linux.git/drivers/iio/light/Makefile, branch master

staging: iio: tsl2583: move out of staging

2016-11-13T13:07:33+00:00

Move tsl2580, tsl2581, tsl2583 driver out of staging into mainline. Signed-off-by: Brian Masney Signed-off-by: Jonathan Cameron

staging: iio: isl29018: move out of staging

2016-10-23T18:33:56+00:00

Move ISL29018/ISL29023/ISL29035 driver out of staging into mainline. Signed-off-by: Brian Masney Signed-off-by: Jonathan Cameron

iio: light: Add driver for Silabs si1132, si1141/2/3 and si1145/6/7 ambient light, uv index and proximity sensors

2016-09-18T18:56:39+00:00

The si114x supports x=1,2,3 IR LEDs for proximity sensing together with visible and IR ambient light sensing (ALS). Newer parts (si1132, si1145/6/7) can measure UV light and compute an UV index This was tested on si1143 and si1145 Signed-off-by: Peter Meerwald-Stadler Signed-off-by: Crestez Dan Leonard Signed-off-by: Jonathan Cameron

max44000: Initial support

2016-04-24T09:06:55+00:00

This just adds support for reporting illuminance with default settings. Important default registers are written on probe because the device otherwise lacks a reset function. Signed-off-by: Crestez Dan Leonard Signed-off-by: Jonathan Cameron

iio: Add Vishay VEML6070 UV A light sensor driver

2016-04-19T18:58:16+00:00

ultraviolet (UV) light sensor with I2C interface with a peak sensitivity at 355 nm strangely, chip uses two addresses 0x38 and 0x39 for LSB and MSB data, resp. datasheet: http://www.vishay.com/docs/84277/veml6070.pdf Signed-off-by: Peter Meerwald-Stadler Signed-off-by: Jonathan Cameron

iio: light: new driver for the ROHM BH1780

2016-04-16T19:51:50+00:00

This is a reimplementation of the old misc device driver for the ROHM BH1780 ambient light sensor (drivers/misc/bh1780gli.c). Differences from the old driver: - Uses the IIO framework - Uses runtime PM to idle the hardware after 5 seconds - No weird custom power management from userspace - No homebrewn values in sysfs This uses the same (undocumented) device tree compatible-string as the old driver ("rohm,bh1780gli"). Cc: Arnd Bergmann Cc: Ulf Hansson Cc: Daniel Mack Cc: Peter Meerwald-Stadler Signed-off-by: Linus Walleij Reviewed-by: Ulf Hansson Signed-off-by: Jonathan Cameron

iio: light: Add support for UPISEMI uS5182d als and proximity sensor

2015-09-23T19:23:27+00:00

Add support for UPISEMI us5182d als and proximity sensor. Supports raw readings. Data sheet for this device can be found here: http://www.upi-semi.com/temp/uS5182D-DS-P0103-temp.pdf Signed-off-by: Adriana Reus Signed-off-by: Jonathan Cameron

iio: light: add APDS9960 ALS + promixity driver

2015-08-31T15:23:09+00:00

APDS9960 is a combination of ALS, proximity, and gesture sensors. This patch adds support for these functions along with gain control, integration time, and event thresholds. Signed-off-by: Matt Ranostay Signed-off-by: Jonathan Cameron

iio: light: Add support for TXC PA12 als and proximity sensor

2015-07-20T17:41:21+00:00

Add support for TXC PA12203001 als and proximity sensor. Support for raw illuminance and proximity readings. Signed-off-by: Adriana Reus Signed-off-by: Jonathan Cameron

iio: light: add support for TI's opt3001 light sensor

2015-07-20T17:41:21+00:00

TI's opt3001 light sensor is a simple and yet powerful little device. The device provides 99% IR rejection, automatic full-scale, very low power consumption and measurements from 0.01 to 83k lux. This patch adds support for that device using the IIO framework. See http://www.ti.com/product/opt3001 for more information. Signed-off-by: Felipe Balbi Signed-off-by: Andreas Dannenberg Signed-off-by: Jonathan Cameron