summaryrefslogtreecommitdiff
path: root/drivers/spi/spi-bcm2835.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/spi/spi-bcm2835.c')
-rw-r--r--drivers/spi/spi-bcm2835.c391
1 files changed, 253 insertions, 138 deletions
diff --git a/drivers/spi/spi-bcm2835.c b/drivers/spi/spi-bcm2835.c
index 419a782ab6d5..f63864a893c5 100644
--- a/drivers/spi/spi-bcm2835.c
+++ b/drivers/spi/spi-bcm2835.c
@@ -3,6 +3,7 @@
*
* Copyright (C) 2012 Chris Boot
* Copyright (C) 2013 Stephen Warren
+ * Copyright (C) 2015 Martin Sperl
*
* This driver is inspired by:
* spi-ath79.c, Copyright (C) 2009-2011 Gabor Juhos <juhosg@openwrt.org>
@@ -29,6 +30,7 @@
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
#include <linux/of_device.h>
#include <linux/spi/spi.h>
@@ -66,8 +68,10 @@
#define BCM2835_SPI_CS_CS_10 0x00000002
#define BCM2835_SPI_CS_CS_01 0x00000001
-#define BCM2835_SPI_TIMEOUT_MS 30000
-#define BCM2835_SPI_MODE_BITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_NO_CS)
+#define BCM2835_SPI_POLLING_LIMIT_US 30
+#define BCM2835_SPI_TIMEOUT_MS 30000
+#define BCM2835_SPI_MODE_BITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
+ | SPI_NO_CS | SPI_3WIRE)
#define DRV_NAME "spi-bcm2835"
@@ -75,10 +79,10 @@ struct bcm2835_spi {
void __iomem *regs;
struct clk *clk;
int irq;
- struct completion done;
const u8 *tx_buf;
u8 *rx_buf;
- int len;
+ int tx_len;
+ int rx_len;
};
static inline u32 bcm2835_rd(struct bcm2835_spi *bs, unsigned reg)
@@ -91,205 +95,315 @@ static inline void bcm2835_wr(struct bcm2835_spi *bs, unsigned reg, u32 val)
writel(val, bs->regs + reg);
}
-static inline void bcm2835_rd_fifo(struct bcm2835_spi *bs, int len)
+static inline void bcm2835_rd_fifo(struct bcm2835_spi *bs)
{
u8 byte;
- while (len--) {
+ while ((bs->rx_len) &&
+ (bcm2835_rd(bs, BCM2835_SPI_CS) & BCM2835_SPI_CS_RXD)) {
byte = bcm2835_rd(bs, BCM2835_SPI_FIFO);
if (bs->rx_buf)
*bs->rx_buf++ = byte;
+ bs->rx_len--;
}
}
-static inline void bcm2835_wr_fifo(struct bcm2835_spi *bs, int len)
+static inline void bcm2835_wr_fifo(struct bcm2835_spi *bs)
{
u8 byte;
- if (len > bs->len)
- len = bs->len;
-
- while (len--) {
+ while ((bs->tx_len) &&
+ (bcm2835_rd(bs, BCM2835_SPI_CS) & BCM2835_SPI_CS_TXD)) {
byte = bs->tx_buf ? *bs->tx_buf++ : 0;
bcm2835_wr(bs, BCM2835_SPI_FIFO, byte);
- bs->len--;
+ bs->tx_len--;
}
}
+static void bcm2835_spi_reset_hw(struct spi_master *master)
+{
+ struct bcm2835_spi *bs = spi_master_get_devdata(master);
+ u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+
+ /* Disable SPI interrupts and transfer */
+ cs &= ~(BCM2835_SPI_CS_INTR |
+ BCM2835_SPI_CS_INTD |
+ BCM2835_SPI_CS_TA);
+ /* and reset RX/TX FIFOS */
+ cs |= BCM2835_SPI_CS_CLEAR_RX | BCM2835_SPI_CS_CLEAR_TX;
+
+ /* and reset the SPI_HW */
+ bcm2835_wr(bs, BCM2835_SPI_CS, cs);
+}
+
static irqreturn_t bcm2835_spi_interrupt(int irq, void *dev_id)
{
struct spi_master *master = dev_id;
struct bcm2835_spi *bs = spi_master_get_devdata(master);
- u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
- /*
- * RXR - RX needs Reading. This means 12 (or more) bytes have been
- * transmitted and hence 12 (or more) bytes have been received.
- *
- * The FIFO is 16-bytes deep. We check for this interrupt to keep the
- * FIFO full; we have a 4-byte-time buffer for IRQ latency. We check
- * this before DONE (TX empty) just in case we delayed processing this
- * interrupt for some reason.
- *
- * We only check for this case if we have more bytes to TX; at the end
- * of the transfer, we ignore this pipelining optimization, and let
- * bcm2835_spi_finish_transfer() drain the RX FIFO.
+ /* Read as many bytes as possible from FIFO */
+ bcm2835_rd_fifo(bs);
+ /* Write as many bytes as possible to FIFO */
+ bcm2835_wr_fifo(bs);
+
+ /* based on flags decide if we can finish the transfer */
+ if (bcm2835_rd(bs, BCM2835_SPI_CS) & BCM2835_SPI_CS_DONE) {
+ /* Transfer complete - reset SPI HW */
+ bcm2835_spi_reset_hw(master);
+ /* wake up the framework */
+ complete(&master->xfer_completion);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int bcm2835_spi_transfer_one_poll(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *tfr,
+ u32 cs,
+ unsigned long xfer_time_us)
+{
+ struct bcm2835_spi *bs = spi_master_get_devdata(master);
+ unsigned long timeout = jiffies +
+ max(4 * xfer_time_us * HZ / 1000000, 2uL);
+
+ /* enable HW block without interrupts */
+ bcm2835_wr(bs, BCM2835_SPI_CS, cs | BCM2835_SPI_CS_TA);
+
+ /* set timeout to 4x the expected time, or 2 jiffies */
+ /* loop until finished the transfer */
+ while (bs->rx_len) {
+ /* read from fifo as much as possible */
+ bcm2835_rd_fifo(bs);
+ /* fill in tx fifo as much as possible */
+ bcm2835_wr_fifo(bs);
+ /* if we still expect some data after the read,
+ * check for a possible timeout
+ */
+ if (bs->rx_len && time_after(jiffies, timeout)) {
+ /* Transfer complete - reset SPI HW */
+ bcm2835_spi_reset_hw(master);
+ /* and return timeout */
+ return -ETIMEDOUT;
+ }
+ }
+
+ /* Transfer complete - reset SPI HW */
+ bcm2835_spi_reset_hw(master);
+ /* and return without waiting for completion */
+ return 0;
+}
+
+static int bcm2835_spi_transfer_one_irq(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *tfr,
+ u32 cs)
+{
+ struct bcm2835_spi *bs = spi_master_get_devdata(master);
+
+ /* fill in fifo if we have gpio-cs
+ * note that there have been rare events where the native-CS
+ * flapped for <1us which may change the behaviour
+ * with gpio-cs this does not happen, so it is implemented
+ * only for this case
*/
- if (bs->len && (cs & BCM2835_SPI_CS_RXR)) {
- /* Read 12 bytes of data */
- bcm2835_rd_fifo(bs, 12);
-
- /* Write up to 12 bytes */
- bcm2835_wr_fifo(bs, 12);
-
- /*
- * We must have written something to the TX FIFO due to the
- * bs->len check above, so cannot be DONE. Hence, return
- * early. Note that DONE could also be set if we serviced an
- * RXR interrupt really late.
+ if (gpio_is_valid(spi->cs_gpio)) {
+ /* enable HW block, but without interrupts enabled
+ * this would triggern an immediate interrupt
*/
- return IRQ_HANDLED;
+ bcm2835_wr(bs, BCM2835_SPI_CS,
+ cs | BCM2835_SPI_CS_TA);
+ /* fill in tx fifo as much as possible */
+ bcm2835_wr_fifo(bs);
}
/*
- * DONE - TX empty. This occurs when we first enable the transfer
- * since we do not pre-fill the TX FIFO. At any other time, given that
- * we refill the TX FIFO above based on RXR, and hence ignore DONE if
- * RXR is set, DONE really does mean end-of-transfer.
+ * Enable the HW block. This will immediately trigger a DONE (TX
+ * empty) interrupt, upon which we will fill the TX FIFO with the
+ * first TX bytes. Pre-filling the TX FIFO here to avoid the
+ * interrupt doesn't work:-(
*/
- if (cs & BCM2835_SPI_CS_DONE) {
- if (bs->len) { /* First interrupt in a transfer */
- bcm2835_wr_fifo(bs, 16);
- } else { /* Transfer complete */
- /* Disable SPI interrupts */
- cs &= ~(BCM2835_SPI_CS_INTR | BCM2835_SPI_CS_INTD);
- bcm2835_wr(bs, BCM2835_SPI_CS, cs);
-
- /*
- * Wake up bcm2835_spi_transfer_one(), which will call
- * bcm2835_spi_finish_transfer(), to drain the RX FIFO.
- */
- complete(&bs->done);
- }
-
- return IRQ_HANDLED;
- }
+ cs |= BCM2835_SPI_CS_INTR | BCM2835_SPI_CS_INTD | BCM2835_SPI_CS_TA;
+ bcm2835_wr(bs, BCM2835_SPI_CS, cs);
- return IRQ_NONE;
+ /* signal that we need to wait for completion */
+ return 1;
}
-static int bcm2835_spi_start_transfer(struct spi_device *spi,
- struct spi_transfer *tfr)
+static int bcm2835_spi_transfer_one(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *tfr)
{
- struct bcm2835_spi *bs = spi_master_get_devdata(spi->master);
+ struct bcm2835_spi *bs = spi_master_get_devdata(master);
unsigned long spi_hz, clk_hz, cdiv;
- u32 cs = BCM2835_SPI_CS_INTR | BCM2835_SPI_CS_INTD | BCM2835_SPI_CS_TA;
+ unsigned long spi_used_hz, xfer_time_us;
+ u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+ /* set clock */
spi_hz = tfr->speed_hz;
clk_hz = clk_get_rate(bs->clk);
if (spi_hz >= clk_hz / 2) {
cdiv = 2; /* clk_hz/2 is the fastest we can go */
} else if (spi_hz) {
- /* CDIV must be a power of two */
- cdiv = roundup_pow_of_two(DIV_ROUND_UP(clk_hz, spi_hz));
+ /* CDIV must be a multiple of two */
+ cdiv = DIV_ROUND_UP(clk_hz, spi_hz);
+ cdiv += (cdiv % 2);
if (cdiv >= 65536)
cdiv = 0; /* 0 is the slowest we can go */
- } else
+ } else {
cdiv = 0; /* 0 is the slowest we can go */
+ }
+ spi_used_hz = cdiv ? (clk_hz / cdiv) : (clk_hz / 65536);
+ bcm2835_wr(bs, BCM2835_SPI_CLK, cdiv);
+ /* handle all the modes */
+ if ((spi->mode & SPI_3WIRE) && (tfr->rx_buf))
+ cs |= BCM2835_SPI_CS_REN;
if (spi->mode & SPI_CPOL)
cs |= BCM2835_SPI_CS_CPOL;
if (spi->mode & SPI_CPHA)
cs |= BCM2835_SPI_CS_CPHA;
- if (!(spi->mode & SPI_NO_CS)) {
- if (spi->mode & SPI_CS_HIGH) {
- cs |= BCM2835_SPI_CS_CSPOL;
- cs |= BCM2835_SPI_CS_CSPOL0 << spi->chip_select;
- }
-
- cs |= spi->chip_select;
- }
+ /* for gpio_cs set dummy CS so that no HW-CS get changed
+ * we can not run this in bcm2835_spi_set_cs, as it does
+ * not get called for cs_gpio cases, so we need to do it here
+ */
+ if (gpio_is_valid(spi->cs_gpio) || (spi->mode & SPI_NO_CS))
+ cs |= BCM2835_SPI_CS_CS_10 | BCM2835_SPI_CS_CS_01;
- reinit_completion(&bs->done);
+ /* set transmit buffers and length */
bs->tx_buf = tfr->tx_buf;
bs->rx_buf = tfr->rx_buf;
- bs->len = tfr->len;
+ bs->tx_len = tfr->len;
+ bs->rx_len = tfr->len;
- bcm2835_wr(bs, BCM2835_SPI_CLK, cdiv);
- /*
- * Enable the HW block. This will immediately trigger a DONE (TX
- * empty) interrupt, upon which we will fill the TX FIFO with the
- * first TX bytes. Pre-filling the TX FIFO here to avoid the
- * interrupt doesn't work:-(
- */
- bcm2835_wr(bs, BCM2835_SPI_CS, cs);
+ /* calculate the estimated time in us the transfer runs */
+ xfer_time_us = tfr->len
+ * 9 /* clocks/byte - SPI-HW waits 1 clock after each byte */
+ * 1000000 / spi_used_hz;
- return 0;
+ /* for short requests run polling*/
+ if (xfer_time_us <= BCM2835_SPI_POLLING_LIMIT_US)
+ return bcm2835_spi_transfer_one_poll(master, spi, tfr,
+ cs, xfer_time_us);
+
+ return bcm2835_spi_transfer_one_irq(master, spi, tfr, cs);
}
-static int bcm2835_spi_finish_transfer(struct spi_device *spi,
- struct spi_transfer *tfr, bool cs_change)
+static void bcm2835_spi_handle_err(struct spi_master *master,
+ struct spi_message *msg)
{
- struct bcm2835_spi *bs = spi_master_get_devdata(spi->master);
- u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+ bcm2835_spi_reset_hw(master);
+}
+
+static void bcm2835_spi_set_cs(struct spi_device *spi, bool gpio_level)
+{
+ /*
+ * we can assume that we are "native" as per spi_set_cs
+ * calling us ONLY when cs_gpio is not set
+ * we can also assume that we are CS < 3 as per bcm2835_spi_setup
+ * we would not get called because of error handling there.
+ * the level passed is the electrical level not enabled/disabled
+ * so it has to get translated back to enable/disable
+ * see spi_set_cs in spi.c for the implementation
+ */
- /* Drain RX FIFO */
- while (cs & BCM2835_SPI_CS_RXD) {
- bcm2835_rd_fifo(bs, 1);
- cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+ struct spi_master *master = spi->master;
+ struct bcm2835_spi *bs = spi_master_get_devdata(master);
+ u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+ bool enable;
+
+ /* calculate the enable flag from the passed gpio_level */
+ enable = (spi->mode & SPI_CS_HIGH) ? gpio_level : !gpio_level;
+
+ /* set flags for "reverse" polarity in the registers */
+ if (spi->mode & SPI_CS_HIGH) {
+ /* set the correct CS-bits */
+ cs |= BCM2835_SPI_CS_CSPOL;
+ cs |= BCM2835_SPI_CS_CSPOL0 << spi->chip_select;
+ } else {
+ /* clean the CS-bits */
+ cs &= ~BCM2835_SPI_CS_CSPOL;
+ cs &= ~(BCM2835_SPI_CS_CSPOL0 << spi->chip_select);
}
- if (tfr->delay_usecs)
- udelay(tfr->delay_usecs);
+ /* select the correct chip_select depending on disabled/enabled */
+ if (enable) {
+ /* set cs correctly */
+ if (spi->mode & SPI_NO_CS) {
+ /* use the "undefined" chip-select */
+ cs |= BCM2835_SPI_CS_CS_10 | BCM2835_SPI_CS_CS_01;
+ } else {
+ /* set the chip select */
+ cs &= ~(BCM2835_SPI_CS_CS_10 | BCM2835_SPI_CS_CS_01);
+ cs |= spi->chip_select;
+ }
+ } else {
+ /* disable CSPOL which puts HW-CS into deselected state */
+ cs &= ~BCM2835_SPI_CS_CSPOL;
+ /* use the "undefined" chip-select as precaution */
+ cs |= BCM2835_SPI_CS_CS_10 | BCM2835_SPI_CS_CS_01;
+ }
- if (cs_change)
- /* Clear TA flag */
- bcm2835_wr(bs, BCM2835_SPI_CS, cs & ~BCM2835_SPI_CS_TA);
+ /* finally set the calculated flags in SPI_CS */
+ bcm2835_wr(bs, BCM2835_SPI_CS, cs);
+}
- return 0;
+static int chip_match_name(struct gpio_chip *chip, void *data)
+{
+ return !strcmp(chip->label, data);
}
-static int bcm2835_spi_transfer_one(struct spi_master *master,
- struct spi_message *mesg)
+static int bcm2835_spi_setup(struct spi_device *spi)
{
- struct bcm2835_spi *bs = spi_master_get_devdata(master);
- struct spi_transfer *tfr;
- struct spi_device *spi = mesg->spi;
- int err = 0;
- unsigned int timeout;
- bool cs_change;
-
- list_for_each_entry(tfr, &mesg->transfers, transfer_list) {
- err = bcm2835_spi_start_transfer(spi, tfr);
- if (err)
- goto out;
-
- timeout = wait_for_completion_timeout(&bs->done,
- msecs_to_jiffies(BCM2835_SPI_TIMEOUT_MS));
- if (!timeout) {
- err = -ETIMEDOUT;
- goto out;
- }
+ int err;
+ struct gpio_chip *chip;
+ /*
+ * sanity checking the native-chipselects
+ */
+ if (spi->mode & SPI_NO_CS)
+ return 0;
+ if (gpio_is_valid(spi->cs_gpio))
+ return 0;
+ if (spi->chip_select > 1) {
+ /* error in the case of native CS requested with CS > 1
+ * officially there is a CS2, but it is not documented
+ * which GPIO is connected with that...
+ */
+ dev_err(&spi->dev,
+ "setup: only two native chip-selects are supported\n");
+ return -EINVAL;
+ }
+ /* now translate native cs to GPIO */
- cs_change = tfr->cs_change ||
- list_is_last(&tfr->transfer_list, &mesg->transfers);
+ /* get the gpio chip for the base */
+ chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
+ if (!chip)
+ return 0;
- err = bcm2835_spi_finish_transfer(spi, tfr, cs_change);
- if (err)
- goto out;
+ /* and calculate the real CS */
+ spi->cs_gpio = chip->base + 8 - spi->chip_select;
- mesg->actual_length += (tfr->len - bs->len);
- }
+ /* and set up the "mode" and level */
+ dev_info(&spi->dev, "setting up native-CS%i as GPIO %i\n",
+ spi->chip_select, spi->cs_gpio);
-out:
- /* Clear FIFOs, and disable the HW block */
- bcm2835_wr(bs, BCM2835_SPI_CS,
- BCM2835_SPI_CS_CLEAR_RX | BCM2835_SPI_CS_CLEAR_TX);
- mesg->status = err;
- spi_finalize_current_message(master);
+ /* set up GPIO as output and pull to the correct level */
+ err = gpio_direction_output(spi->cs_gpio,
+ (spi->mode & SPI_CS_HIGH) ? 0 : 1);
+ if (err) {
+ dev_err(&spi->dev,
+ "could not set CS%i gpio %i as output: %i",
+ spi->chip_select, spi->cs_gpio, err);
+ return err;
+ }
+ /* the implementation of pinctrl-bcm2835 currently does not
+ * set the GPIO value when using gpio_direction_output
+ * so we are setting it here explicitly
+ */
+ gpio_set_value(spi->cs_gpio, (spi->mode & SPI_CS_HIGH) ? 0 : 1);
return 0;
}
@@ -312,13 +426,14 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
master->mode_bits = BCM2835_SPI_MODE_BITS;
master->bits_per_word_mask = SPI_BPW_MASK(8);
master->num_chipselect = 3;
- master->transfer_one_message = bcm2835_spi_transfer_one;
+ master->setup = bcm2835_spi_setup;
+ master->set_cs = bcm2835_spi_set_cs;
+ master->transfer_one = bcm2835_spi_transfer_one;
+ master->handle_err = bcm2835_spi_handle_err;
master->dev.of_node = pdev->dev.of_node;
bs = spi_master_get_devdata(master);
- init_completion(&bs->done);
-
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
bs->regs = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(bs->regs)) {
@@ -343,13 +458,13 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
clk_prepare_enable(bs->clk);
err = devm_request_irq(&pdev->dev, bs->irq, bcm2835_spi_interrupt, 0,
- dev_name(&pdev->dev), master);
+ dev_name(&pdev->dev), master);
if (err) {
dev_err(&pdev->dev, "could not request IRQ: %d\n", err);
goto out_clk_disable;
}
- /* initialise the hardware */
+ /* initialise the hardware with the default polarities */
bcm2835_wr(bs, BCM2835_SPI_CS,
BCM2835_SPI_CS_CLEAR_RX | BCM2835_SPI_CS_CLEAR_TX);