From 993cad9364c6b87ae429d1ed1130d8153f6f027e Mon Sep 17 00:00:00 2001 From: wdenk Date: Thu, 26 Jun 2003 22:04:09 +0000 Subject: * Patches by Robert Schwebel, 26 Jun 2003: - logdl - csb226 - innokom * Patch by Pantelis Antoniou, 25 Jun 2003: update NetVia with V2 board support --- include/configs/csb226.h | 303 +++++++++++++++++++++++++++++++++++++++++++---- 1 file changed, 281 insertions(+), 22 deletions(-) (limited to 'include/configs/csb226.h') diff --git a/include/configs/csb226.h b/include/configs/csb226.h index 2806b6dd0..a257b82eb 100644 --- a/include/configs/csb226.h +++ b/include/configs/csb226.h @@ -63,17 +63,17 @@ #define CONFIG_BAUDRATE 19200 #undef CONFIG_MISC_INIT_R /* not used yet */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_NET) +#define CONFIG_COMMANDS (CFG_CMD_BDI|CFG_CMD_LOADB|CFG_CMD_IMI|CFG_CMD_FLASH|CFG_CMD_MEMORY|CFG_CMD_NET|CFG_CMD_ENV|CFG_CMD_RUN|CFG_CMD_ASKENV|CFG_CMD_ECHO|CFG_CMD_DHCP|CFG_CMD_CACHE) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include #define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTARGS "console=ttyS0,19200 ip=dhcp root=/dev/nfs, ether=0,0x08000000,eth0" +#define CONFIG_BOOTARGS "console=ttyS0,19200 ip=192.168.1.10,192.168.1.5,,255,255,255,0,csb root=/dev/nfs, ether=0,0x08000000,eth0" #define CONFIG_ETHADDR FF:FF:FF:FF:FF:FF #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_IPADDR 192.168.1.56 -#define CONFIG_SERVERIP 192.168.1.2 +#define CONFIG_SERVERIP 192.168.1.5 #define CONFIG_BOOTCOMMAND "bootm 0x40000" #define CONFIG_SHOW_BOOT_PROGRESS @@ -125,6 +125,13 @@ /* valid baudrates */ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +/* + * Network chip + */ +#define CONFIG_DRIVER_CS8900 1 +#define CS8900_BUS32 1 +#define CS8900_BASE 0x08000000 + /* * Stack sizes * @@ -151,25 +158,276 @@ #define CFG_FLASH_BASE PHYS_FLASH_1 +# if 0 +/* FIXME: switch to _documented_ registers */ /* * GPIO settings + * + * GP15 == nCS1 is 1 + * GP24 == SFRM is 1 + * GP25 == TXD is 1 + * GP33 == nCS5 is 1 + * GP39 == FFTXD is 1 + * GP41 == RTS is 1 + * GP47 == TXD is 1 + * GP49 == nPWE is 1 + * GP62 == LED_B is 1 + * GP63 == TDM_OE is 1 + * GP78 == nCS2 is 1 + * GP79 == nCS3 is 1 + * GP80 == nCS4 is 1 + */ +#define CFG_GPSR0_VAL 0x03008000 +#define CFG_GPSR1_VAL 0xC0028282 +#define CFG_GPSR2_VAL 0x0001C000 + +/* GP02 == DON_RST is 0 + * GP23 == SCLK is 0 + * GP45 == USB_ACT is 0 + * GP60 == PLLEN is 0 + * GP61 == LED_A is 0 + * GP73 == SWUPD_LED is 0 + */ +#define CFG_GPCR0_VAL 0x00800004 +#define CFG_GPCR1_VAL 0x30002000 +#define CFG_GPCR2_VAL 0x00000100 + +/* GP00 == DON_READY is input + * GP01 == DON_OK is input + * GP02 == DON_RST is output + * GP03 == RESET_IND is input + * GP07 == RES11 is input + * GP09 == RES12 is input + * GP11 == SWUPDATE is input + * GP14 == nPOWEROK is input + * GP15 == nCS1 is output + * GP17 == RES22 is input + * GP18 == RDY is input + * GP23 == SCLK is output + * GP24 == SFRM is output + * GP25 == TXD is output + * GP26 == RXD is input + * GP32 == RES21 is input + * GP33 == nCS5 is output + * GP34 == FFRXD is input + * GP35 == CTS is input + * GP39 == FFTXD is output + * GP41 == RTS is output + * GP42 == USB_OK is input + * GP45 == USB_ACT is output + * GP46 == RXD is input + * GP47 == TXD is output + * GP49 == nPWE is output + * GP58 == nCPUBUSINT is input + * GP59 == LANINT is input + * GP60 == PLLEN is output + * GP61 == LED_A is output + * GP62 == LED_B is output + * GP63 == TDM_OE is output + * GP64 == nDSPINT is input + * GP65 == STRAP0 is input + * GP67 == STRAP1 is input + * GP69 == STRAP2 is input + * GP70 == STRAP3 is input + * GP71 == STRAP4 is input + * GP73 == SWUPD_LED is output + * GP78 == nCS2 is output + * GP79 == nCS3 is output + * GP80 == nCS4 is output + */ +#define CFG_GPDR0_VAL 0x03808004 +#define CFG_GPDR1_VAL 0xF002A282 +#define CFG_GPDR2_VAL 0x0001C200 + +/* GP15 == nCS1 is AF10 + * GP18 == RDY is AF01 + * GP23 == SCLK is AF10 + * GP24 == SFRM is AF10 + * GP25 == TXD is AF10 + * GP26 == RXD is AF01 + * GP33 == nCS5 is AF10 + * GP34 == FFRXD is AF01 + * GP35 == CTS is AF01 + * GP39 == FFTXD is AF10 + * GP41 == RTS is AF10 + * GP46 == RXD is AF10 + * GP47 == TXD is AF01 + * GP49 == nPWE is AF10 + * GP78 == nCS2 is AF10 + * GP79 == nCS3 is AF10 + * GP80 == nCS4 is AF10 */ -#define CFG_GPSR0_VAL 0xFFFFFFFF -#define CFG_GPSR1_VAL 0xFFFFFFFF -#define CFG_GPSR2_VAL 0xFFFFFFFF -#define CFG_GPCR0_VAL 0x08022080 -#define CFG_GPCR1_VAL 0x00000000 -#define CFG_GPCR2_VAL 0x00000000 -#define CFG_GPDR0_VAL 0xCD82A878 -#define CFG_GPDR1_VAL 0xFCFFAB80 -#define CFG_GPDR2_VAL 0x0001FFFF #define CFG_GAFR0_L_VAL 0x80000000 -#define CFG_GAFR0_U_VAL 0xA5254010 -#define CFG_GAFR1_L_VAL 0x599A9550 -#define CFG_GAFR1_U_VAL 0xAAA5AAAA -#define CFG_GAFR2_L_VAL 0xAAAAAAAA +#define CFG_GAFR0_U_VAL 0x001A8010 +#define CFG_GAFR1_L_VAL 0x60088058 +#define CFG_GAFR1_U_VAL 0x00000008 +#define CFG_GAFR2_L_VAL 0xA0000000 #define CFG_GAFR2_U_VAL 0x00000002 + +/* FIXME: set GPIO_RER/FER */ + +/* RDH = 1 + * PH = 1 + * VFS = 1 + * BFS = 1 + * SSS = 1 + */ +#define CFG_PSSR_VAL 0x37 + +/* + * Memory settings + * + * This is the configuration for nCS0/1 -> flash banks + * configuration for nCS1: + * [31] 0 - Slower Device + * [30:28] 010 - CS deselect to CS time: 2*(2*MemClk) = 40 ns + * [27:24] 0101 - Address to data valid in bursts: (5+1)*MemClk = 60 ns + * [23:20] 1011 - " for first access: (11+2)*MemClk = 130 ns + * [19] 1 - 16 Bit bus width + * [18:16] 000 - nonburst RAM or FLASH + * configuration for nCS0: + * [15] 0 - Slower Device + * [14:12] 010 - CS deselect to CS time: 2*(2*MemClk) = 40 ns + * [11:08] 0101 - Address to data valid in bursts: (5+1)*MemClk = 60 ns + * [07:04] 1011 - " for first access: (11+2)*MemClk = 130 ns + * [03] 1 - 16 Bit bus width + * [02:00] 000 - nonburst RAM or FLASH + */ +#define CFG_MSC0_VAL 0x25b825b8 /* flash banks */ + +/* This is the configuration for nCS2/3 -> TDM-Switch, DSP + * configuration for nCS3: DSP + * [31] 0 - Slower Device + * [30:28] 001 - RRR3: CS deselect to CS time: 1*(2*MemClk) = 20 ns + * [27:24] 0010 - RDN3: Address to data valid in bursts: (2+1)*MemClk = 30 ns + * [23:20] 0011 - RDF3: Address for first access: (3+1)*MemClk = 40 ns + * [19] 1 - 16 Bit bus width + * [18:16] 100 - variable latency I/O + * configuration for nCS2: TDM-Switch + * [15] 0 - Slower Device + * [14:12] 101 - RRR2: CS deselect to CS time: 5*(2*MemClk) = 100 ns + * [11:08] 1001 - RDN2: Address to data valid in bursts: (9+1)*MemClk = 100 ns + * [07:04] 0011 - RDF2: Address for first access: (3+1)*MemClk = 40 ns + * [03] 1 - 16 Bit bus width + * [02:00] 100 - variable latency I/O + */ +#define CFG_MSC1_VAL 0x123C593C /* TDM switch, DSP */ + +/* This is the configuration for nCS4/5 -> ExtBus, LAN Controller + * + * configuration for nCS5: LAN Controller + * [31] 0 - Slower Device + * [30:28] 001 - RRR5: CS deselect to CS time: 1*(2*MemClk) = 20 ns + * [27:24] 0010 - RDN5: Address to data valid in bursts: (2+1)*MemClk = 30 ns + * [23:20] 0011 - RDF5: Address for first access: (3+1)*MemClk = 40 ns + * [19] 1 - 16 Bit bus width + * [18:16] 100 - variable latency I/O + * configuration for nCS4: ExtBus + * [15] 0 - Slower Device + * [14:12] 110 - RRR4: CS deselect to CS time: 6*(2*MemClk) = 120 ns + * [11:08] 1100 - RDN4: Address to data valid in bursts: (12+1)*MemClk = 130 ns + * [07:04] 1101 - RDF4: Address for first access: 13->(15+1)*MemClk = 160 ns + * [03] 1 - 16 Bit bus width + * [02:00] 100 - variable latency I/O + */ +#define CFG_MSC2_VAL 0x123C6CDC /* extra bus, LAN controller */ + +/* MDCNFG: SDRAM Configuration Register + * + * [31:29] 000 - reserved + * [28] 0 - no SA1111 compatiblity mode + * [27] 0 - latch return data with return clock + * [26] 0 - alternate addressing for pair 2/3 + * [25:24] 00 - timings + * [23] 0 - internal banks in lower partition 2/3 (not used) + * [22:21] 00 - row address bits for partition 2/3 (not used) + * [20:19] 00 - column address bits for partition 2/3 (not used) + * [18] 0 - SDRAM partition 2/3 width is 32 bit + * [17] 0 - SDRAM partition 3 disabled + * [16] 0 - SDRAM partition 2 disabled + * [15:13] 000 - reserved + * [12] 1 - SA1111 compatiblity mode + * [11] 1 - latch return data with return clock + * [10] 0 - no alternate addressing for pair 0/1 + * [09:08] 01 - tRP=2*MemClk CL=2 tRCD=2*MemClk tRAS=5*MemClk tRC=8*MemClk + * [7] 1 - 4 internal banks in lower partition pair + * [06:05] 10 - 13 row address bits for partition 0/1 + * [04:03] 01 - 9 column address bits for partition 0/1 + * [02] 0 - SDRAM partition 0/1 width is 32 bit + * [01] 0 - disable SDRAM partition 1 + * [00] 1 - enable SDRAM partition 0 + */ +/* use the configuration above but disable partition 0 */ +#define CFG_MDCNFG_VAL 0x000019c8 + +/* MDREFR: SDRAM Refresh Control Register + * + * [32:26] 0 - reserved + * [25] 0 - K2FREE: not free running + * [24] 0 - K1FREE: not free running + * [23] 1 - K0FREE: not free running + * [22] 0 - SLFRSH: self refresh disabled + * [21] 0 - reserved + * [20] 0 - APD: no auto power down + * [19] 0 - K2DB2: SDCLK2 is MemClk + * [18] 0 - K2RUN: disable SDCLK2 + * [17] 0 - K1DB2: SDCLK1 is MemClk + * [16] 1 - K1RUN: enable SDCLK1 + * [15] 1 - E1PIN: SDRAM clock enable + * [14] 1 - K0DB2: SDCLK0 is MemClk + * [13] 0 - K0RUN: disable SDCLK0 + * [12] 1 - E0PIN: disable SDCKE0 + * [11:00] 000000011000 - (64ms/8192)*MemClkFreq/32 = 24 + */ +#define CFG_MDREFR_VAL 0x0081D018 + +/* MDMRS: Mode Register Set Configuration Register + * + * [31] 0 - reserved + * [30:23] 00000000- MDMRS2: SDRAM2/3 MRS Value. (not used) + * [22:20] 000 - MDCL2: SDRAM2/3 Cas Latency. (not used) + * [19] 0 - MDADD2: SDRAM2/3 burst Type. Fixed to sequential. (not used) + * [18:16] 010 - MDBL2: SDRAM2/3 burst Length. Fixed to 4. (not used) + * [15] 0 - reserved + * [14:07] 00000000- MDMRS0: SDRAM0/1 MRS Value. + * [06:04] 010 - MDCL0: SDRAM0/1 Cas Latency. + * [03] 0 - MDADD0: SDRAM0/1 burst Type. Fixed to sequential. + * [02:00] 010 - MDBL0: SDRAM0/1 burst Length. Fixed to 4. + */ +#define CFG_MDMRS_VAL 0x00020022 + +/* + * PCMCIA and CF Interfaces + */ +#define CFG_MECR_VAL 0x00000000 +#define CFG_MCMEM0_VAL 0x00000000 +#define CFG_MCMEM1_VAL 0x00000000 +#define CFG_MCATT0_VAL 0x00000000 +#define CFG_MCATT1_VAL 0x00000000 +#define CFG_MCIO0_VAL 0x00000000 +#define CFG_MCIO1_VAL 0x00000000 +#endif + +/* + * GPIO settings + */ +#define CFG_GPSR0_VAL 0xFFFFFFFF +#define CFG_GPSR1_VAL 0xFFFFFFFF +#define CFG_GPSR2_VAL 0xFFFFFFFF +#define CFG_GPCR0_VAL 0x08022080 +#define CFG_GPCR1_VAL 0x00000000 +#define CFG_GPCR2_VAL 0x00000000 +#define CFG_GPDR0_VAL 0xCD82A878 +#define CFG_GPDR1_VAL 0xFCFFAB80 +#define CFG_GPDR2_VAL 0x0001FFFF +#define CFG_GAFR0_L_VAL 0x80000000 +#define CFG_GAFR0_U_VAL 0xA5254010 +#define CFG_GAFR1_L_VAL 0x599A9550 +#define CFG_GAFR1_U_VAL 0xAAA5AAAA +#define CFG_GAFR2_L_VAL 0xAAAAAAAA +#define CFG_GAFR2_U_VAL 0x00000002 + /* FIXME: set GPIO_RER/FER */ #define CFG_PSSR_VAL 0x20 @@ -177,12 +435,13 @@ /* * Memory settings */ -#define CFG_MSC0_VAL 0x2EF025D0 -#define CFG_MSC1_VAL 0x00003F64 -#define CFG_MSC2_VAL 0x00000000 -#define CFG_MDCNFG_VAL 0x09a909a9 -#define CFG_MDREFR_VAL 0x03ca0030 -#define CFG_MDMRS_VAL 0x00220022 + +#define CFG_MSC0_VAL 0x2ef15af0 +#define CFG_MSC1_VAL 0x00003ff4 +#define CFG_MSC2_VAL 0x7ff07ff0 +#define CFG_MDCNFG_VAL 0x09a909a9 +#define CFG_MDREFR_VAL 0x038ff030 +#define CFG_MDMRS_VAL 0x00220022 /* * PCMCIA and CF Interfaces -- cgit v1.2.3