From 3bac351370ef7cbf9d2af27ba52bee1703ad677e Mon Sep 17 00:00:00 2001 From: wdenk Date: Wed, 12 Mar 2003 10:41:04 +0000 Subject: * Patch by Josef Wagner, 12 Mar 2003: - 16/32 MB and 50/80 MHz support with auto-detection for IP860 - ETH05 and BEDBUG support for CU824 - added support for MicroSys CPC45 - new BOOTROM/FLASH0 and DOC base for PM826 * Patch by Robert Schwebel, 12 Mar 2003: Fix the chpart command on innokom board * Name cleanup: mv include/asm-i386/ppcboot-i386.h include/asm-i386/u-boot-i386.h s/PPCBoot/U-Boot/ in some files s/pImage/uImage/ in some files * Patch by Detlev Zundel, 15 Jan 2003: Fix '' command line quoting * Patch by The LEOX team, 19 Jan 2003: - add support for the ELPT860 board - add support for Dallas ds164x RTC --- board/LEOX/elpt860/Makefile | 47 +++ board/LEOX/elpt860/README.LEOX | 424 +++++++++++++++++++++++++ board/LEOX/elpt860/config.mk | 36 +++ board/LEOX/elpt860/elpt860.c | 399 +++++++++++++++++++++++ board/LEOX/elpt860/flash.c | 615 ++++++++++++++++++++++++++++++++++++ board/LEOX/elpt860/u-boot.lds | 146 +++++++++ board/LEOX/elpt860/u-boot.lds.debug | 140 ++++++++ 7 files changed, 1807 insertions(+) create mode 100644 board/LEOX/elpt860/Makefile create mode 100644 board/LEOX/elpt860/README.LEOX create mode 100644 board/LEOX/elpt860/config.mk create mode 100644 board/LEOX/elpt860/elpt860.c create mode 100644 board/LEOX/elpt860/flash.c create mode 100644 board/LEOX/elpt860/u-boot.lds create mode 100644 board/LEOX/elpt860/u-boot.lds.debug (limited to 'board/LEOX') diff --git a/board/LEOX/elpt860/Makefile b/board/LEOX/elpt860/Makefile new file mode 100644 index 000000000..abca765d7 --- /dev/null +++ b/board/LEOX/elpt860/Makefile @@ -0,0 +1,47 @@ +####################################################################### +# +# Copyright (C) 2000, 2001, 2002, 2003 +# The LEOX team , http://www.leox.org +# +# LEOX.org is about the development of free hardware and software resources +# for system on chip. +# +# Description: U-Boot port on the LEOX's ELPT860 CPU board +# ~~~~~~~~~~~ +# +####################################################################### +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +####################################################################### + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS = $(BOARD).o flash.o + +$(LIB): .depend $(OBJS) + $(AR) crv $@ $^ + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +sinclude .depend + +######################################################################### diff --git a/board/LEOX/elpt860/README.LEOX b/board/LEOX/elpt860/README.LEOX new file mode 100644 index 000000000..9ace97b3e --- /dev/null +++ b/board/LEOX/elpt860/README.LEOX @@ -0,0 +1,424 @@ +============================================================================= + + U-Boot port on the LEOX's ELPT860 CPU board + ------------------------------------------- + +LEOX.org is about the development of free hardware and software resources + for system on chip. + +For more information, contact The LEOX team + +References: +~~~~~~~~~~ + 1) Get the last stable release from denx.de: + o ftp://ftp.denx.de/pub/u-boot/u-boot-0.2.0.tar.bz2 + 2) Get the current CVS snapshot: + o cvs -d:pserver:anonymous@cvs.u-boot.sourceforge.net:/cvsroot/u-boot login + o cvs -z6 -d:pserver:anonymous@cvs.u-boot.sourceforge.net:/cvsroot/u-boot co -P u-boot + +============================================================================= + +The ELPT860 CPU board has the following features: + +Processor: - MPC860T @ 50MHz + - PowerPC Core + - 65 MIPS + - Caches: D->4KB, I->4KB + - CPM: 4 SCCs, 2 SMCs + - Ethernet 10/100 + - SPI, I2C, PCMCIA, Parallel + +CPU board: - DRAM: 16 MB + - FLASH: 512 KB + (2 * 4 MB) + - NVRAM: 128 KB + - 1 Serial link + - 2 Ethernet 10 BaseT Channels + +On power-up the processor jumps to the address of 0x02000100 + +Thus, U-Boot is configured to reside in flash starting at the address of +0x02001000. The environment space is located in NVRAM separately from +U-Boot, at the address of 0x03000000. + +============================================================================= + + U-Boot test results + +============================================================================= + + +################################################## +# Operation on the serial console (SMC1) +############################## + +U-Boot 0.2.2 (Jan 19 2003 - 11:08:39) + +CPU: XPC860xxZPnnB at 50 MHz: 4 kB I-Cache 4 kB D-Cache FEC present + *** Warning: CPU Core has Silicon Bugs -- Check the Errata *** +Board: ### No HW ID - assuming ELPT860 +DRAM: 16 MB +FLASH: 512 kB +In: serial +Out: serial +Err: serial +Net: SCC ETHERNET + +Type "run nfsboot" to mount root filesystem over NFS + +Hit any key to stop autoboot: 0 +LEOX_elpt860: help +askenv - get environment variables from stdin +autoscr - run script from memory +base - print or set address offset +bdinfo - print Board Info structure +bootm - boot application image from memory +bootp - boot image via network using BootP/TFTP protocol +bootd - boot default, i.e., run 'bootcmd' +cmp - memory compare +coninfo - print console devices and informations +cp - memory copy +crc32 - checksum calculation +echo - echo args to console +erase - erase FLASH memory +flinfo - print FLASH memory information +go - start application at address 'addr' +help - print online help +iminfo - print header information for application image +loadb - load binary file over serial line (kermit mode) +loads - load S-Record file over serial line +loop - infinite loop on address range +md - memory display +mm - memory modify (auto-incrementing) +mtest - simple RAM test +mw - memory write (fill) +nm - memory modify (constant address) +printenv- print environment variables +protect - enable or disable FLASH write protection +rarpboot- boot image via network using RARP/TFTP protocol +reset - Perform RESET of the CPU +run - run commands in an environment variable +saveenv - save environment variables to persistent storage +setenv - set environment variables +sleep - delay execution for some time +tftpboot- boot image via network using TFTP protocol + and env variables ipaddr and serverip +version - print monitor version +? - alias for 'help' + +################################################## +# Environment Variables (CFG_ENV_IS_IN_NVRAM) +############################## + +LEOX_elpt860: printenv +bootdelay=5 +loads_echo=1 +baudrate=9600 +stdin=serial +stdout=serial +stderr=serial +ethaddr=00:03:ca:00:64:df +ipaddr=192.168.0.30 +netmask=255.255.255.0 +serverip=192.168.0.1 +nfsserverip=192.168.0.1 +preboot=echo;echo Type "run nfsboot" to mount root filesystem over NFS;echo +gatewayip=192.168.0.1 +ramargs=setenv bootargs root=/dev/ram rw +rootargs=setenv rootpath /tftp/$(ipaddr) +nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(nfsserverip):$(rootpath) +addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(nfsserverip):$(gatewayip):$(netmask):$(hostname):eth0: +ramboot=tftp 400000 /home/leox/pMulti;run ramargs;bootm +nfsboot=tftp 400000 /home/leox/uImage;run rootargs;run nfsargs;run addip;bootm +bootcmd=run ramboot +clocks_in_mhz=1 + +Environment size: 730/16380 bytes + +################################################## +# Flash Memory Information +############################## + +LEOX_elpt860: flinfo + +Bank # 1: AMD AM29F040 (4 Mbits) + Size: 512 KB in 8 Sectors + Sector Start Addresses: + 02000000 (RO) 02010000 (RO) 02020000 (RO) 02030000 (RO) 02040000 + 02050000 02060000 02070000 + +################################################## +# Board Information Structure +############################## + +LEOX_elpt860: bdinfo +memstart = 0x00000000 +memsize = 0x01000000 +flashstart = 0x02000000 +flashsize = 0x00080000 +flashoffset = 0x00030000 +sramstart = 0x00000000 +sramsize = 0x00000000 +immr_base = 0xFF000000 +bootflags = 0x00000001 +intfreq = 50 MHz +busfreq = 50 MHz +ethaddr = 00:03:ca:00:64:df +IP addr = 192.168.0.30 +baudrate = 9600 bps + +################################################## +# Image Download and run over serial port +# hello_world (S-Record image) +# ===> 1) Enter "loads" command into U-Boot monitor +# ===> 2) From TeraTerm's bar menu, Select 'File/Send file...' +# Then select 'hello_world.srec' with the file browser +############################## + +U-Boot 0.2.2 (Jan 19 2003 - 11:08:39) + +CPU: XPC860xxZPnnB at 50 MHz: 4 kB I-Cache 4 kB D-Cache FEC present + *** Warning: CPU Core has Silicon Bugs -- Check the Errata *** +Board: ### No HW ID - assuming ELPT860 +DRAM: 16 MB +FLASH: 512 kB +In: serial +Out: serial +Err: serial +Net: SCC ETHERNET + +Type "run nfsboot" to mount root filesystem over NFS + +Hit any key to stop autoboot: 0 +LEOX_elpt860: loads +## Ready for S-Record download ... +S804040004F3050154000501709905014C000501388D +## First Load Addr = 0x00040000 +## Last Load Addr = 0x0005018B +## Total Size = 0x0001018C = 65932 Bytes +## Start Addr = 0x00040004 +LEOX_elpt860: go 40004 This is a test !!! +## Starting application at 0x00040004 ... +Hello World +argc = 6 +argv[0] = "40004" +argv[1] = "This" +argv[2] = "is" +argv[3] = "a" +argv[4] = "test" +argv[5] = "!!!" +argv[6] = "" +Hit any key to exit ... + +## Application terminated, rc = 0x0 + +################################################## +# Image download and run over ethernet interface +# Linux-2.4.4 (uImage) + Root filesystem mounted over NFS +############################## + +U-Boot 0.2.2 (Jan 19 2003 - 11:08:39) + +CPU: XPC860xxZPnnB at 50 MHz: 4 kB I-Cache 4 kB D-Cache FEC present + *** Warning: CPU Core has Silicon Bugs -- Check the Errata *** +Board: ### No HW ID - assuming ELPT860 +DRAM: 16 MB +FLASH: 512 kB +In: serial +Out: serial +Err: serial +Net: SCC ETHERNET + +Type "run nfsboot" to mount root filesystem over NFS + +Hit any key to stop autoboot: 0 +LEOX_elpt860: run nfsboot +ARP broadcast 1 +TFTP from server 192.168.0.1; our IP address is 192.168.0.30 +Filename '/home/leox/uImage'. +Load address: 0x400000 +Loading: ################################################################# + ############################# +done +Bytes transferred = 477294 (7486e hex) +## Booting image at 00400000 ... + Image Name: Linux-2.4.4 + Image Type: PowerPC Linux Kernel Image (gzip compressed) + Data Size: 477230 Bytes = 466 kB = 0 MB + Load Address: 00000000 + Entry Point: 00000000 + Verifying Checksum ... OK + Uncompressing Kernel Image ... OK +Linux version 2.4.4-rthal5 (leox@p5ak6650) (gcc version 2.95.3 20010315 (release/MontaVista)) #1 Wed Jul 3 10:23:53 CEST 2002 +On node 0 totalpages: 4096 +zone(0): 4096 pages. +zone(1): 0 pages. +zone(2): 0 pages. +Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.1:/tftp/192.168.0.30 ip=192.168.0.30:192.168.0.1:192.168.0.1:255.255.255.0::eth0: +rtsched version <20010618.1050.24> +Decrementer Frequency: 3125000 +Warning: real time clock seems stuck! +Calibrating delay loop... 49.76 BogoMIPS +Memory: 14720k available (928k kernel code, 384k data, 44k init, 0k highmem) +Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes) +Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) +Page-cache hash table entries: 4096 (order: 2, 16384 bytes) +Inode-cache hash table entries: 1024 (order: 1, 8192 bytes) +POSIX conformance testing by UNIFIX +Linux NET4.0 for Linux 2.4 +Based upon Swansea University Computer Society NET3.039 +Starting kswapd v1.8 +CPM UART driver version 0.03 +ttyS0 on SMC1 at 0x0280, BRG1 +block: queued sectors max/low 9701kB/3233kB, 64 slots per queue +RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize +eth0: CPM ENET Version 0.2 on SCC1, 00:03:ca:00:64:df +NET4: Linux TCP/IP 1.0 for NET4.0 +IP Protocols: ICMP, UDP, TCP +IP: routing cache hash table of 512 buckets, 4Kbytes +TCP: Hash tables configured (established 1024 bind 1024) +NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. +Looking up port of RPC 100003/2 on 192.168.0.1 +Looking up port of RPC 100005/2 on 192.168.0.1 +VFS: Mounted root (nfs filesystem). +Freeing unused kernel memory: 44k init +INIT: version 2.78 booting + Welcome to DENX Embedded Linux Environment + Press 'I' to enter interactive startup. +Mounting proc filesystem: [ OK ] +Configuring kernel parameters: [ OK ] +Cannot access the Hardware Clock via any known method. +Use the --debug option to see the details of our search for an access method. +Setting clock : Wed Dec 31 19:00:11 EST 1969 [ OK ] +Activating swap partitions: [ OK ] +Setting hostname 192.168.0.30: [ OK ] +Finding module dependencies: +[ OK ] +Checking filesystems +Checking all file systems. +[ OK ] +Mounting local filesystems: [ OK ] +Enabling swap space: [ OK ] +INIT: Entering runlevel: 3 +Entering non-interactive startup +Starting system logger: [ OK ] +Starting kernel logger: [ OK ] +Starting xinetd: [ OK ] + +192 login: root +Last login: Wed Dec 31 19:00:41 on ttyS0 +bash-2.04# + +################################################## +# Image download and run over ethernet interface +# Linux-2.4.4 + Root filesystem mounted from RAM (pMulti) +############################## + +U-Boot 0.2.2 (Jan 19 2003 - 11:08:39) + +CPU: XPC860xxZPnnB at 50 MHz: 4 kB I-Cache 4 kB D-Cache FEC present + *** Warning: CPU Core has Silicon Bugs -- Check the Errata *** +Board: ### No HW ID - assuming ELPT860 +DRAM: 16 MB +FLASH: 512 kB +In: serial +Out: serial +Err: serial +Net: SCC ETHERNET + +Type "run nfsboot" to mount root filesystem over NFS + +Hit any key to stop autoboot: 0 +LEOX_elpt860: run ramboot +ARP broadcast 1 +TFTP from server 192.168.0.1; our IP address is 192.168.0.30 +Filename '/home/leox/pMulti'. +Load address: 0x400000 +Loading: ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ######################################################## +done +Bytes transferred = 1947816 (1db8a8 hex) +## Booting image at 00400000 ... + Image Name: linux-2.4.4-2002-03-21 Multiboot + Image Type: PowerPC Linux Multi-File Image (gzip compressed) + Data Size: 1947752 Bytes = 1902 kB = 1 MB + Load Address: 00000000 + Entry Point: 00000000 + Contents: + Image 0: 477230 Bytes = 466 kB = 0 MB + Image 1: 1470508 Bytes = 1436 kB = 1 MB + Verifying Checksum ... OK + Uncompressing Multi-File Image ... OK + Loading Ramdisk to 00e44000, end 00fab02c ... OK +Linux version 2.4.4-rthal5 (leox@p5ak6650) (gcc version 2.95.3 20010315 (release/MontaVista)) #1 Wed Jul 3 10:23:53 CEST 2002 +On node 0 totalpages: 4096 +zone(0): 4096 pages. +zone(1): 0 pages. +zone(2): 0 pages. +Kernel command line: root=/dev/ram rw +rtsched version <20010618.1050.24> +Decrementer Frequency: 3125000 +Warning: real time clock seems stuck! +Calibrating delay loop... 49.76 BogoMIPS +Memory: 13280k available (928k kernel code, 384k data, 44k init, 0k highmem) +Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes) +Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) +Page-cache hash table entries: 4096 (order: 2, 16384 bytes) +Inode-cache hash table entries: 1024 (order: 1, 8192 bytes) +POSIX conformance testing by UNIFIX +Linux NET4.0 for Linux 2.4 +Based upon Swansea University Computer Society NET3.039 +Starting kswapd v1.8 +CPM UART driver version 0.03 +ttyS0 on SMC1 at 0x0280, BRG1 +block: queued sectors max/low 8741kB/2913kB, 64 slots per queue +RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize +eth0: CPM ENET Version 0.2 on SCC1, 00:03:ca:00:64:df +RAMDISK: Compressed image found at block 0 +Freeing initrd memory: 1436k freed +NET4: Linux TCP/IP 1.0 for NET4.0 +IP Protocols: ICMP, UDP, TCP +IP: routing cache hash table of 512 buckets, 4Kbytes +TCP: Hash tables configured (established 1024 bind 1024) +IP-Config: Incomplete network configuration information. +NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. +VFS: Mounted root (ext2 filesystem). +Freeing unused kernel memory: 44k iné +init started: BusyBox v0.60.2 (2002.07.01-12:06+0000) multi-call Configuring hostname +Configuring lo... +Configuring eth0... +Configuring Gateway... + +Please press Enter to activate this console. + +ELPT860 login: root +Password: +Welcome to Linux-2.4.4 for ELPT CPU board (MPC860T @ 50MHz) + + a8888b. + d888888b. + 8P"YP"Y88 + _ _ 8|o||o|88 + | | |_| 8' .88 + | | _ ____ _ _ _ _ 8`._.' Y8. + | | | | _ \| | | |\ \/ / d/ `8b. + | |___ | | | | | |_| |/ \ .dP . Y8b. + |_____||_|_| |_|\____|\_/\_/ d8:' " `::88b. + d8" `Y88b + :8P ' :888 + 8a. : _a88P + ._/"Yaa_ : .| 88P| + \ YP" `| 8P `. + / \._____.d| .' + `--..__)888888P`._.' +login[21]: root login on `ttyS0' + + + +BusyBox v0.60.3 (2002.07.20-10:39+0000) Built-in shell (ash) +Enter 'help' for a list of built-in commands. + +root@ELPT860:~ # diff --git a/board/LEOX/elpt860/config.mk b/board/LEOX/elpt860/config.mk new file mode 100644 index 000000000..defc36080 --- /dev/null +++ b/board/LEOX/elpt860/config.mk @@ -0,0 +1,36 @@ +####################################################################### +# +# Copyright (C) 2000, 2001, 2002, 2003 +# The LEOX team , http://www.leox.org +# +# LEOX.org is about the development of free hardware and software resources +# for system on chip. +# +# Description: U-Boot port on the LEOX's ELPT860 CPU board +# ~~~~~~~~~~~ +# +####################################################################### +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +####################################################################### + +# +# ELPT860 board +# + +TEXT_BASE = 0x02000000 +#TEXT_BASE = 0x00FB0000 diff --git a/board/LEOX/elpt860/elpt860.c b/board/LEOX/elpt860/elpt860.c new file mode 100644 index 000000000..25645462f --- /dev/null +++ b/board/LEOX/elpt860/elpt860.c @@ -0,0 +1,399 @@ +/* +**===================================================================== +** +** Copyright (C) 2000, 2001, 2002, 2003 +** The LEOX team , http://www.leox.org +** +** LEOX.org is about the development of free hardware and software resources +** for system on chip. +** +** Description: U-Boot port on the LEOX's ELPT860 CPU board +** ~~~~~~~~~~~ +** +**===================================================================== +** +** This program is free software; you can redistribute it and/or +** modify it under the terms of the GNU General Public License as +** published by the Free Software Foundation; either version 2 of +** the License, or (at your option) any later version. +** +** This program is distributed in the hope that it will be useful, +** but WITHOUT ANY WARRANTY; without even the implied warranty of +** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +** GNU General Public License for more details. +** +** You should have received a copy of the GNU General Public License +** along with this program; if not, write to the Free Software +** Foundation, Inc., 59 Temple Place, Suite 330, Boston, +** MA 02111-1307 USA +** +**===================================================================== +*/ + +/* +** Note 1: In this file, you have to provide the following functions: +** ------ +** int board_pre_init(void) +** int checkboard(void) +** long int initdram(int board_type) +** called from 'board_init_f()' into 'common/board.c' +** +** void reset_phy(void) +** called from 'board_init_r()' into 'common/board.c' +*/ + +#include +#include + +/* ------------------------------------------------------------------------- */ + +static long int dram_size (long int, long int *, long int); + +/* ------------------------------------------------------------------------- */ + +#define _NOT_USED_ 0xFFFFFFFF + +const uint init_sdram_table[] = +{ + /* + * Single Read. (Offset 0 in UPMA RAM) + */ + 0x0FFCCC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, + 0xFFFFFC04, /* last */ + /* + * SDRAM Initialization (offset 5 in UPMA RAM) + * + * This is no UPM entry point. The following definition uses + * the remaining space to establish an initialization + * sequence, which is executed by a RUN command. + * + */ + 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, /* last */ + /* + * Burst Read. (Offset 8 in UPMA RAM) + */ + 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, /* last */ + /* + * Single Write. (Offset 18 in UPMA RAM) + */ + 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, + 0xFFFFFC04, 0xFFFFFC04, 0x0FFFFC04, 0xFFFFFC04, /* last */ + /* + * Burst Write. (Offset 20 in UPMA RAM) + */ + 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC34, 0x0FAC0C34, + 0xFFFFFC05, 0xFFFFFC04, 0x0FFCFC04, 0xFFFFFC05, /* last */ +}; + +const uint sdram_table[] = +{ + /* + * Single Read. (Offset 0 in UPMA RAM) + */ + 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04, + 0xFF0FFC00, /* last */ + /* + * SDRAM Initialization (offset 5 in UPMA RAM) + * + * This is no UPM entry point. The following definition uses + * the remaining space to establish an initialization + * sequence, which is executed by a RUN command. + * + */ + 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC05, /* last */ + /* + * Burst Read. (Offset 8 in UPMA RAM) + */ + 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04, + 0xF00FFC00, 0xF00FFC00, 0xF00FFC00, 0xFF0FFC00, + 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04, + 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */ + /* + * Single Write. (Offset 18 in UPMA RAM) + */ + 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF0C00, + 0xFF0FFC04, 0x0FFCCC04, 0xFFAFFC05, /* last */ + _NOT_USED_, + /* + * Burst Write. (Offset 20 in UPMA RAM) + */ + 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC00, 0x00AF0C00, + 0xF00FFC00, 0xF00FFC00, 0xF00FFC04, 0x0FFCCC04, + 0xFFAFFC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04, + 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */ + /* + * Refresh (Offset 30 in UPMA RAM) + */ + 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC05, 0xFFFFFC04, 0xFFFFFC05, _NOT_USED_, + 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */ + /* + * Exception. (Offset 3c in UPMA RAM) + */ + 0x0FFFFC34, 0x0FAC0C34, 0xFFFFFC05, 0xFFAFFC04, /* last */ +}; + +/* ------------------------------------------------------------------------- */ + +#define CFG_PC4 0x0800 + +#define CFG_DS1 CFG_PC4 + +/* + * Very early board init code (fpga boot, etc.) + */ +int +board_pre_init (void) +{ + volatile immap_t *immr = (immap_t *) CFG_IMMR; + + /* + * Light up the red led on ELPT860 pcb (DS1) (PCDAT) + */ + immr->im_ioport.iop_pcdat &= ~CFG_DS1; /* PCDAT (DS1 = 0) */ + immr->im_ioport.iop_pcpar &= ~CFG_DS1; /* PCPAR (0=general purpose I/O) */ + immr->im_ioport.iop_pcdir |= CFG_DS1; /* PCDIR (I/O: 0=input, 1=output) */ + + return ( 0 ); /* success */ +} + +/* + * Check Board Identity: + * + * Test ELPT860 ID string + * + * Return 1 if no second DRAM bank, otherwise returns 0 + */ + +int +checkboard (void) +{ + unsigned char *s = getenv("serial#"); + + if ( !s || strncmp(s, "ELPT860", 7) ) + printf ("### No HW ID - assuming ELPT860\n"); + + return ( 0 ); /* success */ +} + +/* ------------------------------------------------------------------------- */ + +long int +initdram (int board_type) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile memctl8xx_t *memctl = &immap->im_memctl; + long int size8, size9; + long int size_b0 = 0; + + /* + * This sequence initializes SDRAM chips on ELPT860 board + */ + upmconfig(UPMA, (uint *)init_sdram_table, + sizeof(init_sdram_table)/sizeof(uint)); + + memctl->memc_mptpr = 0x0200; + memctl->memc_mamr = 0x18002111; + + memctl->memc_mar = 0x00000088; + memctl->memc_mcr = 0x80002000; /* CS1: SDRAM bank 0 */ + + upmconfig(UPMA, (uint *)sdram_table, + sizeof(sdram_table)/sizeof(uint)); + + /* + * Preliminary prescaler for refresh (depends on number of + * banks): This value is selected for four cycles every 62.4 us + * with two SDRAM banks or four cycles every 31.2 us with one + * bank. It will be adjusted after memory sizing. + */ + memctl->memc_mptpr = CFG_MPTPR_2BK_8K; + + /* + * The following value is used as an address (i.e. opcode) for + * the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If + * the port size is 32bit the SDRAM does NOT "see" the lower two + * address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for + * MICRON SDRAMs: + * -> 0 00 010 0 010 + * | | | | +- Burst Length = 4 + * | | | +----- Burst Type = Sequential + * | | +------- CAS Latency = 2 + * | +----------- Operating Mode = Standard + * +-------------- Write Burst Mode = Programmed Burst Length + */ + memctl->memc_mar = 0x00000088; + + /* + * Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at + * preliminary addresses - these have to be modified after the + * SDRAM size has been determined. + */ + memctl->memc_or1 = CFG_OR1_PRELIM; + memctl->memc_br1 = CFG_BR1_PRELIM; + + memctl->memc_mamr = CFG_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */ + + udelay (200); + + /* perform SDRAM initializsation sequence */ + + memctl->memc_mcr = 0x80002105; /* CS1: SDRAM bank 0 */ + udelay (1); + memctl->memc_mcr = 0x80002230; /* CS1: SDRAM bank 0 - execute twice */ + udelay (1); + + memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */ + + udelay (1000); + + /* + * Check Bank 0 Memory Size for re-configuration + * + * try 8 column mode + */ + size8 = dram_size (CFG_MAMR_8COL, + (ulong *) SDRAM_BASE1_PRELIM, + SDRAM_MAX_SIZE); + + udelay (1000); + + /* + * try 9 column mode + */ + size9 = dram_size (CFG_MAMR_9COL, + (ulong *) SDRAM_BASE1_PRELIM, + SDRAM_MAX_SIZE); + + if ( size8 < size9 ) /* leave configuration at 9 columns */ + { + size_b0 = size9; + /* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */ + } + else /* back to 8 columns */ + { + size_b0 = size8; + memctl->memc_mamr = CFG_MAMR_8COL; + udelay (500); + /* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */ + } + + udelay (1000); + + /* + * Adjust refresh rate depending on SDRAM type, both banks + * For types > 128 MBit leave it at the current (fast) rate + */ + if ( size_b0 < 0x02000000 ) + { + /* reduce to 15.6 us (62.4 us / quad) */ + memctl->memc_mptpr = CFG_MPTPR_2BK_4K; + udelay (1000); + } + + /* + * Final mapping: map bigger bank first + */ + memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM; + memctl->memc_br1 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V; + + { + unsigned long reg; + + /* adjust refresh rate depending on SDRAM type, one bank */ + reg = memctl->memc_mptpr; + reg >>= 1; /* reduce to CFG_MPTPR_1BK_8K / _4K */ + memctl->memc_mptpr = reg; + } + + udelay(10000); + + return (size_b0); +} + +/* ------------------------------------------------------------------------- */ + +/* + * Check memory range for valid RAM. A simple memory test determines + * the actually available RAM size between addresses `base' and + * `base + maxsize'. Some (not all) hardware errors are detected: + * - short between address lines + * - short between data lines + */ + +static long int +dram_size (long int mamr_value, + long int *base, + long int maxsize) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile memctl8xx_t *memctl = &immap->im_memctl; + volatile long int *addr; + ulong cnt, val; + ulong save[32]; /* to make test non-destructive */ + unsigned char i = 0; + + memctl->memc_mamr = mamr_value; + + for (cnt = maxsize/sizeof(long); cnt > 0; cnt >>= 1) + { + addr = base + cnt; /* pointer arith! */ + + save[i++] = *addr; + *addr = ~cnt; + } + + /* write 0 to base address */ + addr = base; + save[i] = *addr; + *addr = 0; + + /* check at base address */ + if ( (val = *addr) != 0 ) + { + *addr = save[i]; + + return (0); + } + + for (cnt = 1; cnt <= maxsize/sizeof(long); cnt <<= 1) + { + addr = base + cnt; /* pointer arith! */ + + val = *addr; + *addr = save[--i]; + + if ( val != (~cnt) ) + { + return (cnt * sizeof(long)); + } + } + + return (maxsize); +} + +/* ------------------------------------------------------------------------- */ + +#define CFG_PA1 0x4000 +#define CFG_PA2 0x2000 + +#define CFG_LBKs (CFG_PA2 | CFG_PA1) + +void +reset_phy (void) +{ + volatile immap_t *immr = (immap_t *) CFG_IMMR; + + /* + * Ensure LBK LXT901 ethernet 1 & 2 = 0 ... for normal loopback in effect + * and no AUI loopback + */ + immr->im_ioport.iop_padat &= ~CFG_LBKs; /* PADAT (LBK eth 1&2 = 0) */ + immr->im_ioport.iop_papar &= ~CFG_LBKs; /* PAPAR (0=general purpose I/O) */ + immr->im_ioport.iop_padir |= CFG_LBKs; /* PADIR (I/O: 0=input, 1=output) */ +} diff --git a/board/LEOX/elpt860/flash.c b/board/LEOX/elpt860/flash.c new file mode 100644 index 000000000..a9238e16c --- /dev/null +++ b/board/LEOX/elpt860/flash.c @@ -0,0 +1,615 @@ +/* +**===================================================================== +** +** Copyright (C) 2000, 2001, 2002, 2003 +** The LEOX team , http://www.leox.org +** +** LEOX.org is about the development of free hardware and software resources +** for system on chip. +** +** Description: U-Boot port on the LEOX's ELPT860 CPU board +** ~~~~~~~~~~~ +** +**===================================================================== +** +** This program is free software; you can redistribute it and/or +** modify it under the terms of the GNU General Public License as +** published by the Free Software Foundation; either version 2 of +** the License, or (at your option) any later version. +** +** This program is distributed in the hope that it will be useful, +** but WITHOUT ANY WARRANTY; without even the implied warranty of +** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +** GNU General Public License for more details. +** +** You should have received a copy of the GNU General Public License +** along with this program; if not, write to the Free Software +** Foundation, Inc., 59 Temple Place, Suite 330, Boston, +** MA 02111-1307 USA +** +**===================================================================== +*/ + +/* +** Note 1: In this file, you have to provide the following variable: +** ------ +** flash_info_t flash_info[CFG_MAX_FLASH_BANKS] +** 'flash_info_t' structure is defined into 'include/flash.h' +** and defined as extern into 'common/cmd_flash.c' +** +** Note 2: In this file, you have to provide the following functions: +** ------ +** unsigned long flash_init(void) +** called from 'board_init_r()' into 'common/board.c' +** +** void flash_print_info(flash_info_t *info) +** called from 'do_flinfo()' into 'common/cmd_flash.c' +** +** int flash_erase(flash_info_t *info, +** int s_first, +** int s_last) +** called from 'do_flerase()' & 'flash_sect_erase()' into 'common/cmd_flash.c' +** +** int write_buff (flash_info_t *info, +** uchar *src, +** ulong addr, +** ulong cnt) +** called from 'flash_write()' into 'common/cmd_flash.c' +*/ + +#include +#include + + +#ifndef CFG_ENV_ADDR +# define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_ENV_OFFSET) +#endif + +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +/*----------------------------------------------------------------------- + * Internal Functions + */ +static void flash_get_offsets (ulong base, flash_info_t *info); +static ulong flash_get_size (volatile unsigned char *addr, flash_info_t *info); + +static int write_word (flash_info_t *info, ulong dest, ulong data); +static int write_byte (flash_info_t *info, ulong dest, uchar data); + +/*----------------------------------------------------------------------- + */ + +unsigned long +flash_init (void) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile memctl8xx_t *memctl = &immap->im_memctl; + unsigned long size_b0; + int i; + + /* Init: no FLASHes known */ + for (i=0; imemc_or0 = CFG_OR_TIMING_FLASH | (-size_b0 & OR_AM_MSK); + memctl->memc_br0 = (CFG_FLASH_BASE & BR_BA_MSK) | BR_MS_GPCM | BR_PS_8 | BR_V; + + /* Re-do sizing to get full correct info */ + size_b0 = flash_get_size ((volatile unsigned char *)CFG_FLASH_BASE, + &flash_info[0]); + + flash_get_offsets (CFG_FLASH_BASE, &flash_info[0]); + +#if CFG_MONITOR_BASE >= CFG_FLASH_BASE + /* monitor protection ON by default */ + flash_protect (FLAG_PROTECT_SET, + CFG_MONITOR_BASE, + CFG_MONITOR_BASE + CFG_MONITOR_LEN-1, + &flash_info[0]); +#endif + +#ifdef CFG_ENV_IS_IN_FLASH + /* ENV protection ON by default */ + flash_protect(FLAG_PROTECT_SET, + CFG_ENV_ADDR, + CFG_ENV_ADDR + CFG_ENV_SIZE-1, + &flash_info[0]); +#endif + + flash_info[0].size = size_b0; + + return (size_b0); +} + +/*----------------------------------------------------------------------- + */ +static void +flash_get_offsets (ulong base, + flash_info_t *info) +{ + int i; + +#define SECTOR_64KB 0x00010000 + + /* set up sector start adress table */ + for (i = 0; i < info->sector_count; i++) + { + info->start[i] = base + (i * SECTOR_64KB); + } +} + +/*----------------------------------------------------------------------- + */ +void +flash_print_info (flash_info_t *info) +{ + int i; + + if ( info->flash_id == FLASH_UNKNOWN ) + { + printf ("missing or unknown FLASH type\n"); + return; + } + + switch ( info->flash_id & FLASH_VENDMASK ) + { + case FLASH_MAN_AMD: printf ("AMD "); break; + case FLASH_MAN_FUJ: printf ("FUJITSU "); break; + case FLASH_MAN_STM: printf ("STM (Thomson) "); break; + default: printf ("Unknown Vendor "); break; + } + + switch ( info->flash_id & FLASH_TYPEMASK ) + { + case FLASH_AM040: printf ("AM29F040 (4 Mbits)\n"); + break; + default: printf ("Unknown Chip Type\n"); + break; + } + + printf (" Size: %ld KB in %d Sectors\n", + info->size >> 10, info->sector_count); + + printf (" Sector Start Addresses:"); + for (i=0; isector_count; ++i) + { + if ((i % 5) == 0) + printf ("\n "); + printf (" %08lX%s", + info->start[i], + info->protect[i] ? " (RO)" : " " + ); + } + printf ("\n"); + + return; +} + +/*----------------------------------------------------------------------- + */ + + +/*----------------------------------------------------------------------- + */ + +/* + * The following code cannot be run from FLASH! + */ + +static ulong +flash_get_size (volatile unsigned char *addr, + flash_info_t *info) +{ + short i; + uchar value; + ulong base = (ulong)addr; + + /* Write auto select command: read Manufacturer ID */ + addr[0x0555] = 0xAA; + addr[0x02AA] = 0x55; + addr[0x0555] = 0x90; + + value = addr[0]; + + switch ( value ) + { + /* case AMD_MANUFACT: */ + case 0x01: + info->flash_id = FLASH_MAN_AMD; + break; + /* case FUJ_MANUFACT: */ + case 0x04: + info->flash_id = FLASH_MAN_FUJ; + break; + /* case STM_MANUFACT: */ + case 0x20: + info->flash_id = FLASH_MAN_STM; + break; + + default: + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + return (0); /* no or unknown flash */ + } + + value = addr[1]; /* device ID */ + + switch ( value ) + { + case STM_ID_F040B: + case AMD_ID_F040B: + info->flash_id += FLASH_AM040; /* 4 Mbits = 512k * 8 */ + info->sector_count = 8; + info->size = 0x00080000; + break; + + default: + info->flash_id = FLASH_UNKNOWN; + return (0); /* => no or unknown flash */ + } + + /* set up sector start adress table */ + for (i = 0; i < info->sector_count; i++) + { + info->start[i] = base + (i * 0x00010000); + } + + /* check for protected sectors */ + for (i = 0; i < info->sector_count; i++) + { + /* read sector protection at sector address, (A7 .. A0) = 0x02 */ + /* D0 = 1 if protected */ + addr = (volatile unsigned char *)(info->start[i]); + info->protect[i] = addr[2] & 1; + } + + /* + * Prevent writes to uninitialized FLASH. + */ + if ( info->flash_id != FLASH_UNKNOWN ) + { + addr = (volatile unsigned char *)info->start[0]; + + *addr = 0xF0; /* reset bank */ + } + + return (info->size); +} + + +/*----------------------------------------------------------------------- + */ + +int +flash_erase (flash_info_t *info, + int s_first, + int s_last) +{ + volatile unsigned char *addr = (volatile unsigned char *)(info->start[0]); + int flag, prot, sect, l_sect; + ulong start, now, last; + + if ( (s_first < 0) || (s_first > s_last) ) + { + if ( info->flash_id == FLASH_UNKNOWN ) + { + printf ("- missing\n"); + } + else + { + printf ("- no sectors to erase\n"); + } + return ( 1 ); + } + + if ( (info->flash_id == FLASH_UNKNOWN) || + (info->flash_id > FLASH_AMD_COMP) ) + { + printf ("Can't erase unknown flash type %08lx - aborted\n", + info->flash_id); + return ( 1 ); + } + + prot = 0; + for (sect=s_first; sect<=s_last; ++sect) + { + if ( info->protect[sect] ) + { + prot++; + } + } + + if ( prot ) + { + printf ("- Warning: %d protected sectors will not be erased!\n", prot); + } + else + { + printf ("\n"); + } + + l_sect = -1; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + addr[0x0555] = 0xAA; + addr[0x02AA] = 0x55; + addr[0x0555] = 0x80; + addr[0x0555] = 0xAA; + addr[0x02AA] = 0x55; + + /* Start erase on unprotected sectors */ + for (sect = s_first; sect<=s_last; sect++) + { + if (info->protect[sect] == 0) /* not protected */ + { + addr = (volatile unsigned char *)(info->start[sect]); + addr[0] = 0x30; + l_sect = sect; + } + } + + /* re-enable interrupts if necessary */ + if ( flag ) + enable_interrupts(); + + /* wait at least 80us - let's wait 1 ms */ + udelay (1000); + + /* + * We wait for the last triggered sector + */ + if ( l_sect < 0 ) + goto DONE; + + start = get_timer (0); + last = start; + addr = (volatile unsigned char *)(info->start[l_sect]); + while ( (addr[0] & 0x80) != 0x80 ) + { + if ( (now = get_timer(start)) > CFG_FLASH_ERASE_TOUT ) + { + printf ("Timeout\n"); + return ( 1 ); + } + /* show that we're waiting */ + if ( (now - last) > 1000 ) /* every second */ + { + putc ('.'); + last = now; + } + } + +DONE: + /* reset to read mode */ + addr = (volatile unsigned char *)info->start[0]; + addr[0] = 0xF0; /* reset bank */ + + printf (" done\n"); + + return ( 0 ); +} + +/*----------------------------------------------------------------------- + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ + +int +write_buff (flash_info_t *info, + uchar *src, + ulong addr, + ulong cnt) +{ + ulong cp, wp, data; + uchar bdata; + int i, l, rc; + + if ( (info->flash_id & FLASH_TYPEMASK) == FLASH_AM040 ) + { + /* Width of the data bus: 8 bits */ + + wp = addr; + + while ( cnt ) + { + bdata = *src++; + + if ( (rc = write_byte(info, wp, bdata)) != 0 ) + { + return (rc); + } + + ++wp; + --cnt; + } + + return ( 0 ); + } + else + { + /* Width of the data bus: 32 bits */ + + wp = (addr & ~3); /* get lower word aligned address */ + + /* + * handle unaligned start bytes + */ + if ( (l = addr - wp) != 0 ) + { + data = 0; + for (i=0, cp=wp; i0; ++i) + { + data = (data << 8) | *src++; + --cnt; + ++cp; + } + for (; cnt==0 && i<4; ++i, ++cp) + { + data = (data << 8) | (*(uchar *)cp); + } + + if ( (rc = write_word(info, wp, data)) != 0 ) + { + return (rc); + } + wp += 4; + } + + /* + * handle word aligned part + */ + while ( cnt >= 4 ) + { + data = 0; + for (i=0; i<4; ++i) + { + data = (data << 8) | *src++; + } + if ( (rc = write_word(info, wp, data)) != 0 ) + { + return (rc); + } + wp += 4; + cnt -= 4; + } + + if ( cnt == 0 ) + { + return (0); + } + + /* + * handle unaligned tail bytes + */ + data = 0; + for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) + { + data = (data << 8) | *src++; + --cnt; + } + for (; i<4; ++i, ++cp) + { + data = (data << 8) | (*(uchar *)cp); + } + + return (write_word(info, wp, data)); + } +} + +/*----------------------------------------------------------------------- + * Write a word to Flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +static int +write_word (flash_info_t *info, + ulong dest, + ulong data) +{ + vu_long *addr = (vu_long*)(info->start[0]); + ulong start; + int flag; + + /* Check if Flash is (sufficiently) erased */ + if ( (*((vu_long *)dest) & data) != data ) + { + return (2); + } + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + addr[0x0555] = 0x00AA00AA; + addr[0x02AA] = 0x00550055; + addr[0x0555] = 0x00A000A0; + + *((vu_long *)dest) = data; + + /* re-enable interrupts if necessary */ + if ( flag ) + enable_interrupts(); + + /* data polling for D7 */ + start = get_timer (0); + while ( (*((vu_long *)dest) & 0x00800080) != (data & 0x00800080) ) + { + if ( get_timer(start) > CFG_FLASH_WRITE_TOUT ) + { + return (1); + } + } + + return (0); +} + +/*----------------------------------------------------------------------- + * Write a byte to Flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +static int +write_byte (flash_info_t *info, + ulong dest, + uchar data) +{ + volatile unsigned char *addr = (volatile unsigned char *)(info->start[0]); + ulong start; + int flag; + + /* Check if Flash is (sufficiently) erased */ + if ( (*((volatile unsigned char *)dest) & data) != data ) + { + return (2); + } + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + addr[0x0555] = 0xAA; + addr[0x02AA] = 0x55; + addr[0x0555] = 0xA0; + + *((volatile unsigned char *)dest) = data; + + /* re-enable interrupts if necessary */ + if ( flag ) + enable_interrupts(); + + /* data polling for D7 */ + start = get_timer (0); + while ( (*((volatile unsigned char *)dest) & 0x80) != (data & 0x80) ) + { + if ( get_timer(start) > CFG_FLASH_WRITE_TOUT ) + { + return (1); + } + } + + return (0); +} + +/*----------------------------------------------------------------------- + */ diff --git a/board/LEOX/elpt860/u-boot.lds b/board/LEOX/elpt860/u-boot.lds new file mode 100644 index 000000000..77945d0dd --- /dev/null +++ b/board/LEOX/elpt860/u-boot.lds @@ -0,0 +1,146 @@ +/* +**===================================================================== +** +** Copyright (C) 2000, 2001, 2002, 2003 +** The LEOX team , http://www.leox.org +** +** LEOX.org is about the development of free hardware and software resources +** for system on chip. +** +** Description: U-Boot port on the LEOX's ELPT860 CPU board +** ~~~~~~~~~~~ +** +**===================================================================== +** +** This program is free software; you can redistribute it and/or +** modify it under the terms of the GNU General Public License as +** published by the Free Software Foundation; either version 2 of +** the License, or (at your option) any later version. +** +** This program is distributed in the hope that it will be useful, +** but WITHOUT ANY WARRANTY; without even the implied warranty of +** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +** GNU General Public License for more details. +** +** You should have received a copy of the GNU General Public License +** along with this program; if not, write to the Free Software +** Foundation, Inc., 59 Temple Place, Suite 330, Boston, +** MA 02111-1307 USA +** +**===================================================================== +*/ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/mpc8xx/start.o (.text) + common/dlmalloc.o (.text) + lib_ppc/ppcstring.o (.text) + lib_generic/vsprintf.o (.text) + lib_generic/crc32.o (.text) + lib_generic/zlib.o (.text) + lib_generic/string.o (.text) + lib_ppc/cache.o (.text) + lib_ppc/extable.o (.text) + lib_ppc/time.o (.text) + lib_ppc/ticks.o (.text) + + . = env_offset; + common/environment.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/board/LEOX/elpt860/u-boot.lds.debug b/board/LEOX/elpt860/u-boot.lds.debug new file mode 100644 index 000000000..b81235fd4 --- /dev/null +++ b/board/LEOX/elpt860/u-boot.lds.debug @@ -0,0 +1,140 @@ +/* +**===================================================================== +** +** Copyright (C) 2000, 2001, 2002, 2003 +** The LEOX team , http://www.leox.org +** +** LEOX.org is about the development of free hardware and software resources +** for system on chip. +** +** Description: U-Boot port on the LEOX's ELPT860 CPU board +** ~~~~~~~~~~~ +** +**===================================================================== +** +** This program is free software; you can redistribute it and/or +** modify it under the terms of the GNU General Public License as +** published by the Free Software Foundation; either version 2 of +** the License, or (at your option) any later version. +** +** This program is distributed in the hope that it will be useful, +** but WITHOUT ANY WARRANTY; without even the implied warranty of +** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +** GNU General Public License for more details. +** +** You should have received a copy of the GNU General Public License +** along with this program; if not, write to the Free Software +** Foundation, Inc., 59 Temple Place, Suite 330, Boston, +** MA 02111-1307 USA +** +**===================================================================== +*/ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/mpc8xx/start.o (.text) + common/dlmalloc.o (.text) + lib_generic/vsprintf.o (.text) + lib_generic/crc32.o (.text) + + . = env_offset; + common/environment.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x0FFF) & 0xFFFFF000; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(4096); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(4096); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} + -- cgit v1.2.3