From c11da194545d2f4bbb54be1bb5e504e20ce8c16c Mon Sep 17 00:00:00 2001 From: Niklaus Giger Date: Wed, 1 Oct 2008 14:46:13 +0200 Subject: ppc4xx: Update configs for Netstal boards I reorganized my config files, putting the common stuff into netstal-common.h (got the idea by looking a amcc-common.h from Stefan). Added stuff to boot the new powerpc linux via NFS (only tested with HCU4). Signed-off-by: Niklaus Giger Signed-off-by: Stefan Roese --- include/configs/hcu4.h | 100 +++++-------------------------------------------- 1 file changed, 10 insertions(+), 90 deletions(-) (limited to 'include/configs/hcu4.h') diff --git a/include/configs/hcu4.h b/include/configs/hcu4.h index 9b03ac2f4..369b36894 100644 --- a/include/configs/hcu4.h +++ b/include/configs/hcu4.h @@ -35,6 +35,12 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_405GP 1 #define CONFIG_4xx 1 +#define CONFIG_HOSTNAME hcu4 + +/* + * Include common defines/options for all boards produced by Netstal Maschinen + */ +#include "netstal-common.h" #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ @@ -80,25 +86,12 @@ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_SERIAL_MULTI 1 -/* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */ #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 691200 -/* Size (bytes) of interrupt driven serial port buffer. - * Set to 0 to use polling instead of interrupts. - * Setting to 0 will also disable RTS/CTS handshaking. - */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO - /* Set console baudrate to 9600 */ #define CONFIG_BAUDRATE 9600 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Flash *----------------------------------------------------------------------*/ @@ -149,74 +142,12 @@ *----------------------------------------------------------------------*/ #define CONFIG_SYS_SPD_BUS_NUM 0 -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* This is the 7bit address of the device, not including P. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#undef CONFIG_SYS_I2C_MULTI_EEPROMS - +#define CONFIG_IPADDR 172.25.1.14 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#define CONFIG_HOSTNAME hcu4 -#define CONFIG_IPADDR 172.25.1.99 -#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE -#define CONFIG_SERVERIP 172.25.1.3 - -#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* @16 MB */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "loadaddr=0x01000000\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/home/diagnose/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/hcu4/uImage\0" \ - "load=tftp 100000 hcu4/u-boot.bin\0" \ - "update=protect off FFFB0000 FFFFFFFF;era FFFB0000 FFFFFFFF;" \ - "cp.b 100000 FFFB0000 50000\0" \ - "upd=run load update\0" \ - "vx_rom=hcu4/hcu4_vx_rom\0" \ - "vx=tftp ${loadaddr} ${vx_rom};run vxargs; bootvx\0" \ - "vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}" \ - " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_NETSTAL_DEF_ENV \ + CONFIG_NETSTAL_DEF_ENV_POWERPC \ "" -#define CONFIG_BOOTCOMMAND "run vx" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address */ - -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ - -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & desC */ /* * BOOTP options @@ -285,13 +216,6 @@ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup @@ -348,8 +272,4 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ -- cgit v1.2.3