diff options
Diffstat (limited to 'drivers/tty/serial')
| -rw-r--r-- | drivers/tty/serial/amba-pl011.c | 123 |
1 files changed, 122 insertions, 1 deletions
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 8dc0541feecc..f5f6831b0a64 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -50,6 +50,7 @@ #include <linux/dmaengine.h> #include <linux/dma-mapping.h> #include <linux/scatterlist.h> +#include <linux/delay.h> #include <asm/io.h> #include <asm/sizes.h> @@ -65,6 +66,30 @@ #define UART_DR_ERROR (UART011_DR_OE|UART011_DR_BE|UART011_DR_PE|UART011_DR_FE) #define UART_DUMMY_DR_RX (1 << 16) + +#define UART_WA_SAVE_NR 14 + +static void pl011_lockup_wa(unsigned long data); +static const u32 uart_wa_reg[UART_WA_SAVE_NR] = { + ST_UART011_DMAWM, + ST_UART011_TIMEOUT, + ST_UART011_LCRH_RX, + UART011_IBRD, + UART011_FBRD, + ST_UART011_LCRH_TX, + UART011_IFLS, + ST_UART011_XFCR, + ST_UART011_XON1, + ST_UART011_XON2, + ST_UART011_XOFF1, + ST_UART011_XOFF2, + UART011_CR, + UART011_IMSC +}; + +static u32 uart_wa_regdata[UART_WA_SAVE_NR]; +static DECLARE_TASKLET(pl011_lockup_tlet, pl011_lockup_wa, 0); + /* There is by now at least one vendor with differing details, so handle it */ struct vendor_data { unsigned int ifls; @@ -72,6 +97,7 @@ struct vendor_data { unsigned int lcrh_tx; unsigned int lcrh_rx; bool oversampling; + bool interrupt_may_hang; /* vendor-specific */ bool dma_threshold; }; @@ -90,9 +116,12 @@ static struct vendor_data vendor_st = { .lcrh_tx = ST_UART011_LCRH_TX, .lcrh_rx = ST_UART011_LCRH_RX, .oversampling = true, + .interrupt_may_hang = true, .dma_threshold = true, }; +static struct uart_amba_port *amba_ports[UART_NR]; + /* Deals with DMA transactions */ struct pl011_sgbuf { @@ -132,6 +161,7 @@ struct uart_amba_port { unsigned int lcrh_rx; /* vendor-specific */ bool autorts; char type[12]; + bool interrupt_may_hang; /* vendor-specific */ #ifdef CONFIG_DMA_ENGINE /* DMA stuff */ bool using_tx_dma; @@ -1008,6 +1038,68 @@ static inline bool pl011_dma_rx_running(struct uart_amba_port *uap) #endif +/* + * pl011_lockup_wa + * This workaround aims to break the deadlock situation + * when after long transfer over uart in hardware flow + * control, uart interrupt registers cannot be cleared. + * Hence uart transfer gets blocked. + * + * It is seen that during such deadlock condition ICR + * don't get cleared even on multiple write. This leads + * pass_counter to decrease and finally reach zero. This + * can be taken as trigger point to run this UART_BT_WA. + * + */ +static void pl011_lockup_wa(unsigned long data) +{ + struct uart_amba_port *uap = amba_ports[0]; + void __iomem *base = uap->port.membase; + struct circ_buf *xmit = &uap->port.state->xmit; + struct tty_struct *tty = uap->port.state->port.tty; + int buf_empty_retries = 200; + int loop; + + /* Stop HCI layer from submitting data for tx */ + tty->hw_stopped = 1; + while (!uart_circ_empty(xmit)) { + if (buf_empty_retries-- == 0) + break; + udelay(100); + } + + /* Backup registers */ + for (loop = 0; loop < UART_WA_SAVE_NR; loop++) + uart_wa_regdata[loop] = readl(base + uart_wa_reg[loop]); + + /* Disable UART so that FIFO data is flushed out */ + writew(0x00, uap->port.membase + UART011_CR); + + /* Soft reset UART module */ + if (uap->port.dev->platform_data) { + struct amba_pl011_data *plat; + + plat = uap->port.dev->platform_data; + if (plat->reset) + plat->reset(); + } + + /* Restore registers */ + for (loop = 0; loop < UART_WA_SAVE_NR; loop++) + writew(uart_wa_regdata[loop] , + uap->port.membase + uart_wa_reg[loop]); + + /* Initialise the old status of the modem signals */ + uap->old_status = readw(uap->port.membase + UART01x_FR) & + UART01x_FR_MODEM_ANY; + + if (readl(base + UART011_MIS) & 0x2) + printk(KERN_EMERG "UART_BT_WA: ***FAILED***\n"); + + /* Start Tx/Rx */ + tty->hw_stopped = 0; +} + static void pl011_stop_tx(struct uart_port *port) { struct uart_amba_port *uap = (struct uart_amba_port *)port; @@ -1158,8 +1250,11 @@ static irqreturn_t pl011_int(int irq, void *dev_id) if (status & UART011_TXIS) pl011_tx_chars(uap); - if (pass_counter-- == 0) + if (pass_counter-- == 0) { + if (uap->interrupt_may_hang) + tasklet_schedule(&pl011_lockup_tlet); break; + } status = readw(uap->port.membase + UART011_MIS); } while (status != 0); @@ -1339,6 +1434,14 @@ static int pl011_startup(struct uart_port *port) writew(uap->im, uap->port.membase + UART011_IMSC); spin_unlock_irq(&uap->port.lock); + if (uap->port.dev->platform_data) { + struct amba_pl011_data *plat; + + plat = uap->port.dev->platform_data; + if (plat->init) + plat->init(); + } + return 0; clk_dis: @@ -1394,6 +1497,15 @@ static void pl011_shutdown(struct uart_port *port) * Shut down the clock producer */ clk_disable(uap->clk); + + if (uap->port.dev->platform_data) { + struct amba_pl011_data *plat; + + plat = uap->port.dev->platform_data; + if (plat->exit) + plat->exit(); + } + } static void @@ -1700,6 +1812,14 @@ static int __init pl011_console_setup(struct console *co, char *options) if (!uap) return -ENODEV; + if (uap->port.dev->platform_data) { + struct amba_pl011_data *plat; + + plat = uap->port.dev->platform_data; + if (plat->init) + plat->init(); + } + uap->port.uartclk = clk_get_rate(uap->clk); if (options) @@ -1774,6 +1894,7 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id) uap->lcrh_rx = vendor->lcrh_rx; uap->lcrh_tx = vendor->lcrh_tx; uap->fifosize = vendor->fifosize; + uap->interrupt_may_hang = vendor->interrupt_may_hang; uap->port.dev = &dev->dev; uap->port.mapbase = dev->res.start; uap->port.membase = base; |