From 5d232d0e7ea982d859d028ab482d95eb68460b19 Mon Sep 17 00:00:00 2001 From: wdenk Date: Thu, 22 May 2003 22:52:13 +0000 Subject: * Patch by Dave Ellis, 22 May 2003: Fix problem with only partially cleared .bss segment * Patch by Rune Torgersen, 12 May 2003: get PCI to work on a MPC8266ADS board; incorporate change to cpu/mpc8260/pci.c to enable overrides of PCI memory parameters --- include/configs/MPC8266ADS.h | 190 +++++++++++++++++++++++++++++++++++-------- 1 file changed, 158 insertions(+), 32 deletions(-) (limited to 'include/configs/MPC8266ADS.h') diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h index 5655547a6..e0159a2b6 100644 --- a/include/configs/MPC8266ADS.h +++ b/include/configs/MPC8266ADS.h @@ -39,7 +39,7 @@ */ #define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ -#define CONFIG_MPC8260ADS 1 /* ...on motorola ads board */ +#define CONFIG_MPC8266ADS 1 /* ...on motorola ads board */ #define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ @@ -78,6 +78,23 @@ #define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ #undef CONFIG_ETHER_NONE /* define if ether on something else */ #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_BITBANGMII /* bit-bang MII PHY management */ +/* + * Port pins used for bit-banged MII communictions (if applicable). + */ +#define MDIO_PORT 2 /* Port C */ +#define MDIO_ACTIVE (iop->pdir |= 0x00400000) +#define MDIO_TRISTATE (iop->pdir &= ~0x00400000) +#define MDIO_READ ((iop->pdat & 0x00400000) != 0) + +#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ + else iop->pdat &= ~0x00400000 + +#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ + else iop->pdat &= ~0x00200000 + +#define MIIDELAY udelay(1) #if (CONFIG_ETHER_INDEX == 2) @@ -90,7 +107,7 @@ # define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) # define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) # define CFG_CPMFCR_RAMTYPE 0 -# define CFG_FCC_PSMR 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) #endif /* CONFIG_ETHER_INDEX */ @@ -100,6 +117,12 @@ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_EEPROM_ADDR_LEN 1 +/* PCI */ +#define CONFIG_PCI +#define CONFIG_PCI_PNP +#define CONFIG_PCI_BOOTDELAY 0 +#undef CONFIG_PCI_SCAN_SHOW + /*----------------------------------------------------------------------- * Definitions for Serial Presence Detect EEPROM address * (to get SDRAM settings) @@ -107,7 +130,7 @@ #define SPD_EEPROM_ADDRESS 0x50 -#define CONFIG_8260_CLKIN 66666666 /* in Hz */ +#define CONFIG_8260_CLKIN 66000000 /* in Hz */ #define CONFIG_BAUDRATE 115200 @@ -116,6 +139,7 @@ CFG_CMD_BMP | \ CFG_CMD_BSP | \ CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ CFG_CMD_DOC | \ CFG_CMD_DTT | \ CFG_CMD_EEPROM | \ @@ -127,21 +151,51 @@ CFG_CMD_JFFS2 | \ CFG_CMD_KGDB | \ CFG_CMD_NAND | \ - CFG_CMD_MII | \ - CFG_CMD_PCI | \ CFG_CMD_PCMCIA | \ CFG_CMD_SCSI | \ CFG_CMD_SPI | \ CFG_CMD_VFD | \ CFG_CMD_USB ) ) +/* Define a command string that is automatically executed when no character + * is read on the console interface withing "Boot Delay" after reset. + */ +#define CONFIG_BOOT_ROOT_INITRD 0 /* Use ram disk for the root file system */ +#define CONFIG_BOOT_ROOT_NFS 1 /* Use a NFS mounted root file system */ + +#if CONFIG_BOOT_ROOT_INITRD +#define CONFIG_BOOTCOMMAND \ + "version;" \ + "echo;" \ + "bootp;" \ + "setenv bootargs root=/dev/ram0 rw " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ + "bootm" +#endif /* CONFIG_BOOT_ROOT_INITRD */ + +#if CONFIG_BOOT_ROOT_NFS +#define CONFIG_BOOTCOMMAND \ + "version;" \ + "echo;" \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ + "bootm" +#endif /* CONFIG_BOOT_ROOT_NFS */ + +/* Add support for a few extra bootp options like: + * - File size + * - DNS + */ +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ + CONFIG_BOOTP_BOOTFILESIZE | \ + CONFIG_BOOTP_DNS) + /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_BOOTCOMMAND "bootm 100000" /* autoboot command */ -#define CONFIG_BOOTARGS "root=/dev/ram rw" #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ @@ -170,7 +224,7 @@ #define CFG_MEMTEST_START 0x00100000 /* memtest works on */ #define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ +#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */ /* for versions < 2.4.5-pre5 */ #define CFG_LOAD_ADDR 0x100000 /* default load address */ @@ -179,8 +233,8 @@ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } -#define CFG_FLASH_BASE 0xff800000 -#define FLASH_BASE 0xff800000 +#define CFG_FLASH_BASE 0xFE000000 +#define FLASH_BASE 0xFE000000 #define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ #define CFG_MAX_FLASH_SECT 32 /* max num of sects on one chip */ #define CFG_FLASH_SIZE 8 @@ -193,14 +247,10 @@ /* Only change this if you also change the Hardware configuration Word */ #define CFG_DEFAULT_IMMR 0x0F010000 -/* -#define CFG_IMMR 0x04700000 -#define CFG_BCSR 0x04500000 -*/ - /* Set IMMR to 0xF0000000 or above to boot Linux */ #define CFG_IMMR 0xF0000000 -#define CFG_BCSR 0x04500000 +#define CFG_BCSR 0xF8000000 +#define CFG_PCI_INT 0xF8200000 /* PCI interrupt controller */ /* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes */ @@ -263,7 +313,7 @@ ORxS_ROWST_PBI0_A8 |\ ORxS_NUMR_12) #elif (CFG_SDRAM_SIZE == 16) -#define CFG_OR2_PRELIM (0xFF000CA0) +#define CFG_OR2_PRELIM (0xFF000C80) #else #error "INVALID SDRAM CONFIGURATION" #endif @@ -325,13 +375,13 @@ #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -/* 0x0EA28205 */ -/*#define CFG_HRCW_MASTER ( ( HRCW_BPS11 | HRCW_CIP ) |\ - ( HRCW_L2CPC10 | HRCW_DPPC10 | HRCW_ISB010 ) |\ - ( HRCW_BMS | HRCW_APPC10 ) |\ - ( HRCW_MODCK_H0101 ) \ +/* 0x0EB2B645 */ +#define CFG_HRCW_MASTER (( HRCW_BPS11 | HRCW_CIP ) |\ + ( HRCW_L2CPC10 | HRCW_DPPC11 | HRCW_ISB010 ) |\ + ( HRCW_BMS | HRCW_MMR11 | HRCW_LBPC01 | HRCW_APPC10 ) |\ + ( HRCW_CS10PC01 | HRCW_MODCK_H0101 ) \ ) -*/ + /* This value should actually be situated in the first 256 bytes of the FLASH which on the standard MPC8266ADS board is at address 0xFF800000 @@ -346,7 +396,7 @@ - Rune */ -#define CFG_HRCW_MASTER 0x0cb23645 +/* #define CFG_HRCW_MASTER 0x0cb23645 */ /* no slaves */ #define CFG_HRCW_SLAVE1 0 @@ -392,22 +442,98 @@ #define CFG_HID2 0 #define CFG_SYPCR 0xFFFFFFC3 -#define CFG_BCR 0x100C0000 -#define CFG_SIUMCR 0x0A200000 +#define CFG_BCR 0x004C0000 +#define CFG_SIUMCR 0x4E64C000 #define CFG_SCCR 0x00000000 -#define CFG_BR0_PRELIM 0xFF801801 -#define CFG_OR0_PRELIM 0xFF800836 -#define CFG_BR1_PRELIM 0x04501801 -#define CFG_OR1_PRELIM 0xFFFF8010 -#define CFG_RMR 0 +/* local bus memory map + * + * 0x00000000-0x03FFFFFF 64MB SDRAM + * 0x80000000-0x9FFFFFFF 512MB outbound prefetchable PCI memory window + * 0xA0000000-0xBFFFFFFF 512MB outbound non-prefetchable PCI memory window + * 0xF0000000-0xF001FFFF 128KB MPC8266 internal memory + * 0xF4000000-0xF7FFFFFF 64MB outbound PCI I/O window + * 0xF8000000-0xF8007FFF 32KB BCSR + * 0xF8100000-0xF8107FFF 32KB ATM UNI + * 0xF8200000-0xF8207FFF 32KB PCI interrupt controller + * 0xF8300000-0xF8307FFF 32KB EEPROM + * 0xFE000000-0xFFFFFFFF 32MB flash + */ +#define CFG_BR0_PRELIM 0xFE001801 /* flash */ +#define CFG_OR0_PRELIM 0xFE000836 +#define CFG_BR1_PRELIM (CFG_BCSR | 0x1801) /* BCSR */ +#define CFG_OR1_PRELIM 0xFFFF8010 +#define CFG_BR4_PRELIM 0xF8300801 /* EEPROM */ +#define CFG_OR4_PRELIM 0xFFFF8846 +#define CFG_BR5_PRELIM 0xF8100801 /* PM5350 ATM UNI */ +#define CFG_OR5_PRELIM 0xFFFF8E36 +#define CFG_BR8_PRELIM (CFG_PCI_INT | 0x1801) /* PCI interrupt controller */ +#define CFG_OR8_PRELIM 0xFFFF8010 + +#define CFG_RMR 0x0001 #define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) #define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) #define CFG_RCCR 0 -/*#define CFG_PSDMR 0x016EB452*/ #define CFG_MPTPR 0x00001900 #define CFG_PSRT 0x00000021 #define CFG_RESET_ADDRESS 0x04400000 +/* PCI Memory map (if different from default map */ +#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE /* Local base */ +#define CFG_PCI_SLV_MEM_BUS 0x00000000 /* PCI base */ +#define CFG_PICMR0_MASK_ATTRIB (PICMR_MASK_512MB | PICMR_ENABLE | \ + PICMR_PREFETCH_EN) + +/* + * These are the windows that allow the CPU to access PCI address space. + * All three PCI master windows, which allow the CPU to access PCI + * prefetch, non prefetch, and IO space (see below), must all fit within + * these windows. + */ + +/* PCIBR0 */ +#define CFG_PCI_MSTR0_LOCAL 0x80000000 /* Local base */ +#define CFG_PCIMSK0_MASK PCIMSK_1GB /* Size of window */ +/* PCIBR1 */ +#define CFG_PCI_MSTR1_LOCAL 0xF4000000 /* Local base */ +#define CFG_PCIMSK1_MASK PCIMSK_64MB /* Size of window */ + +/* + * Master window that allows the CPU to access PCI Memory (prefetch). + * This window will be setup with the first set of Outbound ATU registers + * in the bridge. + */ + +#define CFG_PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */ +#define CFG_PCI_MSTR_MEM_BUS 0x80000000 /* PCI base */ +#define CFG_CPU_PCI_MEM_START PCI_MSTR_MEM_LOCAL +#define CFG_PCI_MSTR_MEM_SIZE 0x20000000 /* 512MB */ +#define CFG_POCMR0_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN) + +/* + * Master window that allows the CPU to access PCI Memory (non-prefetch). + * This window will be setup with the second set of Outbound ATU registers + * in the bridge. + */ + +#define CFG_PCI_MSTR_MEMIO_LOCAL 0xA0000000 /* Local base */ +#define CFG_PCI_MSTR_MEMIO_BUS 0xA0000000 /* PCI base */ +#define CPU_PCI_MEMIO_START PCI_MSTR_MEMIO_LOCAL +#define CFG_PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */ +#define CFG_POCMR1_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE) + +/* + * Master window that allows the CPU to access PCI IO space. + * This window will be setup with the third set of Outbound ATU registers + * in the bridge. + */ + +#define CFG_PCI_MSTR_IO_LOCAL 0xF4000000 /* Local base */ +#define CFG_PCI_MSTR_IO_BUS 0x00000000 /* PCI base */ +#define CFG_CPU_PCI_IO_START PCI_MSTR_IO_LOCAL +#define CFG_PCI_MSTR_IO_SIZE 0x04000000 /* 64MB */ +#define CFG_POCMR2_MASK_ATTRIB (POCMR_MASK_64MB | POCMR_ENABLE | POCMR_PCI_IO) + + #endif /* __CONFIG_H */ -- cgit v1.2.3