diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media')
13 files changed, 357 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt new file mode 100644 index 000000000000..21ffb5ed8183 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt @@ -0,0 +1,95 @@ +* Analog Devices ADV748X video decoder with HDMI receiver + +The ADV7481 and ADV7482 are multi format video decoders with an integrated +HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB +from three input sources HDMI, analog and TTL. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7481" for the ADV7481 + - "adi,adv7482" for the ADV7482 + + - reg: I2C slave address + +Optional Properties: + + - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or + "intrq3". All interrupts are optional. The "intrq3" interrupt + is only available on the adv7481 + - interrupts: Specify the interrupt lines for the ADV748x + +The device node must contain one 'port' child node per device input and output +port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows. + + Name Type Port + --------------------------------------- + AIN0 sink 0 + AIN1 sink 1 + AIN2 sink 2 + AIN3 sink 3 + AIN4 sink 4 + AIN5 sink 5 + AIN6 sink 6 + AIN7 sink 7 + HDMI sink 8 + TTL sink 9 + TXA source 10 + TXB source 11 + +The digital output port nodes must contain at least one endpoint. + +Ports are optional if they are not connected to anything at the hardware level. + +Example: + + video-receiver@70 { + compatible = "adi,adv7482"; + reg = <0x70>; + + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&gpio6>; + interrupt-names = "intrq1", "intrq2"; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, + <31 IRQ_TYPE_LEVEL_LOW>; + + port@7 { + reg = <7>; + + adv7482_ain7: endpoint { + remote-endpoint = <&cvbs_in>; + }; + }; + + port@8 { + reg = <8>; + + adv7482_hdmi: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + + port@10 { + reg = <10>; + + adv7482_txa: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + + port@11 { + reg = <11>; + + adv7482_txb: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&csi20_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt new file mode 100644 index 000000000000..b88dcdd41def --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt @@ -0,0 +1,9 @@ +Dongwoon Anatech DW9714 camera voice coil lens driver + +DW9174 is a 10-bit DAC with current sink capability. It is intended +for driving voice coil lenses in camera modules. + +Mandatory properties: + +- compatible: "dongwoon,dw9714" +- reg: I²C slave address diff --git a/Documentation/devicetree/bindings/media/meson-ao-cec.txt b/Documentation/devicetree/bindings/media/meson-ao-cec.txt new file mode 100644 index 000000000000..8671bdb08080 --- /dev/null +++ b/Documentation/devicetree/bindings/media/meson-ao-cec.txt @@ -0,0 +1,28 @@ +* Amlogic Meson AO-CEC driver + +The Amlogic Meson AO-CEC module is present is Amlogic SoCs and its purpose is +to handle communication between HDMI connected devices over the CEC bus. + +Required properties: + - compatible : value should be following + "amlogic,meson-gx-ao-cec" + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : AO-CEC interrupt number to the CPU. + - clocks : from common clock binding: handle to AO-CEC clock. + - clock-names : from common clock binding: must contain "core", + corresponding to entry in the clocks property. + - hdmi-phandle: phandle to the HDMI controller + +Example: + +cec_AO: cec@100 { + compatible = "amlogic,meson-gx-ao-cec"; + reg = <0x0 0x00100 0x0 0x14>; + interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc_AO CLKID_AO_CEC_32K>; + clock-names = "core"; + hdmi-phandle = <&hdmi_tx>; +}; diff --git a/Documentation/devicetree/bindings/media/mtk-cir.txt b/Documentation/devicetree/bindings/media/mtk-cir.txt index 2be2005577d6..5e18087ce11f 100644 --- a/Documentation/devicetree/bindings/media/mtk-cir.txt +++ b/Documentation/devicetree/bindings/media/mtk-cir.txt @@ -2,10 +2,14 @@ Device-Tree bindings for Mediatek consumer IR controller found in Mediatek SoC family Required properties: -- compatible : "mediatek,mt7623-cir" +- compatible : Should be + "mediatek,mt7623-cir": for MT7623 SoC + "mediatek,mt7622-cir": for MT7622 SoC - clocks : list of clock specifiers, corresponding to entries in clock-names property; -- clock-names : should contain "clk" entries; +- clock-names : should contain + - "clk" entries: for MT7623 SoC + - "clk", "bus" entries: for MT7622 SoC - interrupts : should contain IR IRQ number; - reg : should contain IO map address for IR. diff --git a/Documentation/devicetree/bindings/media/pxa-camera.txt b/Documentation/devicetree/bindings/media/pxa-camera.txt index 11f5b5d51af8..bc03ec096269 100644 --- a/Documentation/devicetree/bindings/media/pxa-camera.txt +++ b/Documentation/devicetree/bindings/media/pxa-camera.txt @@ -24,7 +24,6 @@ Example: clock-frequency = <50000000>; clock-output-names = "qci_mclk"; - status = "okay"; port { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/media/qcom,camss.txt b/Documentation/devicetree/bindings/media/qcom,camss.txt new file mode 100644 index 000000000000..cadecebc73f7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,camss.txt @@ -0,0 +1,197 @@ +Qualcomm Camera Subsystem + +* Properties + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Should contain: + - "qcom,msm8916-camss" +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register ranges as listed in the reg-names property. +- reg-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries: + - "csiphy0" + - "csiphy0_clk_mux" + - "csiphy1" + - "csiphy1_clk_mux" + - "csid0" + - "csid1" + - "ispif" + - "csi_clk_mux" + - "vfe0" +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Interrupts as listed in the interrupt-names property. +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries: + - "csiphy0" + - "csiphy1" + - "csid0" + - "csid1" + - "ispif" + - "vfe0" +- power-domains: + Usage: required + Value type: <prop-encoded-array> + Definition: A phandle and power domain specifier pairs to the + power domain which is responsible for collapsing + and restoring power to the peripheral. +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and clock specifier pairs as listed + in clock-names property. +- clock-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries: + - "camss_top_ahb" + - "ispif_ahb" + - "csiphy0_timer" + - "csiphy1_timer" + - "csi0_ahb" + - "csi0" + - "csi0_phy" + - "csi0_pix" + - "csi0_rdi" + - "csi1_ahb" + - "csi1" + - "csi1_phy" + - "csi1_pix" + - "csi1_rdi" + - "camss_ahb" + - "camss_vfe_vfe" + - "camss_csi_vfe" + - "iface" + - "bus" +- vdda-supply: + Usage: required + Value type: <phandle> + Definition: A phandle to voltage supply for CSI2. +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. + +* Nodes + +- ports: + Usage: required + Definition: As described in video-interfaces.txt in same directory. + Properties: + - reg: + Usage: required + Value type: <u32> + Definition: Selects CSI2 PHY interface - PHY0 or PHY1. + Endpoint node properties: + - clock-lanes: + Usage: required + Value type: <u32> + Definition: The physical clock lane index. The value + must always be <1> as the physical clock + lane is lane 1. + - data-lanes: + Usage: required + Value type: <prop-encoded-array> + Definition: An array of physical data lanes indexes. + Position of an entry determines the logical + lane number, while the value of an entry + indicates physical lane index. Lane swapping + is supported. + +* An Example + + camss: camss@1b00000 { + compatible = "qcom,msm8916-camss"; + reg = <0x1b0ac00 0x200>, + <0x1b00030 0x4>, + <0x1b0b000 0x200>, + <0x1b00038 0x4>, + <0x1b08000 0x100>, + <0x1b08400 0x100>, + <0x1b0a000 0x500>, + <0x1b00020 0x10>, + <0x1b10000 0x1000>; + reg-names = "csiphy0", + "csiphy0_clk_mux", + "csiphy1", + "csiphy1_clk_mux", + "csid0", + "csid1", + "ispif", + "csi_clk_mux", + "vfe0"; + interrupts = <GIC_SPI 78 0>, + <GIC_SPI 79 0>, + <GIC_SPI 51 0>, + <GIC_SPI 52 0>, + <GIC_SPI 55 0>, + <GIC_SPI 57 0>; + interrupt-names = "csiphy0", + "csiphy1", + "csid0", + "csid1", + "ispif", + "vfe0"; + power-domains = <&gcc VFE_GDSC>; + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, + <&gcc GCC_CAMSS_ISPIF_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI0_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0_CLK>, + <&gcc GCC_CAMSS_CSI0PHY_CLK>, + <&gcc GCC_CAMSS_CSI0PIX_CLK>, + <&gcc GCC_CAMSS_CSI0RDI_CLK>, + <&gcc GCC_CAMSS_CSI1_AHB_CLK>, + <&gcc GCC_CAMSS_CSI1_CLK>, + <&gcc GCC_CAMSS_CSI1PHY_CLK>, + <&gcc GCC_CAMSS_CSI1PIX_CLK>, + <&gcc GCC_CAMSS_CSI1RDI_CLK>, + <&gcc GCC_CAMSS_AHB_CLK>, + <&gcc GCC_CAMSS_VFE0_CLK>, + <&gcc GCC_CAMSS_CSI_VFE0_CLK>, + <&gcc GCC_CAMSS_VFE_AHB_CLK>, + <&gcc GCC_CAMSS_VFE_AXI_CLK>; + clock-names = "camss_top_ahb", + "ispif_ahb", + "csiphy0_timer", + "csiphy1_timer", + "csi0_ahb", + "csi0", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1_ahb", + "csi1", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "camss_ahb", + "camss_vfe_vfe", + "camss_csi_vfe", + "iface", + "bus"; + vdda-supply = <&pm8916_l2>; + iommus = <&apps_iommu 3>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + csiphy0_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&ov5645_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt index 39516b94c28f..0d8974aa8b38 100644 --- a/Documentation/devicetree/bindings/media/renesas,drif.txt +++ b/Documentation/devicetree/bindings/media/renesas,drif.txt @@ -40,6 +40,7 @@ To summarize, Required properties of an internal channel: ------------------------------------------- - compatible: "renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC. + "renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 SoC. "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device. When compatible with the generic version, nodes must list the diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt index 1b1a10ba48ce..6f3756da900f 100644 --- a/Documentation/devicetree/bindings/media/s5p-cec.txt +++ b/Documentation/devicetree/bindings/media/s5p-cec.txt @@ -33,5 +33,4 @@ hdmicec: cec@100B0000 { hdmi-phandle = <&hdmi>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_cec>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/media/samsung-fimc.txt b/Documentation/devicetree/bindings/media/samsung-fimc.txt index 922d6f8e74be..e4e15d8d7521 100644 --- a/Documentation/devicetree/bindings/media/samsung-fimc.txt +++ b/Documentation/devicetree/bindings/media/samsung-fimc.txt @@ -166,7 +166,6 @@ Example: clock-output-names = "cam_a_clkout", "cam_b_clkout"; pinctrl-names = "default"; pinctrl-0 = <&cam_port_a_clk_active>; - status = "okay"; #address-cells = <1>; #size-cells = <1>; @@ -189,7 +188,6 @@ Example: compatible = "samsung,exynos4210-fimc"; reg = <0x11800000 0x1000>; interrupts = <0 85 0>; - status = "okay"; }; csis_0: csis@11880000 { diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt index cc51b1fd6e0c..6af3fc210ecc 100644 --- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt +++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt @@ -52,7 +52,6 @@ Example: c8sectpfe@08a20000 { compatible = "st,stih407-c8sectpfe"; - status = "okay"; reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>; reg-names = "stfe", "stfe-ram"; interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>; diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt index df7182a63e59..e47c7ccc57f1 100644 --- a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt @@ -59,7 +59,6 @@ I2C-connected TVP5147 decoder: tvp5147@5d { compatible = "ti,tvp5147"; reg = <0x5d>; - status = "okay"; port { composite_in: endpoint { diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index 9cd2a369125d..852041a7480c 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -76,6 +76,11 @@ Optional endpoint properties mode horizontal and vertical synchronization signals are provided to the slave device (data source) by the master device (data sink). In the master mode the data source device is also the source of the synchronization signals. +- bus-type: data bus type. Possible values are: + 0 - autodetect based on other properties (MIPI CSI-2 D-PHY, parallel or Bt656) + 1 - MIPI CSI-2 C-PHY + 2 - MIPI CSI1 + 3 - CCP2 - bus-width: number of data lines actively used, valid for the parallel busses. - data-shift: on the parallel data busses, if bus-width is used to specify the number of data lines, data-shift can be used to specify which data lines are @@ -112,7 +117,8 @@ Optional endpoint properties should be the combined length of data-lanes and clock-lanes properties. If the lane-polarities property is omitted, the value must be interpreted as 0 (normal). This property is valid for serial busses only. - +- strobe: Whether the clock signal is used as clock (0) or strobe (1). Used + with CCP2, for instance. Example ------- diff --git a/Documentation/devicetree/bindings/media/zx-irdec.txt b/Documentation/devicetree/bindings/media/zx-irdec.txt new file mode 100644 index 000000000000..295b9fab593e --- /dev/null +++ b/Documentation/devicetree/bindings/media/zx-irdec.txt @@ -0,0 +1,14 @@ +IR Decoder (IRDEC) on ZTE ZX family SoCs + +Required properties: + - compatible: Should be "zte,zx296718-irdec". + - reg: Physical base address and length of IRDEC registers. + - interrupts: Interrupt number of IRDEC. + +Exmaples: + + irdec: ir-decoder@111000 { + compatible = "zte,zx296718-irdec"; + reg = <0x111000 0x1000>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + }; |