| Age | Commit message (Collapse) | Author |
|---|
|
OTG3 and EH Compliance Plan 1.0 talks about Super Speed OTG Verification
system (SS-OVS) which consists of an excersizer and analyzer.
USB Compliance Suite from Lecroy or Ellisys can act as such SS-OVS for
Link Layer Validation (LVS).
Some modifications are needed for an embedded Linux USB host to pass all
these tests. Most of these tests require just Link to be in U0. They do
not work with default Linux USB stack since, default stack does port
reset and then starts sending setup packet, which is not expected by
Link Layer Validation (LVS) device of Lecroy Compliance Suit. Then,
There are many Link Layer Tests which need host to generate specific
traffic.
This patch supports specific traffic generation cases. As of now all the
host Lecroy Link Layer-USBIF tests (except TD7.26) passes
with this patch for single run using Lecroy USB Compliance Suite
Version 1.98 Build 239 and Lecroy USB Protocol Analyzer version 4.80
Build 1603. Therefore patch seems to be a good candidate for inclusion.
Further modification can be done on top of it.
lvstest driver will not bind to any device by default. It can bind
manually to a super speed USB host controller root hub. Therefore, regular
hub driver must be unbound before this driver is bound. For example, if
2-0:1.0 is the xhci root hub, then execute following to unbind hub driver.
echo 2-0:1.0 > /sys/bus/usb/drivers/hub/unbind
Then write Linux Foundation's vendor ID which is used by root hubs and
SS root hub's device ID into new_id file. Writing IDs into new_id file
will also bind the lvs driver with any available SS root hub interfaces.
echo "1D6B 3" > /sys/bus/usb/drivers/lvs/new_id
Now connect LVS device with root hub port.
Test case specific traffic can be generated as follows whenever needed:
1. To issue "Get Device descriptor" command for TD.7.06:
echo > /sys/bus/usb/devices/2-0\:1.0/get_dev_desc
2. To set U1 timeout to 127 for TD.7.18
echo 127 > /sys/bus/usb/devices/2-0\:1.0/u1_timeout
3. To set U2 timeout to 0 for TD.7.18
echo 0 > /sys/bus/usb/devices/2-0\:1.0/u2_timeout
4. To issue "Hot Reset" for TD.7.29
echo > /sys/bus/usb/devices/2-0\:1.0/hot_reset
5. To issue "U3 Entry" for TD.7.35
echo > /sys/bus/usb/devices/2-0\:1.0/u3_entry
6. To issue "U3 Exit" for TD.7.36
echo > /sys/bus/usb/devices/2-0\:1.0/u3_exit
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_alloc_dev is used by lvstest driver now which can be built as
module. Therefore export usb_alloc_dev symbol.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes a bug in ohci-hcd. When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule. Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed. If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.
This fails when a controller dies. A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it. The remaining URBs cannot be unlinked,
which causes the USB stack to hang.
The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running. This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The debug routine fill_async_buffer() in ohci-hcd is buggy: It never
produces any output because it forgets to initialize the output buffer
size. Also, the debug routine ohci_dump() has an unused argument.
This patch adds the correct initialization and removes the unused
argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Apparently nobody ever remembered to add Scatter-Gather support to
ohci-hcd. This patch adds it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a host controller dies, we don't need to wait for a driver to
time out. We can shut down its URBs immediately. Without this
change, we can end up waiting 30 seconds for a mass-storage transfer
to time out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v3.17-rc1
Here are some minor fixes and clean-ups to the ftdi_sio, mos7840 and kl5kusb105
drivers for v3.17-rc1.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
We want those fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds support for Infineon TriBoard TC1798 [1]. Only interface 1
is used as serial line (see [2], Figure 8-6).
[1] http://www.infineon.com/cms/de/product/microcontroller/development-tools-software-and-kits/tricore-tm-development-tools-software-and-kits/starterkits-and-evaluation-boards/starter-kit-tc1798/channel.html?channel=db3a304333b8a7ca0133cfa3d73e4268
[2] http://www.infineon.com/dgdl/TriBoardManual-TC1798-V10.pdf?folderId=db3a304412b407950112b409ae7c0343&fileId=db3a304333b8a7ca0133cfae99fe426a
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usb device will autoresume from choose_wakeup() if it is
autosuspended with the wrong wakeup setting, but below errors occur
because usb3503 misc driver will switch to standby mode when suspended.
As add USB_QUIRK_RESET_RESUME, it can stop setting wrong wakeup from
autosuspend_check().
[ 7.734717] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 7.854658] usb 1-3: device descriptor read/64, error -71
[ 8.079657] usb 1-3: device descriptor read/64, error -71
[ 8.294664] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 8.414658] usb 1-3: device descriptor read/64, error -71
[ 8.639657] usb 1-3: device descriptor read/64, error -71
[ 8.854667] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.264598] usb 1-3: device not accepting address 3, error -71
[ 9.374655] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.784601] usb 1-3: device not accepting address 3, error -71
[ 9.784838] usb usb1-port3: device 1-3 not suspended yet
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usb3503 needs to switch to standby mode while suspending and should
switch to hub mode when resumed. Also we can control clock on PM
function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch intoduces the use of devm_ioremap_resource instead of
request_mem_region and ioremap_nocache and removes the calls to free the
allocated memory. Some labels are removes and a new label failed
introduced to make it less specific to the context. The call to a
platform get resource with IORESOURCE_IO is removed as it allocates
memory that is not needed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch replaces the memory allocation using request_mem_region and
the ioremap by a single call to managed interface devm_ioremap_reource.
The corresponding calls to release_mem_region and iounmap in the probe
and release functions are now unnecessary and are removed. Also a label
is done away with and linux/device.h is added to make sure the devm_*()
outine declarations are unambiguously available.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds PID 0x0003 to the VID 0x128d (Testo). At least the
Testo 435-4 uses this, likely other gear as well.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tegra_usb_phy_close() is supposed to undo the effects of
tegra_usb_phy_init(). It is also currently added as the USB PHY shutdown
callback, which is wrong, since tegra_usb_phy_init() is only called
during probing wheras the shutdown callback can get called multiple
times. This then leads to warnings about unbalanced regulator_disable if
the EHCI driver is unbound and bound again at runtime.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Tegra USB complex has a particularly annoying misdesign: some of the
UTMI pad configuration registers are global for all the 3 USB controllers
on the chip, but those registers are located in the first controller's
register space and will be cleared when the reset to the first
controller is asserted. Currently, this means that if the 1st controller
were to finish probing after the 2nd or 3rd controller, USB would not
work at all.
Fix this situation by always resetting the 1st controller before doing
any other setup to any of the controllers, and then never ever reset the
first controller again. As the UTMI registers are related to the PHY,
the PHY driver should probably reset the Tegra controllers instead,
but since old device trees only have reset phandles in the EHCI nodes,
do it here, which means a bit of device tree groveling. Those old DTs
also won't get the reset fix from this commit, so we'll dev_warn() them,
but the driver will still keep probing successfully.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The various devm_ functions allocate memory that is released when a
driver detaches. This patch uses devm_ioremap_resource for data
that is allocated in the probe function of a platform device and
is only freed in the remove function. The corresponding free functions
are removed and two labels are done away with. Also, linux/device.h
is added to make sure the devm_*() routine declarations are
unambiguously available.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tegra_ehci_hcd structure is located in the private space allocated
by the core USB code so it must not be accessed after the HCD is
freed.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The EHCI packet buffer in/out threshold is programmable for Intel Quark X1000
USB host controller, and the default value is 0x20 dwords. The in/out threshold
can be programmed to 0x80 dwords (512 Bytes) to maximize the perfomrance,
but only when isochronous/interrupt transactions are not initiated by the USB
host controller. This patch is to reconfigure the packet buffer in/out
threshold as maximal as possible to maximize the performance, and 0x7F dwords
(508 Bytes) should be used because the USB host controller initiates
isochronous/interrupt transactions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@intel.com>
Signed-off-by: Alvin (Weike) Chen <alvin.chen@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
OHCI HCCA memory region is allocated from atomic DMA pool one time
during usb_add_hcd() and deallocated by usb_remove_hcd().
Do non-atomic allocation of OHCI HCCA and free some space in
coherent atomic DMA pool.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uhci_start() is executed one time during usb_add_hcd() call and by
default UHCI frame list is allocated from atomic DMA pool.
Do non-atomic allocation of uhci->frame and free some space in
coherent atomic DMA pool.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ehci_mem_init() is executed one time during ehci_init() and by default
all memory allocations but ehci->periodic are done not atomically,
GFP_KERNEL is passed as flags parameter.
Do similar allocation for ehci->periodic and free some space in
coherent atomic DMA pool by default.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes checkpatch warning:
"WARNING: debugfs_remove(NULL) is safe this check is probably not required"
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces the use of devm_ioremap_resource instead of
request_mem_region and ioremap. The error handling on
platform_get_resource and the error message for ioremap are removed. The
function devm_kzalloc replaces memory allocation by unmanaged kzalloc. The
function calls to free the allocated memory in the probe and remove
functions are done away with. Some labels are removed and a label error
is added to make is less specific to the context. The debug message is
removed as devm_ioremap generates debug messages of its own.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is no longer needed and keeping it will break 64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As far as kzalloc() is called with spinlock held,
we have to pass GFP_ATOMIC regardless of mem_flags argument.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Bit fields are not MP-safe.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The third argument of devm_of_phy_get expects a pointer.
Hence use NULL instead of 0. Fixes the following warning:
drivers/usb/host/ehci-exynos.c:91:51: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The third argument of devm_of_phy_get expects a pointer.
Hence use NULL instead of 0.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The file and folder movements resulted in the incorrect reference.
So for better code maintainability, let's remove it.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix checkpatch errors as belows.
ERROR: open brace '{' following function declarations go on the next line
ERROR: space required before the open parenthesis '('
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The R-Car H2 and M2 SoCs come with an xHCI controller that requires
some specific initializations related to the firmware downloading and
some specific registers. This patch adds the support for this special
configuration as an xHCI quirk executed during probe and start.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: "mathias.nyman@intel.com" <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces the use of managed interface devm_ioremap_resource
for ioremap_nocache and request_mem_region and removes the corresponding
free functions in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
grep must work, not matter the line length.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch remove the function klsi_105_tiocmset which was only
returning -EINVAL. It also removes the function prototype and
the .tiocmset entry in the struct usb_serial_driver.
Verified by compilation only.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resuming a powered down port sometimes results in the port state being
stuck in the training sequence.
hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0
port1: can't get reconnection after setting port power on, status -110
hub 3-0:1.0: port 1 status 0000.02e0 after resume, -19
usb 3-1: can't resume, status -19
hub 3-0:1.0: logical disconnect on port 1
In the case above we wait for the port re-connect timeout of 2 seconds
and observe that the port status is USB_SS_PORT_LS_POLLING (although it
is likely toggling between this state and USB_SS_PORT_LS_RX_DETECT).
This is indicative of a case where the device is failing to progress the
link training state machine.
It is resolved by issuing a warm reset to get the hub and device link
state machines back in sync.
hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0
usb usb3: port1 usb_port_runtime_resume requires warm reset
hub 3-0:1.0: port 1 not warm reset yet, waiting 50ms
usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
After a reconnect timeout when we expect the device to be present, force
a warm reset of the device. Note that we can not simply look at the
link status to determine if a warm reset is required as any of the
training states USB_SS_PORT_LS_POLLING, USB_SS_PORT_LS_RX_DETECT, or
USB_SS_PORT_LS_COMP_MOD are valid states that do not indicate the need
for warm reset by themselves.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Ksenia Ragiadakou <burzalodowa@gmail.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Sunil Joshi <joshi@samsung.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a USB device is disconnected, usb_unbind_interface is called, which
tries to enable and disable LPM. usb_enable_lpm also try to send a
control command SET SEL to the device.
Since device is already disconnected, therefore it does not make sense
to execute usb_(en/dis)able_lpm.
This patch returns from usb_(en/dis)able_lpm, if device was not in
default state atleast.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All dwc3 based xhci host controller supports USB3.0 LPM functionality.
Therefore enable it in platform data for all dwc3 based xhci device if
DWC3_HOST_USB3_LPM_ENABLE is selected in Kconfig.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If an xhci platform supports USB3 LPM capability then enable
XHCI_LPM_SUPPORT quirk flag.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To use auto U0-U1/U2 transition by xhci platform device add
(en/dis)able_usb3_lpm_timeout function to the xhci_plat_xhci_driver struct.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As best case, a host controller should support U0 to U1 switching for
the devices connected below any tier of hub level supported by usb
specification. Therefore xhci_check_tier_policy should always return
success as default implementation.
A host should be able to issue LGO_Ux after the timeout calculated as
per definition of system exit latency defined in C.1.5.2. Therefore
xhci_calculate_ux_timeout returns ux_params.sel as the default
implementation.
Use default calculation in absence of any vendor specific limitations.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
