summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-01-23xfrm: Fix eth_hdr(skb)->h_proto to reflect inner IP versionYossi Kuperman
IPSec tunnel mode supports encapsulation of IPv4 over IPv6 and vice-versa. The outer IP header is stripped and the inner IP inherits the original Ethernet header. Tcpdump fails to properly decode the inner packet in case that h_proto is different than the inner IP version. Fix h_proto to reflect the inner IP version. Signed-off-by: Yossi Kuperman <yossiku@mellanox.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2018-01-19xfrm: fix error flow in case of add state failsAviad Yehezkel
If add state fails in case of device offload, netdev refcount will be negative since gc task is attempting to dev_free this state. This is fixed by putting NULL in state dev field. Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com> Signed-off-by: Boris Pismeny <borisp@mellanox.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2018-01-18xfrm: Add SA to hardware at the end of xfrm_state_construct()Yossi Kuperman
Current code configures the hardware with a new SA before the state has been fully initialized. During this time interval, an incoming ESP packet can cause a crash due to a NULL dereference. More specifically, xfrm_input() considers the packet as valid, and yet, anti-replay mechanism is not initialized. Move hardware configuration to the end of xfrm_state_construct(), and mark the state as valid once the SA is fully initialized. Fixes: d77e38e612a0 ("xfrm: Add an IPsec hardware offloading API") Signed-off-by: Aviad Yehezkel <aviadye@mellnaox.com> Signed-off-by: Aviv Heller <avivh@mellanox.com> Signed-off-by: Yossi Kuperman <yossiku@mellanox.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2018-01-17bpf: fix cls_bpf on filter replaceDaniel Borkmann
Running the following sequence is currently broken: # tc qdisc add dev foo clsact # tc filter replace dev foo ingress prio 1 handle 1 bpf da obj bar.o # tc filter replace dev foo ingress prio 1 handle 1 bpf da obj bar.o RTNETLINK answers: Invalid argument The normal expectation on kernel side is that the second command succeeds replacing the existing program. However, what happens is in cls_bpf_change(), we bail out with err in the second run in cls_bpf_offload(). The EINVAL comes directly in cls_bpf_offload() when comparing prog vs oldprog's gen_flags. In case of above replace the new prog's gen_flags are 0, but the old ones are 8, which means TCA_CLS_FLAGS_NOT_IN_HW is set (e.g. drivers not having cls_bpf offload). Fix 102740bd9436 ("cls_bpf: fix offload assumptions after callback conversion") in the following way: gen_flags from user space passed down via netlink cannot include status flags like TCA_CLS_FLAGS_IN_HW or TCA_CLS_FLAGS_NOT_IN_HW as opposed to oldprog that we previously loaded. Therefore, it doesn't make any sense to include them in the gen_flags comparison with the new prog before we even attempt to offload. Thus, lets fix this before 4.15 goes out. Fixes: 102740bd9436 ("cls_bpf: fix offload assumptions after callback conversion") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17Net: ethernet: ti: netcp: Fix inbound ping crash if MTU size is greater than ↵Rex Chang
1500 In the receive queue for 4096 bytes fragments, the page address set in the SW data0 field of the descriptor is not the one we got when doing the reassembly in receive. The page structure was retrieved from the wrong descriptor into SW data0 which is then causing a page fault when UDP checksum is accessing data above 1500. Signed-off-by: Rex Chang <rchang@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17tls: reset crypto_info when do_tls_setsockopt_tx failsSabrina Dubroca
The current code copies directly from userspace to ctx->crypto_send, but doesn't always reinitialize it to 0 on failure. This causes any subsequent attempt to use this setsockopt to fail because of the TLS_CRYPTO_INFO_READY check, eventhough crypto_info is not actually ready. This should result in a correctly set up socket after the 3rd call, but currently it does not: size_t s = sizeof(struct tls12_crypto_info_aes_gcm_128); struct tls12_crypto_info_aes_gcm_128 crypto_good = { .info.version = TLS_1_2_VERSION, .info.cipher_type = TLS_CIPHER_AES_GCM_128, }; struct tls12_crypto_info_aes_gcm_128 crypto_bad_type = crypto_good; crypto_bad_type.info.cipher_type = 42; setsockopt(sock, SOL_TLS, TLS_TX, &crypto_bad_type, s); setsockopt(sock, SOL_TLS, TLS_TX, &crypto_good, s - 1); setsockopt(sock, SOL_TLS, TLS_TX, &crypto_good, s); Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17tls: return -EBUSY if crypto_info is already setSabrina Dubroca
do_tls_setsockopt_tx returns 0 without doing anything when crypto_info is already set. Silent failure is confusing for users. Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17tls: fix sw_ctx leakSabrina Dubroca
During setsockopt(SOL_TCP, TLS_TX), if initialization of the software context fails in tls_set_sw_offload(), we leak sw_ctx. We also don't reassign ctx->priv_ctx to NULL, so we can't even do another attempt to set it up on the same socket, as it will fail with -EEXIST. Fixes: 3c4d7559159b ('tls: kernel TLS support') Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17Merge tag 'linux-can-fixes-for-4.15-20180116' of ↵David S. Miller
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2018-01-16 this is a pull reqeust of a single patch for net/master: This patch by Stephane Grosjean fixes a potential bug in the packet fragmentation in the peak USB driver. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17net/tls: Only attach to sockets in ESTABLISHED stateIlya Lesokhin
Calling accept on a TCP socket with a TLS ulp attached results in two sockets that share the same ulp context. The ulp context is freed while a socket is destroyed, so after one of the sockets is released, the second second will trigger a use after free when it tries to access the ulp context attached to it. We restrict the TLS ulp to sockets in ESTABLISHED state to prevent the scenario above. Fixes: 3c4d7559159b ("tls: kernel TLS support") Reported-by: syzbot+904e7cd6c5c741609228@syzkaller.appspotmail.com Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17net: fs_enet: do not call phy_stop() in interruptsChristophe Leroy
In case of TX timeout, fs_timeout() calls phy_stop(), which triggers the following BUG_ON() as we are in interrupt. [92708.199889] kernel BUG at drivers/net/phy/mdio_bus.c:482! [92708.204985] Oops: Exception in kernel mode, sig: 5 [#1] [92708.210119] PREEMPT [92708.212107] CMPC885 [92708.214216] CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G W 4.9.61 #39 [92708.223227] task: c60f0a40 task.stack: c6104000 [92708.227697] NIP: c02a84bc LR: c02a947c CTR: c02a93d8 [92708.232614] REGS: c6105c70 TRAP: 0700 Tainted: G W (4.9.61) [92708.241193] MSR: 00021032 <ME,IR,DR,RI>[92708.244818] CR: 24000822 XER: 20000000 [92708.248767] GPR00: c02a947c c6105d20 c60f0a40 c62b4c00 00000005 0000001f c069aad8 0001a688 GPR08: 00000007 00000100 c02a93d8 00000000 000005fc 00000000 c6213240 c06338e4 GPR16: 00000001 c06330d4 c0633094 00000000 c0680000 c6104000 c6104000 00000000 GPR24: 00000200 00000000 ffffffff 00000004 00000078 00009032 00000000 c62b4c00 NIP [c02a84bc] mdiobus_read+0x20/0x74 [92708.281517] LR [c02a947c] kszphy_config_intr+0xa4/0xc4 [92708.286547] Call Trace: [92708.288980] [c6105d20] [c6104000] 0xc6104000 (unreliable) [92708.294339] [c6105d40] [c02a947c] kszphy_config_intr+0xa4/0xc4 [92708.300098] [c6105d50] [c02a5330] phy_stop+0x60/0x9c [92708.305007] [c6105d60] [c02c84d0] fs_timeout+0xdc/0x110 [92708.310197] [c6105d80] [c035cd48] dev_watchdog+0x268/0x2a0 [92708.315593] [c6105db0] [c0060288] call_timer_fn+0x34/0x17c [92708.321014] [c6105dd0] [c00605f0] run_timer_softirq+0x21c/0x2e4 [92708.326887] [c6105e50] [c001e19c] __do_softirq+0xf4/0x2f4 [92708.332207] [c6105eb0] [c001e3c8] run_ksoftirqd+0x2c/0x40 [92708.337560] [c6105ec0] [c003b420] smpboot_thread_fn+0x1f0/0x258 [92708.343405] [c6105ef0] [c003745c] kthread+0xbc/0xd0 [92708.348217] [c6105f40] [c000c400] ret_from_kernel_thread+0x5c/0x64 [92708.354275] Instruction dump: [92708.357207] 7c0803a6 bbc10018 38210020 4e800020 7c0802a6 9421ffe0 54290024 bfc10018 [92708.364865] 90010024 7c7f1b78 81290008 552902ee <0f090000> 3bc3002c 7fc3f378 90810008 [92708.372711] ---[ end trace 42b05441616fafd7 ]--- This patch moves fs_timeout() actions into an async worker. Fixes: commit 48257c4f168e5 ("Add fs_enet ethernet network driver, for several embedded platforms") Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17r8152: disable RX aggregation on Dell TB16 dockKai-Heng Feng
r8153 on Dell TB15/16 dock corrupts rx packets. This change is suggested by Realtek. They guess that the XHCI controller doesn't have enough buffer, and their guesswork is correct, once the RX aggregation gets disabled, the issue is gone. ASMedia is currently working on a real sulotion for this issue. Dell and ODM confirm the bcdDevice and iSerialNumber is unique for TB16. Note that TB15 has different bcdDevice and iSerialNumber, which are not unique values. If you still have TB15, please contact Dell to replace it with TB16. BugLink: https://bugs.launchpad.net/bugs/1729674 Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17tun: fix a memory leak for tfile->tx_arrayCong Wang
tfile->tun could be detached before we close the tun fd, via tun_detach_all(), so it should not be used to check for tfile->tx_array. As Jason suggested, we probably have to clean it up unconditionally both in __tun_deatch() and tun_detach_all(), but this requires to check if it is initialized or not. Currently skb_array_cleanup() doesn't have such a check, so I check it in the caller and introduce a helper function, it is a bit ugly but we can always improve it in net-next. Reported-by: Dmitry Vyukov <dvyukov@google.com> Fixes: 1576d9860599 ("tun: switch to use skb array for tx") Cc: Jason Wang <jasowang@redhat.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdmaLinus Torvalds
Pull rdma fixes from Doug Ledford: "We had a few more items creep up over the last week. Given we are in -rc8, these are obviously limited to bugs that have a big downside and for which we are certain of the fix. The first is a straight up oops bug that all you have to do is read the code to see it's a guaranteed 100% oops bug. The second is a use-after-free issue. We get away lucky if the queue we are shutting down is empty, but if it isn't, we can end up oopsing. We really need to drain the queue before destroying it. The final one is an issue with bad user input causing us to access our port array out of bounds. While fixing the array out of bounds issue, it was noticed that the original code did the same thing twice (the call to rdma_ah_set_port_num()), so its removal is not balanced by a readd elsewhere, it was already where it needed to be in addition to where it didn't need to be. Summary: - Oops fix in hfi1 driver - use-after-free issue in iser-target - use of user supplied array index without proper checking" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: RDMA/mlx5: Fix out-of-bound access while querying AH IB/hfi1: Prevent a NULL dereference iser-target: Fix possible use-after-free in connection establishment error
2018-01-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: 1) Two read past end of buffer fixes in AF_KEY, from Eric Biggers. 2) Memory leak in key_notify_policy(), from Steffen Klassert. 3) Fix overflow with bpf arrays, from Daniel Borkmann. 4) Fix RDMA regression with mlx5 due to mlx5 no longer using pci_irq_get_affinity(), from Saeed Mahameed. 5) Missing RCU read locking in nl80211_send_iface() when it calls ieee80211_bss_get_ie(), from Dominik Brodowski. 6) cfg80211 should check dev_set_name()'s return value, from Johannes Berg. 7) Missing module license tag in 9p protocol, from Stephen Hemminger. 8) Fix crash due to too small MTU in udp ipv6 sendmsg, from Mike Maloney. 9) Fix endless loop in netlink extack code, from David Ahern. 10) TLS socket layer sets inverted error codes, resulting in an endless loop. From Robert Hering. 11) Revert openvswitch erspan tunnel support, it's mis-designed and we need to kill it before it goes into a real release. From William Tu. 12) Fix lan78xx failures in full speed USB mode, from Yuiko Oshino. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits) net, sched: fix panic when updating miniq {b,q}stats qed: Fix potential use-after-free in qed_spq_post() nfp: use the correct index for link speed table lan78xx: Fix failure in USB Full Speed sctp: do not allow the v4 socket to bind a v4mapped v6 address sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf sctp: reinit stream if stream outcnt has been change by sinit in sendmsg ibmvnic: Fix pending MAC address changes netlink: extack: avoid parenthesized string constant warning ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY net: Allow neigh contructor functions ability to modify the primary_key sh_eth: fix dumping ARSTR Revert "openvswitch: Add erspan tunnel support." net/tls: Fix inverted error codes to avoid endless loop ipv6: ip6_make_skb() needs to clear cork.base.dst sctp: avoid compiler warning on implicit fallthru net: ipv4: Make "ip route get" match iif lo rules again. netlink: extack needs to be reset each time through loop tipc: fix a memory leak in tipc_nl_node_get_link() ipv6: fix udpv6 sendmsg crash caused by too small MTU ...
2018-01-16Merge tag 'sound-4.15' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound fixes from Takashi Iwai: "A few small last-minute fixes that should sneak into 4.15: - remove a spurious WARN_ON() triggered by syzkaller - fix for ioctl races in ALSA sequencer - two trivial HD-audio fixup entries" * tag 'sound-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: seq: Make ioctls race-free ALSA: pcm: Remove yet superfluous WARN_ON() ALSA: hda - Apply the existing quirk to iMac 14,1 ALSA: hda - Apply headphone noise quirk for another Dell XPS 13 variant
2018-01-16Merge tag 'trace-v4.15-rc4-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fixes from Steven Rostedt: - Bring back context level recursive protection in ring buffer. The simpler counter protection failed, due to a path when tracing with trace_clock_global() as it could not be reentrant and depended on the ring buffer recursive protection to keep that from happening. - Prevent branch profiling when FORTIFY_SOURCE is enabled. It causes 50 - 60 MB in warning messages. Branch profiling should never be run on production systems, so there's no reason that it needs to be enabled with FORTIFY_SOURCE. * tag 'trace-v4.15-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing: Prevent PROFILE_ALL_BRANCHES when FORTIFY_SOURCE=y ring-buffer: Bring back context level recursive checks
2018-01-16net, sched: fix panic when updating miniq {b,q}statsDaniel Borkmann
While working on fixing another bug, I ran into the following panic on arm64 by simply attaching clsact qdisc, adding a filter and running traffic on ingress to it: [...] [ 178.188591] Unable to handle kernel read from unreadable memory at virtual address 810fb501f000 [ 178.197314] Mem abort info: [ 178.200121] ESR = 0x96000004 [ 178.203168] Exception class = DABT (current EL), IL = 32 bits [ 178.209095] SET = 0, FnV = 0 [ 178.212157] EA = 0, S1PTW = 0 [ 178.215288] Data abort info: [ 178.218175] ISV = 0, ISS = 0x00000004 [ 178.222019] CM = 0, WnR = 0 [ 178.224997] user pgtable: 4k pages, 48-bit VAs, pgd = 0000000023cb3f33 [ 178.231531] [0000810fb501f000] *pgd=0000000000000000 [ 178.236508] Internal error: Oops: 96000004 [#1] SMP [...] [ 178.311855] CPU: 73 PID: 2497 Comm: ping Tainted: G W 4.15.0-rc7+ #5 [ 178.319413] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB18A 03/31/2017 [ 178.326887] pstate: 60400005 (nZCv daif +PAN -UAO) [ 178.331685] pc : __netif_receive_skb_core+0x49c/0xac8 [ 178.336728] lr : __netif_receive_skb+0x28/0x78 [ 178.341161] sp : ffff00002344b750 [ 178.344465] x29: ffff00002344b750 x28: ffff810fbdfd0580 [ 178.349769] x27: 0000000000000000 x26: ffff000009378000 [...] [ 178.418715] x1 : 0000000000000054 x0 : 0000000000000000 [ 178.424020] Process ping (pid: 2497, stack limit = 0x000000009f0a3ff4) [ 178.430537] Call trace: [ 178.432976] __netif_receive_skb_core+0x49c/0xac8 [ 178.437670] __netif_receive_skb+0x28/0x78 [ 178.441757] process_backlog+0x9c/0x160 [ 178.445584] net_rx_action+0x2f8/0x3f0 [...] Reason is that sch_ingress and sch_clsact are doing mini_qdisc_pair_init() which sets up miniq pointers to cpu_{b,q}stats from the underlying qdisc. Problem is that this cannot work since they are actually set up right after the qdisc ->init() callback in qdisc_create(), so first packet going into sch_handle_ingress() tries to call mini_qdisc_bstats_cpu_update() and we therefore panic. In order to fix this, allocation of {b,q}stats needs to happen before we call into ->init(). In net-next, there's already such option through commit d59f5ffa59d8 ("net: sched: a dflt qdisc may be used with per cpu stats"). However, the bug needs to be fixed in net still for 4.15. Thus, include these bits to reduce any merge churn and reuse the static_flags field to set TCQ_F_CPUSTATS, and remove the allocation from qdisc_create() since there is no other user left. Prashant Bhole ran into the same issue but for net-next, thus adding him below as well as co-author. Same issue was also reported by Sandipan Das when using bcc. Fixes: 46209401f8f6 ("net: core: introduce mini_Qdisc and eliminate usage of tp->q for clsact fastpath") Reference: https://lists.iovisor.org/pipermail/iovisor-dev/2018-January/001190.html Reported-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Co-authored-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Co-authored-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16qed: Fix potential use-after-free in qed_spq_post()Roland Dreier
We need to check if p_ent->comp_mode is QED_SPQ_MODE_EBLOCK before calling qed_spq_add_entry(). The test is fine is the mode is EBLOCK, but if it isn't then qed_spq_add_entry() might kfree(p_ent). Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16nfp: use the correct index for link speed tableJakub Kicinski
sts variable is holding link speed as well as state. We should be using ls to index into ls_to_ethtool. Fixes: 265aeb511bd5 ("nfp: add support for .get_link_ksettings()") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16lan78xx: Fix failure in USB Full SpeedYuiko Oshino
Fix initialize the uninitialized tx_qlen to an appropriate value when USB Full Speed is used. Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16Merge tag 'mac80211-for-davem-2018-01-15' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== More fixes: * hwsim: - properly flush deletion works at module unload - validate # of channels passed from userspace * cfg80211: - fix RCU locking regression - initialize on-stack channel data for nl80211 event - check dev_set_name() return value ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16sctp: do not allow the v4 socket to bind a v4mapped v6 addressXin Long
The check in sctp_sockaddr_af is not robust enough to forbid binding a v4mapped v6 addr on a v4 socket. The worse thing is that v4 socket's bind_verify would not convert this v4mapped v6 addr to a v4 addr. syzbot even reported a crash as the v4 socket bound a v6 addr. This patch is to fix it by doing the common sa.sa_family check first, then AF_INET check for v4mapped v6 addrs. Fixes: 7dab83de50c7 ("sctp: Support ipv6only AF_INET6 sockets.") Reported-by: syzbot+7b7b518b1228d2743963@syzkaller.appspotmail.com Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbufXin Long
After commit cea0cc80a677 ("sctp: use the right sk after waking up from wait_buf sleep"), it may change to lock another sk if the asoc has been peeled off in sctp_wait_for_sndbuf. However, the asoc's new sk could be already closed elsewhere, as it's in the sendmsg context of the old sk that can't avoid the new sk's closing. If the sk's last one refcnt is held by this asoc, later on after putting this asoc, the new sk will be freed, while under it's own lock. This patch is to revert that commit, but fix the old issue by returning error under the old sk's lock. Fixes: cea0cc80a677 ("sctp: use the right sk after waking up from wait_buf sleep") Reported-by: syzbot+ac6ea7baa4432811eb50@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16sctp: reinit stream if stream outcnt has been change by sinit in sendmsgXin Long
After introducing sctp_stream structure, sctp uses stream->outcnt as the out stream nums instead of c.sinit_num_ostreams. However when users use sinit in cmsg, it only updates c.sinit_num_ostreams in sctp_sendmsg. At that moment, stream->outcnt is still using previous value. If it's value is not updated, the sinit_num_ostreams of sinit could not really work. This patch is to fix it by updating stream->outcnt and reiniting stream if stream outcnt has been change by sinit in sendmsg. Fixes: a83863174a61 ("sctp: prepare asoc stream for stream reconf") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16ibmvnic: Fix pending MAC address changesThomas Falcon
Due to architecture limitations, the IBM VNIC client driver is unable to perform MAC address changes unless the device has "logged in" to its backing device. Currently, pending MAC changes are handled before login, resulting in an error and failure to change the MAC address. Moving that chunk to the end of the ibmvnic_login function, when we are sure that it was successful, fixes that. The MAC address can be changed when the device is up or down, so only check if the device is in a "PROBED" state before setting the MAC address. Fixes: c26eba03e407 ("ibmvnic: Update reset infrastructure to support tunable parameters") Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Reviewed-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-16can: peak: fix potential bug in packet fragmentationStephane Grosjean
In some rare conditions when running one PEAK USB-FD interface over a non high-speed USB controller, one useless USB fragment might be sent. This patch fixes the way a USB command is fragmented when its length is greater than 64 bytes and when the underlying USB controller is not a high-speed one. Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-15RDMA/mlx5: Fix out-of-bound access while querying AHLeon Romanovsky
The rdma_ah_find_type() accesses the port array based on an index controlled by userspace. The existing bounds check is after the first use of the index, so userspace can generate an out of bounds access, as shown by the KASN report below. ================================================================== BUG: KASAN: slab-out-of-bounds in to_rdma_ah_attr+0xa8/0x3b0 Read of size 4 at addr ffff880019ae2268 by task ibv_rc_pingpong/409 CPU: 0 PID: 409 Comm: ibv_rc_pingpong Not tainted 4.15.0-rc2-00031-gb60a3faf5b83-dirty #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014 Call Trace: dump_stack+0xe9/0x18f print_address_description+0xa2/0x350 kasan_report+0x3a5/0x400 to_rdma_ah_attr+0xa8/0x3b0 mlx5_ib_query_qp+0xd35/0x1330 ib_query_qp+0x8a/0xb0 ib_uverbs_query_qp+0x237/0x7f0 ib_uverbs_write+0x617/0xd80 __vfs_write+0xf7/0x500 vfs_write+0x149/0x310 SyS_write+0xca/0x190 entry_SYSCALL_64_fastpath+0x18/0x85 RIP: 0033:0x7fe9c7a275a0 RSP: 002b:00007ffee5498738 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 00007fe9c7ce4b00 RCX: 00007fe9c7a275a0 RDX: 0000000000000018 RSI: 00007ffee5498800 RDI: 0000000000000003 RBP: 000055d0c8d3f010 R08: 00007ffee5498800 R09: 0000000000000018 R10: 00000000000000ba R11: 0000000000000246 R12: 0000000000008000 R13: 0000000000004fb0 R14: 000055d0c8d3f050 R15: 00007ffee5498560 Allocated by task 1: __kmalloc+0x3f9/0x430 alloc_mad_private+0x25/0x50 ib_mad_post_receive_mads+0x204/0xa60 ib_mad_init_device+0xa59/0x1020 ib_register_device+0x83a/0xbc0 mlx5_ib_add+0x50e/0x5c0 mlx5_add_device+0x142/0x410 mlx5_register_interface+0x18f/0x210 mlx5_ib_init+0x56/0x63 do_one_initcall+0x15b/0x270 kernel_init_freeable+0x2d8/0x3d0 kernel_init+0x14/0x190 ret_from_fork+0x24/0x30 Freed by task 0: (stack is not available) The buggy address belongs to the object at ffff880019ae2000 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 104 bytes to the right of 512-byte region [ffff880019ae2000, ffff880019ae2200) The buggy address belongs to the page: page:000000005d674e18 count:1 mapcount:0 mapping: (null) index:0x0 compound_mapcount: 0 flags: 0x4000000000008100(slab|head) raw: 4000000000008100 0000000000000000 0000000000000000 00000001000c000c raw: dead000000000100 dead000000000200 ffff88001a402000 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff880019ae2100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff880019ae2180: 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc >ffff880019ae2200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff880019ae2280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff880019ae2300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ================================================================== Disabling lock debugging due to kernel taint Cc: <stable@vger.kernel.org> Fixes: 44c58487d51a ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types") Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-01-15netlink: extack: avoid parenthesized string constant warningJohannes Berg
NL_SET_ERR_MSG() and NL_SET_ERR_MSG_ATTR() lead to the following warning in newer versions of gcc: warning: array initialized from parenthesized string constant Just remove the parentheses, they're not needed in this context since anyway since there can be no operator precendence issues or similar. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15Merge branch ↵David S. Miller
'ipv4-Make-neigh-lookup-keys-for-loopback-point-to-point-devices-be-INADDR_ANY' Jim Westfall says: ==================== ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY This used to be the previous behavior in older kernels but became broken in a263b3093641f (ipv4: Make neigh lookups directly in output packet path) and then later removed because it was broken in 0bb4087cbec0 (ipv4: Fix neigh lookup keying over loopback/point-to-point devices) Not having this results in there being an arp entry for every remote ip address that the device talks to. Given a fairly active device it can cause the arp table to become huge and/or having to add/purge large number of entires to keep within table size thresholds. $ ip -4 neigh show nud noarp | grep tun | wc -l 55850 $ lnstat -k arp_cache:entries,arp_cache:allocs,arp_cache:destroys -c 10 arp_cach|arp_cach|arp_cach| entries| allocs|destroys| 81493|620166816|620126069| 101867| 10186| 0| 113854| 5993| 0| 118773| 2459| 0| 27937| 18579| 63998| 39256| 5659| 0| 56231| 8487| 0| 65602| 4685| 0| 79697| 7047| 0| 90733| 5517| 0| v2: - fixes coding style issues ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANYJim Westfall
Map all lookup neigh keys to INADDR_ANY for loopback/point-to-point devices to avoid making an entry for every remote ip the device needs to talk to. This used the be the old behavior but became broken in a263b3093641f (ipv4: Make neigh lookups directly in output packet path) and later removed in 0bb4087cbec0 (ipv4: Fix neigh lookup keying over loopback/point-to-point devices) because it was broken. Signed-off-by: Jim Westfall <jwestfall@surrealistic.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15net: Allow neigh contructor functions ability to modify the primary_keyJim Westfall
Use n->primary_key instead of pkey to account for the possibility that a neigh constructor function may have modified the primary_key value. Signed-off-by: Jim Westfall <jwestfall@surrealistic.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15sh_eth: fix dumping ARSTRSergei Shtylyov
ARSTR is always located at the start of the TSU register region, thus using add_reg() instead of add_tsu_reg() in __sh_eth_get_regs() to dump it causes EDMR or EDSR (depending on the register layout) to be dumped instead of ARSTR. Use the correct condition/macro there... Fixes: 6b4b4fead342 ("sh_eth: Implement ethtool register dump operations") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15Revert "openvswitch: Add erspan tunnel support."William Tu
This reverts commit ceaa001a170e43608854d5290a48064f57b565ed. The OVS_TUNNEL_KEY_ATTR_ERSPAN_OPTS attr should be designed as a nested attribute to support all ERSPAN v1 and v2's fields. The current attr is a be32 supporting only one field. Thus, this patch reverts it and later patch will redo it using nested attr. Signed-off-by: William Tu <u9012063@gmail.com> Cc: Jiri Benc <jbenc@redhat.com> Cc: Pravin Shelar <pshelar@ovn.org> Acked-by: Jiri Benc <jbenc@redhat.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15net/tls: Fix inverted error codes to avoid endless loopr.hering@avm.de
sendfile() calls can hang endless with using Kernel TLS if a socket error occurs. Socket error codes must be inverted by Kernel TLS before returning because they are stored with positive sign. If returned non-inverted they are interpreted as number of bytes sent, causing endless looping of the splice mechanic behind sendfile(). Signed-off-by: Robert Hering <r.hering@avm.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15ipv6: ip6_make_skb() needs to clear cork.base.dstEric Dumazet
In my last patch, I missed fact that cork.base.dst was not initialized in ip6_make_skb() : If ip6_setup_cork() returns an error, we might attempt a dst_release() on some random pointer. Fixes: 862c03ee1deb ("ipv6: fix possible mem leaks in ipv6_make_skb()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15tracing: Prevent PROFILE_ALL_BRANCHES when FORTIFY_SOURCE=yRandy Dunlap
I regularly get 50 MB - 60 MB files during kernel randconfig builds. These large files mostly contain (many repeats of; e.g., 124,594): In file included from ../include/linux/string.h:6:0, from ../include/linux/uuid.h:20, from ../include/linux/mod_devicetable.h:13, from ../scripts/mod/devicetable-offsets.c:3: ../include/linux/compiler.h:64:4: warning: '______f' is static but declared in inline function 'strcpy' which is not static [enabled by default] ______f = { \ ^ ../include/linux/compiler.h:56:23: note: in expansion of macro '__trace_if' ^ ../include/linux/string.h:425:2: note: in expansion of macro 'if' if (p_size == (size_t)-1 && q_size == (size_t)-1) ^ This only happens when CONFIG_FORTIFY_SOURCE=y and CONFIG_PROFILE_ALL_BRANCHES=y, so prevent PROFILE_ALL_BRANCHES if FORTIFY_SOURCE=y. Link: http://lkml.kernel.org/r/9199446b-a141-c0c3-9678-a3f9107f2750@infradead.org Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2018-01-15sctp: avoid compiler warning on implicit fallthruMarcelo Ricardo Leitner
These fall-through are expected. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15net: ipv4: Make "ip route get" match iif lo rules again.Lorenzo Colitti
Commit 3765d35ed8b9 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup") broke "ip route get" in the presence of rules that specify iif lo. Host-originated traffic always has iif lo, because ip_route_output_key_hash and ip6_route_output_flags set the flow iif to LOOPBACK_IFINDEX. Thus, putting "iif lo" in an ip rule is a convenient way to select only originated traffic and not forwarded traffic. inet_rtm_getroute used to match these rules correctly because even though it sets the flow iif to 0, it called ip_route_output_key which overwrites iif with LOOPBACK_IFINDEX. But now that it calls ip_route_output_key_hash_rcu, the ifindex will remain 0 and not match the iif lo in the rule. As a result, "ip route get" will return ENETUNREACH. Fixes: 3765d35ed8b9 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup") Tested: https://android.googlesource.com/kernel/tests/+/master/net/test/multinetwork_test.py passes again Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15netlink: extack needs to be reset each time through loopDavid Ahern
syzbot triggered the WARN_ON in netlink_ack testing the bad_attr value. The problem is that netlink_rcv_skb loops over the skb repeatedly invoking the callback and without resetting the extack leaving potentially stale data. Initializing each time through avoids the WARN_ON. Fixes: 2d4bc93368f5a ("netlink: extended ACK reporting") Reported-by: syzbot+315fa6766d0f7c359327@syzkaller.appspotmail.com Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15tipc: fix a memory leak in tipc_nl_node_get_link()Cong Wang
When tipc_node_find_by_name() fails, the nlmsg is not freed. While on it, switch to a goto label to properly free it. Fixes: be9c086715c ("tipc: narrow down exposure of struct tipc_node") Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15ipv6: fix udpv6 sendmsg crash caused by too small MTUMike Maloney
The logic in __ip6_append_data() assumes that the MTU is at least large enough for the headers. A device's MTU may be adjusted after being added while sendmsg() is processing data, resulting in __ip6_append_data() seeing any MTU. For an mtu smaller than the size of the fragmentation header, the math results in a negative 'maxfraglen', which causes problems when refragmenting any previous skb in the skb_write_queue, leaving it possibly malformed. Instead sendmsg returns EINVAL when the mtu is calculated to be less than IPV6_MIN_MTU. Found by syzkaller: kernel BUG at ./include/linux/skbuff.h:2064! invalid opcode: 0000 [#1] SMP KASAN Dumping ftrace buffer: (ftrace buffer empty) Modules linked in: CPU: 1 PID: 14216 Comm: syz-executor5 Not tainted 4.13.0-rc4+ #2 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 task: ffff8801d0b68580 task.stack: ffff8801ac6b8000 RIP: 0010:__skb_pull include/linux/skbuff.h:2064 [inline] RIP: 0010:__ip6_make_skb+0x18cf/0x1f70 net/ipv6/ip6_output.c:1617 RSP: 0018:ffff8801ac6bf570 EFLAGS: 00010216 RAX: 0000000000010000 RBX: 0000000000000028 RCX: ffffc90003cce000 RDX: 00000000000001b8 RSI: ffffffff839df06f RDI: ffff8801d9478ca0 RBP: ffff8801ac6bf780 R08: ffff8801cc3f1dbc R09: 0000000000000000 R10: ffff8801ac6bf7a0 R11: 43cb4b7b1948a9e7 R12: ffff8801cc3f1dc8 R13: ffff8801cc3f1d40 R14: 0000000000001036 R15: dffffc0000000000 FS: 00007f43d740c700(0000) GS:ffff8801dc100000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7834984000 CR3: 00000001d79b9000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ip6_finish_skb include/net/ipv6.h:911 [inline] udp_v6_push_pending_frames+0x255/0x390 net/ipv6/udp.c:1093 udpv6_sendmsg+0x280d/0x31a0 net/ipv6/udp.c:1363 inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:762 sock_sendmsg_nosec net/socket.c:633 [inline] sock_sendmsg+0xca/0x110 net/socket.c:643 SYSC_sendto+0x352/0x5a0 net/socket.c:1750 SyS_sendto+0x40/0x50 net/socket.c:1718 entry_SYSCALL_64_fastpath+0x1f/0xbe RIP: 0033:0x4512e9 RSP: 002b:00007f43d740bc08 EFLAGS: 00000216 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00000000007180a8 RCX: 00000000004512e9 RDX: 000000000000002e RSI: 0000000020d08000 RDI: 0000000000000005 RBP: 0000000000000086 R08: 00000000209c1000 R09: 000000000000001c R10: 0000000000040800 R11: 0000000000000216 R12: 00000000004b9c69 R13: 00000000ffffffff R14: 0000000000000005 R15: 00000000202c2000 Code: 9e 01 fe e9 c5 e8 ff ff e8 7f 9e 01 fe e9 4a ea ff ff 48 89 f7 e8 52 9e 01 fe e9 aa eb ff ff e8 a8 b6 cf fd 0f 0b e8 a1 b6 cf fd <0f> 0b 49 8d 45 78 4d 8d 45 7c 48 89 85 78 fe ff ff 49 8d 85 ba RIP: __skb_pull include/linux/skbuff.h:2064 [inline] RSP: ffff8801ac6bf570 RIP: __ip6_make_skb+0x18cf/0x1f70 net/ipv6/ip6_output.c:1617 RSP: ffff8801ac6bf570 Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Mike Maloney <maloney@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15net: cs89x0: add MODULE_LICENSEArnd Bergmann
This driver lacks a MODULE_LICENSE tag, leading to a Kbuild warning: WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/cirrus/cs89x0.o This adds license, author, and description according to the comment block at the start of the file. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15ppp: unlock all_ppp_mutex before registering deviceGuillaume Nault
ppp_dev_uninit(), which is the .ndo_uninit() handler of PPP devices, needs to lock pn->all_ppp_mutex. Therefore we mustn't call register_netdevice() with pn->all_ppp_mutex already locked, or we'd deadlock in case register_netdevice() fails and calls .ndo_uninit(). Fortunately, we can unlock pn->all_ppp_mutex before calling register_netdevice(). This lock protects pn->units_idr, which isn't used in the device registration process. However, keeping pn->all_ppp_mutex locked during device registration did ensure that no device in transient state would be published in pn->units_idr. In practice, unlocking it before calling register_netdevice() doesn't change this property: ppp_unit_register() is called with 'ppp_mutex' locked and all searches done in pn->units_idr hold this lock too. Fixes: 8cb775bc0a34 ("ppp: fix device unregistration upon netns deletion") Reported-and-tested-by: syzbot+367889b9c9e279219175@syzkaller.appspotmail.com Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15ptr_ring: document usage around __ptr_ring_peekMichael S. Tsirkin
This explains why is the net usage of __ptr_ring_peek actually ok without locks. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-159p: add missing module license for xen transportStephen Hemminger
The 9P of Xen module is missing required license and module information. See https://bugzilla.kernel.org/show_bug.cgi?id=198109 Reported-by: Alan Bartlett <ajb@elrepo.org> Fixes: 868eb122739a ("xen/9pfs: introduce Xen 9pfs transport driver") Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15ring-buffer: Bring back context level recursive checksSteven Rostedt (VMware)
Commit 1a149d7d3f45 ("ring-buffer: Rewrite trace_recursive_(un)lock() to be simpler") replaced the context level recursion checks with a simple counter. This would prevent the ring buffer code from recursively calling itself more than the max number of contexts that exist (Normal, softirq, irq, nmi). But this change caused a lockup in a specific case, which was during suspend and resume using a global clock. Adding a stack dump to see where this occurred, the issue was in the trace global clock itself: trace_buffer_lock_reserve+0x1c/0x50 __trace_graph_entry+0x2d/0x90 trace_graph_entry+0xe8/0x200 prepare_ftrace_return+0x69/0xc0 ftrace_graph_caller+0x78/0xa8 queued_spin_lock_slowpath+0x5/0x1d0 trace_clock_global+0xb0/0xc0 ring_buffer_lock_reserve+0xf9/0x390 The function graph tracer traced queued_spin_lock_slowpath that was called by trace_clock_global. This pointed out that the trace_clock_global() is not reentrant, as it takes a spin lock. It depended on the ring buffer recursive lock from letting that happen. By removing the context detection and adding just a max number of allowable recursions, it allowed the trace_clock_global() to be entered again and try to retake the spinlock it already held, causing a deadlock. Fixes: 1a149d7d3f45 ("ring-buffer: Rewrite trace_recursive_(un)lock() to be simpler") Reported-by: David Weinehall <david.weinehall@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2018-01-15cfg80211: check dev_set_name() return valueJohannes Berg
syzbot reported a warning from rfkill_alloc(), and after a while I think that the reason is that it was doing fault injection and the dev_set_name() failed, leaving the name NULL, and we didn't check the return value and got to rfkill_alloc() with a NULL name. Since we really don't want a NULL name, we ought to check the return value. Fixes: fb28ad35906a ("net: struct device - replace bus_id with dev_name(), dev_set_name()") Reported-by: syzbot+1ddfb3357e1d7bb5b5d3@syzkaller.appspotmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-01-15mac80211_hwsim: validate number of different channelsJohannes Berg
When creating a new radio on the fly, hwsim allows this to be done with an arbitrary number of channels, but cfg80211 only supports a limited number of simultaneous channels, leading to a warning. Fix this by validating the number - this requires moving the define for the maximum out to a visible header file. Reported-by: syzbot+8dd9051ff19940290931@syzkaller.appspotmail.com Fixes: b59ec8dd4394 ("mac80211_hwsim: fix number of channels in interface combinations") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-01-15mac80211_hwsim: add workqueue to wait for deferred radio deletion on mod unloadBenjamin Beichler
When closing multiple wmediumd instances with many radios and try to unload the mac80211_hwsim module, it may happen that the work items live longer than the module. To wait especially for this deletion work items, add a work queue, otherwise flush_scheduled_work would be necessary. Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-19 14:40:05 +0000