| Age | Commit message (Collapse) | Author |
|---|
|
- Enable GPIO voltage for non pm modes as well so resetting
the default voltage works.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
- wait for vbl for both profile and dynpm
- unify profile and dynpm code paths more
- call pm_misc before of after clocks to make
sure voltage is changed in the proper order.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
r6xx+
The default power state does not always match the default clocks and voltage
for a particular card. The information in the firmware info table is correct
and should be used in preference to the info the default power state.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
I missed these in the r6xx commit.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
- This enables voltage adjustment on r6xx+ and certain
r5xx asics.
- Voltage drop support is already available for most
r1xx-r5xx asics.
V2: endian fix for voltage table.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Advanced validation is not implemented yet.
The mesa code that uses this will be released soon.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drm-testing
* 'nouveau/for-airlied' of ../drm-nouveau-next:
drm/nv50: cast IGP memory location to u64 before shifting
drm/nv50: use alternate source of SOR_MODE_CTRL for DP hack
drm/nouveau: fix dual-link displays when plugged into single-link outputs
drm/nv50: obey dcb->duallink_possible
drm/nv50: fix duallink_possible calculation for DCB 4.0 cards
drm/nouveau: don't execute INIT_GPIO unless we're really running the table
drm/nv40: allow cold-booting of nv4x chipsets
drm/nouveau: fix POST detection for certain chipsets
drm/nouveau: Add getparam for current PTIMER time.
drm/nouveau: allow cursor image and position to survive suspend
|
|
* drm-switcheroo-fixes:
drm/kms: disable/enable poll around switcheroo on/off
drm/nouveau: fixup confusion over which handle the DSM is hanging off.
drm/nouveau: attempt to get bios from ACPI v3
|
|
* drm-vmware-fixes:
drm/vmwgfx: Remove some leftover debug messages.
drm/vmwgfx: Print warnings in kernel log about bo pinning that fails.
drm/vmwgfx: Unpause overlay on update.
drm/vmwgfx: Some modesetting cleanups and fixes.
drm/vmwgfx: Don't use SVGA_REG_ENABLE in modesetting code.
drm/vmwgfx: Remove duplicate member from struct vmw_legacy_display_unit.
drm/vmwgfx: Reserve first part of VRAM for framebuffer.
drm/vmwgfx: Support older hardware.
drm/vmwgfx: Get connector status from detection function.
drm/vmwgfx: Add kernel throttling support. Bump minor.
drm/vmwgfx: Make sure to unpin old and pin new framebuffer.
drm/vmwgfx: Fix single framebuffer detection.
drm/vmwgfx: Assume larger framebuffer max size.
|
|
Because we aren't in a suspend state the poll will still run when we have switcherooed a card off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This fixes the DSM setup correctly since vga switcheroo.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Some of the laptops with the switchable graphics, seem to not post the secondary GPU at all, and we can't find a copy of the BIOS anywhere except in the ACPI rom retrieval.
This adds support for ACPI ROM retrieval to nouveau.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Fix a number of typos misspellings and checkpatch.pl warnings.
Replace "[ttm] " with TTM_PFX
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This patch fixes a regression introduced with the pool page allocator
in the event that there are no highmem pages (for example x86_64),
in which case cached page allocation would fail.
Tested with the vmwgfx driver on a 64-bit vm.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The unpause codepath uses vmw_overlay_update() so we must
unset the paused status.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We should not use SVGA_REG_ENABLE anywhere but in the fifo setup code,
since it controls whether the device is active.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The host may be touching this part of VRAM at modesetting,
even if we never use it ourselves, since we blit screen updates from 3D
surfaces. Make sure no DMA buffers are placed in this part of VRAM.
V2: Fix an error check in vmw_surface_dmabuf_pin().
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
V2: Fix a couple of typos.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Also make sure the ldu::active member is properly initialized.
Part of fix by Michel Daenzer <daenzer@vmware.com>.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Michel Daenzer <daenzer@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The throttle_us member in the execbuf argument is now honored.
If the member is 0, no waiting for lag will occur, which
guarantees backwards compatibility with well-behaved clients.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
V2: Fix a typo.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
airlied -> brown paper bag.
I blame Hi-5 or the Wiggles for lowering my IQ, move the fix inside some
brackets instead of breaking everything in site.
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes module unload+reload on Dell M4500, where the "normal" registers
get reset to 0.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
When selecting the native mode for a display we weren't taking into account
whether or not it was actually supported on that particular output.
This patch modifies our native mode selection to run all modes through
mode_valid() first.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
It was once assumed that all G8x had dual-link TMDS everywhere, this isn't
actually the case - especially considering passive DP->DVI converters and
some HDMI connectors only support single-link.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This resulted in accidently switching off the eDP panel on certain laptops
since the default state in the GPIO table was off.
Fixes rh#582621
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
We totally fail at detecting un-POSTed chipsets prior to G80. This commit
changes the pre-G80 POST detection to read the programmed horizontal total
from CRTC 0, and assume the card isn't POSTed if it's 0.
NVIDIA use some other heuristics more similar to what we do on G80, but I
wasted quite a long time trying to figure out the exact specifics of what
they do so we can try this for a bit instead.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This will be useful for computing GPU-CPU latency, including
GL_ARB_timer_query extension.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
- This isn't triggered yet on a normal kernel, because it still does a VT
switch, but it seemed like a good idea to fix this now.
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Switches will try to update the topology address and not correctly fix
up the checksum, so just let it slide.
https://bugs.freedesktop.org/28229
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
At least 'make CONFIG_DEBUG_SECTION_MISMATCH=y' causes
drivers/gpu/drm/radeon/atombios_crtc.c: In function 'atombios_crtc_set_pll':
drivers/gpu/drm/radeon/atombios_crtc.c:684: warning: 'pll' may be used uninitialized in this function
which has the looks of a falso positive.
Add a default: case so that gcc rests assured that all possible pll_id's are covered.
Keep the present cases that fall through to the default one for self-documentation.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drivers/gpu/drm/nouveau/nv40_graph.c: In function `nv40_graph_init':
drivers/gpu/drm/nouveau/nv40_graph.c:400: warning: the frame size of 1184 bytes is larger than 1024 bytes
drivers/gpu/drm/radeon/radeon_atombios.c: In function `radeon_get_atom_connector_info_from_supported_devices_table':
drivers/gpu/drm/radeon/radeon_atombios.c:857: warning: the frame size of 1872 bytes is larger than 1024 bytes
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When CONFIG_ACPI_BUTTON=m (and probably when ACPI_BUTTON is not enabled)
and NOUVEAU is built-in (not as a loadable module):
nouveau_connector.c:(.text+0xe17ce): undefined reference to `acpi_lid_open'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
I think it's good to release the AGP bridge at suspend
and reacquire it at resume. Also fix :
https://bugzilla.kernel.org/show_bug.cgi?id=15969
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This saves some more power at the expense of performance.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* nouveau/for-airlied:
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
drm/nv04: Implement missing nv04 PGRAPH methods in software.
drm/nouveau: Use 0x5f instead of 0x9f as imageblit on original NV10.
|
|
radeon needs power supply to get correct PM info so select it at the radeon
level not at the kms option.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
list reservation was too optimistic about ttm object reservation
and could think that an object reserved by some other process
as reserved by the list reservation which was false. Thus when
unreserving the list it might unreserve object that it didn't
reserved in the list. Sorry if it's hard to follow but this
kind of things are just causing headheck.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes AGP initialization failure with Apple UniNorth bridges due to trying to
ioremap() normal RAM.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Seems to cause issues with the sound hardware. Fixes kernel
bug 15982:
https://bugzilla.kernel.org/show_bug.cgi?id=15982
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Spotted by Scott Bertilson.
Fixes fdo bug 28146.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Mark Marshall <mark.marshall@csr.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
