From f50b619d9cb297b0125fe78dcd6f255eb0d91659 Mon Sep 17 00:00:00 2001 From: Graeme Russ Date: Sun, 23 Aug 2009 12:59:57 +1000 Subject: i386: Moved PCI from #ifdef to conditional compile for sc520 boards Signed-off-by: Graeme Russ --- board/eNET/Makefile | 10 +- board/sc520_cdp/Makefile | 14 +- board/sc520_cdp/sc520_cdp.c | 239 -------------------------- board/sc520_cdp/sc520_cdp_pci.c | 271 ++++++++++++++++++++++++++++++ board/sc520_spunk/Makefile | 14 +- board/sc520_spunk/sc520_spunk.c | 298 --------------------------------- board/sc520_spunk/sc520_spunk_pci.c | 323 ++++++++++++++++++++++++++++++++++++ lib_i386/Makefile | 4 +- lib_i386/pci.c | 3 - lib_i386/pci_type1.c | 5 - 10 files changed, 617 insertions(+), 564 deletions(-) create mode 100644 board/sc520_cdp/sc520_cdp_pci.c create mode 100644 board/sc520_spunk/sc520_spunk_pci.c diff --git a/board/eNET/Makefile b/board/eNET/Makefile index 4813b4b53..bf5736a79 100644 --- a/board/eNET/Makefile +++ b/board/eNET/Makefile @@ -31,12 +31,12 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).a -COBJS := eNET.o -SOBJS := eNET_start16.o eNET_start.o +COBJS-y += eNET.o +SOBJS-y += eNET_start16.o +SOBJS-y += eNET_start.o -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y)) $(LIB): $(obj).depend $(OBJS) $(SOBJS) $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) diff --git a/board/sc520_cdp/Makefile b/board/sc520_cdp/Makefile index 0d2800d5e..7944a01a6 100644 --- a/board/sc520_cdp/Makefile +++ b/board/sc520_cdp/Makefile @@ -28,12 +28,14 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).a -COBJS := sc520_cdp.o flash.o -SOBJS := sc520_cdp_asm.o sc520_cdp_asm16.o - -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) +COBJS-y += sc520_cdp.o +COBJS-y += flash.o +COBJS-$(CONFIG_PCI) += sc520_cdp_pci.o +SOBJS-y += sc520_cdp_asm.o +SOBJS-y += sc520_cdp_asm16.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y)) $(LIB): $(obj).depend $(OBJS) $(SOBJS) $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) diff --git a/board/sc520_cdp/sc520_cdp.c b/board/sc520_cdp/sc520_cdp.c index 9312f4f1d..4c44b2414 100644 --- a/board/sc520_cdp/sc520_cdp.c +++ b/board/sc520_cdp/sc520_cdp.c @@ -23,11 +23,8 @@ */ #include -#include #include -#include #include -#include #include #include #include @@ -114,87 +111,6 @@ static void irq_init(void) sc520_mmcr->eccmap = 0x100; /* Map SDRAM ECC failure INT to NMI */ } -#ifdef CONFIG_PCI -/* PCI stuff */ -static void pci_sc520_cdp_fixup_irq(struct pci_controller *hose, pci_dev_t dev) -{ - /* a configurable lists of irqs to steal - * when we need one (a board with more pci interrupt pins - * would use a larger table */ - static int irq_list[] = { - CONFIG_SYS_FIRST_PCI_IRQ, - CONFIG_SYS_SECOND_PCI_IRQ, - CONFIG_SYS_THIRD_PCI_IRQ, - CONFIG_SYS_FORTH_PCI_IRQ - }; - static int next_irq_index=0; - - uchar tmp_pin; - int pin; - - pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &tmp_pin); - pin = tmp_pin; - - pin-=1; /* pci config space use 1-based numbering */ - if (-1 == pin) { - return; /* device use no irq */ - } - - - /* map device number + pin to a pin on the sc520 */ - switch (PCI_DEV(dev)) { - case 20: - pin+=SC520_PCI_INTA; - break; - - case 19: - pin+=SC520_PCI_INTB; - break; - - case 18: - pin+=SC520_PCI_INTC; - break; - - case 17: - pin+=SC520_PCI_INTD; - break; - - default: - return; - } - - pin&=3; /* wrap around */ - - if (sc520_pci_ints[pin] == -1) { - /* re-route one interrupt for us */ - if (next_irq_index > 3) { - return; - } - if (pci_sc520_set_irq(pin, irq_list[next_irq_index])) { - return; - } - next_irq_index++; - } - - - if (-1 != sc520_pci_ints[pin]) { - pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, - sc520_pci_ints[pin]); - } - PRINTF("fixup_irq: device %d pin %c irq %d\n", - PCI_DEV(dev), 'A' + pin, sc520_pci_ints[pin]); -} - -static struct pci_controller sc520_cdp_hose = { - fixup_irq: pci_sc520_cdp_fixup_irq, -}; - -void pci_init_board(void) -{ - pci_sc520_init(&sc520_cdp_hose); -} -#endif - static void silence_uart(int port) { outb(0, port+1); @@ -321,161 +237,6 @@ static void bus_init(void) * PAR15 Port 0x680 LED display */ -/* - * This function should map a chunk of size bytes - * of the system address space to the ISA bus - * - * The function will return the memory address - * as seen by the host (which may very will be the - * same as the bus address) - */ -u32 isa_map_rom(u32 bus_addr, int size) -{ - u32 par; - - PRINTF("isa_map_rom asked to map %d bytes at %x\n", - size, bus_addr); - - par = size; - if (par < 0x80000) { - par = 0x80000; - } - par >>= 12; - par--; - par&=0x7f; - par <<= 18; - par |= (bus_addr>>12); - par |= 0x50000000; - - PRINTF ("setting PAR11 to %x\n", par); - - /* Map rom 0x10000 with PAR1 */ - sc520_mmcr->par[11] = par; - - return bus_addr; -} - -/* - * this function removed any mapping created - * with pci_get_rom_window() - */ -void isa_unmap_rom(u32 addr) -{ - PRINTF("isa_unmap_rom asked to unmap %x", addr); - if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) { - sc520_mmcr->par[11] = 0; - PRINTF(" done\n"); - return; - } - PRINTF(" not ours\n"); -} - -#ifdef CONFIG_PCI -#define PCI_ROM_TEMP_SPACE 0x10000 -/* - * This function should map a chunk of size bytes - * of the system address space to the PCI bus, - * suitable to map PCI ROMS (bus address < 16M) - * the function will return the host memory address - * which should be converted into a bus address - * before used to configure the PCI rom address - * decoder - */ -u32 pci_get_rom_window(struct pci_controller *hose, int size) -{ - u32 par; - - par = size; - if (par < 0x80000) { - par = 0x80000; - } - par >>= 16; - par--; - par&=0x7ff; - par <<= 14; - par |= (PCI_ROM_TEMP_SPACE>>16); - par |= 0x72000000; - - PRINTF ("setting PAR1 to %x\n", par); - - /* Map rom 0x10000 with PAR1 */ - sc520_mmcr->par[1] = par; - - return PCI_ROM_TEMP_SPACE; -} - -/* - * this function removed any mapping created - * with pci_get_rom_window() - */ -void pci_remove_rom_window(struct pci_controller *hose, u32 addr) -{ - PRINTF("pci_remove_rom_window: %x", addr); - if (addr == PCI_ROM_TEMP_SPACE) { - sc520_mmcr->par[1] = 0; - PRINTF(" done\n"); - return; - } - PRINTF(" not ours\n"); - -} - -/* - * This function is called in order to provide acces to the - * legacy video I/O ports on the PCI bus. - * After this function accesses to I/O ports 0x3b0-0x3bb and - * 0x3c0-0x3df shuld result in transactions on the PCI bus. - * - */ -int pci_enable_legacy_video_ports(struct pci_controller *hose) -{ - /* Map video memory to 0xa0000*/ - sc520_mmcr->par[0] = 0x7200400a; - - /* forward all I/O accesses to PCI */ - sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI; - - - /* so we map away all io ports to pci (only way to access pci io - * below 0x400. But then we have to map back the portions that we dont - * use so that the generate cycles on the GPIO bus where the sio and - * ISA slots are connected, this requre the use of several PAR registers - */ - - /* bring 0x100 - 0x1ef back to ISA using PAR5 */ - sc520_mmcr->par[5] = 0x30ef0100; - - /* IDE use 1f0-1f7 */ - - /* bring 0x1f8 - 0x2f7 back to ISA using PAR6 */ - sc520_mmcr->par[6] = 0x30ff01f8; - - /* com2 use 2f8-2ff */ - - /* bring 0x300 - 0x3af back to ISA using PAR7 */ - sc520_mmcr->par[7] = 0x30af0300; - - /* vga use 3b0-3bb */ - - /* bring 0x3bc - 0x3bf back to ISA using PAR8 */ - sc520_mmcr->par[8] = 0x300303bc; - - /* vga use 3c0-3df */ - - /* bring 0x3e0 - 0x3f5 back to ISA using PAR9 */ - sc520_mmcr->par[9] = 0x301503e0; - - /* ide use 3f6 */ - - /* bring 0x3f7 back to ISA using PAR10 */ - sc520_mmcr->par[10] = 0x300003f7; - - /* com1 use 3f8-3ff */ - - return 0; -} -#endif - /* * Miscelaneous platform dependent initialisations */ diff --git a/board/sc520_cdp/sc520_cdp_pci.c b/board/sc520_cdp/sc520_cdp_pci.c new file mode 100644 index 000000000..ccb79888d --- /dev/null +++ b/board/sc520_cdp/sc520_cdp_pci.c @@ -0,0 +1,271 @@ +/* + * + * (C) Copyright 2002 + * Daniel Engström, Omicron Ceti AB . + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#undef SC520_CDP_DEBUG + +#ifdef SC520_CDP_DEBUG +#define PRINTF(fmt,args...) printf (fmt ,##args) +#else +#define PRINTF(fmt,args...) +#endif + +static void pci_sc520_cdp_fixup_irq(struct pci_controller *hose, pci_dev_t dev) +{ + /* a configurable lists of irqs to steal + * when we need one (a board with more pci interrupt pins + * would use a larger table */ + static int irq_list[] = { + CONFIG_SYS_FIRST_PCI_IRQ, + CONFIG_SYS_SECOND_PCI_IRQ, + CONFIG_SYS_THIRD_PCI_IRQ, + CONFIG_SYS_FORTH_PCI_IRQ + }; + static int next_irq_index=0; + + uchar tmp_pin; + int pin; + + pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &tmp_pin); + pin = tmp_pin; + + pin-=1; /* pci config space use 1-based numbering */ + if (-1 == pin) { + return; /* device use no irq */ + } + + + /* map device number + pin to a pin on the sc520 */ + switch (PCI_DEV(dev)) { + case 20: + pin+=SC520_PCI_INTA; + break; + + case 19: + pin+=SC520_PCI_INTB; + break; + + case 18: + pin+=SC520_PCI_INTC; + break; + + case 17: + pin+=SC520_PCI_INTD; + break; + + default: + return; + } + + pin&=3; /* wrap around */ + + if (sc520_pci_ints[pin] == -1) { + /* re-route one interrupt for us */ + if (next_irq_index > 3) { + return; + } + if (pci_sc520_set_irq(pin, irq_list[next_irq_index])) { + return; + } + next_irq_index++; + } + + + if (-1 != sc520_pci_ints[pin]) { + pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, + sc520_pci_ints[pin]); + } + PRINTF("fixup_irq: device %d pin %c irq %d\n", + PCI_DEV(dev), 'A' + pin, sc520_pci_ints[pin]); +} + +static struct pci_controller sc520_cdp_hose = { + fixup_irq: pci_sc520_cdp_fixup_irq, +}; + +void pci_init_board(void) +{ + pci_sc520_init(&sc520_cdp_hose); +} + +/* + * This function should map a chunk of size bytes + * of the system address space to the ISA bus + * + * The function will return the memory address + * as seen by the host (which may very will be the + * same as the bus address) + */ +u32 isa_map_rom(u32 bus_addr, int size) +{ + u32 par; + + PRINTF("isa_map_rom asked to map %d bytes at %x\n", + size, bus_addr); + + par = size; + if (par < 0x80000) { + par = 0x80000; + } + par >>= 12; + par--; + par&=0x7f; + par <<= 18; + par |= (bus_addr>>12); + par |= 0x50000000; + + PRINTF ("setting PAR11 to %x\n", par); + + /* Map rom 0x10000 with PAR1 */ + sc520_mmcr->par[11] = par; + + return bus_addr; +} + +/* + * this function removed any mapping created + * with pci_get_rom_window() + */ +void isa_unmap_rom(u32 addr) +{ + PRINTF("isa_unmap_rom asked to unmap %x", addr); + if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) { + sc520_mmcr->par[11] = 0; + PRINTF(" done\n"); + return; + } + PRINTF(" not ours\n"); +} + +#define PCI_ROM_TEMP_SPACE 0x10000 +/* + * This function should map a chunk of size bytes + * of the system address space to the PCI bus, + * suitable to map PCI ROMS (bus address < 16M) + * the function will return the host memory address + * which should be converted into a bus address + * before used to configure the PCI rom address + * decoder + */ +u32 pci_get_rom_window(struct pci_controller *hose, int size) +{ + u32 par; + + par = size; + if (par < 0x80000) { + par = 0x80000; + } + par >>= 16; + par--; + par&=0x7ff; + par <<= 14; + par |= (PCI_ROM_TEMP_SPACE>>16); + par |= 0x72000000; + + PRINTF ("setting PAR1 to %x\n", par); + + /* Map rom 0x10000 with PAR1 */ + sc520_mmcr->par[1] = par; + + return PCI_ROM_TEMP_SPACE; +} + +/* + * this function removed any mapping created + * with pci_get_rom_window() + */ +void pci_remove_rom_window(struct pci_controller *hose, u32 addr) +{ + PRINTF("pci_remove_rom_window: %x", addr); + if (addr == PCI_ROM_TEMP_SPACE) { + sc520_mmcr->par[1] = 0; + PRINTF(" done\n"); + return; + } + PRINTF(" not ours\n"); + +} + +/* + * This function is called in order to provide acces to the + * legacy video I/O ports on the PCI bus. + * After this function accesses to I/O ports 0x3b0-0x3bb and + * 0x3c0-0x3df shuld result in transactions on the PCI bus. + * + */ +int pci_enable_legacy_video_ports(struct pci_controller *hose) +{ + /* Map video memory to 0xa0000*/ + sc520_mmcr->par[0] = 0x7200400a; + + /* forward all I/O accesses to PCI */ + sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI; + + + /* so we map away all io ports to pci (only way to access pci io + * below 0x400. But then we have to map back the portions that we dont + * use so that the generate cycles on the GPIO bus where the sio and + * ISA slots are connected, this requre the use of several PAR registers + */ + + /* bring 0x100 - 0x1ef back to ISA using PAR5 */ + sc520_mmcr->par[5] = 0x30ef0100; + + /* IDE use 1f0-1f7 */ + + /* bring 0x1f8 - 0x2f7 back to ISA using PAR6 */ + sc520_mmcr->par[6] = 0x30ff01f8; + + /* com2 use 2f8-2ff */ + + /* bring 0x300 - 0x3af back to ISA using PAR7 */ + sc520_mmcr->par[7] = 0x30af0300; + + /* vga use 3b0-3bb */ + + /* bring 0x3bc - 0x3bf back to ISA using PAR8 */ + sc520_mmcr->par[8] = 0x300303bc; + + /* vga use 3c0-3df */ + + /* bring 0x3e0 - 0x3f5 back to ISA using PAR9 */ + sc520_mmcr->par[9] = 0x301503e0; + + /* ide use 3f6 */ + + /* bring 0x3f7 back to ISA using PAR10 */ + sc520_mmcr->par[10] = 0x300003f7; + + /* com1 use 3f8-3ff */ + + return 0; +} diff --git a/board/sc520_spunk/Makefile b/board/sc520_spunk/Makefile index e04172e3b..06fa2f3f4 100644 --- a/board/sc520_spunk/Makefile +++ b/board/sc520_spunk/Makefile @@ -28,12 +28,14 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).a -COBJS := sc520_spunk.o flash.o -SOBJS := sc520_spunk_asm.o sc520_spunk_asm16.o - -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) +COBJS-y += sc520_spunk.o +COBJS-y += flash.o +COBJS-$(CONFIG_PCI) += sc520_spunk_pci.o +SOBJS-y += sc520_spunk_asm.o +SOBJS-y += sc520_spunk_asm16.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y)) $(LIB): $(obj).depend $(OBJS) $(SOBJS) $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) diff --git a/board/sc520_spunk/sc520_spunk.c b/board/sc520_spunk/sc520_spunk.c index dbb5c48d6..09f11bb4f 100644 --- a/board/sc520_spunk/sc520_spunk.c +++ b/board/sc520_spunk/sc520_spunk.c @@ -23,13 +23,10 @@ */ #include -#include #include #include #include -#include #include -#include #include DECLARE_GLOBAL_DATA_PTR; @@ -98,156 +95,6 @@ static void irq_init(void) } - -/* PCI stuff */ -static void pci_sc520_spunk_fixup_irq(struct pci_controller *hose, pci_dev_t dev) -{ - int version = sc520_mmcr->sysinfo; - - /* a configurable lists of irqs to steal - * when we need one (a board with more pci interrupt pins - * would use a larger table */ - static int irq_list[] = { - CONFIG_SYS_FIRST_PCI_IRQ, - CONFIG_SYS_SECOND_PCI_IRQ, - CONFIG_SYS_THIRD_PCI_IRQ, - CONFIG_SYS_FORTH_PCI_IRQ - }; - static int next_irq_index=0; - - uchar tmp_pin; - int pin; - - pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &tmp_pin); - pin = tmp_pin; - - pin-=1; /* pci config space use 1-based numbering */ - if (-1 == pin) { - return; /* device use no irq */ - } - - - /* map device number + pin to a pin on the sc520 */ - switch (PCI_DEV(dev)) { - case 6: /* ETH0 */ - pin+=SC520_PCI_INTA; - break; - - case 7: /* ETH1 */ - pin+=SC520_PCI_INTB; - break; - - case 8: /* Crypto */ - pin+=SC520_PCI_INTC; - break; - - case 9: /* PMC slot */ - pin+=SC520_PCI_INTD; - break; - - case 10: /* PC-Card */ - - if (version < 10) { - pin+=SC520_PCI_INTD; - } else { - pin+=SC520_PCI_INTC; - } - break; - - default: - return; - } - - pin&=3; /* wrap around */ - - if (sc520_pci_ints[pin] == -1) { - /* re-route one interrupt for us */ - if (next_irq_index > 3) { - return; - } - if (pci_sc520_set_irq(pin, irq_list[next_irq_index])) { - return; - } - next_irq_index++; - } - - - if (-1 != sc520_pci_ints[pin]) { - pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, - sc520_pci_ints[pin]); - } -#if 0 - printf("fixup_irq: device %d pin %c irq %d\n", - PCI_DEV(dev), 'A' + pin, sc520_pci_ints[pin]); -#endif -} - - -static void pci_sc520_spunk_configure_cardbus(struct pci_controller *hose, - pci_dev_t dev, struct pci_config_table *te) -{ - u32 io_base; - u32 temp; - - pciauto_config_device(hose, dev); - - pci_hose_write_config_word(hose, dev, PCI_COMMAND, 0x07); /* enable device */ - pci_hose_write_config_byte(hose, dev, 0x0c, 0x10); /* cacheline size */ - pci_hose_write_config_byte(hose, dev, 0x0d, 0x40); /* latency timer */ - pci_hose_write_config_byte(hose, dev, 0x1b, 0x40); /* cardbus latency timer */ - pci_hose_write_config_word(hose, dev, PCI_BRIDGE_CONTROL, 0x0040); /* reset cardbus */ - pci_hose_write_config_word(hose, dev, PCI_BRIDGE_CONTROL, 0x0080); /* route interrupts though ExCA */ - pci_hose_write_config_word(hose, dev, 0x44, 0x3e0); /* map legacy I/O port to 0x3e0 */ - - pci_hose_read_config_dword(hose, dev, 0x80, &temp); /* System control */ - pci_hose_write_config_dword(hose, dev, 0x80, temp | 0x60); /* System control: disable clockrun */ - /* route MF0 to ~INT and MF3 to IRQ7 - * reserve all others */ - pci_hose_write_config_dword(hose, dev, 0x8c, 0x00007002); - pci_hose_write_config_byte(hose, dev, 0x91, 0x00); /* card control */ - pci_hose_write_config_byte(hose, dev, 0x92, 0x62); /* device control */ - - if (te->device != 0xac56) { - pci_hose_write_config_byte(hose, dev, 0x93, 0x21); /* async interrupt enable */ - pci_hose_write_config_word(hose, dev, 0xa8, 0x0000); /* reset GPIO */ - pci_hose_write_config_word(hose, dev, 0xac, 0x0000); /* reset GPIO */ - pci_hose_write_config_word(hose, dev, 0xaa, 0x0000); /* reset GPIO */ - pci_hose_write_config_word(hose, dev, 0xae, 0x0000); /* reset GPIO */ - } else { - pci_hose_write_config_byte(hose, dev, 0x93, 0x20); /* */ - } - pci_hose_write_config_word(hose, dev, 0xa4, 0x8000); /* reset power management */ - - - pci_hose_read_config_dword(hose, dev, PCI_BASE_ADDRESS_0, &io_base); - io_base &= ~0xfL; - - writeb(0x07, io_base+0x803); /* route CSC irq though ExCA and enable IRQ7 */ - writel(0, io_base+0x10); /* CLKRUN default */ - writel(0, io_base+0x20); /* CLKRUN default */ - -} - - -static struct pci_config_table pci_sc520_spunk_config_table[] = { - { 0x104c, 0xac50, PCI_ANY_ID, 0, 0x0a, 0, pci_sc520_spunk_configure_cardbus, { 0, 0, 0} }, - { 0x104c, 0xac56, PCI_ANY_ID, 0, 0x0a, 0, pci_sc520_spunk_configure_cardbus, { 0, 0, 0} }, - { 0, 0, 0, 0, 0, 0, NULL, {0,0,0}} -}; - -static struct pci_controller sc520_spunk_hose = { - fixup_irq: pci_sc520_spunk_fixup_irq, - config_table: pci_sc520_spunk_config_table, - first_busno: 0x00, - last_busno: 0xff, -}; - -void pci_init_board(void) -{ - pci_sc520_init(&sc520_spunk_hose); -} - - /* set up the ISA bus timing and system address mappings */ static void bus_init(void) { @@ -333,151 +180,6 @@ static void bus_init(void) * PAR15 */ -/* - * This function should map a chunk of size bytes - * of the system address space to the ISA bus - * - * The function will return the memory address - * as seen by the host (which may very will be the - * same as the bus address) - */ -u32 isa_map_rom(u32 bus_addr, int size) -{ - u32 par; - - printf("isa_map_rom asked to map %d bytes at %x\n", - size, bus_addr); - - par = size; - if (par < 0x80000) { - par = 0x80000; - } - par >>= 12; - par--; - par&=0x7f; - par <<= 18; - par |= (bus_addr>>12); - par |= 0x50000000; - - printf ("setting PAR11 to %x\n", par); - - /* Map rom 0x10000 with PAR1 */ - sc520_mmcr->par[11] = par; - - return bus_addr; -} - -/* - * this function removed any mapping created - * with pci_get_rom_window() - */ -void isa_unmap_rom(u32 addr) -{ - printf("isa_unmap_rom asked to unmap %x", addr); - if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) { - sc520_mmcr->par[11] = 0; - printf(" done\n"); - return; - } - printf(" not ours\n"); -} - -#ifdef CONFIG_PCI -#define PCI_ROM_TEMP_SPACE 0x10000 -/* - * This function should map a chunk of size bytes - * of the system address space to the PCI bus, - * suitable to map PCI ROMS (bus address < 16M) - * the function will return the host memory address - * which should be converted into a bus address - * before used to configure the PCI rom address - * decoder - */ -u32 pci_get_rom_window(struct pci_controller *hose, int size) -{ - u32 par; - - par = size; - if (par < 0x80000) { - par = 0x80000; - } - par >>= 16; - par--; - par&=0x7ff; - par <<= 14; - par |= (PCI_ROM_TEMP_SPACE>>16); - par |= 0x72000000; - - printf ("setting PAR1 to %x\n", par); - - /* Map rom 0x10000 with PAR1 */ - sc520_mmcr->par[1] = par; - - return PCI_ROM_TEMP_SPACE; -} - -/* - * this function removed any mapping created - * with pci_get_rom_window() - */ -void pci_remove_rom_window(struct pci_controller *hose, u32 addr) -{ - printf("pci_remove_rom_window: %x", addr); - if (addr == PCI_ROM_TEMP_SPACE) { - sc520_mmcr->par[1] = 0; - printf(" done\n"); - return; - } - printf(" not ours\n"); - -} - -/* - * This function is called in order to provide acces to the - * legacy video I/O ports on the PCI bus. - * After this function accesses to I/O ports 0x3b0-0x3bb and - * 0x3c0-0x3df shuld result in transactions on the PCI bus. - * - */ -int pci_enable_legacy_video_ports(struct pci_controller *hose) -{ - /* Map video memory to 0xa0000*/ - sc520_mmcr->par[0] = 0x7200400a; - - /* forward all I/O accesses to PCI */ - sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI; - - - /* so we map away all io ports to pci (only way to access pci io - * below 0x400. But then we have to map back the portions that we dont - * use so that the generate cycles on the GPIO bus where the sio and - * ISA slots are connected, this requre the use of several PAR registers - */ - - /* bring 0x100 - 0x2f7 back to ISA using PAR5 */ - sc520_mmcr->par[5] = 0x31f70100; - - /* com2 use 2f8-2ff */ - - /* bring 0x300 - 0x3af back to ISA using PAR7 */ - sc520_mmcr->par[7] = 0x30af0300; - - /* vga use 3b0-3bb */ - - /* bring 0x3bc - 0x3bf back to ISA using PAR8 */ - sc520_mmcr->par[8] = 0x300303bc; - - /* vga use 3c0-3df */ - - /* bring 0x3e0 - 0x3f7 back to ISA using PAR9 */ - sc520_mmcr->par[9] = 0x301703e0; - - /* com1 use 3f8-3ff */ - - return 0; -} -#endif - /* * Miscelaneous platform dependent initialisations */ diff --git a/board/sc520_spunk/sc520_spunk_pci.c b/board/sc520_spunk/sc520_spunk_pci.c new file mode 100644 index 000000000..1b5d0f17f --- /dev/null +++ b/board/sc520_spunk/sc520_spunk_pci.c @@ -0,0 +1,323 @@ +/* + * + * (C) Copyright 2002 + * Daniel Engström, Omicron Ceti AB . + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +static void pci_sc520_spunk_fixup_irq(struct pci_controller *hose, pci_dev_t dev) +{ + int version = sc520_mmcr->sysinfo; + + /* a configurable lists of irqs to steal + * when we need one (a board with more pci interrupt pins + * would use a larger table */ + static int irq_list[] = { + CONFIG_SYS_FIRST_PCI_IRQ, + CONFIG_SYS_SECOND_PCI_IRQ, + CONFIG_SYS_THIRD_PCI_IRQ, + CONFIG_SYS_FORTH_PCI_IRQ + }; + static int next_irq_index=0; + + uchar tmp_pin; + int pin; + + pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &tmp_pin); + pin = tmp_pin; + + pin-=1; /* pci config space use 1-based numbering */ + if (-1 == pin) { + return; /* device use no irq */ + } + + + /* map device number + pin to a pin on the sc520 */ + switch (PCI_DEV(dev)) { + case 6: /* ETH0 */ + pin+=SC520_PCI_INTA; + break; + + case 7: /* ETH1 */ + pin+=SC520_PCI_INTB; + break; + + case 8: /* Crypto */ + pin+=SC520_PCI_INTC; + break; + + case 9: /* PMC slot */ + pin+=SC520_PCI_INTD; + break; + + case 10: /* PC-Card */ + + if (version < 10) { + pin+=SC520_PCI_INTD; + } else { + pin+=SC520_PCI_INTC; + } + break; + + default: + return; + } + + pin&=3; /* wrap around */ + + if (sc520_pci_ints[pin] == -1) { + /* re-route one interrupt for us */ + if (next_irq_index > 3) { + return; + } + if (pci_sc520_set_irq(pin, irq_list[next_irq_index])) { + return; + } + next_irq_index++; + } + + + if (-1 != sc520_pci_ints[pin]) { + pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, + sc520_pci_ints[pin]); + } +#if 0 + printf("fixup_irq: device %d pin %c irq %d\n", + PCI_DEV(dev), 'A' + pin, sc520_pci_ints[pin]); +#endif +} + + +static void pci_sc520_spunk_configure_cardbus(struct pci_controller *hose, + pci_dev_t dev, struct pci_config_table *te) +{ + u32 io_base; + u32 temp; + + pciauto_config_device(hose, dev); + + pci_hose_write_config_word(hose, dev, PCI_COMMAND, 0x07); /* enable device */ + pci_hose_write_config_byte(hose, dev, 0x0c, 0x10); /* cacheline size */ + pci_hose_write_config_byte(hose, dev, 0x0d, 0x40); /* latency timer */ + pci_hose_write_config_byte(hose, dev, 0x1b, 0x40); /* cardbus latency timer */ + pci_hose_write_config_word(hose, dev, PCI_BRIDGE_CONTROL, 0x0040); /* reset cardbus */ + pci_hose_write_config_word(hose, dev, PCI_BRIDGE_CONTROL, 0x0080); /* route interrupts though ExCA */ + pci_hose_write_config_word(hose, dev, 0x44, 0x3e0); /* map legacy I/O port to 0x3e0 */ + + pci_hose_read_config_dword(hose, dev, 0x80, &temp); /* System control */ + pci_hose_write_config_dword(hose, dev, 0x80, temp | 0x60); /* System control: disable clockrun */ + /* route MF0 to ~INT and MF3 to IRQ7 + * reserve all others */ + pci_hose_write_config_dword(hose, dev, 0x8c, 0x00007002); + pci_hose_write_config_byte(hose, dev, 0x91, 0x00); /* card control */ + pci_hose_write_config_byte(hose, dev, 0x92, 0x62); /* device control */ + + if (te->device != 0xac56) { + pci_hose_write_config_byte(hose, dev, 0x93, 0x21); /* async interrupt enable */ + pci_hose_write_config_word(hose, dev, 0xa8, 0x0000); /* reset GPIO */ + pci_hose_write_config_word(hose, dev, 0xac, 0x0000); /* reset GPIO */ + pci_hose_write_config_word(hose, dev, 0xaa, 0x0000); /* reset GPIO */ + pci_hose_write_config_word(hose, dev, 0xae, 0x0000); /* reset GPIO */ + } else { + pci_hose_write_config_byte(hose, dev, 0x93, 0x20); /* */ + } + pci_hose_write_config_word(hose, dev, 0xa4, 0x8000); /* reset power management */ + + + pci_hose_read_config_dword(hose, dev, PCI_BASE_ADDRESS_0, &io_base); + io_base &= ~0xfL; + + writeb(0x07, io_base+0x803); /* route CSC irq though ExCA and enable IRQ7 */ + writel(0, io_base+0x10); /* CLKRUN default */ + writel(0, io_base+0x20); /* CLKRUN default */ + +} + + +static struct pci_config_table pci_sc520_spunk_config_table[] = { + { 0x104c, 0xac50, PCI_ANY_ID, 0, 0x0a, 0, pci_sc520_spunk_configure_cardbus, { 0, 0, 0} }, + { 0x104c, 0xac56, PCI_ANY_ID, 0, 0x0a, 0, pci_sc520_spunk_configure_cardbus, { 0, 0, 0} }, + { 0, 0, 0, 0, 0, 0, NULL, {0,0,0}} +}; + +static struct pci_controller sc520_spunk_hose = { + fixup_irq: pci_sc520_spunk_fixup_irq, + config_table: pci_sc520_spunk_config_table, + first_busno: 0x00, + last_busno: 0xff, +}; + +void pci_init_board(void) +{ + pci_sc520_init(&sc520_spunk_hose); +} + +/* + * This function should map a chunk of size bytes + * of the system address space to the ISA bus + * + * The function will return the memory address + * as seen by the host (which may very will be the + * same as the bus address) + */ +u32 isa_map_rom(u32 bus_addr, int size) +{ + u32 par; + + printf("isa_map_rom asked to map %d bytes at %x\n", + size, bus_addr); + + par = size; + if (par < 0x80000) { + par = 0x80000; + } + par >>= 12; + par--; + par&=0x7f; + par <<= 18; + par |= (bus_addr>>12); + par |= 0x50000000; + + printf ("setting PAR11 to %x\n", par); + + /* Map rom 0x10000 with PAR1 */ + sc520_mmcr->par[11] = par; + + return bus_addr; +} + +/* + * this function removed any mapping created + * with pci_get_rom_window() + */ +void isa_unmap_rom(u32 addr) +{ + printf("isa_unmap_rom asked to unmap %x", addr); + if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) { + sc520_mmcr->par[11] = 0; + printf(" done\n"); + return; + } + printf(" not ours\n"); +} + +#define PCI_ROM_TEMP_SPACE 0x10000 +/* + * This function should map a chunk of size bytes + * of the system address space to the PCI bus, + * suitable to map PCI ROMS (bus address < 16M) + * the function will return the host memory address + * which should be converted into a bus address + * before used to configure the PCI rom address + * decoder + */ +u32 pci_get_rom_window(struct pci_controller *hose, int size) +{ + u32 par; + + par = size; + if (par < 0x80000) { + par = 0x80000; + } + par >>= 16; + par--; + par&=0x7ff; + par <<= 14; + par |= (PCI_ROM_TEMP_SPACE>>16); + par |= 0x72000000; + + printf ("setting PAR1 to %x\n", par); + + /* Map rom 0x10000 with PAR1 */ + sc520_mmcr->par[1] = par; + + return PCI_ROM_TEMP_SPACE; +} + +/* + * this function removed any mapping created + * with pci_get_rom_window() + */ +void pci_remove_rom_window(struct pci_controller *hose, u32 addr) +{ + printf("pci_remove_rom_window: %x", addr); + if (addr == PCI_ROM_TEMP_SPACE) { + sc520_mmcr->par[1] = 0; + printf(" done\n"); + return; + } + printf(" not ours\n"); + +} + +/* + * This function is called in order to provide acces to the + * legacy video I/O ports on the PCI bus. + * After this function accesses to I/O ports 0x3b0-0x3bb and + * 0x3c0-0x3df shuld result in transactions on the PCI bus. + * + */ +int pci_enable_legacy_video_ports(struct pci_controller *hose) +{ + /* Map video memory to 0xa0000*/ + sc520_mmcr->par[0] = 0x7200400a; + + /* forward all I/O accesses to PCI */ + sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI; + + + /* so we map away all io ports to pci (only way to access pci io + * below 0x400. But then we have to map back the portions that we dont + * use so that the generate cycles on the GPIO bus where the sio and + * ISA slots are connected, this requre the use of several PAR registers + */ + + /* bring 0x100 - 0x2f7 back to ISA using PAR5 */ + sc520_mmcr->par[5] = 0x31f70100; + + /* com2 use 2f8-2ff */ + + /* bring 0x300 - 0x3af back to ISA using PAR7 */ + sc520_mmcr->par[7] = 0x30af0300; + + /* vga use 3b0-3bb */ + + /* bring 0x3bc - 0x3bf back to ISA using PAR8 */ + sc520_mmcr->par[8] = 0x300303bc; + + /* vga use 3c0-3df */ + + /* bring 0x3e0 - 0x3f7 back to ISA using PAR9 */ + sc520_mmcr->par[9] = 0x301703e0; + + /* com1 use 3f8-3ff */ + + return 0; +} diff --git a/lib_i386/Makefile b/lib_i386/Makefile index ec6f23605..bb9b330ac 100644 --- a/lib_i386/Makefile +++ b/lib_i386/Makefile @@ -32,8 +32,8 @@ SOBJS-y += realmode_switch.o COBJS-y += bios_setup.o COBJS-y += board.o COBJS-y += bootm.o -COBJS-y += pci.o -COBJS-y += pci_type1.o +COBJS-$(CONFIG_PCI) += pci.o +COBJS-$(CONFIG_PCI) += pci_type1.o COBJS-y += realmode.o COBJS-y += video_bios.o COBJS-y += video.o diff --git a/lib_i386/pci.c b/lib_i386/pci.c index f366bdc67..9020e7ce7 100644 --- a/lib_i386/pci.c +++ b/lib_i386/pci.c @@ -26,7 +26,6 @@ #include #include -#ifdef CONFIG_PCI #undef PCI_ROM_SCAN_VERBOSE int pci_shadow_rom(pci_dev_t dev, unsigned char *dest) @@ -151,5 +150,3 @@ int pci_shadow_rom(pci_dev_t dev, unsigned char *dest) return res; } - -#endif diff --git a/lib_i386/pci_type1.c b/lib_i386/pci_type1.c index 8da8c1ced..225ae4a99 100644 --- a/lib_i386/pci_type1.c +++ b/lib_i386/pci_type1.c @@ -11,9 +11,6 @@ */ #include - -#ifdef CONFIG_PCI - #include #include @@ -52,5 +49,3 @@ void pci_setup_type1(struct pci_controller* hose, u32 cfg_addr, u32 cfg_data) hose->cfg_addr = (unsigned int *) cfg_addr; hose->cfg_data = (unsigned char *) cfg_data; } - -#endif -- cgit v1.2.3