From 5b1d713721c3ea02549940133f09236783dda1f9 Mon Sep 17 00:00:00 2001 From: wdenk Date: Sun, 3 Nov 2002 00:07:02 +0000 Subject: Initial revision --- include/configs/RPXsuper.h | 505 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 505 insertions(+) create mode 100644 include/configs/RPXsuper.h (limited to 'include/configs/RPXsuper.h') diff --git a/include/configs/RPXsuper.h b/include/configs/RPXsuper.h new file mode 100644 index 000000000..c36467263 --- /dev/null +++ b/include/configs/RPXsuper.h @@ -0,0 +1,505 @@ +#ifndef __CONFIG_H +#define __CONFIG_H + + +/***************************************************************************** + * + * These settings must match the way _your_ board is set up + * + *****************************************************************************/ +/* for the AY-Revision which does not use the HRCW */ +#define CFG_DEFAULT_IMMR 0x00010000 + +/* What is the oscillator's (UX2) frequency in Hz? */ +#define CONFIG_8260_CLKIN (66 * 1000 * 1000) + +/* How is switch S2 set? We really only want the MODCK[1-3] bits, so + * only the 3 least significant bits are important. +*/ +#define CFG_SBC_S2 0x04 + +/* What should MODCK_H be? It is dependent on the oscillator + * frequency, MODCK[1-3], and desired CPM and core frequencies. + * Some example values (all frequencies are in MHz): + * + * MODCK_H MODCK[1-3] Osc CPM Core + * 0x2 0x2 33 133 133 + * 0x2 0x4 33 133 200 + * 0x5 0x5 66 133 133 + * 0x5 0x7 66 133 200 + */ +#define CFG_SBC_MODCK_H 0x06 + +#define CFG_SBC_BOOT_LOW 1 /* only for HRCW */ +#undef CFG_SBC_BOOT_LOW + +/* What should the base address of the main FLASH be and how big is + * it (in MBytes)? This must contain TEXT_BASE from board/sbc8260/config.mk + * The main FLASH is whichever is connected to *CS0. U-Boot expects + * this to be the SIMM. + */ +#define CFG_FLASH0_BASE 0x80000000 +#define CFG_FLASH0_SIZE 16 + +/* What should the base address of the secondary FLASH be and how big + * is it (in Mbytes)? The secondary FLASH is whichever is connected + * to *CS6. U-Boot expects this to be the on board FLASH. If you don't + * want it enabled, don't define these constants. + */ +#define CFG_FLASH1_BASE 0 +#define CFG_FLASH1_SIZE 0 +#undef CFG_FLASH1_BASE +#undef CFG_FLASH1_SIZE + +/* What should be the base address of SDRAM DIMM and how big is + * it (in Mbytes)? +*/ +#define CFG_SDRAM0_BASE 0x00000000 +#define CFG_SDRAM0_SIZE 64 + +/* What should be the base address of SDRAM DIMM and how big is + * it (in Mbytes)? +*/ +#define CFG_SDRAM1_BASE 0x04000000 +#define CFG_SDRAM1_SIZE 32 + +/* What should be the base address of the LEDs and switch S0? + * If you don't want them enabled, don't define this. + */ +#define CFG_LED_BASE 0x00000000 + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere. + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on neither */ +#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ +#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ +#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */ + +#if ( CONFIG_ETHER_INDEX == 3 ) + +/* + * - Rx-CLK is CLK15 + * - Tx-CLK is CLK16 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Half Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16) +# define CFG_CPMFCR_RAMTYPE 0 +/*#define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */ +# define CFG_FCC_PSMR 0 + +#else /* CONFIG_ETHER_INDEX */ +# error "on RPX Super ethernet must be FCC3" +#endif /* CONFIG_ETHER_INDEX */ + +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + + +/* Define this to reserve an entire FLASH sector (256 KB) for + * environment variables. Otherwise, the environment will be + * put in the same sector as U-Boot, and changing variables + * will erase U-Boot temporarily + */ +#define CFG_ENV_IN_OWN_SECT + +/* Define to allow the user to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* What should the console's baud rate be? */ +#define CONFIG_BAUDRATE 115200 + +/* Ethernet MAC address */ +#define CONFIG_ETHADDR 08:00:22:50:70:63 + +#define CONFIG_IPADDR 192.168.1.99 +#define CONFIG_SERVERIP 192.168.1.3 + +/* Set to a positive value to delay for running BOOTCOMMAND */ +#define CONFIG_BOOTDELAY -1 + +/* undef this to save memory */ +#define CFG_LONGHELP + +/* Monitor Command Prompt */ +#define CFG_PROMPT "=> " + +/* What U-Boot subsytems do you want enabled? */ +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_IMMAP | \ + CFG_CMD_ASKENV | \ + CFG_CMD_ECHO | \ + CFG_CMD_I2C | \ + CFG_CMD_REGINFO & \ + ~CFG_CMD_KGDB ) + +/* Where do the internal registers live? */ +#define CFG_IMMR 0xF0000000 + +/* Where do the on board registers (CS4) live? */ +#define CFG_REGS_BASE 0xFA000000 + +/***************************************************************************** + * + * You should not have to modify any of the following settings + * + *****************************************************************************/ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_RPXSUPER 1 /* on an Embedded Planet RPX Super Board */ + +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +# define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +/* Print Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT)+16) + +#define CFG_MAXARGS 8 /* max number of command args */ + +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x04000000 /* memtest works on */ +#define CFG_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +#define CFG_FLASH_BASE CFG_FLASH0_BASE +#define CFG_SDRAM_BASE CFG_SDRAM0_BASE + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + */ +#if defined(CFG_SBC_BOOT_LOW) +# define CFG_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) +#else +# define CFG_SBC_HRCW_BOOT_FLAGS (0) +#endif /* defined(CFG_SBC_BOOT_LOW) */ + +/* get the HRCW ISB field from CFG_IMMR */ +#define CFG_SBC_HRCW_IMMR ( ((CFG_IMMR & 0x10000000) >> 10) |\ + ((CFG_IMMR & 0x01000000) >> 7) |\ + ((CFG_IMMR & 0x00100000) >> 4) ) + +#define CFG_HRCW_MASTER (HRCW_BPS11 |\ + HRCW_DPPC11 |\ + CFG_SBC_HRCW_IMMR |\ + HRCW_MMR00 |\ + HRCW_LBPC11 |\ + HRCW_APPC10 |\ + HRCW_CS10PC00 |\ + (CFG_SBC_MODCK_H & HRCW_MODCK_H1111) |\ + CFG_SBC_HRCW_BOOT_FLAGS) + +/* no slaves */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Note also that the logic that sets CFG_RAMBOOT is platform dependent. + */ +#define CFG_MONITOR_BASE (CFG_FLASH0_BASE + 0x00F00000) + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ + +#ifndef CFG_RAMBOOT +# define CFG_ENV_IS_IN_FLASH 1 + +# ifdef CFG_ENV_IN_OWN_SECT +# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +# define CFG_ENV_SECT_SIZE 0x40000 +# else +# define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CFG_ENV_SECT_SIZE) +# define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ +# define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */ +# endif /* CFG_ENV_IN_OWN_SECT */ +#else +# define CFG_ENV_IS_IN_NVRAM 1 +# define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +# define CFG_ENV_SIZE 0x200 +#endif /* CFG_RAMBOOT */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (/*HID0_ICE |*/\ + /*HID0_DCE |*/\ + HID0_ICFI |\ + HID0_DCI |\ + HID0_IFEM |\ + HID0_ABE) + +#define CFG_HID0_FINAL (/*HID0_ICE |*/\ + HID0_IFEM |\ + HID0_ABE |\ + HID0_EMCP) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register + *----------------------------------------------------------------------- + */ +#define CFG_RMR 0 + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CFG_BCR (BCR_EBM |\ + BCR_PLDP |\ + BCR_EAV |\ + BCR_NPQM0) + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ + +#define CFG_SIUMCR (SIUMCR_L2CPC01 |\ + SIUMCR_APPC10 |\ + SIUMCR_CS10PC01) + + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#define CFG_SYPCR (SYPCR_SWTC |\ + SYPCR_BMT |\ + SYPCR_PBME |\ + SYPCR_LBME |\ + SYPCR_SWRI |\ + SYPCR_SWP) + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC |\ + TMCNTSC_ALR |\ + TMCNTSC_TCF |\ + TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS |\ + PISCR_PTF |\ + PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + */ +#define CFG_SCCR (SCCR_DFBRG01) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90) + * 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Hitachi HM5225325FBP-B60) + * 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Hitachi HM5225325FBP-B60) + * 3 unused + * 4 60x GPCM 8 bit Board Regs, LEDs, switches + * 5 unused + * 6 unused + * 7 unused + * 8 PCMCIA + * 9 unused + * 10 unused + * 11 unused +*/ + +/* Bank 0 - FLASH + * + */ +#define CFG_BR0_PRELIM ((CFG_FLASH0_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_DECC_NONE |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH0_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_6_CLK |\ + ORxG_EHTR) + +/* Bank 1 - SDRAM + * + */ +#define CFG_BR1_PRELIM ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A8 |\ + ORxS_NUMR_12 |\ + ORxS_IBID) + +#define CFG_PSDMR 0x014DA412 +#define CFG_PSRT 0x79 + + +/* Bank 2 - SDRAM + * + */ +#define CFG_BR2_PRELIM ((CFG_SDRAM1_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_SDRAM_L |\ + BRx_V) + +#define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM1_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A9 |\ + ORxS_NUMR_12) + +#define CFG_LSDMR 0x0169A512 +#define CFG_LSRT 0x79 + +#define CFG_MPTPR (0x0800 & MPTPR_PTP_MSK) + +/* Bank 4 - On board registers + * + */ +#define CFG_BR4_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR4_PRELIM (ORxG_AM_MSK |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_5_CLK |\ + ORxG_TRLX) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ + + -- cgit v1.2.3