From 7a8979591171676417ab36852d8811a8c46accd8 Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Wed, 29 Oct 2008 12:39:26 -0500 Subject: pci/fsl_pci_init: Enable inbound PCI config cycles Add fsl_pci_config_unlock() function to enable a PCI/PCIe interface configured in agent/endpoint mode to respond to inbound PCI configuration cycles. Signed-off-by: Peter Tyser --- drivers/pci/fsl_pci_init.c | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c index 1db42fd8d..db68f2600 100644 --- a/drivers/pci/fsl_pci_init.c +++ b/drivers/pci/fsl_pci_init.c @@ -37,6 +37,11 @@ DECLARE_GLOBAL_DATA_PTR; #include #include +/* Freescale-specific PCI config registers */ +#define FSL_PCI_PBFR 0x44 +#define FSL_PCIE_CAP_ID 0x4c +#define FSL_PCIE_CFG_RDY 0x4b0 + void pciauto_prescan_setup_bridge(struct pci_controller *hose, pci_dev_t dev, int sub_bus); void pciauto_postscan_setup_bridge(struct pci_controller *hose, @@ -306,6 +311,30 @@ void fsl_pci_init(struct pci_controller *hose) } } +/* Enable inbound PCI config cycles for agent/endpoint interface */ +void fsl_pci_config_unlock(struct pci_controller *hose) +{ + pci_dev_t dev = PCI_BDF(hose->first_busno,0,0); + u8 agent; + u8 pcie_cap; + u16 pbfr; + + pci_hose_read_config_byte(hose, dev, PCI_CLASS_PROG, &agent); + if (!agent) + return; + + pci_hose_read_config_byte(hose, dev, FSL_PCIE_CAP_ID, &pcie_cap); + if (pcie_cap != 0x0) { + /* PCIe - set CFG_READY bit of Configuration Ready Register */ + pci_hose_write_config_byte(hose, dev, FSL_PCIE_CFG_RDY, 0x1); + } else { + /* PCI - clear ACL bit of PBFR */ + pci_hose_read_config_word(hose, dev, FSL_PCI_PBFR, &pbfr); + pbfr &= ~0x20; + pci_hose_write_config_word(hose, dev, FSL_PCI_PBFR, pbfr); + } +} + #ifdef CONFIG_OF_BOARD_SETUP #include #include -- cgit v1.2.3 From e92739d34e2d6b6aca93b2598248210710897ce8 Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Wed, 17 Dec 2008 16:36:21 -0600 Subject: Add support for PCA953x I2C gpio devices Initial support for NXP's 4 and 8 bit I2C gpio expanders (eg pca9537, pca9557, etc). The CONFIG_PCA953X define enables support for the devices while the CONFIG_CMD_PCA953X define enables the pca953x command. The CONFIG_CMD_PCA953X_INFO define enables an 'info' sub-command which provides summary information for the given pca953x device. Signed-off-by: Peter Tyser --- Makefile | 2 + README | 9 ++ drivers/gpio/Makefile | 47 ++++++++++ drivers/gpio/pca953x.c | 227 +++++++++++++++++++++++++++++++++++++++++++++++++ include/pca953x.h | 39 +++++++++ 5 files changed, 324 insertions(+) create mode 100644 drivers/gpio/Makefile create mode 100644 drivers/gpio/pca953x.c create mode 100644 include/pca953x.h diff --git a/Makefile b/Makefile index 4df48129b..0fc64902f 100644 --- a/Makefile +++ b/Makefile @@ -228,6 +228,7 @@ LIBS += drivers/bios_emulator/libatibiosemu.a LIBS += drivers/block/libblock.a LIBS += drivers/dma/libdma.a LIBS += drivers/fpga/libfpga.a +LIBS += drivers/gpio/libgpio.a LIBS += drivers/hwmon/libhwmon.a LIBS += drivers/i2c/libi2c.a LIBS += drivers/input/libinput.a @@ -407,6 +408,7 @@ TAG_SUBDIRS += disk TAG_SUBDIRS += common TAG_SUBDIRS += drivers/bios_emulator TAG_SUBDIRS += drivers/block +TAG_SUBDIRS += drivers/gpio TAG_SUBDIRS += drivers/hwmon TAG_SUBDIRS += drivers/i2c TAG_SUBDIRS += drivers/input diff --git a/README b/README index 2a553c274..eb86ebaf1 100644 --- a/README +++ b/README @@ -621,6 +621,8 @@ The following options need to be configured: CONFIG_CMD_MII * MII utility commands CONFIG_CMD_NAND * NAND support CONFIG_CMD_NET bootp, tftpboot, rarpboot + CONFIG_CMD_PCA953X * PCA953x I2C gpio commands + CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command CONFIG_CMD_PCI * pciinfo CONFIG_CMD_PCMCIA * PCMCIA support CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network @@ -698,6 +700,13 @@ The following options need to be configured: Note that if the RTC uses I2C, then the I2C interface must also be configured. See I2C Support, below. +- GPIO Support: + CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO + CONFIG_PCA953X_INFO - enable pca953x info command + + Note that if the GPIO device uses I2C, then the I2C interface + must also be configured. See I2C Support, below. + - Timestamp Support: When CONFIG_TIMESTAMP is selected, the timestamp diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile new file mode 100644 index 000000000..dd618ed71 --- /dev/null +++ b/drivers/gpio/Makefile @@ -0,0 +1,47 @@ +# +# Copyright 2000-2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB := $(obj)libgpio.a + +COBJS-$(CONFIG_PCA953X) += pca953x.o + +COBJS := $(COBJS-y) +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +all: $(LIB) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################## diff --git a/drivers/gpio/pca953x.c b/drivers/gpio/pca953x.c new file mode 100644 index 000000000..390d99ad3 --- /dev/null +++ b/drivers/gpio/pca953x.c @@ -0,0 +1,227 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Driver for NXP's 4 and 8 bit I2C gpio expanders (eg pca9537, pca9557, etc) + * TODO: support additional devices with more than 8-bits GPIO + */ + +#include +#include +#include + +/* Default to an address that hopefully won't corrupt other i2c devices */ +#ifndef CONFIG_SYS_I2C_PCA953X_ADDR +#define CONFIG_SYS_I2C_PCA953X_ADDR (~0) +#endif + +enum { + PCA953X_CMD_INFO, + PCA953X_CMD_DEVICE, + PCA953X_CMD_OUTPUT, + PCA953X_CMD_INPUT, + PCA953X_CMD_INVERT, +}; + +/* + * Modify masked bits in register + */ +static int pca953x_reg_write(uint8_t chip, uint addr, uint mask, uint data) +{ + uint8_t val; + + if (i2c_read(chip, addr, 1, &val, 1)) + return -1; + + val &= ~mask; + val |= data; + + return i2c_write(chip, addr, 1, &val, 1); +} + +/* + * Set output value of IO pins in 'mask' to corresponding value in 'data' + * 0 = low, 1 = high + */ +int pca953x_set_val(uint8_t chip, uint mask, uint data) +{ + return pca953x_reg_write(chip, PCA953X_OUT, mask, data); +} + +/* + * Set read polarity of IO pins in 'mask' to corresponding value in 'data' + * 0 = read pin value, 1 = read inverted pin value + */ +int pca953x_set_pol(uint8_t chip, uint mask, uint data) +{ + return pca953x_reg_write(chip, PCA953X_POL, mask, data); +} + +/* + * Set direction of IO pins in 'mask' to corresponding value in 'data' + * 0 = output, 1 = input + */ +int pca953x_set_dir(uint8_t chip, uint mask, uint data) +{ + return pca953x_reg_write(chip, PCA953X_CONF, mask, data); +} + +/* + * Read current logic level of all IO pins + */ +int pca953x_get_val(uint8_t chip) +{ + uint8_t val; + + if (i2c_read(chip, 0, 1, &val, 1)) + return -1; + + return (int)val; +} + +#ifdef CONFIG_CMD_PCA953X +#ifdef CONFIG_CMD_PCA953X_INFO +/* + * Display pca953x information + */ +static int pca953x_info(uint8_t chip) +{ + int i; + uint8_t data; + + printf("pca953x@ 0x%x:\n\n", chip); + printf("gpio pins: 76543210\n"); + printf("-------------------\n"); + + if (i2c_read(chip, PCA953X_CONF, 1, &data, 1)) + return -1; + printf("conf: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? 'i' : 'o'); + printf("\n"); + + if (i2c_read(chip, PCA953X_POL, 1, &data, 1)) + return -1; + printf("invert: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? '1' : '0'); + printf("\n"); + + if (i2c_read(chip, PCA953X_IN, 1, &data, 1)) + return -1; + printf("input: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? '1' : '0'); + printf("\n"); + + if (i2c_read(chip, PCA953X_OUT, 1, &data, 1)) + return -1; + printf("output: "); + for (i = 7; i >= 0; i--) + printf("%c", data & (1 << i) ? '1' : '0'); + printf("\n"); + + return 0; +} +#endif /* CONFIG_CMD_PCA953X_INFO */ + +cmd_tbl_t cmd_pca953x[] = { + U_BOOT_CMD_MKENT(device, 3, 0, (void *)PCA953X_CMD_DEVICE, "", ""), + U_BOOT_CMD_MKENT(output, 4, 0, (void *)PCA953X_CMD_OUTPUT, "", ""), + U_BOOT_CMD_MKENT(input, 3, 0, (void *)PCA953X_CMD_INPUT, "", ""), + U_BOOT_CMD_MKENT(invert, 4, 0, (void *)PCA953X_CMD_INVERT, "", ""), +#ifdef CONFIG_CMD_PCA953X_INFO + U_BOOT_CMD_MKENT(info, 2, 0, (void *)PCA953X_CMD_INFO, "", ""), +#endif +}; + +int do_pca953x(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + static uint8_t chip = CONFIG_SYS_I2C_PCA953X_ADDR; + int val; + ulong ul_arg2 = 0; + ulong ul_arg3 = 0; + cmd_tbl_t *c; + + c = find_cmd_tbl(argv[1], cmd_pca953x, ARRAY_SIZE(cmd_pca953x)); + + /* All commands but "device" require 'maxargs' arguments */ + if (!c || !((argc == (c->maxargs)) || + (((int)c->cmd == PCA953X_CMD_DEVICE) && + (argc == (c->maxargs - 1))))) { + printf("Usage:\n%s\n", cmdtp->usage); + return 1; + } + + /* arg2 used as chip number or pin number */ + if (argc > 2) + ul_arg2 = simple_strtoul(argv[2], NULL, 16); + + /* arg3 used as pin or invert value */ + if (argc > 3) + ul_arg3 = simple_strtoul(argv[3], NULL, 16) & 0x1; + + switch ((int)c->cmd) { +#ifdef CONFIG_CMD_PCA953X_INFO + case PCA953X_CMD_INFO: + return pca953x_info(chip); +#endif + case PCA953X_CMD_DEVICE: + if (argc == 3) + chip = (uint8_t)ul_arg2; + printf("Current device address: 0x%x\n", chip); + return 0; + case PCA953X_CMD_INPUT: + pca953x_set_dir(chip, (1 << ul_arg2), + PCA953X_DIR_IN << ul_arg2); + val = (pca953x_get_val(chip) & (1 << ul_arg2)) != 0; + + printf("chip 0x%02x, pin 0x%lx = %d\n", chip, ul_arg2, val); + return val; + case PCA953X_CMD_OUTPUT: + pca953x_set_dir(chip, (1 << ul_arg2), + (PCA953X_DIR_OUT << ul_arg2)); + return pca953x_set_val(chip, (1 << ul_arg2), + (ul_arg3 << ul_arg2)); + case PCA953X_CMD_INVERT: + return pca953x_set_pol(chip, (1 << ul_arg2), + (ul_arg3 << ul_arg2)); + default: + /* We should never get here */ + return 1; + } +} + +U_BOOT_CMD( + pca953x, 5, 1, do_pca953x, + "pca953x - pca953x gpio access\n", + "device [dev]\n" + " - show or set current device address\n" +#ifdef CONFIG_CMD_PCA953X_INFO + "pca953x info\n" + " - display info for current chip\n" +#endif + "pca953x output pin 0|1\n" + " - set pin as output and drive low or high\n" + "pca953x invert pin 0|1\n" + " - disable/enable polarity inversion for reads\n" + "pca953x intput pin\n" + " - set pin as input and read value\n" +); + +#endif /* CONFIG_CMD_PCA953X */ diff --git a/include/pca953x.h b/include/pca953x.h new file mode 100644 index 000000000..6c2b58c56 --- /dev/null +++ b/include/pca953x.h @@ -0,0 +1,39 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __PCA953X_H_ +#define __PCA953X_H_ + +#define PCA953X_IN 0x00 +#define PCA953X_OUT 0x01 +#define PCA953X_POL 0x02 +#define PCA953X_CONF 0x03 + +#define PCA953X_OUT_LOW 0 +#define PCA953X_OUT_HIGH 1 +#define PCA953X_POL_NORMAL 0 +#define PCA953X_POL_INVERT 1 +#define PCA953X_DIR_OUT 0 +#define PCA953X_DIR_IN 1 + +int pca953x_set_val(u8 chip, uint mask, uint data); +int pca953x_set_pol(u8 chip, uint mask, uint data); +int pca953x_set_dir(u8 chip, uint mask, uint data); +int pca953x_get_val(u8 chip); + +#endif /* __PCA953X_H_ */ -- cgit v1.2.3 From ccf0fdd02b97323f8caae18d06cc9daeac2f192f Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Wed, 17 Dec 2008 16:36:23 -0600 Subject: XPedite5370 board support Initial support for Extreme Engineering Solutions XPedite5370 - a MPC8572-based 3U VPX single board computer with a PMC/XMC site. Signed-off-by: Peter Tyser --- MAINTAINERS | 3 + MAKEALL | 1 + Makefile | 3 + board/xes/common/Makefile | 56 ++++ board/xes/common/fsl_8572_clk.c | 51 ++++ board/xes/common/fsl_85xx_ddr.c | 93 ++++++ board/xes/common/fsl_85xx_pci.c | 265 ++++++++++++++++ board/xes/xpedite5370/Makefile | 45 +++ board/xes/xpedite5370/config.mk | 35 +++ board/xes/xpedite5370/ddr.c | 270 +++++++++++++++++ board/xes/xpedite5370/law.c | 54 ++++ board/xes/xpedite5370/tlb.c | 94 ++++++ board/xes/xpedite5370/u-boot.lds | 145 +++++++++ board/xes/xpedite5370/xpedite5370.c | 128 ++++++++ include/configs/XPEDITE5370.h | 589 ++++++++++++++++++++++++++++++++++++ 15 files changed, 1832 insertions(+) create mode 100644 board/xes/common/Makefile create mode 100644 board/xes/common/fsl_8572_clk.c create mode 100644 board/xes/common/fsl_85xx_ddr.c create mode 100644 board/xes/common/fsl_85xx_pci.c create mode 100644 board/xes/xpedite5370/Makefile create mode 100644 board/xes/xpedite5370/config.mk create mode 100644 board/xes/xpedite5370/ddr.c create mode 100644 board/xes/xpedite5370/law.c create mode 100644 board/xes/xpedite5370/tlb.c create mode 100644 board/xes/xpedite5370/u-boot.lds create mode 100644 board/xes/xpedite5370/xpedite5370.c create mode 100644 include/configs/XPEDITE5370.h diff --git a/MAINTAINERS b/MAINTAINERS index f04879555..be10eb49a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -411,6 +411,9 @@ Rune Torgersen MPC8266ADS MPC8266 +Peter Tyser + + XPEDITE5370 MPC8572 David Updegraff diff --git a/MAKEALL b/MAKEALL index cc49a9808..a136bad7a 100755 --- a/MAKEALL +++ b/MAKEALL @@ -385,6 +385,7 @@ LIST_85xx=" \ TQM8548 \ TQM8555 \ TQM8560 \ + XPEDITE5370 \ " ######################################################################### diff --git a/Makefile b/Makefile index 0fc64902f..752a37066 100644 --- a/Makefile +++ b/Makefile @@ -2463,6 +2463,9 @@ TQM8560_config: unconfig echo "#define CONFIG_BOARDNAME \"TQM$${CTYPE}\"">>$(obj)include/config.h; @$(MKCONFIG) -a TQM85xx ppc mpc85xx tqm85xx tqc +XPEDITE5370_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc mpc85xx xpedite5370 xes + ######################################################################### ## MPC86xx Systems ######################################################################### diff --git a/board/xes/common/Makefile b/board/xes/common/Makefile new file mode 100644 index 000000000..c5cd6331e --- /dev/null +++ b/board/xes/common/Makefile @@ -0,0 +1,56 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +ifneq ($(OBJTREE),$(SRCTREE)) +$(shell mkdir -p $(obj)board/$(VENDOR)/common) +endif + +LIB = $(obj)lib$(VENDOR).a + +COBJS-$(CONFIG_MPC8572) += fsl_8572_clk.o +COBJS-$(CONFIG_MPC85xx) += fsl_85xx_ddr.o +COBJS-$(CONFIG_FSL_PCI_INIT) += fsl_85xx_pci.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/xes/common/fsl_8572_clk.c b/board/xes/common/fsl_8572_clk.c new file mode 100644 index 000000000..f5df2dae8 --- /dev/null +++ b/board/xes/common/fsl_8572_clk.c @@ -0,0 +1,51 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + +/* + * Return SYSCLK input frequency - 50 MHz or 66 MHz depending on POR config + */ +unsigned long get_board_sys_clk(ulong dummy) +{ + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 gpporcr = gur->gpporcr; + + if (gpporcr & 0x10000) + return 66666666; + else + return 50000000; +} + +/* + * Return DDR input clock - synchronous with SYSCLK or 66 MHz + */ +unsigned long get_board_ddr_clk(ulong dummy) +{ + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 ddr_ratio = ((gur->porpllsr) & 0x00003e00) >> 9; + + if (ddr_ratio == 0x7) + return get_board_sys_clk(dummy); + + return 66666666; +} diff --git a/board/xes/common/fsl_85xx_ddr.c b/board/xes/common/fsl_85xx_ddr.c new file mode 100644 index 000000000..30b476701 --- /dev/null +++ b/board/xes/common/fsl_85xx_ddr.c @@ -0,0 +1,93 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +extern void ddr_enable_ecc(unsigned int dram_size); +#endif + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + + dram_size *= 0x100000; + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* Initialize and enable DDR ECC */ + ddr_enable_ecc(dram_size); +#endif + + return dram_size; +} + +#if defined(CONFIG_DDR_ECC) || (CONFIG_NUM_DDR_CONTROLLERS > 1) +void board_add_ram_info(int use_default) +{ +#if (CONFIG_NUM_DDR_CONTROLLERS > 1) + volatile ccsr_ddr_t *ddr1 = (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR); +#endif + + puts(" ("); + +#if (CONFIG_NUM_DDR_CONTROLLERS > 1) + /* Print interleaving information */ + if (ddr1->cs0_config & 0x20000000) { + switch ((ddr1->cs0_config >> 24) & 0xf) { + case 0: + puts("cache line"); + break; + case 1: + puts("page"); + break; + case 2: + puts("bank"); + break; + case 3: + puts("super-bank"); + break; + default: + puts("invalid"); + break; + } + } else { + puts("no"); + } + + puts(" interleaving"); +#endif + +#if (CONFIG_NUM_DDR_CONTROLLERS > 1) && defined(CONFIG_DDR_ECC) + puts(", "); +#endif + +#if defined(CONFIG_DDR_ECC) + puts("ECC enabled"); +#endif + + puts(")"); +} +#endif /* CONFIG_DDR_ECC || CONFIG_NUM_DDR_CONTROLLERS > 1 */ diff --git a/board/xes/common/fsl_85xx_pci.c b/board/xes/common/fsl_85xx_pci.c new file mode 100644 index 000000000..b8e363ec9 --- /dev/null +++ b/board/xes/common/fsl_85xx_pci.c @@ -0,0 +1,265 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +extern int fsl_pci_setup_inbound_windows(struct pci_region *r); +extern void fsl_pci_init(struct pci_controller *hose); + +int first_free_busno = 0; + +#ifdef CONFIG_PCIE1 +static struct pci_controller pcie1_hose; +#endif +#ifdef CONFIG_PCIE2 +static struct pci_controller pcie2_hose; +#endif +#ifdef CONFIG_PCIE3 +static struct pci_controller pcie3_hose; +#endif + +/* Correlate host/agent POR bits to usable info. Table 4-14 */ +struct host_agent_cfg_t { + uchar pcie_root[3]; + uchar rio_host; +} host_agent_cfg[8] = { + {{0, 0, 0}, 0}, + {{0, 1, 1}, 1}, + {{1, 0, 1}, 0}, + {{1, 1, 0}, 1}, + {{0, 0, 1}, 0}, + {{0, 1, 0}, 1}, + {{1, 0, 0}, 0}, + {{1, 1, 1}, 1} +}; + +/* Correlate port width POR bits to usable info. Table 4-15 */ +struct io_port_cfg_t { + uchar pcie_width[3]; + uchar rio_width; +} io_port_cfg[16] = { + {{0, 0, 0}, 0}, + {{0, 0, 0}, 0}, + {{4, 0, 0}, 0}, + {{4, 4, 0}, 0}, + {{0, 0, 0}, 0}, + {{0, 0, 0}, 0}, + {{0, 0, 0}, 4}, + {{4, 2, 2}, 0}, + {{0, 0, 0}, 0}, + {{0, 0, 0}, 0}, + {{0, 0, 0}, 0}, + {{4, 0, 0}, 4}, + {{4, 0, 0}, 4}, + {{0, 0, 0}, 4}, + {{0, 0, 0}, 4}, + {{8, 0, 0}, 0}, +}; + +void pci_init_board(void) +{ + struct pci_controller *hose; + volatile ccsr_fsl_pci_t *pci; + int width; + int host; + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + uint devdisr = gur->devdisr; + uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19; + uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16; + struct pci_region *r; + + debug(" pci_init_board: devdisr=%x, io_sel=%x, host_agent=%x\n", + devdisr, io_sel, host_agent); + +#ifdef CONFIG_PCIE1 + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; + hose = &pcie1_hose; + host = host_agent_cfg[host_agent].pcie_root[0]; + width = io_port_cfg[io_sel].pcie_width[0]; + r = hose->regions; + + if (width && !(devdisr & MPC85xx_DEVDISR_PCIE)) { + printf("\n PCIE1 connected as %s (x%d)", + host ? "Root Complex" : "End Point", width); + if (pci->pme_msg_det) { + pci->pme_msg_det = 0xffffffff; + debug(" with errors. Clearing. Now 0x%08x", + pci->pme_msg_det); + } + printf("\n"); + + /* inbound */ + r += fsl_pci_setup_inbound_windows(r); + + /* outbound memory */ + pci_set_region(r++, + CONFIG_SYS_PCIE1_MEM_BASE, + CONFIG_SYS_PCIE1_MEM_PHYS, + CONFIG_SYS_PCIE1_MEM_SIZE, + PCI_REGION_MEM); + + /* outbound io */ + pci_set_region(r++, + CONFIG_SYS_PCIE1_IO_BASE, + CONFIG_SYS_PCIE1_IO_PHYS, + CONFIG_SYS_PCIE1_IO_SIZE, + PCI_REGION_IO); + + hose->region_count = r - hose->regions; + + hose->first_busno = first_free_busno; + pci_setup_indirect(hose, (int)&pci->cfg_addr, + (int) &pci->cfg_data); + + fsl_pci_init(hose); + + first_free_busno = hose->last_busno+1; + printf(" PCIE1 on bus %02x - %02x\n", + hose->first_busno, hose->last_busno); + } +#else + gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */ +#endif /* CONFIG_PCIE1 */ + +#ifdef CONFIG_PCIE2 + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR; + hose = &pcie2_hose; + host = host_agent_cfg[host_agent].pcie_root[1]; + width = io_port_cfg[io_sel].pcie_width[1]; + r = hose->regions; + + if (width && !(devdisr & MPC85xx_DEVDISR_PCIE2)) { + printf("\n PCIE2 connected as %s (x%d)", + host ? "Root Complex" : "End Point", width); + if (pci->pme_msg_det) { + pci->pme_msg_det = 0xffffffff; + debug(" with errors. Clearing. Now 0x%08x", + pci->pme_msg_det); + } + printf("\n"); + + /* inbound */ + r += fsl_pci_setup_inbound_windows(r); + + /* outbound memory */ + pci_set_region(r++, + CONFIG_SYS_PCIE2_MEM_BASE, + CONFIG_SYS_PCIE2_MEM_PHYS, + CONFIG_SYS_PCIE2_MEM_SIZE, + PCI_REGION_MEM); + + /* outbound io */ + pci_set_region(r++, + CONFIG_SYS_PCIE2_IO_BASE, + CONFIG_SYS_PCIE2_IO_PHYS, + CONFIG_SYS_PCIE2_IO_SIZE, + PCI_REGION_IO); + + hose->region_count = r - hose->regions; + + hose->first_busno = first_free_busno; + pci_setup_indirect(hose, (int)&pci->cfg_addr, + (int)&pci->cfg_data); + + fsl_pci_init(hose); + first_free_busno = hose->last_busno+1; + printf(" PCIE2 on bus %02x - %02x\n", + hose->first_busno, hose->last_busno); + + } +#else + gur->devdisr |= MPC85xx_DEVDISR_PCIE2; /* disable */ +#endif /* CONFIG_PCIE2 */ + +#ifdef CONFIG_PCIE3 + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE3_ADDR; + hose = &pcie3_hose; + host = host_agent_cfg[host_agent].pcie_root[2]; + width = io_port_cfg[io_sel].pcie_width[2]; + r = hose->regions; + + if (width && !(devdisr & MPC85xx_DEVDISR_PCIE3)) { + printf("\n PCIE3 connected as %s (x%d)", + host ? "Root Complex" : "End Point", width); + if (pci->pme_msg_det) { + pci->pme_msg_det = 0xffffffff; + debug(" with errors. Clearing. Now 0x%08x", + pci->pme_msg_det); + } + printf("\n"); + + /* inbound */ + r += fsl_pci_setup_inbound_windows(r); + + /* outbound memory */ + pci_set_region(r++, + CONFIG_SYS_PCIE3_MEM_BASE, + CONFIG_SYS_PCIE3_MEM_PHYS, + CONFIG_SYS_PCIE3_MEM_SIZE, + PCI_REGION_MEM); + + /* outbound io */ + pci_set_region(r++, + CONFIG_SYS_PCIE3_IO_BASE, + CONFIG_SYS_PCIE3_IO_PHYS, + CONFIG_SYS_PCIE3_IO_SIZE, + PCI_REGION_IO); + + hose->region_count = r - hose->regions; + + hose->first_busno = first_free_busno; + pci_setup_indirect(hose, (int)&pci->cfg_addr, + (int)&pci->cfg_data); + + fsl_pci_init(hose); + first_free_busno = hose->last_busno+1; + printf(" PCIE3 on bus %02x - %02x\n", + hose->first_busno, hose->last_busno); + } +#else + gur->devdisr |= MPC85xx_DEVDISR_PCIE3; /* disable */ +#endif /* CONFIG_PCIE3 */ +} + +#if defined(CONFIG_OF_BOARD_SETUP) +extern void ft_fsl_pci_setup(void *blob, const char *pci_alias, + struct pci_controller *hose); + +void ft_board_pci_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCIE1 + ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); +#endif +#ifdef CONFIG_PCIE2 + ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); +#endif +#ifdef CONFIG_PCIE3 + ft_fsl_pci_setup(blob, "pci0", &pcie3_hose); +#endif +} +#endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/board/xes/xpedite5370/Makefile b/board/xes/xpedite5370/Makefile new file mode 100644 index 000000000..919397c40 --- /dev/null +++ b/board/xes/xpedite5370/Makefile @@ -0,0 +1,45 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2007 Freescale Semiconductor, Inc. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS-y)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/xes/xpedite5370/config.mk b/board/xes/xpedite5370/config.mk new file mode 100644 index 000000000..39469b22c --- /dev/null +++ b/board/xes/xpedite5370/config.mk @@ -0,0 +1,35 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2007-2008 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# xpedite5370 board +# +ifndef TEXT_BASE +TEXT_BASE = 0xfff80000 +endif + +PLATFORM_RELFLAGS += -mrelocatable + +PLATFORM_CPPFLAGS += -DCONFIG_E500=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC8572=1 diff --git a/board/xes/xpedite5370/ddr.c b/board/xes/xpedite5370/ddr.c new file mode 100644 index 000000000..4d3f255d7 --- /dev/null +++ b/board/xes/xpedite5370/ddr.c @@ -0,0 +1,270 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +#include +#include + +static void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address) +{ + i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, + sizeof(ddr2_spd_eeprom_t)); +} + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_ddr_freq(0); +} + +void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd, + unsigned int ctrl_num) +{ + unsigned int i; + unsigned int i2c_address = 0; + + for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) { + if (ctrl_num == 0) + i2c_address = SPD_EEPROM_ADDRESS1; + if (ctrl_num == 1) + i2c_address = SPD_EEPROM_ADDRESS2; + get_spd(&(ctrl_dimms_spd[i]), i2c_address); + } +} + +/* + * There are four board-specific SDRAM timing parameters which must be + * calculated based on the particular PCB artwork. These are: + * 1.) CPO (Read Capture Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. + * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths. + * Unless clock and DQ lanes are very different + * lengths (>2"), this should be set to the nominal value + * of 1/2 clock delay. + * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control) + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations + * 4.) 2T Timing on Addr/Ctl + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) + * + * ====== XPedite5370 DDR2-600 read delay calculations ====== + * + * See Freescale's App Note AN2583 as refrence. This document also + * contains the chip-specific delays for 8548E, 8572, etc. + * + * For MPC8572E + * Minimum chip delay (Ch 0): 1.372ns + * Maximum chip delay (Ch 0): 2.914ns + * Minimum chip delay (Ch 1): 1.220ns + * Maximum chip delay (Ch 1): 2.595ns + * + * CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps + * + * Minimum delay calc (Ch 0): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 2.3" * 180 - 400ps + 1.9" * 180 + 2080ps + 1372ps + * = 3808ps + * = 3.808ns + * + * Maximum delay calc (Ch 0): + * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly + * 2.3" * 180 + 400ps + 2.4" * 180 + 2080ps + 2914ps + * = 6240ps + * = 6.240ns + * + * Minimum delay calc (Ch 1): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180- 400ps + 0.7" * 180 + 2080ps + 1220ps + * = 3288ps + * = 3.288ns + * + * Maximum delay calc (Ch 1): + * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180+ 400ps + 1.1" * 180 + 2080ps + 2595ps + * = 5536ps + * = 5.536ns + * + * Ch.0: 3.808ns to 6.240ns additional delay needed (pick 5ns as target) + * This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) + * Ch.1: 3.288ns to 5.536ns additional delay needed (pick 4.4ns as target) + * This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7) + * + * + * ====== XPedite5370 DDR2-800 read delay calculations ====== + * + * See Freescale's App Note AN2583 as refrence. This document also + * contains the chip-specific delays for 8548E, 8572, etc. + * + * For MPC8572E + * Minimum chip delay (Ch 0): 1.372ns + * Maximum chip delay (Ch 0): 2.914ns + * Minimum chip delay (Ch 1): 1.220ns + * Maximum chip delay (Ch 1): 2.595ns + * + * CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps + * + * Minimum delay calc (Ch 0): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 2.3" * 180 - 350ps + 1.9" * 180 + 1563ps + 1372ps + * = 3341ps + * = 3.341ns + * + * Maximum delay calc (Ch 0): + * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly + * 2.3" * 180 + 350ps + 2.4" * 180 + 1563ps + 2914ps + * = 5673ps + * = 5.673ns + * + * Minimum delay calc (Ch 1): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180- 350ps + 0.7" * 180 + 1563ps + 1220ps + * = 2822ps + * = 2.822ns + * + * Maximum delay calc (Ch 1): + * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180+ 350ps + 1.1" * 180 + 1563ps + 2595ps + * = 4968ps + * = 4.968ns + * + * Ch.0: 3.341ns to 5.673ns additional delay needed (pick 4.5ns as target) + * This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9) + * Ch.1: 2.822ns to 4.968ns additional delay needed (pick 3.9ns as target) + * This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) + * + * Write latency (WR_DATA_DELAY) is calculated by doing the following: + * + * The DDR SDRAM specification requires DQS be received no sooner than + * 75% of an SDRAM clock period—and no later than 125% of a clock + * period—from the capturing clock edge of the command/address at the + * SDRAM. + * + * Based on the above tracelengths, the following are calculated: + * Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 = 0.342ns + * Ch. 0 8572 to DRAM propagation (CLKs) : 2.3" * 180 = 0.414ns + * Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 = 0.126ns + * Ch. 1 8572 to DRAM propagation (CLKs ) : 1.47" * 180 = 0.264ns + * + * Difference in arrival time CLK vs. DQS: + * Ch. 0 0.072ns + * Ch. 1 0.138ns + * + * Both of these values are much less than 25% of the clock + * period at DDR2-600 or DDR2-800, so no additional delay is needed over + * the 1/2 cycle which normally aligns the first DQS transition + * exactly WL (CAS latency minus one cycle) after the CAS strobe. + * See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's + * terminology corresponds to exactly one clock period delay after + * the CAS strobe. (due to the fact that the "delay" is referenced + * from the *falling* edge of the CLK, just after the rising edge + * which the CAS strobe is latched on. + */ + +typedef struct board_memctl_options { + uint16_t datarate_mhz_low; + uint16_t datarate_mhz_high; + uint8_t clk_adjust; + uint8_t cpo_override; + uint8_t write_data_delay; +} board_memctl_options_t; + +static struct board_memctl_options bopts_ctrl[][2] = { + { + /* Controller 0 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 9, + .write_data_delay = 2, + }, + }, + { + /* Controller 1 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 7, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + }, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + struct board_memctl_options *bopts = bopts_ctrl[ctrl_num]; + sys_info_t sysinfo; + int i; + unsigned int datarate; + + get_sys_info(&sysinfo); + datarate = sysinfo.freqDDRBus / 1000 / 1000; + + for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) { + if ((bopts[i].datarate_mhz_low <= datarate) && + (bopts[i].datarate_mhz_high >= datarate)) { + debug("controller %d:\n", ctrl_num); + debug(" clk_adjust = %d\n", bopts[i].clk_adjust); + debug(" cpo = %d\n", bopts[i].cpo_override); + debug(" write_data_delay = %d\n", + bopts[i].write_data_delay); + popts->clk_adjust = bopts[i].clk_adjust; + popts->cpo_override = bopts[i].cpo_override; + popts->write_data_delay = bopts[i].write_data_delay; + } + } + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} diff --git a/board/xes/xpedite5370/law.c b/board/xes/xpedite5370/law.c new file mode 100644 index 000000000..daee676c4 --- /dev/null +++ b/board/xes/xpedite5370/law.c @@ -0,0 +1,54 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +#ifdef CONFIG_SYS_PCIE1_MEM_PHYS + SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_1G, LAW_TRGT_IF_PCIE_1), + SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_1), +#endif +#ifdef CONFIG_SYS_PCIE2_MEM_PHYS + SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_2), + SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_2), +#endif +#ifdef CONFIG_SYS_PCIE3_MEM_PHYS + SET_LAW(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_3), + SET_LAW(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_3), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/xes/xpedite5370/tlb.c b/board/xes/xpedite5370/tlb.c new file mode 100644 index 000000000..caafa3011 --- /dev/null +++ b/board/xes/xpedite5370/tlb.c @@ -0,0 +1,94 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + +#ifdef CONFIG_PCIE1 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), +#endif + +#ifdef CONFIG_PCIE2 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), +#endif + +#ifdef CONFIG_PCIE3 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_64M, 1), +#endif + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/xes/xpedite5370/u-boot.lds b/board/xes/xpedite5370/u-boot.lds new file mode 100644 index 000000000..cb399120d --- /dev/null +++ b/board/xes/xpedite5370/u-boot.lds @@ -0,0 +1,145 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +PHDRS +{ + text PT_LOAD; + bss PT_LOAD; +} + +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + *(.text) + *(.got1) + } :text + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } :text + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + .bootpg ADDR(.text) + 0x7f000 : + { + cpu/mpc85xx/start.o (.bootpg) + } :text = 0xffff + + .resetvec ADDR(.text) + 0x7fffc : + { + *(.resetvec) + } :text = 0xffff + + . = ADDR(.text) + 0x80000; + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } :bss + + . = ALIGN(4); + _end = . ; + PROVIDE (end = .); +} diff --git a/board/xes/xpedite5370/xpedite5370.c b/board/xes/xpedite5370/xpedite5370.c new file mode 100644 index 000000000..487509527 --- /dev/null +++ b/board/xes/xpedite5370/xpedite5370.c @@ -0,0 +1,128 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +int checkboard(void) +{ + char *s; + + printf("Board: X-ES %s 3U VPX SBC\n", CONFIG_SYS_BOARD_NAME); + printf(" "); + s = getenv("board_rev"); + if (s) + printf("Rev %s, ", s); + s = getenv("serial#"); + if (s) + printf("Serial# %s, ", s); + s = getenv("board_cfg"); + if (s) + printf("Cfg %s", s); + printf("\n"); + + return 0; +} + +static void flash_cs_fixup(void) +{ + volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS)); + printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + lbc->br0 = CONFIG_SYS_BR1_PRELIM; + lbc->or0 = CONFIG_SYS_OR1_PRELIM; + + lbc->br1 = CONFIG_SYS_BR0_PRELIM; + lbc->or1 = CONFIG_SYS_OR0_PRELIM; + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif + +#ifdef CONFIG_MP +extern void cpu_mp_lmb_reserve(struct lmb *lmb); + +void board_lmb_reserve(struct lmb *lmb) +{ + cpu_mp_lmb_reserve(lmb); +} +#endif diff --git a/include/configs/XPEDITE5370.h b/include/configs/XPEDITE5370.h new file mode 100644 index 000000000..3bc0fe8f6 --- /dev/null +++ b/include/configs/XPEDITE5370.h @@ -0,0 +1,589 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * xpedite5370 board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8572 1 +#define CONFIG_XPEDITE5370 1 +#define CONFIG_SYS_BOARD_NAME "XPedite5370" +#define CONFIG_NUM_CPUS 2 /* 2 Cores */ +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ +#define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */ + +#define CONFIG_PCI 1 /* Enable PCI/PCIE */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 1 /* PCIE controler 2 */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +/* + * DDR config + */ +#define CONFIG_FSL_DDR2 +#undef CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ +#define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ +#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ +#define CONFIG_NUM_DDR_CONTROLLERS 2 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#ifndef __ASSEMBLY__ +extern unsigned long get_board_sys_clk(unsigned long dummy); +extern unsigned long get_board_ddr_clk(unsigned long dummy); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) +#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) + +/* + * Diagnostics + */ +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x20000000 + +/* + * Memory map + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable + * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable + * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable + * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable + * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable + * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable + * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable + * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable + * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable + */ + +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3) + +/* + * NAND flash configuration + */ +#define CONFIG_SYS_NAND_BASE 0xef800000 +#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ + +/* + * NOR flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xf8000000 +#define CONFIG_SYS_FLASH_BASE2 0xf0000000 +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ + {0xf7f40000, 0xc0000} } +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +/* + * Chip select configuration + */ +/* NOR Flash 0 on CS0 */ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ + OR_GPCM_CSNT | \ + OR_GPCM_XACS | \ + OR_GPCM_ACS_DIV2 | \ + OR_GPCM_SCY_8 | \ + OR_GPCM_TRLX | \ + OR_GPCM_EHTR | \ + OR_GPCM_EAD) + +/* NOR Flash 1 on CS1 */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM + +/* NAND flash on CS2 */ +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ + (2< " + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE + +/* PEX8518 slave I2C interface */ +#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 + +/* I2C DS1631 temperature sensor */ +#define CONFIG_SYS_I2C_DS1621_ADDR 0x48 +#define CONFIG_DTT_DS1621 +#define CONFIG_DTT_SENSORS { 0 } + +/* I2C EEPROM - AT24C128B */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ + +/* I2C RTC */ +#define CONFIG_RTC_M41T11 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 2000 + +/* GPIO/EEPROM/SRAM */ +#define CONFIG_DS4510 +#define CONFIG_SYS_I2C_DS4510_ADDR 0x51 + +/* GPIO */ +#define CONFIG_PCA953X +#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 +#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c +#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e +#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f +#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 + +/* + * PU = pulled high, PD = pulled low + * I = input, O = output, IO = input/output + */ +/* PCA9557 @ 0x18*/ +#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ +#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ +#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ +#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ +#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ +#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ +#define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ +#define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ + +/* PCA9557 @ 0x1c*/ +#define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ +#define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ +#define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ +#define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ +#define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ +#define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ +#define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ +#define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ + +/* PCA9557 @ 0x1e*/ +#define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ +#define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ +#define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ + +/* PCA9557 @ 0x1f */ +#define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ +#define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ +#define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ +#define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ +#define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +/* PCIE1 - VPX P1 */ +#define CONFIG_SYS_PCIE1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ + +/* PCIE2 - PEX8518 */ +#define CONFIG_SYS_PCIE2_MEM_BASE 0xc0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ + +/* + * Networking options + */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_TSEC_TBI +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_ETHPRIME "eTSEC2" + +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC1_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define CONFIG_HAS_ETH0 + +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_PHY_ADDR 2 +#define TSEC2_PHYIDX 0 +#define CONFIG_HAS_ETH1 + +/* + * Command configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DS4510 +#define CONFIG_CMD_DS4510_INFO +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ENV +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCA953X +#define CONFIG_CMD_PCA953X_INFO +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_SNTP + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ +#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ +#define CONFIG_PANIC_HANG /* do not reset board on panic */ +#define CONFIG_PREBOOT /* enable preboot variable */ +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 +#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ + +/* + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ +#define CONFIG_ENV_SIZE 0x8000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) + +/* + * Flash memory map: + * fff80000 - ffffffff Pri U-Boot (512 KB) + * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) + * fff00000 - fff3ffff Pri FDT (256KB) + * fef00000 - ffefffff Pri OS image (16MB) + * f8000000 - feefffff Pri OS Use/Filesystem (111MB) + * + * f7f80000 - f7ffffff Sec U-Boot (512 KB) + * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) + * f7f00000 - f7f3ffff Sec FDT (256KB) + * f6f00000 - f7efffff Sec OS image (16MB) + * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) + */ +#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000) +#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000) +#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000) +#define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7f00000) +#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000) +#define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000) + +#define CONFIG_PROG_UBOOT1 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_UBOOT2 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_BOOT_OS_NET \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "if test -n $fdtaddr; then " \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "bootm $osaddr - $fdtaddr; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi; " \ + "else; " \ + "bootm $osaddr; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS1 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS2 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT1 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT2 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=yes\0" \ + "download_cmd=tftp\0" \ + "console_args=console=ttyS0,115200\0" \ + "root_args=root=/dev/nfs rw\0" \ + "misc_args=ip=on\0" \ + "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ + "bootfile=/home/user/file\0" \ + "osfile=/home/user/uImage-XPedite5370\0" \ + "fdtfile=/home/user/xpedite5370.dtb\0" \ + "ubootfile=/home/user/u-boot.bin\0" \ + "fdtaddr=c00000\0" \ + "osaddr=0x1000000\0" \ + "loadaddr=0x1000000\0" \ + "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ + "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ + "prog_os1="CONFIG_PROG_OS1"\0" \ + "prog_os2="CONFIG_PROG_OS2"\0" \ + "prog_fdt1="CONFIG_PROG_FDT1"\0" \ + "prog_fdt2="CONFIG_PROG_FDT2"\0" \ + "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ + "bootcmd_flash1=run set_bootargs; " \ + "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ + "bootcmd_flash2=run set_bootargs; " \ + "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ + "bootcmd=run bootcmd_flash1\0" +#endif /* __CONFIG_H */ -- cgit v1.2.3 From 487dcb4fb89be0992bc06ec1341090017bd9cf2f Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Wed, 29 Oct 2008 12:39:27 -0500 Subject: 85xx: Enable inbound PCI config cycles for X-ES boards Update X-ES Freescale boards to allow inbound PCI configuration cycles when configured as agent/endpoint. Signed-off-by: Peter Tyser --- board/xes/common/fsl_85xx_pci.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/board/xes/common/fsl_85xx_pci.c b/board/xes/common/fsl_85xx_pci.c index b8e363ec9..4b048814e 100644 --- a/board/xes/common/fsl_85xx_pci.c +++ b/board/xes/common/fsl_85xx_pci.c @@ -29,6 +29,7 @@ #include extern int fsl_pci_setup_inbound_windows(struct pci_region *r); +extern void fsl_pci_config_unlock(struct pci_controller *hose); extern void fsl_pci_init(struct pci_controller *hose); int first_free_busno = 0; @@ -138,6 +139,10 @@ void pci_init_board(void) fsl_pci_init(hose); + /* Unlock inbound PCI configuration cycles */ + if (!host) + fsl_pci_config_unlock(hose); + first_free_busno = hose->last_busno+1; printf(" PCIE1 on bus %02x - %02x\n", hose->first_busno, hose->last_busno); @@ -187,6 +192,11 @@ void pci_init_board(void) (int)&pci->cfg_data); fsl_pci_init(hose); + + /* Unlock inbound PCI configuration cycles */ + if (!host) + fsl_pci_config_unlock(hose); + first_free_busno = hose->last_busno+1; printf(" PCIE2 on bus %02x - %02x\n", hose->first_busno, hose->last_busno); @@ -237,6 +247,11 @@ void pci_init_board(void) (int)&pci->cfg_data); fsl_pci_init(hose); + + /* Unlock inbound PCI configuration cycles */ + if (!host) + fsl_pci_config_unlock(hose); + first_free_busno = hose->last_busno+1; printf(" PCIE3 on bus %02x - %02x\n", hose->first_busno, hose->last_busno); -- cgit v1.2.3 From 78bbc5ce151c5a484bb51bf1866b4a993ffc16ec Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Mon, 1 Dec 2008 13:47:13 -0600 Subject: XPedite5200 board support Initial support for Extreme Engineering Solutions XPedite5200 - a MPC8548-based PMC single board computer. Signed-off-by: Peter Tyser --- MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 3 ++ board/xes/common/Makefile | 3 +- board/xes/common/fsl_85xx_pci.c | 103 ++++++++++++++++++++++++++++++++++++++-- 5 files changed, 106 insertions(+), 5 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index be10eb49a..60def0c34 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -413,6 +413,7 @@ Rune Torgersen Peter Tyser + XPEDITE5200 MPC8548 XPEDITE5370 MPC8572 David Updegraff diff --git a/MAKEALL b/MAKEALL index a136bad7a..5ce3f3112 100755 --- a/MAKEALL +++ b/MAKEALL @@ -385,6 +385,7 @@ LIST_85xx=" \ TQM8548 \ TQM8555 \ TQM8560 \ + XPEDITE5200 \ XPEDITE5370 \ " diff --git a/Makefile b/Makefile index 752a37066..c532e5b14 100644 --- a/Makefile +++ b/Makefile @@ -2463,6 +2463,9 @@ TQM8560_config: unconfig echo "#define CONFIG_BOARDNAME \"TQM$${CTYPE}\"">>$(obj)include/config.h; @$(MKCONFIG) -a TQM85xx ppc mpc85xx tqm85xx tqc +XPEDITE5200_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc mpc85xx xpedite5200 xes + XPEDITE5370_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc85xx xpedite5370 xes diff --git a/board/xes/common/Makefile b/board/xes/common/Makefile index c5cd6331e..e7620f447 100644 --- a/board/xes/common/Makefile +++ b/board/xes/common/Makefile @@ -29,9 +29,10 @@ endif LIB = $(obj)lib$(VENDOR).a +COBJS-$(CONFIG_FSL_PCI_INIT) += fsl_85xx_pci.o COBJS-$(CONFIG_MPC8572) += fsl_8572_clk.o COBJS-$(CONFIG_MPC85xx) += fsl_85xx_ddr.o -COBJS-$(CONFIG_FSL_PCI_INIT) += fsl_85xx_pci.o +COBJS-$(CONFIG_NAND_ACTL) += actl_nand.o SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(COBJS-y)) diff --git a/board/xes/common/fsl_85xx_pci.c b/board/xes/common/fsl_85xx_pci.c index 4b048814e..56f344795 100644 --- a/board/xes/common/fsl_85xx_pci.c +++ b/board/xes/common/fsl_85xx_pci.c @@ -34,6 +34,9 @@ extern void fsl_pci_init(struct pci_controller *hose); int first_free_busno = 0; +#ifdef CONFIG_PCI1 +static struct pci_controller pci1_hose; +#endif #ifdef CONFIG_PCIE1 static struct pci_controller pcie1_hose; #endif @@ -44,6 +47,7 @@ static struct pci_controller pcie2_hose; static struct pci_controller pcie3_hose; #endif +#ifdef CONFIG_MPC8572 /* Correlate host/agent POR bits to usable info. Table 4-14 */ struct host_agent_cfg_t { uchar pcie_root[3]; @@ -81,6 +85,38 @@ struct io_port_cfg_t { {{0, 0, 0}, 4}, {{8, 0, 0}, 0}, }; +#elif defined CONFIG_MPC8548 +/* Correlate host/agent POR bits to usable info. Table 4-12 */ +struct host_agent_cfg_t { + uchar pci_host[2]; + uchar pcie_root[1]; + uchar rio_host; +} host_agent_cfg[8] = { + {{1, 1}, {0}, 0}, + {{1, 1}, {1}, 0}, + {{1, 1}, {0}, 1}, + {{0, 0}, {0}, 0}, /* reserved */ + {{0, 1}, {1}, 0}, + {{1, 1}, {1}, 0}, + {{0, 1}, {1}, 1}, + {{1, 1}, {1}, 1} +}; + +/* Correlate port width POR bits to usable info. Table 4-13 */ +struct io_port_cfg_t { + uchar pcie_width[1]; + uchar rio_width; +} io_port_cfg[8] = { + {{0}, 0}, + {{0}, 0}, + {{0}, 0}, + {{4}, 4}, + {{4}, 4}, + {{0}, 4}, + {{0}, 4}, + {{8}, 0}, +}; +#endif void pci_init_board(void) { @@ -94,9 +130,65 @@ void pci_init_board(void) uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16; struct pci_region *r; - debug(" pci_init_board: devdisr=%x, io_sel=%x, host_agent=%x\n", - devdisr, io_sel, host_agent); +#ifdef CONFIG_PCI1 + uint pci_spd_norm = (gur->pordevsr & MPC85xx_PORDEVSR_PCI1_SPD); + uint pci_32 = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_PCI32; + uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; + uint pcix = gur->pordevsr & MPC85xx_PORDEVSR_PCI1; + uint freq = CONFIG_SYS_CLK_FREQ / 1000 / 1000; + + width = 0; /* Silence compiler warning... */ + io_sel &= 0xf; /* Silence compiler warning... */ + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR; + hose = &pci1_hose; + host = host_agent_cfg[host_agent].pci_host[0]; + r = hose->regions; + + + if (!(devdisr & MPC85xx_DEVDISR_PCI1)) { + printf("\n PCI1: %d bit %s, %s %d MHz, %s, %s\n", + pci_32 ? 32 : 64, + pcix ? "PCIX" : "PCI", + pci_spd_norm ? ">=" : "<=", + pcix ? freq * 2 : freq, + host ? "host" : "agent", + pci_arb ? "arbiter" : "external-arbiter"); + /* inbound */ + r += fsl_pci_setup_inbound_windows(r); + + /* outbound memory */ + pci_set_region(r++, + CONFIG_SYS_PCI1_MEM_BASE, + CONFIG_SYS_PCI1_MEM_PHYS, + CONFIG_SYS_PCI1_MEM_SIZE, + PCI_REGION_MEM); + + /* outbound io */ + pci_set_region(r++, + CONFIG_SYS_PCI1_IO_BASE, + CONFIG_SYS_PCI1_IO_PHYS, + CONFIG_SYS_PCI1_IO_SIZE, + PCI_REGION_IO); + + hose->region_count = r - hose->regions; + + hose->first_busno = first_free_busno; + pci_setup_indirect(hose, (int)&pci->cfg_addr, + (int)&pci->cfg_data); + + fsl_pci_init(hose); + + first_free_busno = hose->last_busno+1; + printf(" PCI1 on bus %02x - %02x\n", + hose->first_busno, hose->last_busno); + } else { + printf(" PCI1: disabled\n"); + } +#elif defined CONFIG_MPC8548 + /* PCI1 not present on MPC8572 */ + gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */ +#endif #ifdef CONFIG_PCIE1 pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; hose = &pcie1_hose; @@ -143,7 +235,7 @@ void pci_init_board(void) if (!host) fsl_pci_config_unlock(hose); - first_free_busno = hose->last_busno+1; + first_free_busno = hose->last_busno + 1; printf(" PCIE1 on bus %02x - %02x\n", hose->first_busno, hose->last_busno); } @@ -200,7 +292,6 @@ void pci_init_board(void) first_free_busno = hose->last_busno+1; printf(" PCIE2 on bus %02x - %02x\n", hose->first_busno, hose->last_busno); - } #else gur->devdisr |= MPC85xx_DEVDISR_PCIE2; /* disable */ @@ -267,6 +358,10 @@ extern void ft_fsl_pci_setup(void *blob, const char *pci_alias, void ft_board_pci_setup(void *blob, bd_t *bd) { + /* TODO - make node name (eg pci0) dynamic */ +#ifdef CONFIG_PCI1 + ft_fsl_pci_setup(blob, "pci0", &pci1_hose); +#endif #ifdef CONFIG_PCIE1 ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); #endif -- cgit v1.2.3 From ecf5b98c7a6a2e2256dfddd48fab26678dcd6b90 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 16 Dec 2008 14:59:20 -0600 Subject: 85xx: Add support to populate addr map based on TLB settings Signed-off-by: Kumar Gala --- cpu/mpc85xx/tlb.c | 34 ++++++++++++++++++++++++++++++++++ include/asm-ppc/mmu.h | 3 +++ lib_ppc/board.c | 8 ++++++++ 3 files changed, 45 insertions(+) diff --git a/cpu/mpc85xx/tlb.c b/cpu/mpc85xx/tlb.c index a2d16ae2f..5b5f7914f 100644 --- a/cpu/mpc85xx/tlb.c +++ b/cpu/mpc85xx/tlb.c @@ -26,6 +26,11 @@ #include #include #include +#ifdef CONFIG_ADDR_MAP +#include +#endif + +DECLARE_GLOBAL_DATA_PTR; void set_tlb(u8 tlb, u32 epn, u64 rpn, u8 perms, u8 wimge, @@ -47,6 +52,11 @@ void set_tlb(u8 tlb, u32 epn, u64 rpn, mtspr(MAS7, _mas7); #endif asm volatile("isync;msync;tlbwe;isync"); + +#ifdef CONFIG_ADDR_MAP + if ((tlb == 1) && (gd->flags & GD_FLG_RELOC)) + addrmap_set_entry(epn, rpn, (1UL << ((tsize * 2) + 10)), esel); +#endif } void disable_tlb(u8 esel) @@ -67,6 +77,11 @@ void disable_tlb(u8 esel) mtspr(MAS7, _mas7); #endif asm volatile("isync;msync;tlbwe;isync"); + +#ifdef CONFIG_ADDR_MAP + if (gd->flags & GD_FLG_RELOC) + addrmap_set_entry(0, 0, 0, esel); +#endif } void invalidate_tlb(u8 tlb) @@ -91,6 +106,25 @@ void init_tlbs(void) return ; } +#ifdef CONFIG_ADDR_MAP +void init_addr_map(void) +{ + int i; + + for (i = 0; i < num_tlb_entries; i++) { + if (tlb_table[i].tlb == 0) + continue; + + addrmap_set_entry(tlb_table[i].epn, + tlb_table[i].rpn, + (1UL << ((tlb_table[i].tsize * 2) + 10)), + tlb_table[i].esel); + } + + return ; +} +#endif + unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg) { unsigned int tlb_size; diff --git a/include/asm-ppc/mmu.h b/include/asm-ppc/mmu.h index 8975e6c90..6d942d083 100644 --- a/include/asm-ppc/mmu.h +++ b/include/asm-ppc/mmu.h @@ -431,6 +431,9 @@ extern void set_tlb(u8 tlb, u32 epn, u64 rpn, extern void disable_tlb(u8 esel); extern void invalidate_tlb(u8 tlb); extern void init_tlbs(void); +#ifdef CONFIG_ADDR_MAP +extern void init_addr_map(void); +#endif extern unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg); #define SET_TLB_ENTRY(_tlb, _epn, _rpn, _perms, _wimge, _ts, _esel, _sz, _iprot) \ diff --git a/lib_ppc/board.c b/lib_ppc/board.c index 289a32a64..61c29b563 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -75,6 +75,10 @@ #include #endif +#ifdef CONFIG_ADDR_MAP +#include +#endif + #ifdef CONFIG_SYS_UPDATE_FLASH_SIZE extern int update_flash_size (int flash_size); #endif @@ -694,6 +698,10 @@ void board_init_r (gd_t *id, ulong dest_addr) */ trap_init (dest_addr); +#if defined(CONFIG_ADDR_MAP) && defined(CONFIG_E500) + init_addr_map(); +#endif + #if defined(CONFIG_BOARD_EARLY_INIT_R) board_early_init_r (); #endif -- cgit v1.2.3 From 77c8115b1f1871811633eae77a5a700fac1f0e50 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 16 Dec 2008 14:59:21 -0600 Subject: ppc: Use addrmap in virt_to_phys and map_physmem. If we have addr map support enabled use the mapping functions to implement virt_to_phys() and map_physmem(). Signed-off-by: Kumar Gala --- include/asm-ppc/io.h | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/include/asm-ppc/io.h b/include/asm-ppc/io.h index 64cb746b1..4ddad26e8 100644 --- a/include/asm-ppc/io.h +++ b/include/asm-ppc/io.h @@ -10,6 +10,10 @@ #include #include +#ifdef CONFIG_ADDR_MAP +#include +#endif + #define SIO_CONFIG_RA 0x398 #define SIO_CONFIG_RD 0x399 @@ -287,7 +291,11 @@ extern inline void out_be32(volatile unsigned __iomem *addr, int val) static inline void * map_physmem(phys_addr_t paddr, unsigned long len, unsigned long flags) { +#ifdef CONFIG_ADDR_MAP + return (void *)(addrmap_phys_to_virt(paddr)); +#else return (void *)((unsigned long)paddr); +#endif } /* @@ -300,7 +308,11 @@ static inline void unmap_physmem(void *vaddr, unsigned long flags) static inline phys_addr_t virt_to_phys(void * vaddr) { +#ifdef CONFIG_ADDR_MAP + return addrmap_virt_to_phys(vaddr); +#else return (phys_addr_t)((unsigned long)vaddr); +#endif } #endif -- cgit v1.2.3 From 9d94aff699eed38b286814fcbb335f3eb8516a0e Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 16 Dec 2008 14:59:22 -0600 Subject: NAND FSL elbc: Use virt_to_phys to determine which bank is in use The current code that determines which bank/chipselect is used for a given NAND instance only worked for 32-bit addresses and assumed a 1:1 mapping. This breaks in 36-bit physical configs. The proper way to handle this is to use the virt_to_phys() and BR_PHYS_ADDR() routinues to match the 34-bit lbc bus address with the the virtual address the NAND code uses. Signed-off-by: Kumar Gala Acked-by: Scott Wood --- drivers/mtd/nand/fsl_elbc_nand.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c index 367c7d7fc..3f318e02e 100644 --- a/drivers/mtd/nand/fsl_elbc_nand.c +++ b/drivers/mtd/nand/fsl_elbc_nand.c @@ -718,7 +718,7 @@ static void fsl_elbc_ctrl_init(void) int board_nand_init(struct nand_chip *nand) { struct fsl_elbc_mtd *priv; - uint32_t br, or; + uint32_t br = 0, or = 0; if (!elbc_ctrl) { fsl_elbc_ctrl_init(); @@ -737,11 +737,13 @@ int board_nand_init(struct nand_chip *nand) * if we could pass more than one datum to the NAND driver... */ for (priv->bank = 0; priv->bank < MAX_BANKS; priv->bank++) { + phys_addr_t base_addr = virt_to_phys(nand->IO_ADDR_R); + br = in_be32(&elbc_ctrl->regs->bank[priv->bank].br); or = in_be32(&elbc_ctrl->regs->bank[priv->bank].or); if ((br & BR_V) && (br & BR_MSEL) == BR_MS_FCM && - (br & or & BR_BA) == (phys_addr_t)nand->IO_ADDR_R) + (br & or & BR_BA) == BR_PHYS_ADDR(base_addr)) break; } -- cgit v1.2.3 From 58ec4866ed916c7e422f5107bb27b0822084728e Mon Sep 17 00:00:00 2001 From: Trent Piepho Date: Wed, 3 Dec 2008 15:16:38 -0800 Subject: mpc8[56]xx: Put localbus clock in device tree Export the localbus frequency in the device tree, the same way the CPU, TB, CCB, and various other frequencies are exported in their respective device tree nodes. Some localbus devices need this information to be programed correctly, so it makes sense to export it along with the other frequencies. Unfortunately, when someone wrote the localbus dts bindings, they didn't bother to define what the "compatible" property should be. So it seems no one was quite sure what to put in their dts files. Based on current existing dts files in the kernel source, I've used "fsl,pq3-localbus" and "fsl,elbc" for MPC85xx, which are used by almost all of the 85xx devices, and are looked for by the Linux code. The eLBC is apparently not entirely backward compatible with the pq3 LBC and so eLBC equipped platforms like 8572 won't use pq3-localbus. For MPC86xx, I've used "fsl,elbc" which is used by some of the 86xx systems and is also looked for by the Linux code. On MPC8641, I've also used "fsl,mpc8641-localbus" as it is also commonly used in dts files, some of which don't use "fsl,elbc" or any other acceptable name to match on. Signed-off-by: Trent Piepho Acked-by: Kumar Gala Acked-by: Jon Loeliger --- cpu/mpc85xx/fdt.c | 8 +++++++- cpu/mpc86xx/fdt.c | 9 +++++++++ 2 files changed, 16 insertions(+), 1 deletion(-) diff --git a/cpu/mpc85xx/fdt.c b/cpu/mpc85xx/fdt.c index 59aafb1be..69fab9952 100644 --- a/cpu/mpc85xx/fdt.c +++ b/cpu/mpc85xx/fdt.c @@ -28,11 +28,12 @@ #include #include +DECLARE_GLOBAL_DATA_PTR; + extern void ft_qe_setup(void *blob); #ifdef CONFIG_MP #include "mp.h" -DECLARE_GLOBAL_DATA_PTR; void ft_fixup_cpu(void *blob, u64 memory_limit) { @@ -231,6 +232,11 @@ void ft_cpu_setup(void *blob, bd_t *bd) "clock-frequency", bd->bi_intfreq, 1); do_fixup_by_prop_u32(blob, "device_type", "soc", 4, "bus-frequency", bd->bi_busfreq, 1); + + do_fixup_by_compat_u32(blob, "fsl,pq3-localbus", + "bus-frequency", gd->lbc_clk, 1); + do_fixup_by_compat_u32(blob, "fsl,elbc", + "bus-frequency", gd->lbc_clk, 1); #ifdef CONFIG_QE ft_qe_setup(blob); #endif diff --git a/cpu/mpc86xx/fdt.c b/cpu/mpc86xx/fdt.c index 3adfad98c..e277040bb 100644 --- a/cpu/mpc86xx/fdt.c +++ b/cpu/mpc86xx/fdt.c @@ -13,6 +13,8 @@ DECLARE_GLOBAL_DATA_PTR; +DECLARE_GLOBAL_DATA_PTR; + void ft_cpu_setup(void *blob, bd_t *bd) { #if (CONFIG_NUM_CPUS > 1) @@ -29,6 +31,13 @@ void ft_cpu_setup(void *blob, bd_t *bd) do_fixup_by_prop_u32(blob, "device_type", "soc", 4, "bus-frequency", bd->bi_busfreq, 1); +#if defined(CONFIG_MPC8641) + do_fixup_by_compat_u32(blob, "fsl,mpc8641-localbus", + "bus-frequency", gd->lbc_clk, 1); +#endif + do_fixup_by_compat_u32(blob, "fsl,elbc", + "bus-frequency", gd->lbc_clk, 1); + fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); #if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) \ -- cgit v1.2.3 From a5d212a263c58cc746481bf1fc878510533ce7d6 Mon Sep 17 00:00:00 2001 From: Trent Piepho Date: Wed, 3 Dec 2008 15:16:34 -0800 Subject: mpc8xxx: LCRR[CLKDIV] is sometimes five bits On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits instead of four. In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It should be safe as the fifth bit was defined as reserved and set to 0. Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV. Signed-off-by: Trent Piepho Acked-by: Kumar Gala Acked-by: Jon Loeliger --- board/freescale/mpc8540ads/mpc8540ads.c | 2 +- board/freescale/mpc8541cds/mpc8541cds.c | 2 +- board/freescale/mpc8548cds/mpc8548cds.c | 2 +- board/freescale/mpc8555cds/mpc8555cds.c | 2 +- board/freescale/mpc8560ads/mpc8560ads.c | 2 +- board/freescale/mpc8568mds/mpc8568mds.c | 2 +- board/mpc8540eval/mpc8540eval.c | 2 +- board/pm854/pm854.c | 2 +- board/pm856/pm856.c | 2 +- board/sbc8548/sbc8548.c | 2 +- board/socrates/socrates.c | 2 +- board/tqc/tqm85xx/tqm85xx.c | 2 +- cpu/mpc85xx/cpu.c | 2 +- cpu/mpc86xx/cpu.c | 2 +- include/asm-ppc/fsl_lbc.h | 5 ++++- 15 files changed, 18 insertions(+), 15 deletions(-) diff --git a/board/freescale/mpc8540ads/mpc8540ads.c b/board/freescale/mpc8540ads/mpc8540ads.c index a0b6fbd12..9e3f67768 100644 --- a/board/freescale/mpc8540ads/mpc8540ads.c +++ b/board/freescale/mpc8540ads/mpc8540ads.c @@ -133,7 +133,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/freescale/mpc8541cds/mpc8541cds.c b/board/freescale/mpc8541cds/mpc8541cds.c index 7e40c5c80..e6025c8a5 100644 --- a/board/freescale/mpc8541cds/mpc8541cds.c +++ b/board/freescale/mpc8541cds/mpc8541cds.c @@ -308,7 +308,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/freescale/mpc8548cds/mpc8548cds.c b/board/freescale/mpc8548cds/mpc8548cds.c index c562fc9d9..90e89bc71 100644 --- a/board/freescale/mpc8548cds/mpc8548cds.c +++ b/board/freescale/mpc8548cds/mpc8548cds.c @@ -125,7 +125,7 @@ local_bus_init(void) sys_info_t sysinfo; get_sys_info(&sysinfo); - clkdiv = (lbc->lcrr & 0x0f) * 2; + clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; gur->lbiuiplldcr1 = 0x00078080; diff --git a/board/freescale/mpc8555cds/mpc8555cds.c b/board/freescale/mpc8555cds/mpc8555cds.c index 33685c19f..53d5a936a 100644 --- a/board/freescale/mpc8555cds/mpc8555cds.c +++ b/board/freescale/mpc8555cds/mpc8555cds.c @@ -308,7 +308,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/freescale/mpc8560ads/mpc8560ads.c b/board/freescale/mpc8560ads/mpc8560ads.c index 37308189d..ac7778e25 100644 --- a/board/freescale/mpc8560ads/mpc8560ads.c +++ b/board/freescale/mpc8560ads/mpc8560ads.c @@ -337,7 +337,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/freescale/mpc8568mds/mpc8568mds.c b/board/freescale/mpc8568mds/mpc8568mds.c index bc93be80f..7a23b338a 100644 --- a/board/freescale/mpc8568mds/mpc8568mds.c +++ b/board/freescale/mpc8568mds/mpc8568mds.c @@ -188,7 +188,7 @@ local_bus_init(void) sys_info_t sysinfo; get_sys_info(&sysinfo); - clkdiv = (lbc->lcrr & 0x0f) * 2; + clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; gur->lbiuiplldcr1 = 0x00078080; diff --git a/board/mpc8540eval/mpc8540eval.c b/board/mpc8540eval/mpc8540eval.c index fa0a33686..bf270f4ce 100644 --- a/board/mpc8540eval/mpc8540eval.c +++ b/board/mpc8540eval/mpc8540eval.c @@ -101,7 +101,7 @@ phys_size_t initdram (int board_type) #if !defined(CONFIG_RAM_AS_FLASH) /* LocalBus is not emulating flash */ get_sys_info(&sysinfo); /* if localbus freq is less than 66MHz,we use bypass mode,otherwise use DLL */ - if(sysinfo.freqSystemBus/(CONFIG_SYS_LBC_LCRR & 0x0f) < 66000000) { + if(sysinfo.freqSystemBus/(CONFIG_SYS_LBC_LCRR & LCRR_CLKDIV) < 66000000) { lbc->lcrr = (CONFIG_SYS_LBC_LCRR & 0x0fffffff)| 0x80000000; } else { lbc->lcrr = CONFIG_SYS_LBC_LCRR & 0x7fffffff; diff --git a/board/pm854/pm854.c b/board/pm854/pm854.c index fed0ed431..5353d738b 100644 --- a/board/pm854/pm854.c +++ b/board/pm854/pm854.c @@ -150,7 +150,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/pm856/pm856.c b/board/pm856/pm856.c index 932f1121e..b14a3d34b 100644 --- a/board/pm856/pm856.c +++ b/board/pm856/pm856.c @@ -306,7 +306,7 @@ local_bus_init(void) */ get_sys_info(&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; if (lbc_hz < 66) { diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c index 8c073cb4b..519b0f749 100644 --- a/board/sbc8548/sbc8548.c +++ b/board/sbc8548/sbc8548.c @@ -126,7 +126,7 @@ local_bus_init(void) sys_info_t sysinfo; get_sys_info(&sysinfo); - clkdiv = (lbc->lcrr & 0x0f) * 2; + clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2; lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; gur->lbiuiplldcr1 = 0x00078080; diff --git a/board/socrates/socrates.c b/board/socrates/socrates.c index d83dc7d6a..df9696e69 100644 --- a/board/socrates/socrates.c +++ b/board/socrates/socrates.c @@ -156,7 +156,7 @@ void local_bus_init (void) uint lcrr = CONFIG_SYS_LBC_LCRR; get_sys_info (&sysinfo); - clkdiv = lbc->lcrr & 0x0f; + clkdiv = lbc->lcrr & LCRR_CLKDIV; lbc_mhz = sysinfo.freqSystemBus / 1000000 / clkdiv; /* Disable PLL bypass for Local Bus Clock >= 66 MHz */ diff --git a/board/tqc/tqm85xx/tqm85xx.c b/board/tqc/tqm85xx/tqm85xx.c index 73f1d01bd..cda8208ee 100644 --- a/board/tqc/tqm85xx/tqm85xx.c +++ b/board/tqc/tqm85xx/tqm85xx.c @@ -361,7 +361,7 @@ uint get_lbc_clock (void) { volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); sys_info_t sys_info; - ulong clkdiv = lbc->lcrr & 0x0f; + ulong clkdiv = lbc->lcrr & LCRR_CLKDIV; get_sys_info (&sys_info); diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c index 943602f92..59a9ac8d9 100644 --- a/cpu/mpc85xx/cpu.c +++ b/cpu/mpc85xx/cpu.c @@ -174,7 +174,7 @@ int checkcpu (void) lcrr = lbc->lcrr; } #endif - clkdiv = lcrr & 0x0f; + clkdiv = lcrr & LCRR_CLKDIV; if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { #if defined(CONFIG_MPC8548) || defined(CONFIG_MPC8544) || \ defined(CONFIG_MPC8572) || defined(CONFIG_MPC8536) diff --git a/cpu/mpc86xx/cpu.c b/cpu/mpc86xx/cpu.c index 4cace984d..0ff76e3f7 100644 --- a/cpu/mpc86xx/cpu.c +++ b/cpu/mpc86xx/cpu.c @@ -110,7 +110,7 @@ checkcpu(void) lcrr = lbc->lcrr; } #endif - clkdiv = lcrr & 0x0f; + clkdiv = lcrr & LCRR_CLKDIV; if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { printf("LBC:%4lu MHz\n", sysinfo.freqSystemBus / 1000000 / clkdiv); diff --git a/include/asm-ppc/fsl_lbc.h b/include/asm-ppc/fsl_lbc.h index 51fc5c13b..e492c62a8 100644 --- a/include/asm-ppc/fsl_lbc.h +++ b/include/asm-ppc/fsl_lbc.h @@ -300,7 +300,10 @@ #define LCRR_EADC_2 0x00020000 #define LCRR_EADC_3 0x00030000 #define LCRR_EADC_4 0x00000000 -#define LCRR_CLKDIV 0x0000000F +/* CLKDIV is five bits only on 8536, 8572, and 8610, so far, but the fifth bit + * should always be zero on older parts that have a four bit CLKDIV. + */ +#define LCRR_CLKDIV 0x0000001F #define LCRR_CLKDIV_SHIFT 0 #define LCRR_CLKDIV_2 0x00000002 #define LCRR_CLKDIV_4 0x00000004 -- cgit v1.2.3 From 181a3650113883728927928b3ac81ad6dade4b2c Mon Sep 17 00:00:00 2001 From: Haiying Wang Date: Wed, 3 Dec 2008 10:08:19 -0500 Subject: Set IVPR to kenrel entry point in second core boot page Assuming the OSes exception vectors start from the base of kernel address, and the kernel physical starting address can be relocated to an non-zero address. This patch enables the second core to have a valid IVPR for debugger before kernel setting IVPR in CAMP mode. Otherwise, IVPR is 0x0 and it is not a valid value for second core which runs kernel at different physical address other than 0x0. Signed-off-by: Haiying Wang --- cpu/mpc85xx/release.S | 1 + 1 file changed, 1 insertion(+) diff --git a/cpu/mpc85xx/release.S b/cpu/mpc85xx/release.S index 7c3e8a172..54c936c3e 100644 --- a/cpu/mpc85xx/release.S +++ b/cpu/mpc85xx/release.S @@ -157,6 +157,7 @@ __secondary_start_page: mfspr r0,SPRN_PIR stw r0,ENTRY_PIR(r10) + mtspr IVPR,r12 /* * Coming here, we know the cpu has one TLB mapping in TLB1[0] * which maps 0xfffff000-0xffffffff one-to-one. We set up a -- cgit v1.2.3 From bd93105fa171184a71ca8b22be03dc2705cfbd3f Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Thu, 11 Dec 2008 15:47:49 -0500 Subject: sbc8548: don't enable the 3rd and 4th eTSEC These interfaces don't have usable connectors on the board, so don't bother enumerating or configuring them. Signed-off-by: Paul Gortmaker --- include/configs/sbc8548.h | 15 +-------------- 1 file changed, 1 insertion(+), 14 deletions(-) diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 528c81090..254d91f95 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -399,25 +399,16 @@ #define CONFIG_TSEC1_NAME "eTSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "eTSEC1" -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC2" -#define CONFIG_TSEC4 -#define CONFIG_TSEC4_NAME "eTSEC3" #undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 -#define TSEC3_PHY_ADDR 2 -#define TSEC4_PHY_ADDR 3 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -#define TSEC3_PHYIDX 0 -#define TSEC4_PHYIDX 0 + #define TSEC1_FLAGS TSEC_GIGABIT #define TSEC2_FLAGS TSEC_GIGABIT -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) /* Options are: eTSEC[0-3] */ #define CONFIG_ETHPRIME "eTSEC0" @@ -507,10 +498,6 @@ #define CONFIG_ETHADDR 02:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 02:E0:0C:00:01:FD -#define CONFIG_HAS_ETH2 -#define CONFIG_ETH2ADDR 02:E0:0C:00:02:FD -#define CONFIG_HAS_ETH3 -#define CONFIG_ETH3ADDR 02:E0:0C:00:03:FD #endif #define CONFIG_IPADDR 192.168.0.55 -- cgit v1.2.3 From ad22f9273c6f24fbfa917e867680e9688e0c59c5 Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Thu, 11 Dec 2008 15:47:51 -0500 Subject: sbc8548: enable command line editing by default. Lets make things a bit more user friendly. It isn't 1985 anymore. Signed-off-by: Paul Gortmaker --- include/configs/sbc8548.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 254d91f95..8a7b0da4d 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -455,6 +455,7 @@ /* * Miscellaneous configurable options */ +#define CONFIG_CMDLINE_EDITING /* undef to save memory */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -- cgit v1.2.3 From 58da8890d5fbd074746037722a423de9ac408616 Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Thu, 11 Dec 2008 15:47:50 -0500 Subject: sbc8548: use proper PHY address The values given for the PHY address were wrong, so the code read no valid PHY ID, and fell through to the generic PHY support, which would work on 1000M but would not auto negotiate down to 100M or 10M. Signed-off-by: Paul Gortmaker --- include/configs/sbc8548.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 8a7b0da4d..8141a46dc 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -401,8 +401,8 @@ #define CONFIG_TSEC2_NAME "eTSEC1" #undef CONFIG_MPC85XX_FEC -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHY_ADDR 0x19 +#define TSEC2_PHY_ADDR 0x1a #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -- cgit v1.2.3 From f51f07eb58fad12de9294ba4ee6c09a0ddeaee03 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Tue, 16 Dec 2008 12:09:27 +0800 Subject: 85xx: Fix the boot window issue If one custom board is using the 8MB flash, it is set as FLASH_BASE = 0xef000000, TEXT_BASE = 0xef780000. The current start.S code will be broken at switch_as. It is because the TLB1[15] is set as 16MB page size, EPN = TEXT_BASE & 0xff000000, RPN = 0xff000000. For the 8MB flash case, the EPN = 0xefxxxxxx, RPN = 0xffxxxxxx. Assume the virt address of switch_as is 0xef7ff18c, the real address of the instruction at switch_as should be 0xff7ff18c. the 0xff7ff18c is out of the range of the default 8MB boot LAW window 0xff800000 - 0xffffffff. So when we switch to AS1 address space at switch_as, the core can't fetch the instruction at switch_as any more. It will cause broken issue. Signed-off-by: Dave Liu --- cpu/mpc85xx/start.S | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/cpu/mpc85xx/start.S b/cpu/mpc85xx/start.S index 8fa0ff7a8..80f96773e 100644 --- a/cpu/mpc85xx/start.S +++ b/cpu/mpc85xx/start.S @@ -184,19 +184,19 @@ _start_e500: mtspr DBCR0,r0 #endif - /* create a temp mapping in AS=1 to the boot window */ + /* create a temp mapping in AS=1 to the 4M boot window */ lis r6,FSL_BOOKE_MAS0(1, 15, 0)@h ori r6,r6,FSL_BOOKE_MAS0(1, 15, 0)@l - lis r7,FSL_BOOKE_MAS1(1, 1, 0, 1, BOOKE_PAGESZ_16M)@h - ori r7,r7,FSL_BOOKE_MAS1(1, 1, 0, 1, BOOKE_PAGESZ_16M)@l + lis r7,FSL_BOOKE_MAS1(1, 1, 0, 1, BOOKE_PAGESZ_4M)@h + ori r7,r7,FSL_BOOKE_MAS1(1, 1, 0, 1, BOOKE_PAGESZ_4M)@l - /* Align the mapping to 16MB */ - lis r8,FSL_BOOKE_MAS2(TEXT_BASE & 0xff000000, (MAS2_I|MAS2_G))@h - ori r8,r8,FSL_BOOKE_MAS2(TEXT_BASE & 0xff000000, (MAS2_I|MAS2_G))@l + lis r8,FSL_BOOKE_MAS2(TEXT_BASE & 0xffc00000, (MAS2_I|MAS2_G))@h + ori r8,r8,FSL_BOOKE_MAS2(TEXT_BASE & 0xffc00000, (MAS2_I|MAS2_G))@l - lis r9,FSL_BOOKE_MAS3(0xff000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@h - ori r9,r9,FSL_BOOKE_MAS3(0xff000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@l + /* The 85xx has the default boot window 0xff800000 - 0xffffffff */ + lis r9,FSL_BOOKE_MAS3(0xffc00000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@h + ori r9,r9,FSL_BOOKE_MAS3(0xffc00000, 0, (MAS3_SX|MAS3_SW|MAS3_SR))@l mtspr MAS0,r6 mtspr MAS1,r7 -- cgit v1.2.3 From 446c381e3e16f19857b72ea0d06241267b8b9d58 Mon Sep 17 00:00:00 2001 From: Trent Piepho Date: Wed, 3 Dec 2008 15:16:35 -0800 Subject: mpc8568: Double local bus clock divider The clock divider for the MPC8568 local bus should be doubled, like the other newer MPC85xx chips. Since there are now more chips with a 2x divider than a 1x, and any new 85xx chips will probably be 2x, invert the sense of the #if so that it lists the 1x chips instead of the 2x ones. Signed-off-by: Trent Piepho Acked-by: Kumar Gala Acked-by: Jon Loeliger --- cpu/mpc85xx/cpu.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c index 59a9ac8d9..89800b884 100644 --- a/cpu/mpc85xx/cpu.c +++ b/cpu/mpc85xx/cpu.c @@ -176,8 +176,8 @@ int checkcpu (void) #endif clkdiv = lcrr & LCRR_CLKDIV; if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { -#if defined(CONFIG_MPC8548) || defined(CONFIG_MPC8544) || \ - defined(CONFIG_MPC8572) || defined(CONFIG_MPC8536) +#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8541) && \ + !defined(CONFIG_MPC8555) && !defined(CONFIG_MPC8560) /* * Yes, the entire PQ38 family use the same * bit-representation for twice the clock divider values. -- cgit v1.2.3 From 9863d6aca11405e1e0d8aba2045d78aeec4d4ee7 Mon Sep 17 00:00:00 2001 From: Trent Piepho Date: Wed, 3 Dec 2008 15:16:36 -0800 Subject: mpc86xx: Double local bus clock divider The local bus clock divider should be doubled for both 8610 and 8641. Signed-off-by: Trent Piepho Acked-by: Kumar Gala Acked-by: Jon Loeliger --- cpu/mpc86xx/cpu.c | 1 + 1 file changed, 1 insertion(+) diff --git a/cpu/mpc86xx/cpu.c b/cpu/mpc86xx/cpu.c index 0ff76e3f7..a179fb3d0 100644 --- a/cpu/mpc86xx/cpu.c +++ b/cpu/mpc86xx/cpu.c @@ -112,6 +112,7 @@ checkcpu(void) #endif clkdiv = lcrr & LCRR_CLKDIV; if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { + clkdiv *= 2; printf("LBC:%4lu MHz\n", sysinfo.freqSystemBus / 1000000 / clkdiv); } else { -- cgit v1.2.3 From ada591d2a0ecff5f9bc5ed1ebf310f439c3d0a28 Mon Sep 17 00:00:00 2001 From: Trent Piepho Date: Wed, 3 Dec 2008 15:16:37 -0800 Subject: mpc8[56]xx: Put localbus clock in sysinfo and gd Currently MPC85xx and MPC86xx boards just calculate the localbus frequency and print it out, but don't save it. This changes where its calculated and stored to be more consistent with the CPU, CCB, TB, and DDR frequencies and the MPC83xx localbus clock. The localbus frequency is added to sysinfo and calculated when sysinfo is set up, in cpu/mpc8[56]xx/speed.c, the same as the other frequencies are. get_clocks() copies the frequency into the global data, as the other frequencies are, into a new field that is only enabled for MPC85xx and MPC86xx. checkcpu() in cpu/mpc8[56]xx/cpu.c will print out the local bus frequency from sysinfo, like the other frequencies, instead of calculating it on the spot. Signed-off-by: Trent Piepho Acked-by: Kumar Gala Acked-by: Jon Loeliger --- cpu/mpc85xx/cpu.c | 31 +++++-------------------------- cpu/mpc85xx/speed.c | 27 +++++++++++++++++++++++++++ cpu/mpc86xx/cpu.c | 22 ++++------------------ cpu/mpc86xx/speed.c | 19 +++++++++++++++++++ include/asm-ppc/global_data.h | 3 +++ include/e500.h | 1 + include/mpc86xx.h | 1 + 7 files changed, 60 insertions(+), 44 deletions(-) diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c index 89800b884..15ba7f1c5 100644 --- a/cpu/mpc85xx/cpu.c +++ b/cpu/mpc85xx/cpu.c @@ -77,8 +77,6 @@ struct cpu_type *identify_cpu(u32 ver) int checkcpu (void) { sys_info_t sysinfo; - uint lcrr; /* local bus clock ratio register */ - uint clkdiv; /* clock divider portion of lcrr */ uint pvr, svr; uint fam; uint ver; @@ -165,30 +163,11 @@ int checkcpu (void) break; } -#if defined(CONFIG_SYS_LBC_LCRR) - lcrr = CONFIG_SYS_LBC_LCRR; -#else - { - volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); - - lcrr = lbc->lcrr; - } -#endif - clkdiv = lcrr & LCRR_CLKDIV; - if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { -#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8541) && \ - !defined(CONFIG_MPC8555) && !defined(CONFIG_MPC8560) - /* - * Yes, the entire PQ38 family use the same - * bit-representation for twice the clock divider values. - */ - clkdiv *= 2; -#endif - printf("LBC:%-4s MHz\n", - strmhz(buf1, sysinfo.freqSystemBus / clkdiv)); - } else { - printf("LBC: unknown (lcrr: 0x%08x)\n", lcrr); - } + if (sysinfo.freqLocalBus > LCRR_CLKDIV) + printf("LBC:%-4s MHz\n", strmhz(buf1, sysinfo.freqLocalBus)); + else + printf("LBC: unknown (LCRR[CLKDIV] = 0x%02lx)\n", + sysinfo.freqLocalBus); #ifdef CONFIG_CPM2 printf("CPM: %s MHz\n", strmhz(buf1, sysinfo.freqSystemBus)); diff --git a/cpu/mpc85xx/speed.c b/cpu/mpc85xx/speed.c index 1e0f4838b..0d55228b6 100644 --- a/cpu/mpc85xx/speed.c +++ b/cpu/mpc85xx/speed.c @@ -28,6 +28,7 @@ #include #include #include +#include DECLARE_GLOBAL_DATA_PTR; @@ -37,6 +38,7 @@ void get_sys_info (sys_info_t * sysInfo) { volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); uint plat_ratio,e500_ratio,half_freqSystemBus; + uint lcrr_div; plat_ratio = (gur->porpllsr) & 0x0000003e; plat_ratio >>= 1; @@ -60,6 +62,30 @@ void get_sys_info (sys_info_t * sysInfo) sysInfo->freqDDRBus = ddr_ratio * CONFIG_DDR_CLK_FREQ; } #endif + +#if defined(CONFIG_SYS_LBC_LCRR) + /* We will program LCRR to this value later */ + lcrr_div = CONFIG_SYS_LBC_LCRR & LCRR_CLKDIV; +#else + { + volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); + lcrr_div = in_be32(&lbc->lcrr) & LCRR_CLKDIV; + } +#endif + if (lcrr_div == 2 || lcrr_div == 4 || lcrr_div == 8) { +#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8541) && \ + !defined(CONFIG_MPC8555) && !defined(CONFIG_MPC8560) + /* + * Yes, the entire PQ38 family use the same + * bit-representation for twice the clock divider values. + */ + lcrr_div *= 2; +#endif + sysInfo->freqLocalBus = sysInfo->freqSystemBus / lcrr_div; + } else { + /* In case anyone cares what the unknown value is */ + sysInfo->freqLocalBus = lcrr_div; + } } @@ -82,6 +108,7 @@ int get_clocks (void) gd->cpu_clk = sys_info.freqProcessor; gd->bus_clk = sys_info.freqSystemBus; gd->mem_clk = sys_info.freqDDRBus; + gd->lbc_clk = sys_info.freqLocalBus; /* * The base clock for I2C depends on the actual SOC. Unfortunately, diff --git a/cpu/mpc86xx/cpu.c b/cpu/mpc86xx/cpu.c index a179fb3d0..35680238d 100644 --- a/cpu/mpc86xx/cpu.c +++ b/cpu/mpc86xx/cpu.c @@ -39,8 +39,6 @@ checkcpu(void) uint pvr, svr; uint ver; uint major, minor; - uint lcrr; /* local bus clock ratio register */ - uint clkdiv; /* clock divider portion of lcrr */ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; volatile ccsr_gur_t *gur = &immap->im_gur; @@ -100,23 +98,11 @@ checkcpu(void) printf("MPX:%4lu MHz, ", sysinfo.freqSystemBus / 1000000); printf("DDR:%4lu MHz, ", sysinfo.freqSystemBus / 2000000); -#if defined(CONFIG_SYS_LBC_LCRR) - lcrr = CONFIG_SYS_LBC_LCRR; -#else - { - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile ccsr_lbc_t *lbc = &immap->im_lbc; - - lcrr = lbc->lcrr; - } -#endif - clkdiv = lcrr & LCRR_CLKDIV; - if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { - clkdiv *= 2; - printf("LBC:%4lu MHz\n", - sysinfo.freqSystemBus / 1000000 / clkdiv); + if (sysinfo.freqLocalBus > LCRR_CLKDIV) { + printf("LBC:%4lu MHz\n", sysinfo.freqLocalBus / 1000000); } else { - printf(" LBC: unknown (lcrr: 0x%08x)\n", lcrr); + printf("LBC: unknown (LCRR[CLKDIV] = 0x%02x)\n", + sysinfo.freqLocalBus); } puts(" L2: "); diff --git a/cpu/mpc86xx/speed.c b/cpu/mpc86xx/speed.c index 415ac9db8..64a3479d7 100644 --- a/cpu/mpc86xx/speed.c +++ b/cpu/mpc86xx/speed.c @@ -28,6 +28,7 @@ #include #include #include +#include DECLARE_GLOBAL_DATA_PTR; @@ -39,6 +40,7 @@ void get_sys_info(sys_info_t *sysInfo) volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; volatile ccsr_gur_t *gur = &immap->im_gur; uint plat_ratio, e600_ratio; + uint lcrr_div; plat_ratio = (gur->porpllsr) & 0x0000003e; plat_ratio >>= 1; @@ -90,6 +92,22 @@ void get_sys_info(sys_info_t *sysInfo) sysInfo->freqProcessor = e600_ratio + sysInfo->freqSystemBus; break; } + +#if defined(CONFIG_SYS_LBC_LCRR) + /* We will program LCRR to this value later */ + lcrr_div = CONFIG_SYS_LBC_LCRR & LCRR_CLKDIV; +#else + { + volatile ccsr_lbc_t *lbc = &immap->im_lbc; + lcrr_div = in_be32(&lbc->lcrr) & LCRR_CLKDIV; + } +#endif + if (lcrr_div == 2 || lcrr_div == 4 || lcrr_div == 8) { + sysInfo->freqLocalBus = sysInfo->freqSystemBus / (lcrr_div * 2); + } else { + /* In case anyone cares what the unknown value is */ + sysInfo->freqLocalBus = lcrr_div; + } } @@ -105,6 +123,7 @@ int get_clocks(void) get_sys_info(&sys_info); gd->cpu_clk = sys_info.freqProcessor; gd->bus_clk = sys_info.freqSystemBus; + gd->lbc_clk = sys_info.freqLocalBus; /* * The base clock for I2C depends on the actual SOC. Unfortunately, diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index aade097fa..2bb50b47f 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -89,6 +89,9 @@ typedef struct global_data { #if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8536) u32 sdhc_clk; #endif +#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) + u32 lbc_clk; +#endif /* CONFIG_MPC85xx || CONFIG_MPC86xx */ #if defined(CONFIG_MPC83XX) || defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) u32 i2c1_clk; u32 i2c2_clk; diff --git a/include/e500.h b/include/e500.h index 1971eee29..9d3c8417c 100644 --- a/include/e500.h +++ b/include/e500.h @@ -13,6 +13,7 @@ typedef struct unsigned long freqProcessor; unsigned long freqSystemBus; unsigned long freqDDRBus; + unsigned long freqLocalBus; } MPC85xx_SYS_INFO; #endif /* _ASMLANGUAGE */ diff --git a/include/mpc86xx.h b/include/mpc86xx.h index f119d5bb1..a6fdea352 100644 --- a/include/mpc86xx.h +++ b/include/mpc86xx.h @@ -84,6 +84,7 @@ typedef struct { unsigned long freqProcessor; unsigned long freqSystemBus; + unsigned long freqLocalBus; } MPC86xx_SYS_INFO; #define l1icache_enable icache_enable -- cgit v1.2.3 From 1f03cbfae221b24ba1341a0a3f62ff01c5c874df Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Tue, 23 Dec 2008 16:32:00 -0600 Subject: XPedite5200 board support cleanup Signed-off-by: Peter Tyser --- board/xes/common/actl_nand.c | 65 +++++ board/xes/common/fsl_85xx_pci.c | 6 +- board/xes/xpedite5200/Makefile | 55 ++++ board/xes/xpedite5200/config.mk | 34 +++ board/xes/xpedite5200/ddr.c | 91 ++++++ board/xes/xpedite5200/law.c | 51 ++++ board/xes/xpedite5200/tlb.c | 85 ++++++ board/xes/xpedite5200/u-boot.lds | 145 ++++++++++ board/xes/xpedite5200/xpedite5200.c | 125 +++++++++ include/configs/XPEDITE5200.h | 546 ++++++++++++++++++++++++++++++++++++ 10 files changed, 1200 insertions(+), 3 deletions(-) create mode 100644 board/xes/common/actl_nand.c create mode 100644 board/xes/xpedite5200/Makefile create mode 100644 board/xes/xpedite5200/config.mk create mode 100644 board/xes/xpedite5200/ddr.c create mode 100644 board/xes/xpedite5200/law.c create mode 100644 board/xes/xpedite5200/tlb.c create mode 100644 board/xes/xpedite5200/u-boot.lds create mode 100644 board/xes/xpedite5200/xpedite5200.c create mode 100644 include/configs/XPEDITE5200.h diff --git a/board/xes/common/actl_nand.c b/board/xes/common/actl_nand.c new file mode 100644 index 000000000..465aeb099 --- /dev/null +++ b/board/xes/common/actl_nand.c @@ -0,0 +1,65 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * This driver support NAND devices which have address lines + * connected as ALE and CLE inputs. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/* + * Hardware specific access to control-lines + */ +static void nand_addr_hwcontrol(struct mtd_info *mtd, int cmd, uint ctrl) +{ + struct nand_chip *this = mtd->priv; + ulong IO_ADDR_W; + + if (ctrl & NAND_CTRL_CHANGE) { + IO_ADDR_W = (ulong)this->IO_ADDR_W; + + IO_ADDR_W &= ~(CONFIG_SYS_NAND_ACTL_CLE | + CONFIG_SYS_NAND_ACTL_ALE | + CONFIG_SYS_NAND_ACTL_NCE); + if (ctrl & NAND_CLE) + IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_CLE; + if (ctrl & NAND_ALE) + IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_ALE; + if (ctrl & NAND_NCE) + IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_NCE; + + this->IO_ADDR_W = (void *)IO_ADDR_W; + } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); +} + +int board_nand_init(struct nand_chip *nand) +{ + nand->ecc.mode = NAND_ECC_SOFT; + nand->cmd_ctrl = nand_addr_hwcontrol; + nand->chip_delay = CONFIG_SYS_NAND_ACTL_DELAY; + + return 0; +} diff --git a/board/xes/common/fsl_85xx_pci.c b/board/xes/common/fsl_85xx_pci.c index 56f344795..cd65a7341 100644 --- a/board/xes/common/fsl_85xx_pci.c +++ b/board/xes/common/fsl_85xx_pci.c @@ -179,7 +179,7 @@ void pci_init_board(void) fsl_pci_init(hose); - first_free_busno = hose->last_busno+1; + first_free_busno = hose->last_busno + 1; printf(" PCI1 on bus %02x - %02x\n", hose->first_busno, hose->last_busno); } else { @@ -289,7 +289,7 @@ void pci_init_board(void) if (!host) fsl_pci_config_unlock(hose); - first_free_busno = hose->last_busno+1; + first_free_busno = hose->last_busno + 1; printf(" PCIE2 on bus %02x - %02x\n", hose->first_busno, hose->last_busno); } @@ -343,7 +343,7 @@ void pci_init_board(void) if (!host) fsl_pci_config_unlock(hose); - first_free_busno = hose->last_busno+1; + first_free_busno = hose->last_busno + 1; printf(" PCIE3 on bus %02x - %02x\n", hose->first_busno, hose->last_busno); } diff --git a/board/xes/xpedite5200/Makefile b/board/xes/xpedite5200/Makefile new file mode 100644 index 000000000..02fe8fcd2 --- /dev/null +++ b/board/xes/xpedite5200/Makefile @@ -0,0 +1,55 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2004 Freescale Semiconductor. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS-y)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/xes/xpedite5200/config.mk b/board/xes/xpedite5200/config.mk new file mode 100644 index 000000000..be5a5c32c --- /dev/null +++ b/board/xes/xpedite5200/config.mk @@ -0,0 +1,34 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2004, 2007 Freescale Semiconductor. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# xpedite5200 board +# +ifndef TEXT_BASE +TEXT_BASE = 0xfff80000 +endif + +PLATFORM_CPPFLAGS += -DCONFIG_E500=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC8548=1 +PLATFORM_CPPFLAGS += -mrelocatable diff --git a/board/xes/xpedite5200/ddr.c b/board/xes/xpedite5200/ddr.c new file mode 100644 index 000000000..c5616d546 --- /dev/null +++ b/board/xes/xpedite5200/ddr.c @@ -0,0 +1,91 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include +#include + +#include +#include + +static void +get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address) +{ + i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t)); + + /* We use soldered memory, but use an SPD EEPROM to describe it. + * The SPD has an unspecified dimm type, but the DDR2 initialization + * code requires a specific type to be specified. This sets the type + * as a standard unregistered SO-DIMM. */ + if (spd->dimm_type == 0) { + spd->dimm_type = 0x4; + ((uchar *)spd)[63] += 0x4; + } +} + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_ddr_freq(0); +} + +void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd, + unsigned int ctrl_num) +{ + unsigned int i; + + if (ctrl_num) { + printf("%s: invalid ctrl_num = %d\n", __func__, ctrl_num); + return; + } + + for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) + get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS); +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + /* + * Factors to consider for clock adjust: + * - number of chips on bus + * - position of slot + * - DDR1 vs. DDR2? + * - ??? + * + * This needs to be determined on a board-by-board basis. + * 0110 3/4 cycle late + * 0111 7/8 cycle late + */ + popts->clk_adjust = 7; + + /* + * Factors to consider for CPO: + * - frequency + * - ddr1 vs. ddr2 + */ + popts->cpo_override = 9; + + /* + * Factors to consider for write data delay: + * - number of DIMMs + * + * 1 = 1/4 clock delay + * 2 = 1/2 clock delay + * 3 = 3/4 clock delay + * 4 = 1 clock delay + * 5 = 5/4 clock delay + * 6 = 3/2 clock delay + */ + popts->write_data_delay = 3; + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} diff --git a/board/xes/xpedite5200/law.c b/board/xes/xpedite5200/law.c new file mode 100644 index 000000000..386f9c587 --- /dev/null +++ b/board/xes/xpedite5200/law.c @@ -0,0 +1,51 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + /* LBC window - maps 256M 0xf0000000 -> 0xffffffff */ + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +#if CONFIG_SYS_PCI1_MEM_PHYS + SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_1G, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAWAR_SIZE_8M, LAW_TRGT_IF_PCI_1), +#endif +#if CONFIG_SYS_PCI2_MEM_PHYS + SET_LAW(CONFIG_SYS_PCI2_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCI_2), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/xes/xpedite5200/tlb.c b/board/xes/xpedite5200/tlb.c new file mode 100644 index 000000000..bd7bff820 --- /dev/null +++ b/board/xes/xpedite5200/tlb.c @@ -0,0 +1,85 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + +#if CONFIG_PCI1 + /* *I*G* - PCI MEM */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS, CONFIG_SYS_PCI1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), +#endif + +#if CONFIG_PCI2 + /* *I*G* - PCI MEM */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI2_MEM_PHYS, CONFIG_SYS_PCI2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCI1) || defined(CONFIG_PCI2) + /* *I*G* - PCI IO */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_IO_PHYS, CONFIG_SYS_PCI1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_16M, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/xes/xpedite5200/u-boot.lds b/board/xes/xpedite5200/u-boot.lds new file mode 100644 index 000000000..bd952d20f --- /dev/null +++ b/board/xes/xpedite5200/u-boot.lds @@ -0,0 +1,145 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2004, 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +PHDRS +{ + text PT_LOAD; + bss PT_LOAD; +} + +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + *(.text) + *(.got1) + } :text + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } :text + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + .bootpg ADDR(.text) + 0x7f000 : + { + cpu/mpc85xx/start.o (.bootpg) + } :text = 0xffff + + .resetvec ADDR(.text) + 0x7fffc : + { + *(.resetvec) + } :text = 0xffff + + . = ADDR(.text) + 0x80000; + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } :bss + + . = ALIGN(4); + _end = . ; + PROVIDE (end = .); +} diff --git a/board/xes/xpedite5200/xpedite5200.c b/board/xes/xpedite5200/xpedite5200.c new file mode 100644 index 000000000..e266d1dd8 --- /dev/null +++ b/board/xes/xpedite5200/xpedite5200.c @@ -0,0 +1,125 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2004, 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +int checkboard(void) +{ + volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); + volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR); + + char *s; + + printf("Board: X-ES %s PMC\n", CONFIG_SYS_BOARD_NAME); + printf(" "); + s = getenv("board_rev"); + if (s) + printf("Rev %s, ", s); + s = getenv("serial#"); + if (s) + printf("Serial# %s, ", s); + s = getenv("board_cfg"); + if (s) + printf("Cfg %s", s); + printf("\n"); + + lbc->ltesr = 0xffffffff; /* Clear LBC error interrupts */ + lbc->lteir = 0xffffffff; /* Enable LBC error interrupts */ + ecm->eedr = 0xffffffff; /* Clear ecm errors */ + ecm->eeer = 0xffffffff; /* Enable ecm errors */ + + return 0; +} + +static void flash_cs_fixup(void) +{ + volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR); + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_FLASH_PASS_CS)); + printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + lbc->br0 = CONFIG_SYS_BR1_PRELIM; + lbc->or0 = CONFIG_SYS_OR1_PRELIM; + + lbc->br1 = CONFIG_SYS_BR0_PRELIM; + lbc->or1 = CONFIG_SYS_OR0_PRELIM; + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif diff --git a/include/configs/XPEDITE5200.h b/include/configs/XPEDITE5200.h new file mode 100644 index 000000000..1df6855cc --- /dev/null +++ b/include/configs/XPEDITE5200.h @@ -0,0 +1,546 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2004-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * xpedite5200 board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8548 1 +#define CONFIG_XPEDITE5200 1 +#define CONFIG_SYS_BOARD_NAME "XPedite5200" +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ +#define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */ + +#define CONFIG_PCI 1 /* Enable PCI/PCIE */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CONFIG_PCI1 1 /* PCI controller 1 */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +/* + * DDR config + */ +#define CONFIG_FSL_DDR2 +#undef CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define SPD_EEPROM_ADDRESS 0x54 +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#define CONFIG_SYS_CLK_FREQ 66666666 + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ +#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000) + +/* + * Diagnostics + */ +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x20000000 + +/* + * Memory map + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * 0x8000_0000 0xbfff_ffff PCI1 Mem 1G non-cacheable + * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable + * 0xe800_0000 0xe87f_ffff PCI1 IO 8M non-cacheable + * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable + * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable + * 0xf800_0000 0xfbff_ffff NOR Flash 2 64M non-cacheable + * 0xfc00_0000 0xffff_ffff NOR Flash 1 64M non-cacheable + */ + +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3) + +/* + * NAND flash configuration + */ +#define CONFIG_SYS_NAND_BASE 0xef800000 +#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_NAND_ACTL +#define CONFIG_SYS_NAND_ACTL_CLE (1 << 3) /* ADDR3 is CLE */ +#define CONFIG_SYS_NAND_ACTL_ALE (1 << 4) /* ADDR4 is ALE */ +#define CONFIG_SYS_NAND_ACTL_NCE (0) /* NCE not controlled by ADDR */ +#define CONFIG_SYS_NAND_ACTL_DELAY 25 + +/* + * NOR flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xfc000000 +#define CONFIG_SYS_FLASH_BASE2 0xf8000000 +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ + {0xfbf40000, 0xc0000} } +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +/* + * Chip select configuration + */ +/* NOR Flash 0 on CS0 */ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR0_PRELIM (OR_AM_64MB | \ + OR_GPCM_ACS_DIV4 | \ + OR_GPCM_SCY_8) + +/* NOR Flash 1 on CS1 */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM + +/* NAND flash on CS2 */ +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ + BR_PS_8 | \ + BR_V) + +/* NAND flash on CS2 */ +#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ + OR_GPCM_BCTLD | \ + OR_GPCM_CSNT | \ + OR_GPCM_ACS_DIV4 | \ + OR_GPCM_SCY_4 | \ + OR_GPCM_TRLX | \ + OR_GPCM_EHTR) + +/* NAND flash on CS3 */ +#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ + BR_PS_8 | \ + BR_V) +#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM + +/* + * Use L1 as initial stack + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 +#define CONFIG_SYS_INIT_RAM_END 0x4000 + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} +#define CONFIG_BAUDRATE 115200 +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Use the HUSH parser + */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE + +/* I2C EEPROM */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ + +/* I2C RTC */ +#define CONFIG_RTC_M41T11 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 2000 + +/* GPIO */ +#define CONFIG_PCA953X +#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 +#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x19 +#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 + +/* PCA957 @ 0x18 */ +#define CONFIG_SYS_PCA953X_BRD_CFG0 0x01 +#define CONFIG_SYS_PCA953X_BRD_CFG1 0x02 +#define CONFIG_SYS_PCA953X_BRD_CFG2 0x04 +#define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08 +#define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10 +#define CONFIG_SYS_PCA953X_FLASH_WP 0x20 +#define CONFIG_SYS_PCA953X_MONARCH 0x40 +#define CONFIG_SYS_PCA953X_EREADY 0x80 + +/* PCA957 @ 0x19 */ +#define CONFIG_SYS_PCA953X_P14_IO0 0x01 +#define CONFIG_SYS_PCA953X_P14_IO1 0x02 +#define CONFIG_SYS_PCA953X_P14_IO2 0x04 +#define CONFIG_SYS_PCA953X_P14_IO3 0x08 +#define CONFIG_SYS_PCA953X_P14_IO4 0x10 +#define CONFIG_SYS_PCA953X_P14_IO5 0x20 +#define CONFIG_SYS_PCA953X_P14_IO6 0x40 +#define CONFIG_SYS_PCA953X_P14_IO7 0x80 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */ + +/* + * Networking options + */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC1_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define CONFIG_HAS_ETH0 + +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define TSEC2_FLAGS TSEC_GIGABIT +#define TSEC2_PHY_ADDR 2 +#define TSEC2_PHYIDX 0 +#define CONFIG_HAS_ETH1 + +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC3" +#define TSEC3_FLAGS TSEC_GIGABIT +#define TSEC3_PHY_ADDR 3 +#define TSEC3_PHYIDX 0 +#define CONFIG_HAS_ETH2 + +#define CONFIG_TSEC4 1 +#define CONFIG_TSEC4_NAME "eTSEC4" +#define TSEC4_FLAGS TSEC_GIGABIT +#define TSEC4_PHY_ADDR 4 +#define TSEC4_PHYIDX 0 +#define CONFIG_HAS_ETH3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY + +/* + * Command configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ENV +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCA953X +#define CONFIG_CMD_PCA953X_INFO +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_SNTP + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ +#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ +#define CONFIG_PANIC_HANG /* do not reset board on panic */ +#define CONFIG_PREBOOT /* enable preboot variable */ +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 +#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ +#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ + +/* + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ +#define CONFIG_ENV_SIZE 0x8000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) + +/* + * Flash memory map: + * fff80000 - ffffffff Pri U-Boot (512 KB) + * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) + * fff00000 - fff3ffff Pri FDT (256KB) + * fef00000 - ffefffff Pri OS image (16MB) + * fc000000 - feefffff Pri OS Use/Filesystem (47MB) + * + * fbf80000 - fbffffff Sec U-Boot (512 KB) + * fbf40000 - fbf7ffff Sec U-Boot Environment (256 KB) + * fbf00000 - fbf3ffff Sec FDT (256KB) + * faf00000 - fbefffff Sec OS image (16MB) + * f8000000 - faefffff Sec OS Use/Filesystem (47MB) + */ +#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000) +#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xfbf80000) +#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000) +#define CONFIG_FDT2_ENV_ADDR MK_STR(0xfbf00000) +#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000) +#define CONFIG_OS2_ENV_ADDR MK_STR(0xfaf00000) + +#define CONFIG_PROG_UBOOT1 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_UBOOT2 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_BOOT_OS_NET \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "if test -n $fdtaddr; then " \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "bootm $osaddr - $fdtaddr; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi; " \ + "else; " \ + "bootm $osaddr; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS1 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS2 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT1 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT2 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=yes\0" \ + "download_cmd=tftp\0" \ + "console_args=console=ttyS0,115200\0" \ + "root_args=root=/dev/nfs rw\0" \ + "misc_args=ip=on\0" \ + "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ + "bootfile=/home/user/file\0" \ + "osfile=/home/user/uImage-XPedite5200\0" \ + "fdtfile=/home/user/xpedite5200.dtb\0" \ + "ubootfile=/home/user/u-boot.bin\0" \ + "fdtaddr=c00000\0" \ + "osaddr=0x1000000\0" \ + "loadaddr=0x1000000\0" \ + "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ + "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ + "prog_os1="CONFIG_PROG_OS1"\0" \ + "prog_os2="CONFIG_PROG_OS2"\0" \ + "prog_fdt1="CONFIG_PROG_FDT1"\0" \ + "prog_fdt2="CONFIG_PROG_FDT2"\0" \ + "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ + "bootcmd_flash1=run set_bootargs; " \ + "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ + "bootcmd_flash2=run set_bootargs; " \ + "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ + "bootcmd=run bootcmd_flash1\0" +#endif /* __CONFIG_H */ -- cgit v1.2.3 From d9011f9b75561a0bd9254934c2bb2bc799d4f645 Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Tue, 23 Dec 2008 16:32:01 -0600 Subject: 85xx: Enable inbound PCI config cycles for X-ES boards cleanup Signed-off-by: Peter Tyser --- board/xes/common/fsl_85xx_pci.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/board/xes/common/fsl_85xx_pci.c b/board/xes/common/fsl_85xx_pci.c index cd65a7341..9673a02b5 100644 --- a/board/xes/common/fsl_85xx_pci.c +++ b/board/xes/common/fsl_85xx_pci.c @@ -179,6 +179,10 @@ void pci_init_board(void) fsl_pci_init(hose); + /* Unlock inbound PCI configuration cycles */ + if (!host) + fsl_pci_config_unlock(hose); + first_free_busno = hose->last_busno + 1; printf(" PCI1 on bus %02x - %02x\n", hose->first_busno, hose->last_busno); -- cgit v1.2.3