linux.git/drivers/usb/serial, branch master

USB: serial: pl2303: add ATEN device ID

2017-01-31T16:27:04+00:00

Seems that ATEN serial-to-usb devices using pl2303 exist with different device ids. This patch adds a missing device ID so it is recognised by the driver. Signed-off-by: Marcel J.E. Mol Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add device ID for HP lt2523 (Novatel E371)

2017-01-24T11:07:28+00:00

Yet another laptop vendor rebranded Novatel E371. Cc: stable@vger.kernel.org Signed-off-by: Bjørn Mork Signed-off-by: Johan Hovold

USB: serial: qcserial: add Dell DW5570 QDL

2017-01-19T08:08:37+00:00

The Dell DW5570 is a re-branded Sierra Wireless MC8805 which will by default boot with vid 0x413c and pid 0x81a3. When triggered QDL download mode, the device switches to pid 0x81a6 and provides the standard TTY used for firmware upgrade. Cc: Signed-off-by: Aleksander Morgado Signed-off-by: Johan Hovold

USB: serial: ch341: fix control-message error handling

2017-01-11T11:08:57+00:00

A short control transfer would currently fail to be detected, something which could lead to stale buffer data being used as valid input. Check for short transfers, and make sure to log any transfer errors. Note that this also avoids leaking heap data to user space (TIOCMGET) and the remote device (break control). Fixes: 6ce76104781a ("USB: Driver for CH341 USB-serial adaptor") Cc: stable Signed-off-by: Johan Hovold

USB: serial: kl5kusb105: fix line-state error handling

2017-01-10T15:42:26+00:00

The current implementation failed to detect short transfers when attempting to read the line state, and also, to make things worse, logged the content of the uninitialised heap transfer buffer. Fixes: abf492e7b3ae ("USB: kl5kusb105: fix DMA buffers on stack") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable Reviewed-by: Greg Kroah-Hartman Signed-off-by: Johan Hovold

USB: serial: ch341: fix baud rate and line-control handling

2017-01-09T13:55:40+00:00

Revert to using direct register writes to set the divisor and line-control registers. A recent change switched to using the init vendor command to update these registers, something which also enabled support for CH341A devices. It turns out that simply setting bit 7 in the divisor register is sufficient to support CH341A and specifically prevent data from being buffered until a full endpoint-size packet (32 bytes) has been received. Using the init command also had the side-effect of temporarily deasserting the DTR/RTS signals on every termios change (including initialisation on open) something which for example could cause problems in setups where DTR is used to trigger a reset. Fixes: 4e46c410e050 ("USB: serial: ch341: reinitialize chip on reconfiguration") Signed-off-by: Johan Hovold

USB: serial: ch341: fix line settings after reset-resume

2017-01-09T13:55:39+00:00

A recent change added support for modifying the default line-control settings, but did not make sure that the modified settings were used as part of reconfiguration after a device has been reset during resume. This caused a port that was open before suspend to be unusable until being closed and reopened. Fixes: ba781bdf8662 ("USB: serial: ch341: add support for parity, frame length, stop bits") Signed-off-by: Johan Hovold

USB: serial: ch341: fix resume after reset

2017-01-09T13:55:38+00:00

Fix reset-resume handling which failed to resubmit the read and interrupt URBs, thereby leaving a port that was open before suspend in a broken state until closed and reopened. Fixes: 1ded7ea47b88 ("USB: ch341 serial: fix port number changed after resume") Fixes: 2bfd1c96a9fb ("USB: serial: ch341: remove reset_resume callback") Cc: stable Signed-off-by: Johan Hovold

USB: serial: ch341: fix open error handling

2017-01-09T13:55:38+00:00

Make sure to stop the interrupt URB before returning on errors during open. Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Cc: stable Signed-off-by: Johan Hovold

USB: serial: ch341: fix modem-control and B0 handling

2017-01-09T13:55:37+00:00

The modem-control signals are managed by the tty-layer during open and should not be asserted prematurely when set_termios is called from driver open. Also make sure that the signals are asserted only when changing speed from B0. Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Cc: stable Signed-off-by: Johan Hovold