEND_N */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO51 SPI_CSS_N */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO52 FPGA_PROGRAM_UC_N */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 FPGA_INIT_UC_N */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO54 WD_STROBE */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO55 LED_2_OUT */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO56 LED_1_OUT */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO61 STARTUP_FINISHED_N */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO62 STARTUP_FINISHED */ \ -{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 SERVICE_PORT_ACTIVE */ \ -} \ -} - -#endif /* __CONFIG_H */ diff --git a/include/configs/intip.h b/include/configs/intip.h new file mode 100644 index 000000000..4f7bc7e28 --- /dev/null +++ b/include/configs/intip.h @@ -0,0 +1,437 @@ +/* + * (C) Copyright 2009 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * Based on include/configs/canyonlands.h + * (C) Copyright 2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * intip.h - configuration for CompactCenter aka intip (460EX) and DevCon-Center + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +/* + * This config file is used for CompactCenter(codename intip) and DevCon-Center + */ +#define CONFIG_460EX 1 /* Specific PPC460EX */ +#ifdef CONFIG_DEVCONCENTER +#define CONFIG_HOSTNAME devconcenter +#define CONFIG_IDENT_STRING " devconcenter 0.02" +#else +#define CONFIG_HOSTNAME intip +#define CONFIG_IDENT_STRING " intip 0.02" +#endif +#define CONFIG_440 1 +#define CONFIG_4xx 1 /* ... PPC4xx family */ + +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + +#define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ +#define CONFIG_BOARD_TYPES 1 /* support board types */ +#define CONFIG_FIT +#define CFG_ALT_MEMTEST + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE + +/* EBC stuff */ +#ifdef CONFIG_DEVCONCENTER /* Devcon-Center has 128 MB of flash */ +#define CONFIG_SYS_FLASH_BASE 0xF8000000 /* later mapped here */ +#define CONFIG_SYS_FLASH_SIZE (128 << 20) +#else +#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped here */ +#define CONFIG_SYS_FLASH_SIZE (64 << 20) +#endif + +#define CONFIG_SYS_NVRAM_BASE 0xE0000000 +#define CONFIG_SYS_UART_BASE 0xE0100000 +#define CONFIG_SYS_IO_BASE 0xE0200000 + +#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space */ +#define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4 +#ifdef CONFIG_DEVCONCENTER /* Devcon-Center has 128 MB of flash */ +#define CONFIG_SYS_FLASH_BASE_PHYS_L 0xC8000000 +#else +#define CONFIG_SYS_FLASH_BASE_PHYS_L 0xCC000000 +#endif +#define CONFIG_SYS_FLASH_BASE_PHYS \ + (((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) \ + | (u64)CONFIG_SYS_FLASH_BASE_PHYS_L) + +#define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 64k */ +#define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ +#define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000 + +#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal periph. */ + +#define CONFIG_SYS_AHB_BASE 0xE2000000 /* int. AHB periph. */ + +/* + * Initial RAM & stack pointer (placed in OCM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ +#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* + * Serial Port + */ +#undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */ + +/* + * Environment + */ +/* + * Define here the location of the environment variables (FLASH). + */ +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#define CONFIG_SYS_NOR_CS 0 /* NOR chip connected to CSx */ + +/* + * FLASH related + */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* Use AMD reset cmd */ + +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#ifdef CONFIG_DEVCONCENTER +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* max num of sectors per chip*/ +#else +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sectors per chip*/ +#endif + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase/ms */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write/ms */ + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* buff'd writes (20x faster) */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* 'E' for empty sector on flinfo */ + +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector*/ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) +#endif /* CONFIG_ENV_IS_IN_FLASH */ + +/* + * DDR SDRAM + */ + +#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */ + +#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ +#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */ +#undef CONFIG_PPC4xx_DDR_METHOD_A + +/* DDR1/2 SDRAM Device Control Register Data Values */ +/* Memory Queue */ +#define CONFIG_SYS_SDRAM_R0BAS 0x0000f800 +#define CONFIG_SYS_SDRAM_R1BAS 0x00000000 +#define CONFIG_SYS_SDRAM_R2BAS 0x00000000 +#define CONFIG_SYS_SDRAM_R3BAS 0x00000000 +#define CONFIG_SYS_SDRAM_PLBADDULL 0x00000000 +#define CONFIG_SYS_SDRAM_PLBADDUHB 0x00000008 +#define CONFIG_SYS_SDRAM_CONF1LL 0x80001C80 +#define CONFIG_SYS_SDRAM_CONF1HB 0x80001C80 +#define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000 + +/* SDRAM Controller */ +#define CONFIG_SYS_SDRAM0_MB0CF 0x00000201 +#define CONFIG_SYS_SDRAM0_MB1CF 0x00000000 +#define CONFIG_SYS_SDRAM0_MB2CF 0x00000000 +#define CONFIG_SYS_SDRAM0_MB3CF 0x00000000 +#define CONFIG_SYS_SDRAM0_MCOPT1 0x05122000 +#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT0 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT1 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT2 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT3 0x00000000 +#define CONFIG_SYS_SDRAM0_CODT 0x00000020 +#define CONFIG_SYS_SDRAM0_RTR 0x06180000 +#define CONFIG_SYS_SDRAM0_INITPLR0 0xA8380000 +#define CONFIG_SYS_SDRAM0_INITPLR1 0x81900400 +#define CONFIG_SYS_SDRAM0_INITPLR2 0x81020000 +#define CONFIG_SYS_SDRAM0_INITPLR3 0x81030000 +#define CONFIG_SYS_SDRAM0_INITPLR4 0x81010000 +#define CONFIG_SYS_SDRAM0_INITPLR5 0xE4000542 +#define CONFIG_SYS_SDRAM0_INITPLR6 0x81900400 +#define CONFIG_SYS_SDRAM0_INITPLR7 0x8A880000 +#define CONFIG_SYS_SDRAM0_INITPLR8 0x8A880000 +#define CONFIG_SYS_SDRAM0_INITPLR9 0x8A880000 +#define CONFIG_SYS_SDRAM0_INITPLR10 0x8A880000 +#define CONFIG_SYS_SDRAM0_INITPLR11 0x81000442 +#define CONFIG_SYS_SDRAM0_INITPLR12 0x81010380 +#define CONFIG_SYS_SDRAM0_INITPLR13 0x81010000 +#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000 +#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000 +#define CONFIG_SYS_SDRAM0_RQDC 0x80000038 +#define CONFIG_SYS_SDRAM0_RFDC 0x003F0000 +#define CONFIG_SYS_SDRAM0_RDCC 0x80000000 +#define CONFIG_SYS_SDRAM0_DLCR 0x00000000 +#define CONFIG_SYS_SDRAM0_CLKTR 0x40000000 +#define CONFIG_SYS_SDRAM0_WRDTR 0x84000800 +#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000 +#define CONFIG_SYS_SDRAM0_SDTR2 0x32204232 +#define CONFIG_SYS_SDRAM0_SDTR3 0x090B0D15 +#define CONFIG_SYS_SDRAM0_MMODE 0x00000442 +#define CONFIG_SYS_SDRAM0_MEMODE 0x00000000 + +#define CONFIG_SYS_MBYTES_SDRAM 256 /* 256MB */ + +/* + * I2C + */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ + +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* I2C bootstrap EEPROM */ +#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x54 +#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 +#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 + +/* I2C SYSMON */ +#define CONFIG_DTT_LM63 1 /* National LM63 */ +#define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */ +#define CONFIG_DTT_PWM_LOOKUPTABLE \ + { { 40, 10 }, { 50, 20 }, { 60, 40 } } +#define CONFIG_DTT_TACH_LIMIT 0xa10 + +/* RTC configuration */ +#define CONFIG_RTC_DS1337 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +/* + * Ethernet + */ +#define CONFIG_IBM_EMAC4_V4 1 + +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 + +#define CONFIG_PHY_ADDR 2 /* PHY address, See schematics */ +#define CONFIG_PHY1_ADDR 3 + +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CONFIG_PHY_DYNAMIC_ANEG 1 + +/* + * USB-OHCI + */ +#define CONFIG_USB_OHCI_NEW +#define CONFIG_USB_STORAGE +#undef CONFIG_SYS_OHCI_BE_CONTROLLER /* 460EX has little endian descriptors*/ +#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS /* 460EX has little endian register */ +#define CONFIG_SYS_OHCI_USE_NPS /* force NoPowerSwitching mode */ +#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_AHB_BASE | 0xd0000) +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 + +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + "kernel_addr=fc000000\0" \ + "fdt_addr=fc1e0000\0" \ + "ramdisk_addr=fc200000\0" \ + "pciconfighost=1\0" \ + "pcie_mode=RP:RP\0" \ + "" + +/* + * Commands additional to the ones defined in amcc-common.h + */ +#define CONFIG_CMD_CHIP_CONFIG +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +/* + * PCI stuff + */ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_PCI_CONFIG_HOST_BRIDGE +#define CONFIG_PCI_DISABLE_PCIE + +/* Board-specific PCI */ +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ +#undef CONFIG_SYS_PCI_MASTER_INIT + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ + + +/* + * External Bus Controller (EBC) Setup + */ + +/* + * CompactCenter has 64MBytes of NOR FLASH (Spansion 29GL512), but the + * boot EBC mapping only supports a maximum of 16MBytes + * (4.ff00.0000 - 4.ffff.ffff). + * To solve this problem, the FLASH has to get remapped to another + * EBC address which accepts bigger regions: + * + * 0xfc00.0000 -> 4.cc00.0000 + */ + + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x10055e00 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000) + +/* Memory Bank 1 (NVRAM) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x02815480 +/* BAS=NVRAM,BS=1MB,BU=R/W,BW=8bit*/ +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NVRAM_BASE | 0x18000) + +/* Memory Bank 2 (UART) initialization */ +#define CONFIG_SYS_EBC_PB2AP 0x02815480 +/* BAS=UART,BS=1MB,BU=R/W,BW=16bit*/ +#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_UART_BASE | 0x1A000) + +/* Memory Bank 3 (IO) initialization */ +#define CONFIG_SYS_EBC_PB3AP 0x02815480 +/* BAS=IO,BS=1MB,BU=R/W,BW=16bit*/ +#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_IO_BASE | 0x1A000) + +/* + * PPC4xx GPIO Configuration + */ +/* 460EX: Use USB configuration */ +#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +{ \ +/* GPIO Core 0 */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 NFCLE */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 NFALE */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO27 IRQ(0) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO28 IRQ(1) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO30 PerPar0 DMAReq2 IRQ(7)*/ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO31 PerPar1 DMAAck2 IRQ(8)*/ \ +}, \ +{ \ +/* GPIO Core 1 */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 PerPar2 EOT2/TC2 IRQ(9)*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 PerPar3 DMAReq3 IRQ(4)*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N DMAAck3 UART3_SIN*/ \ +{GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EOT3/TC3 UART3_SOUT*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 PerAddr(6) DMAAck0 IRQ(14)*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 PerAddr(7) EOT/TC0 IRQ(15)*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 USB_SERVICE_SUSPEND_N */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO51 SPI_CSS_N */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO52 FPGA_PROGRAM_UC_N */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 FPGA_INIT_UC_N */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO54 WD_STROBE */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO55 LED_2_OUT */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO56 LED_1_OUT */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO61 STARTUP_FINISHED_N */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO62 STARTUP_FINISHED */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 SERVICE_PORT_ACTIVE */ \ +} \ +} + +#endif /* __CONFIG_H */ -- cgit v1.2.3