summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2007-10-10Sysace: sparse fixesGrant Likely
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Sysace: Minor coding convention fixupGrant Likely
Put function call and return code test on separate lines. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10drivers/block/umem: use DRIVER_NAME where appropriateJeff Garzik
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10drivers/block/umem: trim trailing whitespaceJeff Garzik
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10drivers/block/umem: minor cleanupsJeff Garzik
* tab-align DRIVER_*, pci_driver entries * reduced wasted memory by killing unused struct cardinfo members * move free_irq() call above resource unmap, to fix tiny window where irq handler may access recently-unmapped memory * propagate pci_enable_device() return value * use pci_request_regions, pci_release_regions() for resource reservation * call pci_disable_device() in pci_driver::remove() Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10drivers/block/umem: use dev_printk()Jeff Garzik
dev_printk() gives us a consistent prefix (driver name + PCI bus id), which allows us to eliminate the hand-rolled one. Also allows us to eliminate card->card_number, which was used solely in printk() calls. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10drivers/block/umem: move private include away from include/linuxJeff Garzik
Move include/linux/umem.h to drivers/block, as umem.c is the only user, and its not an exported header. Move the PCI_{VENDOR,DEVICE}_ID_* constants to include/linux/pci_ids.h. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10Sysace: Labels in C code should not be indented.Grant Likely
Remove the indentation on labels Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Sysace: Add of_platform_bus bindingGrant Likely
The of_platform bus binding is needed to make the device driver usable under arch/powerpc. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Sysace: Move IRQ handler registration to occur after FSM is initializedGrant Likely
The FSM needs to be initialized before it is safe to call the ISR Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Sysace: minor rework and cleanup changesGrant Likely
Miscellanious rework to the sysace driver; Not critical, but makes the subsequent addition of the of_platform bus binding a wee bit cleaner Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Sysace: Move structure allocation from bus binding into common codeGrant Likely
Split the determination of device registers/irqs/etc from the actual allocation and initialization of the device structure. This cleans up the code a bit in preparation to add an of_platform bus binding Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Sysace: Use the established platform bus apiGrant Likely
SystemACE uses the platform bus binding, but it doesn't use the platform bus API. Move to using the correct API for consistency sake and future proofing against platform bus changes. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Add Xilinx SystemACE entry to maintainersGrant Likely
I'm the author of the SystemACE driver Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Drop 'size' argument from bio_endio and bi_end_ioNeilBrown
As bi_end_io is only called once when the reqeust is complete, the 'size' argument is now redundant. Remove it. Now there is no need for bio_endio to subtract the size completed from bi_size. So don't do that either. While we are at it, change bi_end_io to return void. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Don't decrement bi_size in bio_endioNeilBrown
The only caller of bio_endio that does not pass the full bi_size is end_that_request_first. Also, no ->bi_end_io method is really interested in bi_size being decremented. So move the decrement and related code into ll_rw_blk and merge it with order_bio_endio to form req_bio_endio which does endio functionality specific to request completion. As some ->bi_end_io methods do check bi_size of 0, we set it thus for now, but that will go in the next patch. Signed-off-by: Neil Brown <neilb@suse.de> ### Diffstat output ./block/ll_rw_blk.c | 42 +++++++++++++++++++++++++++--------------- ./fs/bio.c | 23 +++++++++++------------ 2 files changed, 38 insertions(+), 27 deletions(-) diff .prev/block/ll_rw_blk.c ./block/ll_rw_blk.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Only call bi_end_io once for any bioNeilBrown
Currently bi_end_io can be called multiple times as sub-requests complete. However no ->bi_end_io function wants to know about that. So only call when the bio is complete. Signed-off-by: Neil Brown <neilb@suse.de> ### Diffstat output ./fs/bio.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff .prev/fs/bio.c ./fs/bio.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Remove flush_dry_bio_endioNeilBrown
The entire function of flush_dry_bio_endio is to undo the effects of bio_endio (when called on a barrier request). So remove the function and the call to bio_endio. This allows us to remove "bi_size" from "struct request_queue". Signed-off-by: Neil Brown <neilb@suse.de> ### Diffstat output ./block/ll_rw_blk.c | 39 ++------------------------------------- ./include/linux/blkdev.h | 1 - 2 files changed, 2 insertions(+), 38 deletions(-) diff .prev/block/ll_rw_blk.c ./block/ll_rw_blk.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Fix warnings with !CONFIG_BLOCKJens Axboe
Hide everything in blkdev.h with CONFIG_BLOCK isn't set, and fixup the (few) files that fail to build because they were relying on blkdev.h pulling in extra includes for them. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Corrections in Documentation/block/ioprio.txtDhaval Giani
The newer glibc does not allow system calls to be made via _syscallN() wrapper. They have to be made through syscall(). The ionice code used the older interface. Correcting it to use syscall. Signed-off-by: Dhaval Giani <dhaval@linux.vnet.ibm.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10ll_rw_blk: blk_cpu_notifier should be __cpuinitdataSatyam Sharma
blk_cpu_notifier is marked as __devinitdata, but __devinitdata need not be __init even if HOTPLUG_CPU=n, which wastes space. It should be marked __cpuinitdata, and the callback itself as __cpuinit. Signed-off-by: Satyam Sharma <satyam@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Fixup rq_for_each_segment() indentationJens Axboe
Remove one level of nesting where appropriate. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Share code between init_request_from_bio and blk_rq_bio_prepNeilBrown
These have very similar functions and should share code where possible. Signed-off-by: Neil Brown <neilb@suse.de> diff .prev/block/ll_rw_blk.c ./block/ll_rw_blk.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Stop exporting blk_rq_bio_prepNeilBrown
blk_rq_bio_prep is exported for use in exactly one place. That place can benefit from using the new blk_rq_append_bio instead. So - change dm-emc to call blk_rq_append_bio - stop exporting blk_rq_bio_prep, and - initialise rq_disk in blk_rq_bio_prep, as dm-emc needs it. Signed-off-by: Neil Brown <neilb@suse.de> diff .prev/block/ll_rw_blk.c ./block/ll_rw_blk.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10New function blk_req_append_bioNeilBrown
ll_back_merge_fn is currently exported to SCSI where is it used, together with blk_rq_bio_prep, in exactly the same way these functions are used in __blk_rq_map_user. So move the common code into a new function (blk_rq_append_bio), and don't export ll_back_merge_fn any longer. Signed-off-by: Neil Brown <neilb@suse.de> diff .prev/block/ll_rw_blk.c ./block/ll_rw_blk.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Fix various abuse of bio fields in umem.cNeilBrown
umem.c: advances bi_idx and bi_sector to track where it is up to. But it is only ever doing this on one bio, so the updated fields can easily be kept elsewhere (current_*). updates bi_size, but never uses the updated values, so this isn't needed. reuses bi_phys_segments to count how many iovecs have been completely. As the completion happens sequentiually, we can store this information outside the bio too. Signed-off-by: Neil Brown <neilb@suse.de> diff .prev/drivers/block/umem.c ./drivers/block/umem.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Introduce rq_for_each_segment replacing rq_for_each_bioNeilBrown
Every usage of rq_for_each_bio wraps a usage of bio_for_each_segment, so these can be combined into rq_for_each_segment. We define "struct req_iterator" to hold the 'bio' and 'index' that are needed for the double iteration. Signed-off-by: Neil Brown <neilb@suse.de> Various compile fixes by me... Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-10Merge blk_recount_segments into blk_recalc_rq_segmentsNeilBrown
blk_recalc_rq_segments calls blk_recount_segments on each bio, then does some extra calculations to handle segments that overlap two bios. If we merge the code from blk_recount_segments into blk_recalc_rq_segments, we can process the whole request one bio_vec at a time, and not need the messy cross-bio calculations. Then blk_recount_segments can be implemented by calling blk_recalc_rq_segments, passing it a simple on-stack request which stores just the bio. Signed-off-by: Neil Brown <neilb@suse.de> diff .prev/block/ll_rw_blk.c ./block/ll_rw_blk.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-09Linux 2.6.23Linus Torvalds
2007-10-09Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: [MIPS] Au1000: set the PCI controller IO base [MIPS] Alchemy: Fix USB initialization. [MIPS] IP32: Fix fatal typo in address computation.
2007-10-09NLM: Fix a memory leak in nlmsvc_testlockTrond Myklebust
The recent fix for a circular lock dependency unfortunately introduced a potential memory leak in the event where the call to nlmsvc_lookup_host fails for some reason. Thanks to Roel Kluin for spotting this. Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-09sata_mv: correct S/G table limitsJeff Garzik
The recent mv_fill_sg() rewrite, to fix a data corruption problem related to IOMMU virtual merging, forgot to account for the potentially-increased size of the scatter/gather table after its run. Additionally, the DMA boundary is reduced from 0xffffffff to 0xffff to more closely match the needs of mv_fill_sg(). Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-09[MIPS] Au1000: set the PCI controller IO baseFlorian Fainelli
The PCI controller IO base was not set in the au1000 pci code. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-10-09[MIPS] Alchemy: Fix USB initialization.Florian Fainelli
This patch fixes a wrong ifdef in the board setup code, leading to the GPIO pin not being pulled high, and thus the USB switch not being powered at all. This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which started in 2005 (before 2.6.12-rc2), then probably because things were working anyway for most people got forgotten. [Ralf: Paolo's original patch didn't fix the module case, Florian's patch only fixed MTX1 etc. so this is a combined patch plus some cleanups.] Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-10-09[MIPS] IP32: Fix fatal typo in address computation.Giuseppe Sacco
Signed-off-by: Giuseppe Sacco <eppesuig@debian.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-10-08Correct Makefile rule for generating custom keymapMaarten Bressers
When building a custom keymap, after setting GENERATE_KEYMAP := 1 in drivers/char/Makefile, the kernel build fails like this: CC drivers/char/vt.o make[2]: *** No rule to make target `drivers/char/%.map', needed by `drivers/char/defkeymap.c'. Stop. make[1]: *** [drivers/char] Error 2 make: *** [drivers] Error 2 This was caused by commit af8b128719f5248e542036ea994610a29d0642a6, which deleted a necessary colon from the Makefile rule that generates the keymap, since that rule contains both a target and a target-pattern. The following patch puts the colon back: Signed-off-by: Maarten Bressers <mbres@gentoo.org> Cc: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-08ISDN: Fix data access out of array boundsKarsten Keil
Fix against access random data bytes outside the dev->chanmap array. Thanks to Oliver Neukum for pointing me to this issue. Signed-off-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-08Merge branch 'master' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 * 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [IPv6]: Fix ICMPv6 redirect handling with target multicast address [PKT_SCHED] cls_u32: error code isn't been propogated properly [ROSE]: Fix rose.ko oops on unload [TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKed
2007-10-08AIO: fix cleanup in io_submit_one(...)Yan Zheng
When IOCB_FLAG_RESFD flag is set and iocb->aio_resfd is incorrect, statement 'goto out_put_req' is executed. At label 'out_put_req', aio_put_req(..) is called, which requires 'req->ki_filp' set. Signed-off-by: Yan Zheng<yanzheng@21cn.com> Cc: Zach Brown <zach.brown@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-08fix page release issue in filemap_faultYan Zheng
find_lock_page increases page's usage count, we should decrease it before return VM_FAULT_SIGBUS Signed-off-by: Yan Zheng<yanzheng@21cn.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-08fix VM_CAN_NONLINEAR check in sys_remap_file_pagesYan Zheng
The test for VM_CAN_NONLINEAR always fails Signed-off-by: Yan Zheng<yanzheng@21cn.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-08mm: set_page_dirty_balance() vs ->page_mkwrite()Peter Zijlstra
All the current page_mkwrite() implementations also set the page dirty. Which results in the set_page_dirty_balance() call to _not_ call balance, because the page is already found dirty. This allows us to dirty a _lot_ of pages without ever hitting balance_dirty_pages(). Not good (tm). Force a balance call if ->page_mkwrite() was successful. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-08[IPv6]: Fix ICMPv6 redirect handling with target multicast addressBrian Haley
When the ICMPv6 Target address is multicast, Linux processes the redirect instead of dropping it. The problem is in this code in ndisc_redirect_rcv(): if (ipv6_addr_equal(dest, target)) { on_link = 1; } else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) { ND_PRINTK2(KERN_WARNING "ICMPv6 Redirect: target address is not link-local.\n"); return; } This second check will succeed if the Target address is, for example, FF02::1 because it has link-local scope. Instead, it should be checking if it's a unicast link-local address, as stated in RFC 2461/4861 Section 8.1: - The ICMP Target Address is either a link-local address (when redirected to a router) or the same as the ICMP Destination Address (when redirected to the on-link destination). I know this doesn't explicitly say unicast link-local address, but it's implied. This bug is preventing Linux kernels from achieving IPv6 Logo Phase II certification because of a recent error that was found in the TAHI test suite - Neighbor Disovery suite test 206 (v6LC.2.3.6_G) had the multicast address in the Destination field instead of Target field, so we were passing the test. This won't be the case anymore. The patch below fixes this problem, and also fixes ndisc_send_redirect() to not send an invalid redirect with a multicast address in the Target field. I re-ran the TAHI Neighbor Discovery section to make sure Linux passes all 245 tests now. Signed-off-by: Brian Haley <brian.haley@hp.com> Acked-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-07[PKT_SCHED] cls_u32: error code isn't been propogated properlyStephen Hemminger
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-07[ROSE]: Fix rose.ko oops on unloadAlexey Dobriyan
Commit a3d384029aa304f8f3f5355d35f0ae274454f7cd aka "[AX.25]: Fix unchecked rose_add_loopback_neigh uses" transformed rose_loopback_neigh var into statically allocated one. However, on unload it will be kfree's which can't work. Steps to reproduce: modprobe rose rmmod rose BUG: unable to handle kernel NULL pointer dereference at virtual address 00000008 printing eip: c014c664 *pde = 00000000 Oops: 0000 [#1] PREEMPT DEBUG_PAGEALLOC Modules linked in: rose ax25 fan ufs loop usbhid rtc snd_intel8x0 snd_ac97_codec ehci_hcd ac97_bus uhci_hcd thermal usbcore button processor evdev sr_mod cdrom CPU: 0 EIP: 0060:[<c014c664>] Not tainted VLI EFLAGS: 00210086 (2.6.23-rc9 #3) EIP is at kfree+0x48/0xa1 eax: 00000556 ebx: c1734aa0 ecx: f6a5e000 edx: f7082000 esi: 00000000 edi: f9a55d20 ebp: 00200287 esp: f6a5ef28 ds: 007b es: 007b fs: 0000 gs: 0033 ss: 0068 Process rmmod (pid: 1823, ti=f6a5e000 task=f7082000 task.ti=f6a5e000) Stack: f9a55d20 f9a5200c 00000000 00000000 00000000 f6a5e000 f9a5200c f9a55a00 00000000 bf818cf0 f9a51f3f f9a55a00 00000000 c0132c60 65736f72 00000000 f69f9630 f69f9528 c014244a f6a4e900 00200246 f7082000 c01025e6 00000000 Call Trace: [<f9a5200c>] rose_rt_free+0x1d/0x49 [rose] [<f9a5200c>] rose_rt_free+0x1d/0x49 [rose] [<f9a51f3f>] rose_exit+0x4c/0xd5 [rose] [<c0132c60>] sys_delete_module+0x15e/0x186 [<c014244a>] remove_vma+0x40/0x45 [<c01025e6>] sysenter_past_esp+0x8f/0x99 [<c012bacf>] trace_hardirqs_on+0x118/0x13b [<c01025b6>] sysenter_past_esp+0x5f/0x99 ======================= Code: 05 03 1d 80 db 5b c0 8b 03 25 00 40 02 00 3d 00 40 02 00 75 03 8b 5b 0c 8b 73 10 8b 44 24 18 89 44 24 04 9c 5d fa e8 77 df fd ff <8b> 56 08 89 f8 e8 84 f4 fd ff e8 bd 32 06 00 3b 5c 86 60 75 0f EIP: [<c014c664>] kfree+0x48/0xa1 SS:ESP 0068:f6a5ef28 Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-07[TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKedIlpo Järvinen
When only GSO skb was partially ACKed, no hints are reset, therefore fastpath_cnt_hint must be tweaked too or else it can corrupt fackets_out. The corruption to occur, one must have non-trivial ACK/SACK sequence, so this bug is not very often that harmful. There's a fackets_out state reset in TCP because fackets_out is known to be inaccurate and that fixes the issue eventually anyway. In case there was also at least one skb that got fully ACKed, the fastpath_skb_hint is set to NULL which causes a recount for fastpath_cnt_hint (the old value won't be accessed anymore), thus it can safely be decremented without additional checking. Reported by Cedric Le Goater <clg@fr.ibm.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-07Driver core: fix SYSF_DEPRECATED breakage for nested classdevsDmitry Torokhov
We should only reparent to a class former class devices that form the base of class hierarchy. Nested devices should still grow from their real parents. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Tested-by: Andrey Borzenkov <arvidjaar@mail.ru> Tested-by: Anssi Hannula <anssi.hannula@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-07Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: firewire: point to migration document
2007-10-07Add manufacturer and card id of teltonica pcmcia modemsAttila Kinali
Add the manufacturer and card id of teltonica pcmcia modems to serial_cs.c Signed-off-by: Attila Kinali <attila@kinali.ch> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-07sysrq docs: document sequence that actually worksPavel Machek
Document sequence of keypresses that actually works. Yes, this changed year-or-so ago. Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-02 08:21:14 +0000