| Age | Commit message (Collapse) | Author |
|---|
|
Currently, four reset types are supported for the HNS3 ethernet
driver: IMP reset, global reset, function reset, and FLR. Only
FLR can now be triggered by the user. To restore the device when
an exception occurs, add support for triggering reset by ethtool.
Run the "ethtool --reset DEVNAME mgmt | all | dedicated" to
trigger the IMP | global | function reset manually.
In addition, VF can only trigger function reset.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Link: https://lore.kernel.org/r/1628602128-15640-1-git-send-email-huangguangbin2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds skb's frag page recycling support based on
the frag page support in page pool.
The performance improves above 10~20% for single thread iperf
TCP flow with IOMMU disabled when iperf server and irq/NAPI
have a different CPU.
The performance improves about 135%(14Gbit to 33Gbit) for single
thread iperf TCP flow when IOMMU is in strict mode and iperf
server shares the same cpu with irq/NAPI.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicting commits, all resolutions pretty trivial:
drivers/bus/mhi/pci_generic.c
5c2c85315948 ("bus: mhi: pci-generic: configurable network interface MRU")
56f6f4c4eb2a ("bus: mhi: pci_generic: Apply no-op for wake using sideband wake boolean")
drivers/nfc/s3fwrn5/firmware.c
a0302ff5906a ("nfc: s3fwrn5: remove unnecessary label")
46573e3ab08f ("nfc: s3fwrn5: fix undefined parameter values in dev_err()")
801e541c79bb ("nfc: s3fwrn5: fix undefined parameter values in dev_err()")
MAINTAINERS
7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver")
8a7b46fa7902 ("MAINTAINERS: add Yasushi SHOJI as reviewer for the Microchip CAN BUS Analyzer Tool driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ptp cycle is related to the hardware, so it may cause compatibility
issues if a fixed value is used in driver. Therefore, the method of
obtaining this value is changed to read from the register rather than
use a fixed value in driver.
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink reload support for HNS3 ethernet VF driver.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink reload support for HNS3 ethernet PF driver.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink get info support for HNS3 ethernet VF driver.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink get info support for HNS3 ethernet PF driver.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink register support for HNS3 ethernet VF driver.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink register support for HNS3 ethernet PF driver.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, VF doesn't enable rx VLAN offload when initializating,
and PF does it for VFs. If user disable the rx VLAN offload for
VF with ethtool -K, and reload the VF driver, it may cause the
rx VLAN offload state being inconsistent between hardware and
software.
Fixes it by enabling rx VLAN offload when VF initializing.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
control
For hardware limitation, port VLAN filter is port level, and
effective for all the functions of the port. So if not support
port VLAN bypass, it's necessary to disable the port VLAN filter,
in order to support function level VLAN filter control.
Fixes: 2ba306627f59 ("net: hns3: add support for modify VLAN filter state")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When VF need response from PF, VF will wait (1us - 1s) to receive
the response, or it will wait timeout and the VF action fails.
If VF do not receive response in 1st action because timeout,
the 2nd action may receive response for the 1st action, and get
incorrect response data.VF must reciveve the right response from
PF,or it will cause unexpected error.
This patch adds match_id to check mailbox response from PF to VF,
to make sure VF get the right response:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
This scheme depends on PF driver supports match_id, if PF driver doesn't
support then VF will uses the original scheme.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the mailbox synchronous communication between VF and PF use
the following fields to maintain communication:
1. Origin_mbx_msg which was combined by message code and subcode, used
to match request and response.
2. Received_resp which means whether received response.
There may possible mismatches of the following situation:
1. VF sends message A with code=1 subcode=1.
2. PF was blocked about 500ms when processing the message A.
3. VF will detect message A timeout because it can't get the response
within 500ms.
4. VF sends message B with code=1 subcode=1 which equal message A.
5. PF processes the first message A and send the response message to
VF.
6. VF will identify the response matched the message B because the
code/subcode is the same. This will lead to mismatch of request and
response.
To fix the above bug, we use the following scheme:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
As for PF driver, it only needs to copy the match_id from request to
response.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.
../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
134 | #define CACHE_LINE_MASK 0x3F
In file included from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:19,
from ../include/linux/list.h:9,
from ../include/linux/module.h:12,
from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1))
Fixes: d413779cdd93 ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support of dumping MAC umv counter in debugfs,
which will be helpful for debugging.
The display style is below:
$ cat umv_info
num_alloc_vport : 2
max_umv_size : 256
wanted_umv_size : 256
priv_umv_size : 85
share_umv_size : 86
vport(0) used_umv_num : 1
vport(1) used_umv_num : 1
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, the flow director counter is not enabled. To improve the
maintainability for chechking whether flow director hit or not, enable
flow director counter for each function, and add debugfs query inerface
to query the counters for each function.
The debugfs command is below:
cat fd_counter
func_id hit_times
pf 0
vf0 0
vf1 0
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'hclge_handle_error_info_log()'
If this 'kzalloc()' fails we must free some resources as in all the other
error handling paths of this function.
Fixes: 2e2deee7618b ("net: hns3: add the RAS compatibility adaptation solution")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These flags are used to set and test bits like this:
if (!test_bit(HCLGE_PTP_FLAG_TX_EN, &ptp->flags) ||
The issue is that test_bit() takes a bit number like 1, but we are
passing BIT(1) instead and it's testing BIT(BIT(1)). This does not
cause a problem because it is always done consistently and the bit
values are very small.
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch doesn't affect runtime at all, it's just a correctness issue.
The ptp->info.name[] buffer has 16 characters but the snprintf() limit
was capped at 32 characters. Fortunately, HCLGE_DRIVER_NAME is "hclge"
which isn't close to 16 characters so we're fine.
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current rx page reuse handling process, the rx page buffer may
have conflict between driver and stack in high-pressure scenario.
To fix this problem, we need to check whether the page is only owned
by driver at the begin and at the end of a page to make sure there is
no reuse conflict between driver and stack when desc_cb->page_offset
is rollbacked to zero or increased.
Fixes: fa7711b888f2 ("net: hns3: optimize the rx page reuse handling process")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently rx page will be reused to receive future packet when
the stack releases the previous skb quickly. If the old page
can not be reused, a new page will be allocated and mapped,
which comsumes a lot of cpu when IOMMU is in the strict mode,
especially when the application and irq/NAPI happens to run on
the same cpu.
So allocate a new frag to memcpy the data to avoid the costly
IOMMU unmapping/mapping operation, and add "frag_alloc_err"
and "frag_alloc" stats in "ethtool -S ethX" cmd.
The throughput improves above 50% when running single thread of
iperf using TCP when IOMMU is in strict mode and iperf shares the
same cpu with irq/NAPI(rx_copybreak = 2048 and mtu = 1500).
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current rx page offset only reset to zero when all the below
conditions are satisfied:
1. rx page is only owned by driver.
2. rx page is reusable.
3. the page offset that is above to be given to the stack has
reached the end of the page.
If the page offset is over the hns3_buf_size(), it means the
buffer below the offset of the page is usable when the above
condition 1 & 2 are satisfied, so page offset can be reset to
zero instead of increasing the offset. We may be able to always
reuse the first 4K buffer of a 64K page, which means we can
limit the hot buffer size as much as possible.
The above optimization is a side effect when refacting the
rx page reuse handling in order to support the rx copybreak.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using the queue based tx buffer, it is also possible to allocate a
sgl buffer, and use skb_to_sgvec() to convert the skb to the sgvec
in order to support the dma_map_sg() to decreases the overhead of
IOMMU mapping and unmapping.
Firstly, it reduces the number of buffers. For example, a tcp skb
may have a 66-byte header and 3 fragments of 4328, 32768, and 28064
bytes. With this patch, dma_map_sg() will combine them into two
buffers, 66-bytes header and one 65160-bytes fragment by using IOMMU.
Secondly, it reduces the number of dma mapping and unmapping. All the
original 4 buffers are mapped only once rather than 4 times.
The throughput improves above 10% when running single thread of iperf
using TCP when IOMMU is in strict mode.
Suggested-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to query tx spare buffer size from configuration
file, and use this info to do spare buffer initialization when
the module parameter 'tx_spare_buf_size' is not specified.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when the packet or frag size is small, it causes both security and
performance issue. As dma can't map sub-page, this means some extra
kernel data is visible to devices. On the other hand, the overhead
of dma map and unmap is huge when IOMMU is on.
So add a queue based tx shared bounce buffer to memcpy the small
packet when the len of the xmitted skb is below tx_copybreak.
Add tx_spare_buf_size module param to set the size of tx spare
buffer, and add set/get_tunable to set or query the tx_copybreak.
The throughtput improves from 30 Gbps to 90+ Gbps when running 16
netperf threads with 32KB UDP message size when IOMMU is in the
strict mode(tx_copybreak = 2000 and mtu = 1500).
Suggested-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor out hns3_fill_desc() so that it can be reused in the
tx bounce supporting.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
desc_cb is used to store mapping and freeing info for the
corresponding desc, which is used in the cleaning process.
There will be more desc_cb type coming up when supporting the
tx bounce buffer, change desc_cb type to bit-wise value in order
to reduce the desc_cb type checking operation in the data path.
Also move the desc_cb type definition to hns3_enet.h because it
is only used in hns3_enet.c, and declare a local variable desc_cb
in hns3_clear_desc() to reduce lines of code.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a debugfs interface for dumping ptp information, which
is helpful for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds PTP support for HNS3 ethernet driver.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using list_move_tail() instead of list_del() + list_add_tail() in hclge_main.c.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hclgevf_main.c
Using list_move_tail() instead of list_del() + list_add_tail() in hclgevf_main.c.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During initialization, the driver logs and clears the hw errors that
already occurred. For device supports imp-handle ras capability, it
needs handle different error status, otherwise it may cause wrong reset.
So fix it by adding a new processing branch.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update error recovery module and type for RoCE.
The enumeration values of module names and error types are not sorted
in sequence. If use the current printing mode, they cannot be correctly
printed.
Use the index mode, If mod_id and type_id match the enumerated value,
display the corresponding information.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IMP(Intelligent Management Processor) firmware add a new feature to
handle and consolidate RAS information for new devices, NIC driver
only needs to query the reported RAS information. NIC driver adds
support for this feature.
Driver queries device capability to check whether IMP support this
feature, If yes, execute the new RAS processing branch.
In order to add a method to check whether PF supports imp-handle RAS
feature, add dumping this info in debugfs.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To adapt to hardware modification and ensure that the driver is
compatible with the original error handling content, we need to add the
RAS compatibility adaptation solution.
Add a processing branch to the driver during error handling. In the new
processing branch, NIC fault information is integrated by the IMP. An
interaction command is added between the driver and IMP to query
and clear the fault source and interrupt source. The IMP integrates
error information and reports the highest reset level to the driver.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, hardware errors can be reported through AER or MSI-X mode.
However, the AER mode is intended to handle only bus errors, but not
hardware errors. On the other hand, virtual machines cannot handle
AER errors. When an AER error is reported, virtual machines will be
suspended. So add support for handling all these hardware errors
through MSI-X mode which depends on a newer version of firmware,
and reserve the handler of the AER mode for compatibility.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Earlier patches have decoupled the MSI-X conveyed error handling
and recovery logic. This earlier concept code is no longer required.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error handling & recovery is done in context of reset task which
gets scheduled from misc interrupt handler in existing code. But
since error handling has been moved to new task, it should get
scheduled instead of the reset task from the interrupt handler.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error handling and recovery logic are intertwined. Error handling (i.e.
error identification, clearing error sources and initiation of recovery)
is done in context of reset task. If certain hardware errors get
delivered during driver init time, which can cause driver init/loading
to fail.
Introduce a separate error handling task to ensure below:
1. Reset logic remains independent of the error handling logic.
2. Add the hclge_errhand_task_schedule to schedule error recovery
tasks, This will ensure that common misellaneous MSI-X interrupt are
re-enabled quickly.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add debugfs support for vlan configuraion. create a single file
"vlan_config" for it, and query it by command "cat vlan_config",
return the result to userspace.
The new display style is below:
$ cat vlan_config
I_PORT_VLAN_FILTER: on
E_PORT_VLAN_FILTER: off
FUNC_ID I_VF_VLAN_FILTER E_VF_VLAN_FILTER PORT_VLAN_FILTER_BYPASS
pf off on off
vf0 off on off
FUNC_ID PVID ACCEPT_TAG1 ACCEPT_TAG2 ACCEPT_UNTAG1 ACCEPT_UNTAG2
pf 0 on on on on
vf0 0 on on on on
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, there is hardware limitation for VF to modify
the VLAN filter state, and the VLAN filter state is default
enabled. Now the limitation has been removed in some device,
so add capability flag to check whether the device supports
modify VLAN filter state. If flag on, user will be able to
modify the VLAN filter state by ethtool -K.
VF needs to send mailbox to request the PF to modify the VLAN
filter state for it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are some features of VF depend on PF, so it's necessary
for VF to know whether PF supports. For compatibility, modify
the mailbox HCLGE_MBX_GET_TCINFO, extend its function, use to
get the basic information of PF, including mailbox api version
and PF capabilities.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, with hardware limitation, the port VLAN filter are
effective for both PF and its VFs simultaneously, so a single
function is not able to enable/disable separately, and the VLAN
filter state is default enabled. Now some device supports each
function to bypass port VLAN filter, then each function can
switch VLAN filter separately. Add capability flag to check
whether the device supports modify VLAN filter state. If flag
on, user will be able to modify the VLAN filter state by ethtool
-K.
Furtherly, the default VLAN filter state is also changed
according to whether non-zero VLAN used. Then the device can
receive packet with any VLAN tag if only VLAN 0 used.
The function hclge_need_enable_vport_vlan_filter() is used to
help implement above changes. And the VLAN filter handle for
promisc mode can also be simplified by this function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The struct hclge_vf_vlan_cfg is firstly designed for setting
VLAN filter tag. And it's reused for enable RX VLAN offload
later. It's strange to use member "is_kill" to indicate "enable".
So redefine the struct hclge_vf_vlan_cfg to adapt it.
For there are already 3 subcodes being used in function
hclge_set_vf_vlan_cfg(), use "switch-case" style for each
branch, rather than "if-else". Also simplify the assignment for
each branch to make it more clearly.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For the PF have called hclge_update_port_base_vlan_cfg() already
before notify VF, it's unnecessary to update port based VLAN again
when received mailbox request from VF.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use struct "hclge_vlan_info" instead of separately parameters
for function hclge_push_vf_port_base_vlan_info(), to make it
more concise.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, option "qos" is igored by HNS3 driver for command
"ip link set ethx vf <vf id> vlan <vlan id> qos <qos value>".
Add support for it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
