From a380279b2abe130c2d3d2c8de36f8ff98bc6b3b0 Mon Sep 17 00:00:00 2001 From: Daniel Gorsulowski Date: Tue, 29 Sep 2009 08:03:12 +0200 Subject: at91: Update MEESC board support This patch implements several updates: -disable CONFIG_ENV_OVERWRITE -add new hardware style variants and set the arch numbers appropriate -pass the serial# and hardware revision to the kernel -removed unused macros from include/configs/meesc.h -fixed multiline comment style Signed-off-by: Daniel Gorsulowski --- board/esd/meesc/meesc.c | 65 +++++++++++++++++++++++++++++++++++++++++++------ 1 file changed, 58 insertions(+), 7 deletions(-) (limited to 'board/esd') diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c index 636d0ed5f..efba60df9 100644 --- a/board/esd/meesc/meesc.c +++ b/board/esd/meesc/meesc.c @@ -126,8 +126,10 @@ static void meesc_ethercat_hw_init(void) AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(9)); at91_sys_write(AT91_SMC1_CYCLE(0), AT91_SMC_NWECYCLE_(10) | AT91_SMC_NRDCYCLE_(5)); - /* Configure behavior at external wait signal, byte-select mode, 16 bit - data bus width, none data float wait states and TDF optimization */ + /* + * Configure behavior at external wait signal, byte-select mode, 16 bit + * data bus width, none data float wait states and TDF optimization + */ at91_sys_write(AT91_SMC1_MODE(0), AT91_SMC_READMODE | AT91_SMC_EXNWMODE_READY | AT91_SMC_BAT_SELECT | AT91_SMC_DBW_16 | AT91_SMC_TDF_(0) | @@ -156,8 +158,32 @@ int board_eth_init(bd_t *bis) int checkboard(void) { char str[32]; - - puts("Board: esd CAN-EtherCAT Gateway"); + u_char hw_type; /* hardware type */ + + /* read the "Type" register of the ET1100 controller */ + hw_type = readb(CONFIG_ET1100_BASE); + + switch (hw_type) { + case 0x11: + case 0x3F: + /* ET1100 present, arch number of MEESC-Board */ + gd->bd->bi_arch_number = MACH_TYPE_MEESC; + puts("Board: CAN-EtherCAT Gateway"); + break; + case 0xFF: + /* no ET1100 present, arch number of EtherCAN/2-Board */ + gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2; + puts("Board: EtherCAN/2 Gateway"); + /* switch on LED1D */ + at91_set_gpio_output(AT91_PIN_PB12, 1); + break; + default: + /* assume, no ET1100 present, arch number of EtherCAN/2-Board */ + gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2; + printf("ERROR! Read invalid hw_type: %02X\n", hw_type); + puts("Board: EtherCAN/2 Gateway"); + break; + } if (getenv_r("serial#", str, sizeof(str)) > 0) { puts(", serial# "); puts(str); @@ -167,6 +193,32 @@ int checkboard(void) return 0; } +#ifdef CONFIG_SERIAL_TAG +void get_board_serial(struct tag_serialnr *serialnr) +{ + char *str; + + char *serial = getenv("serial#"); + if (serial) { + str = strchr(serial, '_'); + if (str && (strlen(str) >= 4)) { + serialnr->high = (*(str + 1) << 8) | *(str + 2); + serialnr->low = simple_strtoul(str + 3, NULL, 16); + } + } else { + serialnr->high = 0; + serialnr->low = 0; + } +} +#endif + +#ifdef CONFIG_REVISION_TAG +u32 get_board_rev(void) +{ + return hw_rev | 0x100; +} +#endif + int board_init(void) { /* Peripheral Clock Enable Register */ @@ -174,8 +226,8 @@ int board_init(void) 1 << AT91SAM9263_ID_PIOB | 1 << AT91SAM9263_ID_PIOCDE); - /* arch number of MEESC-Board */ - gd->bd->bi_arch_number = MACH_TYPE_MEESC; + /* initialize ET1100 Controller */ + meesc_ethercat_hw_init(); /* adress of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; @@ -184,7 +236,6 @@ int board_init(void) #ifdef CONFIG_CMD_NAND meesc_nand_hw_init(); #endif - meesc_ethercat_hw_init(); #ifdef CONFIG_HAS_DATAFLASH at91_spi0_hw_init(1 << 0); #endif -- cgit v1.2.3