gma500: initial medfield merge

We need to merge this ahead of some of the cleanup because a lot of needed
cleanup spans both new and old chips. If we try and clean up and the merge
we end up fighting ourselves.

Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[With a load of the cleanup stuff folded in, register stuff reworked sanely]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

1 files changed, 1024 insertions, 0 deletions

diff --git a/drivers/gpu/drm/gma500/mdfld_dsi_dpi.c b/drivers/gpu/drm/gma500/mdfld_dsi_dpi.c
new file mode 100644
index 000000000000..fc0df28a668c
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_dsi_dpi.c
@@ -0,0 +1,1024 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * jim liu <jim.liu@intel.com>
+ * Jackie Li<yaodong.li@intel.com>
+ */
+
+#include "mdfld_dsi_dpi.h"
+#include "mdfld_output.h"
+#include "mdfld_dsi_pkg_sender.h"
+#include "psb_drv.h"
+#include "tc35876x-dsi-lvds.h"
+
+static void mdfld_dsi_dpi_shut_down(struct mdfld_dsi_dpi_output *output,
+								int pipe);
+
+static void mdfld_wait_for_HS_DATA_FIFO(struct drm_device *dev, u32 pipe)
+{
+	u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
+	int timeout = 0;
+
+	udelay(500);
+
+	/* This will time out after approximately 2+ seconds */
+	while ((timeout < 20000) &&
+		(REG_READ(gen_fifo_stat_reg) & DSI_FIFO_GEN_HS_DATA_FULL)) {
+		udelay(100);
+		timeout++;
+	}
+
+	if (timeout == 20000)
+		DRM_INFO("MIPI: HS Data FIFO was never cleared!\n");
+}
+
+static void mdfld_wait_for_HS_CTRL_FIFO(struct drm_device *dev, u32 pipe)
+{
+	u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
+	int timeout = 0;
+
+	udelay(500);
+
+	/* This will time out after approximately 2+ seconds */
+	while ((timeout < 20000) && (REG_READ(gen_fifo_stat_reg)
+					& DSI_FIFO_GEN_HS_CTRL_FULL)) {
+		udelay(100);
+		timeout++;
+	}
+	if (timeout == 20000)
+		DRM_INFO("MIPI: HS CMD FIFO was never cleared!\n");
+}
+
+static void mdfld_wait_for_DPI_CTRL_FIFO(struct drm_device *dev, u32 pipe)
+{
+	u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
+	int timeout = 0;
+
+	udelay(500);
+
+	/* This will time out after approximately 2+ seconds */
+	while ((timeout < 20000) && ((REG_READ(gen_fifo_stat_reg) &
+					DPI_FIFO_EMPTY) != DPI_FIFO_EMPTY)) {
+		udelay(100);
+		timeout++;
+	}
+
+	if (timeout == 20000)
+		DRM_ERROR("MIPI: DPI FIFO was never cleared\n");
+}
+
+static void mdfld_wait_for_SPL_PKG_SENT(struct drm_device *dev, u32 pipe)
+{
+	u32 intr_stat_reg = MIPI_INTR_STAT_REG(pipe);
+	int timeout = 0;
+
+	udelay(500);
+
+	/* This will time out after approximately 2+ seconds */
+	while ((timeout < 20000) && (!(REG_READ(intr_stat_reg)
+					& DSI_INTR_STATE_SPL_PKG_SENT))) {
+		udelay(100);
+		timeout++;
+	}
+
+	if (timeout == 20000)
+                DRM_ERROR("MIPI: SPL_PKT_SENT_INTERRUPT was not sent successfully!\n");
+}
+
+/* For TC35876X */
+
+static void dsi_set_device_ready_state(struct drm_device *dev, int state,
+				int pipe)
+{
+	REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), !!state, 0, 0);
+}
+
+static void dsi_set_pipe_plane_enable_state(struct drm_device *dev,
+							int state, int pipe)
+{
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	u32 pipeconf_reg = PIPEACONF;
+	u32 dspcntr_reg = DSPACNTR;
+
+	u32 dspcntr = dev_priv->dspcntr[pipe];
+	u32 mipi = MIPI_PORT_EN | PASS_FROM_SPHY_TO_AFE | SEL_FLOPPED_HSTX;
+
+	if (pipe) {
+		pipeconf_reg = PIPECCONF;
+		dspcntr_reg = DSPCCNTR;
+	} else
+		mipi &= (~0x03);
+
+	if (state) {
+		/*Set up pipe */
+		REG_WRITE(pipeconf_reg, BIT(31));
+
+		if (REG_BIT_WAIT(pipeconf_reg, 1, 30))
+			dev_err(&dev->pdev->dev, "%s: Pipe enable timeout\n",
+				__func__);
+
+		/*Set up display plane */
+		REG_WRITE(dspcntr_reg, dspcntr);
+	} else {
+		u32 dspbase_reg = pipe ? MDFLD_DSPCBASE : MRST_DSPABASE;
+
+		/* Put DSI lanes to ULPS to disable pipe */
+		REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 2, 2, 1);
+		REG_READ(MIPI_DEVICE_READY_REG(pipe)); /* posted write? */
+
+		/* LP Hold */
+		REG_FLD_MOD(MIPI_PORT_CONTROL(pipe), 0, 16, 16);
+		REG_READ(MIPI_PORT_CONTROL(pipe)); /* posted write? */
+
+		/* Disable display plane */
+		REG_FLD_MOD(dspcntr_reg, 0, 31, 31);
+
+		/* Flush the plane changes ??? posted write? */
+		REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
+		REG_READ(dspbase_reg);
+
+		/* Disable PIPE */
+		REG_FLD_MOD(pipeconf_reg, 0, 31, 31);
+
+		if (REG_BIT_WAIT(pipeconf_reg, 0, 30))
+			dev_err(&dev->pdev->dev, "%s: Pipe disable timeout\n",
+				__func__);
+
+		if (REG_BIT_WAIT(MIPI_GEN_FIFO_STAT_REG(pipe), 1, 28))
+			dev_err(&dev->pdev->dev, "%s: FIFO not empty\n",
+				__func__);
+	}
+}
+
+static void mdfld_dsi_configure_down(struct mdfld_dsi_encoder *dsi_encoder,
+								int pipe)
+{
+	struct mdfld_dsi_dpi_output *dpi_output =
+				MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+
+	if (!dev_priv->dpi_panel_on[pipe]) {
+		dev_err(dev->dev, "DPI panel is already off\n");
+		return;
+	}
+	tc35876x_toshiba_bridge_panel_off(dev);
+	tc35876x_set_bridge_reset_state(dev, 1);
+	dsi_set_pipe_plane_enable_state(dev, 0, pipe);
+	mdfld_dsi_dpi_shut_down(dpi_output, pipe);
+	dsi_set_device_ready_state(dev, 0, pipe);
+}
+
+static void mdfld_dsi_configure_up(struct mdfld_dsi_encoder *dsi_encoder,
+								int pipe)
+{
+	struct mdfld_dsi_dpi_output *dpi_output =
+				MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+
+	if (dev_priv->dpi_panel_on[pipe]) {
+		dev_err(dev->dev, "DPI panel is already on\n");
+		return;
+	}
+
+	/* For resume path sequence */
+	mdfld_dsi_dpi_shut_down(dpi_output, pipe);
+	dsi_set_device_ready_state(dev, 0, pipe);
+
+	dsi_set_device_ready_state(dev, 1, pipe);
+	tc35876x_set_bridge_reset_state(dev, 0);
+	tc35876x_configure_lvds_bridge(dev);
+	mdfld_dsi_dpi_turn_on(dpi_output, pipe);  /* Send turn on command */
+	dsi_set_pipe_plane_enable_state(dev, 1, pipe);
+}
+/* End for TC35876X */
+
+/* ************************************************************************* *\
+ * FUNCTION: mdfld_dsi_tpo_ic_init
+ *
+ * DESCRIPTION:  This function is called only by mrst_dsi_mode_set and
+ *               restore_display_registers.  since this function does not
+ *               acquire the mutex, it is important that the calling function
+ *               does!
+\* ************************************************************************* */
+static void mdfld_dsi_tpo_ic_init(struct mdfld_dsi_config *dsi_config, u32 pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	u32 dcsChannelNumber = dsi_config->channel_num;
+	u32 gen_data_reg = MIPI_HS_GEN_DATA_REG(pipe);
+	u32 gen_ctrl_reg = MIPI_HS_GEN_CTRL_REG(pipe);
+	u32 gen_ctrl_val = GEN_LONG_WRITE;
+
+	DRM_INFO("Enter mrst init TPO MIPI display.\n");
+
+	gen_ctrl_val |= dcsChannelNumber << DCS_CHANNEL_NUMBER_POS;
+
+	/* Flip page order */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00008036);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x02 << WORD_COUNTS_POS));
+
+	/* 0xF0 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x005a5af0);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+
+	/* Write protection key */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x005a5af1);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+
+	/* 0xFC */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x005a5afc);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+
+	/* 0xB7 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x770000b7);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000044);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x05 << WORD_COUNTS_POS));
+
+	/* 0xB6 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x000a0ab6);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+
+	/* 0xF2 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x081010f2);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x4a070708);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x000000c5);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS));
+
+	/* 0xF8 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x024003f8);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x01030a04);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x0e020220);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000004);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x0d << WORD_COUNTS_POS));
+
+	/* 0xE2 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x398fc3e2);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x0000916f);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x06 << WORD_COUNTS_POS));
+
+	/* 0xB0 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x000000b0);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x02 << WORD_COUNTS_POS));
+
+	/* 0xF4 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x240242f4);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x78ee2002);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x2a071050);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x507fee10);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x10300710);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x14 << WORD_COUNTS_POS));
+
+	/* 0xBA */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x19fe07ba);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x101c0a31);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000010);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS));
+
+	/* 0xBB */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x28ff07bb);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x24280a31);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000034);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS));
+
+	/* 0xFB */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x535d05fb);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1b1a2130);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x221e180e);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x131d2120);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x535d0508);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1c1a2131);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x231f160d);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x111b2220);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x535c2008);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1f1d2433);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x2c251a10);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x2c34372d);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000023);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x31 << WORD_COUNTS_POS));
+
+	/* 0xFA */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x525c0bfa);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1c1c232f);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x2623190e);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x18212625);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x545d0d0e);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1e1d2333);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x26231a10);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1a222725);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x545d280f);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x21202635);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x31292013);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x31393d33);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000029);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x31 << WORD_COUNTS_POS));
+
+	/* Set DM */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x000100f7);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+}
+
+static u16 mdfld_dsi_dpi_to_byte_clock_count(int pixel_clock_count,
+						int num_lane, int bpp)
+{
+	return (u16)((pixel_clock_count * bpp) / (num_lane * 8));
+}
+
+/*
+ * Calculate the dpi time basing on a given drm mode @mode
+ * return 0 on success.
+ * FIXME: I was using proposed mode value for calculation, may need to
+ * use crtc mode values later
+ */
+int mdfld_dsi_dpi_timing_calculation(struct drm_display_mode *mode,
+				struct mdfld_dsi_dpi_timing *dpi_timing,
+				int num_lane, int bpp)
+{
+	int pclk_hsync, pclk_hfp, pclk_hbp, pclk_hactive;
+	int pclk_vsync, pclk_vfp, pclk_vbp, pclk_vactive;
+
+	pclk_hactive = mode->hdisplay;
+	pclk_hfp = mode->hsync_start - mode->hdisplay;
+	pclk_hsync = mode->hsync_end - mode->hsync_start;
+	pclk_hbp = mode->htotal - mode->hsync_end;
+
+	pclk_vactive = mode->vdisplay;
+	pclk_vfp = mode->vsync_start - mode->vdisplay;
+	pclk_vsync = mode->vsync_end - mode->vsync_start;
+	pclk_vbp = mode->vtotal - mode->vsync_end;
+
+	/*
+	 * byte clock counts were calculated by following formula
+	 * bclock_count = pclk_count * bpp / num_lane / 8
+	 */
+	dpi_timing->hsync_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_hsync, num_lane, bpp);
+	dpi_timing->hbp_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_hbp, num_lane, bpp);
+	dpi_timing->hfp_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_hfp, num_lane, bpp);
+	dpi_timing->hactive_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_hactive, num_lane, bpp);
+	dpi_timing->vsync_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_vsync, num_lane, bpp);
+	dpi_timing->vbp_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_vbp, num_lane, bpp);
+	dpi_timing->vfp_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_vfp, num_lane, bpp);
+
+	return 0;
+}
+
+void mdfld_dsi_dpi_controller_init(struct mdfld_dsi_config *dsi_config,
+								int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	int lane_count = dsi_config->lane_count;
+	struct mdfld_dsi_dpi_timing dpi_timing;
+	struct drm_display_mode *mode = dsi_config->mode;
+	u32 val;
+
+	/*un-ready device*/
+	REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 0, 0, 0);
+
+	/*init dsi adapter before kicking off*/
+	REG_WRITE(MIPI_CTRL_REG(pipe), 0x00000018);
+
+	/*enable all interrupts*/
+	REG_WRITE(MIPI_INTR_EN_REG(pipe), 0xffffffff);
+
+	/*set up func_prg*/
+	val = lane_count;
+	val |= dsi_config->channel_num << DSI_DPI_VIRT_CHANNEL_OFFSET;
+
+	switch (dsi_config->bpp) {
+	case 16:
+		val |= DSI_DPI_COLOR_FORMAT_RGB565;
+		break;
+	case 18:
+		val |= DSI_DPI_COLOR_FORMAT_RGB666;
+		break;
+	case 24:
+		val |= DSI_DPI_COLOR_FORMAT_RGB888;
+		break;
+	default:
+		DRM_ERROR("unsupported color format, bpp = %d\n",
+							dsi_config->bpp);
+	}
+	REG_WRITE(MIPI_DSI_FUNC_PRG_REG(pipe), val);
+
+	REG_WRITE(MIPI_HS_TX_TIMEOUT_REG(pipe),
+			(mode->vtotal * mode->htotal * dsi_config->bpp /
+				(8 * lane_count)) & DSI_HS_TX_TIMEOUT_MASK);
+	REG_WRITE(MIPI_LP_RX_TIMEOUT_REG(pipe),
+				0xffff & DSI_LP_RX_TIMEOUT_MASK);
+
+	/*max value: 20 clock cycles of txclkesc*/
+	REG_WRITE(MIPI_TURN_AROUND_TIMEOUT_REG(pipe),
+				0x14 & DSI_TURN_AROUND_TIMEOUT_MASK);
+
+	/*min 21 txclkesc, max: ffffh*/
+	REG_WRITE(MIPI_DEVICE_RESET_TIMER_REG(pipe),
+				0xffff & DSI_RESET_TIMER_MASK);
+
+	REG_WRITE(MIPI_DPI_RESOLUTION_REG(pipe),
+				mode->vdisplay << 16 | mode->hdisplay);
+
+	/*set DPI timing registers*/
+	mdfld_dsi_dpi_timing_calculation(mode, &dpi_timing,
+				dsi_config->lane_count, dsi_config->bpp);
+
+	REG_WRITE(MIPI_HSYNC_COUNT_REG(pipe),
+			dpi_timing.hsync_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HBP_COUNT_REG(pipe),
+			dpi_timing.hbp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HFP_COUNT_REG(pipe),
+			dpi_timing.hfp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HACTIVE_COUNT_REG(pipe),
+			dpi_timing.hactive_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VSYNC_COUNT_REG(pipe),
+			dpi_timing.vsync_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VBP_COUNT_REG(pipe),
+			dpi_timing.vbp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VFP_COUNT_REG(pipe),
+			dpi_timing.vfp_count & DSI_DPI_TIMING_MASK);
+
+	REG_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT_REG(pipe), 0x46);
+
+	/*min: 7d0 max: 4e20*/
+	REG_WRITE(MIPI_INIT_COUNT_REG(pipe), 0x000007d0);
+
+	/*set up video mode*/
+	val = dsi_config->video_mode | DSI_DPI_COMPLETE_LAST_LINE;
+	REG_WRITE(MIPI_VIDEO_MODE_FORMAT_REG(pipe), val);
+
+	REG_WRITE(MIPI_EOT_DISABLE_REG(pipe), 0x00000000);
+
+	REG_WRITE(MIPI_LP_BYTECLK_REG(pipe), 0x00000004);
+
+	/*TODO: figure out how to setup these registers*/
+	if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+		REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x2A0c6008);
+	else
+		REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x150c3408);
+
+	REG_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT_REG(pipe), (0xa << 16) | 0x14);
+
+	if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+		tc35876x_set_bridge_reset_state(dev, 0);  /*Pull High Reset */
+
+	/*set device ready*/
+	REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 1, 0, 0);
+}
+
+void mdfld_dsi_dpi_turn_on(struct mdfld_dsi_dpi_output *output, int pipe)
+{
+	struct drm_device *dev = output->dev;
+
+	/* clear special packet sent bit */
+	if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT)
+		REG_WRITE(MIPI_INTR_STAT_REG(pipe),
+					DSI_INTR_STATE_SPL_PKG_SENT);
+
+	/*send turn on package*/
+	REG_WRITE(MIPI_DPI_CONTROL_REG(pipe), DSI_DPI_CTRL_HS_TURN_ON);
+
+	/*wait for SPL_PKG_SENT interrupt*/
+	mdfld_wait_for_SPL_PKG_SENT(dev, pipe);
+
+	if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT)
+		REG_WRITE(MIPI_INTR_STAT_REG(pipe),
+					DSI_INTR_STATE_SPL_PKG_SENT);
+
+	output->panel_on = 1;
+
+	/* FIXME the following is disabled to WA the X slow start issue
+	   for TMD panel
+	if (pipe == 2)
+		dev_priv->dpi_panel_on2 = true;
+	else if (pipe == 0)
+		dev_priv->dpi_panel_on = true; */
+}
+
+static void mdfld_dsi_dpi_shut_down(struct mdfld_dsi_dpi_output *output,
+								int pipe)
+{
+	struct drm_device *dev = output->dev;
+
+	/*if output is on, or mode setting didn't happen, ignore this*/
+	if ((!output->panel_on) || output->first_boot) {
+		output->first_boot = 0;
+		return;
+	}
+
+	/* Wait for dpi fifo to empty */
+	mdfld_wait_for_DPI_CTRL_FIFO(dev, pipe);
+
+	/* Clear the special packet interrupt bit if set */
+	if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT)
+		REG_WRITE(MIPI_INTR_STAT_REG(pipe),
+					DSI_INTR_STATE_SPL_PKG_SENT);
+
+	if (REG_READ(MIPI_DPI_CONTROL_REG(pipe)) == DSI_DPI_CTRL_HS_SHUTDOWN)
+		goto shutdown_out;
+
+	REG_WRITE(MIPI_DPI_CONTROL_REG(pipe), DSI_DPI_CTRL_HS_SHUTDOWN);
+
+shutdown_out:
+	output->panel_on = 0;
+	output->first_boot = 0;
+
+	/* FIXME the following is disabled to WA the X slow start issue
+	   for TMD panel
+	if (pipe == 2)
+		dev_priv->dpi_panel_on2 = false;
+	else if (pipe == 0)
+		dev_priv->dpi_panel_on = false;	 */
+}
+
+static void mdfld_dsi_dpi_set_power(struct drm_encoder *encoder, bool on)
+{
+	struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder);
+	struct mdfld_dsi_dpi_output *dpi_output =
+				MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	int pipe = mdfld_dsi_encoder_get_pipe(dsi_encoder);
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	u32 pipeconf_reg = PIPEACONF;
+
+	if (pipe)
+		pipeconf_reg = PIPECCONF;
+
+	/*start up display island if it was shutdown*/
+	if (!gma_power_begin(dev, true))
+		return;
+
+	if (on) {
+		if (mdfld_get_panel_type(dev, pipe) == TMD_VID)
+			mdfld_dsi_dpi_turn_on(dpi_output, pipe);
+		else if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+			mdfld_dsi_configure_up(dsi_encoder, pipe);
+		else {
+			/*enable mipi port*/
+			REG_WRITE(MIPI_PORT_CONTROL(pipe),
+				REG_READ(MIPI_PORT_CONTROL(pipe)) | BIT(31));
+			REG_READ(MIPI_PORT_CONTROL(pipe));
+
+			mdfld_dsi_dpi_turn_on(dpi_output, pipe);
+			mdfld_dsi_tpo_ic_init(dsi_config, pipe);
+		}
+		dev_priv->dpi_panel_on[pipe] = true;
+	} else {
+		if (mdfld_get_panel_type(dev, pipe) == TMD_VID)
+			mdfld_dsi_dpi_shut_down(dpi_output, pipe);
+		else if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+			mdfld_dsi_configure_down(dsi_encoder, pipe);
+		else {
+			mdfld_dsi_dpi_shut_down(dpi_output, pipe);
+
+			/*disable mipi port*/
+			REG_WRITE(MIPI_PORT_CONTROL(pipe),
+				REG_READ(MIPI_PORT_CONTROL(pipe)) & ~BIT(31));
+			REG_READ(MIPI_PORT_CONTROL(pipe));
+		}
+		dev_priv->dpi_panel_on[pipe] = false;
+	}
+	gma_power_end(dev);
+}
+
+void mdfld_dsi_dpi_dpms(struct drm_encoder *encoder, int mode)
+{
+	mdfld_dsi_dpi_set_power(encoder, mode == DRM_MODE_DPMS_ON);
+}
+
+bool mdfld_dsi_dpi_mode_fixup(struct drm_encoder *encoder,
+				     struct drm_display_mode *mode,
+				     struct drm_display_mode *adjusted_mode)
+{
+	struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	struct drm_display_mode *fixed_mode = dsi_config->fixed_mode;
+
+	if (fixed_mode) {
+		adjusted_mode->hdisplay = fixed_mode->hdisplay;
+		adjusted_mode->hsync_start = fixed_mode->hsync_start;
+		adjusted_mode->hsync_end = fixed_mode->hsync_end;
+		adjusted_mode->htotal = fixed_mode->htotal;
+		adjusted_mode->vdisplay = fixed_mode->vdisplay;
+		adjusted_mode->vsync_start = fixed_mode->vsync_start;
+		adjusted_mode->vsync_end = fixed_mode->vsync_end;
+		adjusted_mode->vtotal = fixed_mode->vtotal;
+		adjusted_mode->clock = fixed_mode->clock;
+		drm_mode_set_crtcinfo(adjusted_mode, CRTC_INTERLACE_HALVE_V);
+	}
+	return true;
+}
+
+void mdfld_dsi_dpi_prepare(struct drm_encoder *encoder)
+{
+	mdfld_dsi_dpi_set_power(encoder, false);
+}
+
+void mdfld_dsi_dpi_commit(struct drm_encoder *encoder)
+{
+	mdfld_dsi_dpi_set_power(encoder, true);
+}
+
+/* For TC35876X */
+/* This functionality was implemented in FW in iCDK */
+/* But removed in DV0 and later. So need to add here. */
+static void mipi_set_properties(struct mdfld_dsi_config *dsi_config, int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+
+	REG_WRITE(MIPI_CTRL_REG(pipe), 0x00000018);
+	REG_WRITE(MIPI_INTR_EN_REG(pipe), 0xffffffff);
+	REG_WRITE(MIPI_HS_TX_TIMEOUT_REG(pipe), 0xffffff);
+	REG_WRITE(MIPI_LP_RX_TIMEOUT_REG(pipe), 0xffffff);
+	REG_WRITE(MIPI_TURN_AROUND_TIMEOUT_REG(pipe), 0x14);
+	REG_WRITE(MIPI_DEVICE_RESET_TIMER_REG(pipe), 0xff);
+	REG_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT_REG(pipe), 0x25);
+	REG_WRITE(MIPI_INIT_COUNT_REG(pipe), 0xf0);
+	REG_WRITE(MIPI_EOT_DISABLE_REG(pipe), 0x00000000);
+	REG_WRITE(MIPI_LP_BYTECLK_REG(pipe), 0x00000004);
+	REG_WRITE(MIPI_DBI_BW_CTRL_REG(pipe), 0x00000820);
+	REG_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT_REG(pipe), (0xa << 16) | 0x14);
+}
+
+static void mdfld_mipi_set_video_timing(struct mdfld_dsi_config *dsi_config,
+					int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	struct mdfld_dsi_dpi_timing dpi_timing;
+	struct drm_display_mode *mode = dsi_config->mode;
+
+	mdfld_dsi_dpi_timing_calculation(mode, &dpi_timing,
+					dsi_config->lane_count,
+					dsi_config->bpp);
+
+	REG_WRITE(MIPI_DPI_RESOLUTION_REG(pipe),
+		mode->vdisplay << 16 | mode->hdisplay);
+	REG_WRITE(MIPI_HSYNC_COUNT_REG(pipe),
+		dpi_timing.hsync_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HBP_COUNT_REG(pipe),
+		dpi_timing.hbp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HFP_COUNT_REG(pipe),
+		dpi_timing.hfp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HACTIVE_COUNT_REG(pipe),
+		dpi_timing.hactive_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VSYNC_COUNT_REG(pipe),
+		dpi_timing.vsync_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VBP_COUNT_REG(pipe),
+		dpi_timing.vbp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VFP_COUNT_REG(pipe),
+		dpi_timing.vfp_count & DSI_DPI_TIMING_MASK);
+}
+
+static void mdfld_mipi_config(struct mdfld_dsi_config *dsi_config, int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	int lane_count = dsi_config->lane_count;
+
+	if (pipe) {
+		REG_WRITE(MIPI_PORT_CONTROL(0), 0x00000002);
+		REG_WRITE(MIPI_PORT_CONTROL(2), 0x80000000);
+	} else {
+		REG_WRITE(MIPI_PORT_CONTROL(0), 0x80010000);
+		REG_WRITE(MIPI_PORT_CONTROL(2), 0x00);
+	}
+
+	REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x150A600F);
+	REG_WRITE(MIPI_VIDEO_MODE_FORMAT_REG(pipe), 0x0000000F);
+
+	/* lane_count = 3 */
+	REG_WRITE(MIPI_DSI_FUNC_PRG_REG(pipe), 0x00000200 | lane_count);
+
+	mdfld_mipi_set_video_timing(dsi_config, pipe);
+}
+
+static void mdfld_set_pipe_timing(struct mdfld_dsi_config *dsi_config, int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_display_mode *mode = dsi_config->mode;
+
+	REG_WRITE(HTOTAL_A, ((mode->htotal - 1) << 16) | (mode->hdisplay - 1));
+	REG_WRITE(HBLANK_A, ((mode->htotal - 1) << 16) | (mode->hdisplay - 1));
+	REG_WRITE(HSYNC_A,
+		((mode->hsync_end - 1) << 16) | (mode->hsync_start - 1));
+
+	REG_WRITE(VTOTAL_A, ((mode->vtotal - 1) << 16) | (mode->vdisplay - 1));
+	REG_WRITE(VBLANK_A, ((mode->vtotal - 1) << 16) | (mode->vdisplay - 1));
+	REG_WRITE(VSYNC_A,
+		((mode->vsync_end - 1) << 16) | (mode->vsync_start - 1));
+
+	REG_WRITE(PIPEASRC,
+		((mode->hdisplay - 1) << 16) | (mode->vdisplay - 1));
+}
+/* End for TC35876X */
+
+void mdfld_dsi_dpi_mode_set(struct drm_encoder *encoder,
+				   struct drm_display_mode *mode,
+				   struct drm_display_mode *adjusted_mode)
+{
+	struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder);
+	struct mdfld_dsi_dpi_output *dpi_output =
+					MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	int pipe = mdfld_dsi_encoder_get_pipe(dsi_encoder);
+
+	u32 pipeconf_reg = PIPEACONF;
+	u32 dspcntr_reg = DSPACNTR;
+
+	u32 pipeconf = dev_priv->pipeconf[pipe];
+	u32 dspcntr = dev_priv->dspcntr[pipe];
+	u32 mipi = MIPI_PORT_EN | PASS_FROM_SPHY_TO_AFE | SEL_FLOPPED_HSTX;
+
+	if (pipe) {
+		pipeconf_reg = PIPECCONF;
+		dspcntr_reg = DSPCCNTR;
+	} else {
+		if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+			mipi &= (~0x03); /* Use all four lanes */
+		else
+			mipi |= 2;
+	}
+
+	/*start up display island if it was shutdown*/
+	if (!gma_power_begin(dev, true))
+		return;
+
+	if (mdfld_get_panel_type(dev, pipe) == TC35876X) {
+		/*
+		 * The following logic is required to reset the bridge and
+		 * configure. This also starts the DSI clock at 200MHz.
+		 */
+		tc35876x_set_bridge_reset_state(dev, 0);  /*Pull High Reset */
+		tc35876x_toshiba_bridge_panel_on(dev);
+		udelay(100);
+		/* Now start the DSI clock */
+		REG_WRITE(MRST_DPLL_A, 0x00);
+		REG_WRITE(MRST_FPA0, 0xC1);
+		REG_WRITE(MRST_DPLL_A, 0x00800000);
+		udelay(500);
+		REG_WRITE(MRST_DPLL_A, 0x80800000);
+
+		if (REG_BIT_WAIT(pipeconf_reg, 1, 29))
+			dev_err(&dev->pdev->dev, "%s: DSI PLL lock timeout\n",
+				__func__);
+
+		REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x2A0c6008);
+
+		mipi_set_properties(dsi_config, pipe);
+		mdfld_mipi_config(dsi_config, pipe);
+		mdfld_set_pipe_timing(dsi_config, pipe);
+
+		REG_WRITE(DSPABASE, 0x00);
+		REG_WRITE(DSPASTRIDE, (mode->hdisplay * 4));
+		REG_WRITE(DSPASIZE,
+			((mode->vdisplay - 1) << 16) | (mode->hdisplay - 1));
+
+		REG_WRITE(DSPACNTR, 0x98000000);
+		REG_WRITE(DSPASURF, 0x00);
+
+		REG_WRITE(VGACNTRL, 0x80000000);
+		REG_WRITE(DEVICE_READY_REG, 0x00000001);
+
+		REG_WRITE(MIPI_PORT_CONTROL(pipe), 0x80810000);
+	} else {
+		/*set up mipi port FIXME: do at init time */
+		REG_WRITE(MIPI_PORT_CONTROL(pipe), mipi);
+	}
+	REG_READ(MIPI_PORT_CONTROL(pipe));
+
+	if (mdfld_get_panel_type(dev, pipe) == TMD_VID) {
+		/* NOP */
+	} else if (mdfld_get_panel_type(dev, pipe) == TC35876X) {
+		/* set up DSI controller DPI interface */
+		mdfld_dsi_dpi_controller_init(dsi_config, pipe);
+
+		/* Configure MIPI Bridge and Panel */
+		tc35876x_configure_lvds_bridge(dev);
+		dev_priv->dpi_panel_on[pipe] = true;
+	} else {
+		/*turn on DPI interface*/
+		mdfld_dsi_dpi_turn_on(dpi_output, pipe);
+	}
+
+	/*set up pipe*/
+	REG_WRITE(pipeconf_reg, pipeconf);
+	REG_READ(pipeconf_reg);
+
+	/*set up display plane*/
+	REG_WRITE(dspcntr_reg, dspcntr);
+	REG_READ(dspcntr_reg);
+
+	msleep(20); /* FIXME: this should wait for vblank */
+
+	if (mdfld_get_panel_type(dev, pipe) == TMD_VID) {
+		/* NOP */
+	} else if (mdfld_get_panel_type(dev, pipe) == TC35876X) {
+		mdfld_dsi_dpi_turn_on(dpi_output, pipe);
+	} else {
+		/* init driver ic */
+		mdfld_dsi_tpo_ic_init(dsi_config, pipe);
+		/*init backlight*/
+		mdfld_dsi_brightness_init(dsi_config, pipe);
+	}
+
+	gma_power_end(dev);
+}
+
+/*
+ * Init DSI DPI encoder.
+ * Allocate an mdfld_dsi_encoder and attach it to given @dsi_connector
+ * return pointer of newly allocated DPI encoder, NULL on error
+ */
+struct mdfld_dsi_encoder *mdfld_dsi_dpi_init(struct drm_device *dev,
+				struct mdfld_dsi_connector *dsi_connector,
+				const struct panel_funcs *p_funcs)
+{
+	struct mdfld_dsi_dpi_output *dpi_output = NULL;
+	struct mdfld_dsi_config *dsi_config;
+	struct drm_connector *connector = NULL;
+	struct drm_encoder *encoder = NULL;
+	struct drm_display_mode *fixed_mode = NULL;
+	int pipe;
+	u32 data;
+	int ret;
+
+	pipe = dsi_connector->pipe;
+
+	if (mdfld_get_panel_type(dev, pipe) != TC35876X) {
+		dsi_config = mdfld_dsi_get_config(dsi_connector);
+
+		/* panel hard-reset */
+		if (p_funcs->reset) {
+			ret = p_funcs->reset(pipe);
+			if (ret) {
+				DRM_ERROR("Panel %d hard-reset failed\n", pipe);
+				return NULL;
+			}
+		}
+
+		/* panel drvIC init */
+		if (p_funcs->drv_ic_init)
+			p_funcs->drv_ic_init(dsi_config, pipe);
+
+		/* panel power mode detect */
+		ret = mdfld_dsi_get_power_mode(dsi_config, &data, false);
+		if (ret) {
+			DRM_ERROR("Panel %d get power mode failed\n", pipe);
+			dsi_connector->status = connector_status_disconnected;
+		} else {
+			DRM_INFO("pipe %d power mode 0x%x\n", pipe, data);
+			dsi_connector->status = connector_status_connected;
+		}
+	}
+
+	dpi_output = kzalloc(sizeof(struct mdfld_dsi_dpi_output), GFP_KERNEL);
+	if (!dpi_output) {
+		DRM_ERROR("No memory\n");
+		return NULL;
+	}
+
+	if (dsi_connector->pipe)
+		dpi_output->panel_on = 0;
+	else
+		dpi_output->panel_on = 0;
+
+	dpi_output->dev = dev;
+	if (mdfld_get_panel_type(dev, pipe) != TC35876X)
+		dpi_output->p_funcs = p_funcs;
+	dpi_output->first_boot = 1;
+
+	/*get fixed mode*/
+	dsi_config = mdfld_dsi_get_config(dsi_connector);
+	fixed_mode = dsi_config->fixed_mode;
+
+	/*create drm encoder object*/
+	connector = &dsi_connector->base.base;
+	encoder = &dpi_output->base.base.base;
+	drm_encoder_init(dev,
+			encoder,
+			p_funcs->encoder_funcs,
+			DRM_MODE_ENCODER_LVDS);
+	drm_encoder_helper_add(encoder,
+				p_funcs->encoder_helper_funcs);
+
+	/*attach to given connector*/
+	drm_mode_connector_attach_encoder(connector, encoder);
+
+	/*set possible crtcs and clones*/
+	if (dsi_connector->pipe) {
+		encoder->possible_crtcs = (1 << 2);
+		encoder->possible_clones = (1 << 1);
+	} else {
+		encoder->possible_crtcs = (1 << 0);
+		encoder->possible_clones = (1 << 0);
+	}
+
+	dsi_connector->base.encoder = &dpi_output->base.base;
+
+	return &dpi_output->base;
+}