| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix yet another piece of ACPI CPPC changes fallout on AMD platforms
(Mario Limonciello)"
* tag 'acpi-5.19-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: CPPC: Don't require flexible address space if X86_FEATURE_CPPC is supported
|
|
Pull block fix from Jens Axboe:
"Just a single fix for missing error propagation for an allocation
failure in raid5"
* tag 'block-5.19-2022-07-21' of git://git.kernel.dk/linux-block:
md/raid5: missing error code in setup_conf()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two driver bugfixes and a typo fix"
* tag 'i2c-for-5.19-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: cadence: Change large transfer count reset logic to be unconditional
i2c: imx: fix typo in comment
i2c: mlxcpld: Fix register setting for 400KHz frequency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix several regmap usage issues in gpio-pca953x
- fix out-of-tree build for GPIO selftests
- fix integer overflow in gpio-xilinx
* tag 'gpio-fixes-for-v5.19-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: gpio-xilinx: Fix integer overflow
selftests: gpio: fix include path to kernel headers for out of tree builds
gpio: pca953x: use the correct register address when regcache sync during init
gpio: pca953x: use the correct range when do regmap sync
gpio: pca953x: only use single read/write for No AI mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Only driver fixes:
- NULL check for the ralink and sunplus drivers
- Add Jacky Bai as maintainer for the Freescale pin controllers
- Fix pin config ops for the Ocelot LAN966x and SparX5
- Disallow AMD pin control to be a module: the GPIO lines need to be
active in early boot, so no can do
- Fix the Armada 37xx to use raw spinlocks in the interrupt handler
path to avoid wait context"
* tag 'pinctrl-v5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: armada-37xx: use raw spinlocks for regmap to avoid invalid wait context
pinctrl: armada-37xx: make irq_lock a raw spinlock to avoid invalid wait context
pinctrl: Don't allow PINCTRL_AMD to be a module
pinctrl: ocelot: Fix pincfg
pinctrl: ocelot: Fix pincfg for lan966x
MAINTAINERS: Update freescale pin controllers maintainer
pinctrl: sunplus: Add check for kcalloc
pinctrl: ralink: Check for null return of devm_kcalloc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
- sdhci-omap: Fix a lockdep warning while probing
* tag 'mmc-v5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-omap: Fix a lockdep warning for PM runtime init
|
|
Pull drm fixes from Dave Airlie:
"Fixes for this week.
The main one is the i915 firmware fix for the phoronix reported issue.
I've written some firmware guidelines as a result, should land in
-next soon. Otherwise a few amdgpu fixes, a scheduler fix, ttm fix and
two other minor ones.
scheduler:
- scheduling while atomic fix
ttm:
- locking fix
edp:
- variable typo fix
i915:
- add back support for v69 firmware on ADL-P
amdgpu:
- Drop redundant buffer cleanup that can lead to a segfault
- Add a bo_list mutex to avoid possible list corruption in CS
- dmub notification fix
imx:
- fix error path"
* tag 'drm-fixes-2022-07-22' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: Protect the amdgpu_bo_list list with a mutex v2
drm/imx/dcss: Add missing of_node_put() in fail path
drm/i915/guc: support v69 in parallel to v70
drm/i915/guc: Support programming the EU priority in the GuC descriptor
drm/panel-edp: Fix variable typo when saving hpd absent delay from DT
drm/amdgpu: Remove one duplicated ef removal
drm/ttm: fix locking in vmap/vunmap TTM GEM helpers
drm/scheduler: Don't kill jobs in interrupt context
drm/amd/display: Fix new dmub notification enabling in DM
|
|
Komeda driver relies on the generic DRM atomic helper functions to handle
commits. It only implements an atomic_commit_tail hook for the
mode_config_helper_funcs and even that one is pretty close to the generic
implementation with the exception of additional dma_fence signalling.
What the generic helper framework doesn't do is waiting for the actual
hardware to signal that the commit parameters have been written into the
appropriate registers. As we signal CRTC events only on the irq handlers,
we need to flush the configuration and wait for the hardware to respond.
Add the Komeda specific implementation for atomic_commit_hw_done() that
flushes and waits for flip done before calling drm_atomic_helper_commit_hw_done().
The fix was prompted by a patch from Carsten Haitzler where he was trying to
solve the same issue but in a different way that I think can lead to wrong
event signaling to userspace.
Reported-by: Carsten Haitzler <carsten.haitzler@arm.com>
Tested-by: Carsten Haitzler <carsten.haitzler@arm.com>
Reviewed-by: Carsten Haitzler <carsten.haitzler@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220722122139.288486-1-liviu.dudau@arm.com
|
|
If something has already set up the DPU before the komeda driver comes
up, it will fail to init because it was just writing to the SRST bit in
the GCU control register and ignoring others. This resulted in TBU
bringup stalling and init failing. By writing completely we also set the
mode back to 0 (inactive) too and thus TBU bringup works.
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220606114714.175499-2-carsten.haitzler@foss.arm.com
|
|
The komeda driver doesn't come up with a visible text (FB) mode VT by
default as it was missing legacy FB support. It's useful to have a
working text VT on a system for debug and general usability, so enable
it. You can always toggle CONFIG_FRAMEBUFFER_CONSOLE.
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220606114714.175499-1-carsten.haitzler@foss.arm.com
|
|
Since we no longer need to conform to the structure of the various DRM
IRQ callbacks, we can streamline the code by consolidating the piecemeal
functions and passing around our private data structure directly. We're
also a platform device so should never see IRQ_NOTCONNECTED either.
Furthermore we can also get rid of all the unnecesary read-modify-write
operations, since on install we know we cleared the whole interrupt mask
before enabling the debug IRQs, and thus on uninstall we're always
clearing everything as well.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/65cf7818b23c1a8629dc851f1d058ecb8a14849e.1655309413.git.robin.murphy@arm.com
|
|
The Arm Juno board EDK2 port has provided an EFI GOP display via HDLCD0
for some time now, which works nicely as an early framebuffer. However,
once the HDLCD driver probes and takes over the hardware, it should
take over the logical framebuffer as well, otherwise the now-defunct GOP
device hangs about and virtual console output inevitably disappears into
the wrong place most of the time.
We'll do this after binding the HDMI encoder, since that's the most
likely thing to fail, and the EFI console is still better than nothing
when that happens. However, the two HDLCD controllers on Juno are
independent, and many users will still be using older firmware without
any display support, so we'll only bother if we find that the HDLCD
we're probing is already enabled. And if it is, then we'll also stop it,
since otherwise the display can end up shifted if it's still scanning
out while the rest of the registers are subsequently reconfigured.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/31acd57f4aa8a4d02877026fa3a8c8d035e15a0d.1655309004.git.robin.murphy@arm.com
|
|
Fix spelling typo in comments.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: pengfuyuan <pengfuyuan@kylinos.cn>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426121639.39160-1-pengfuyuan@kylinos.cn
|
|
Current implementation is not able to configure more than 32 pins
due to incorrect data type. So type casting with unsigned long
to avoid it.
Fixes: 02b3f84d9080 ("xilinx: Switch to use bitmap APIs")
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Reverse the order of the final two arguments when calling
aperture_remove_conflicting_devices(). An error report is available
at [1].
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 8d69d008f44c ("fbdev: Convert drivers to aperture helpers")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com> # hypervfb
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-hyperv@vger.kernel.org
Link: https://lore.kernel.org/lkml/202207202040.jS1WcTzN-lkp@intel.com/ # 1
Link: https://patchwork.freedesktop.org/patch/msgid/20220721081655.16128-1-tzimmermann@suse.de
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
Driver uAPI changes:
- All related to the Small BAR support: (and all by Matt Auld)
* add probed_cpu_visible_size
* expose the avail memory region tracking
* apply ALLOC_GPU only by default
* add NEEDS_CPU_ACCESS hint
* tweak error capture on recoverable contexts
Driver highlights:
- Add Small BAR support (Matt)
- Add MeteorLake support (RK)
- Add support for LMEM PCIe resizable BAR (Akeem)
Driver important fixes:
- ttm related fixes (Matt Auld)
- Fix a performance regression related to waitboost (Chris)
- Fix GT resets (Chris)
Driver others:
- Adding GuC SLPC selftest (Vinay)
- Fix ADL-N GuC load (Daniele)
- Add platform workaround (Gustavo, Matt Roper)
- DG2 and ATS-M device ID updates (Matt Roper)
- Add VM_BIND doc rfc with uAPI documentation (Niranjana)
- Fix user-after-free in vma destruction (Thomas)
- Async flush of GuC log regions (Alan)
- Fixes in selftests (Chris, Dan, Andrzej)
- Convert to drm_dbg (Umesh)
- Disable OA sseu config param for newer hardware (Umesh)
- Multi-cast register steering changes (Matt Roper)
- Add lmem_bar_size modparam (Priyanka)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Ys85pcMYLkqF/HtB@intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
Short summary of fixes pull:
* amdgpu: Fix for drm buddy memory corruption
* nouveau: PM fixes; DP fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Ytj65+PdAJs4jIEO@linux-uq9g
|
|
Miscellaneous R-Car DU fixes and enhancements
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YtIEWkE0nk/8nhUc@pendragon.ideasonboard.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
A scheduling-while-atomic fix for drm/scheduler, a locking fix for TTM,
a typo fix for panel-edp and a resource removal fix for imx/dcss
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220721085550.hrwbukj34y56rzva@houat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fix from Richard Weinberger:
"A aingle NAND controller fix:
- gpmi: Fix busy timeout setting (wrong calculation, yes again)"
* tag 'mtd/fixes-for-5.19-final' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: gpmi: Set WAIT_FOR_READY timeout based on program/erase times
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can.
Still no major regressions, most of the changes are still due to data
races fixes, plus the usual bunch of drivers fixes.
Previous releases - regressions:
- tcp/udp: make early_demux back namespacified.
- dsa: fix issues with vlan_filtering_is_global
Previous releases - always broken:
- ip: fix data-races around ipv4_net_table (round 2, 3 & 4)
- amt: fix validation and synchronization bugs
- can: fix detection of mcp251863
- eth: iavf: fix handling of dummy receive descriptors
- eth: lan966x: fix issues with MAC table
- eth: stmmac: dwmac-mediatek: fix clock issue
Misc:
- dsa: update documentation"
* tag 'net-5.19-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (107 commits)
mlxsw: spectrum_router: Fix IPv4 nexthop gateway indication
net/sched: cls_api: Fix flow action initialization
tcp: Fix data-races around sysctl_tcp_max_reordering.
tcp: Fix a data-race around sysctl_tcp_abort_on_overflow.
tcp: Fix a data-race around sysctl_tcp_rfc1337.
tcp: Fix a data-race around sysctl_tcp_stdurg.
tcp: Fix a data-race around sysctl_tcp_retrans_collapse.
tcp: Fix data-races around sysctl_tcp_slow_start_after_idle.
tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts.
tcp: Fix data-races around sysctl_tcp_recovery.
tcp: Fix a data-race around sysctl_tcp_early_retrans.
tcp: Fix data-races around sysctl knobs related to SYN option.
udp: Fix a data-race around sysctl_udp_l3mdev_accept.
ip: Fix data-races around sysctl_ip_prot_sock.
ipv4: Fix data-races around sysctl_fib_multipath_hash_fields.
ipv4: Fix data-races around sysctl_fib_multipath_hash_policy.
ipv4: Fix a data-race around sysctl_fib_multipath_use_neigh.
can: rcar_canfd: Add missing of_node_put() in rcar_canfd_probe()
can: mcp251xfd: fix detection of mcp251863
Documentation: fix udp_wmem_min in ip-sysctl.rst
...
|
|
RSPI IP on RZ/{A, G2L} SoC's has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked.
PIO fallback does not work as interrupt signal is disabled.
This patch fixes this issue by re-enabling the interrupts by
calling dmaengine_synchronize().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220721143449.879257-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The datasheet says that VDD12 must be enabled and at full voltage before
VDD33 is enabled.
Reorder the bulk regulator supply names so that VDD12 is enabled before
VDD33. Any enable ramp delays should be handled by setting proper
constraints on the regulators.
Fixes: bc1aee7fc8f0 ("drm/bridge: Add I2C based driver for ps8640 bridge")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220721092258.3397461-1-wenst@chromium.org
|
|
On failure, these functions return error pointer, not NULL.
Signed-off-by: Liu Zixian <liuzixian4@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220718015357.1722-1-liuzixian4@huawei.com
|
|
Fix the double `wait' typo in comment.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220716040520.31676-1-wangborong@cdjrlc.com
|
|
The semicolon after the `}' is unneeded.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Removed line mention when pushing]
Link: https://patchwork.freedesktop.org/patch/msgid/20220716184439.72056-1-wangborong@cdjrlc.com
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.19-2022-07-20:
amdgpu:
- Drop redundant buffer cleanup that can lead to a segfault
- Add a bo_list mutex to avoid possible list corruption in CS
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720210917.6202-1-alexander.deucher@amd.com
|
|
A bunch of code was copy/pasted using pr_err as the default way to
report errors. However, drm_err is significantly more useful in
identifying where the error came from. So update the code to use that
instead.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220715004028.2126239-1-John.C.Harrison@Intel.com
|
|
Add panel identification entry for the AUO B120XAN01.0 (product ID:
0x1062) panel.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720191158.1590833-1-nfraprado@collabora.com
|
|
Add panel identification entry for the IVO R140NWF5 RH (product ID:
0x057d) panel.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220719203857.1488831-2-nfraprado@collabora.com
|
|
Protect the struct amdgpu_bo_list with a mutex. This is used during command
submission in order to avoid buffer object corruption as recorded in
the link below.
v2 (chk): Keep the mutex looked for the whole CS to avoid using the
list from multiple CS threads at the same time.
Suggested-by: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Cc: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2048
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
The amdgpu_dm file contains most of the code that works as an interface
between DRM API and DC. As a result, this file becomes very large since
it comprises multiple abstractions such as plane manipulation.
[How]
This commit extracts the plane code to its specific file named
amdgpu_dm_plane. This change does not change anything inside the
functions; the only exception is converting some static functions to a
global function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
In order to leverage igt tool to maintain mst feature, expose new
debugfs entry "mst_progress_status".
In our dm flow, record down the result of each phase of mst and user
can examine the mst result by checking whether each phase get completed
successfully.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Add "is_mst_connector" debugfs entry to help distinguish whether
a connector is in a mst topology or not.
Access it with the following command:
cat /sys/kernel/debug/dri/0/DP-X/is_mst_connector
Result:
- "root" stands for the root connector of the topology
- "branch" stands for branch device of the topology
- "end" stands for leaf node connector of the topology
- "no" stands for the connector is not a device of a mst topology
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Correct few problems below to have debugfs trigger_hotplug entry
supports mst case
* Adjust the place for acquiring the hpd_lock. We'll also access
dc_link when simulate unplug
* When detect the connector is a mst root, call
reset_cur_dp_mst_topology() to simulate unplug
* Don't support hotplug caused by CSN message since we can't change
mst topology info directly. We can't simulate that
* Clean up redundant code
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Need to leverage this function out of dc_link.c. Change it to public.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update DML to configure drr_display in vba struct.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Remove an unused variable "remove_disconnect_edp" which was a workaround
bit.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When CONFIG_DRM_AMD_SECURE_DISPLAY is enabled, it will try
to register vertical interrupt 0 for specific task.
Currently, only dcn10 have defined relevant info for vertical interrupt
0. If we enable CONFIG_DRM_AMD_SECURE_DISPLAY for other dcn ASIC, will
get DC_IRQ_SOURCE_INVALID while calling dc_interrupt_to_irq_source() and
cause pointer errors.
[How]
Add support of vertical interrupt 0 for all dcn ASIC.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
enable gfx ulv and gpo on smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Turn previously global function into a static function as it is not used
outside the file.
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On the dce_v6_0 and dce_v8_0 hpd tear down callback, the tmp variable
should be written into the control register instead of 0.
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The scratch register should be accessed through MMIO instead of RLCG
in SRIOV, since it being used in RLCG register access function.
Fixes: d54762cc3e6a ("drm/amdgpu: nuke dynamic gfx scratch reg allocation")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Gavin Wan <Gavin.Wan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
TTM used to track the "acc_size" of all BOs internally. We needed to
keep track of it in our memory reservation to avoid TTM running out
of memory in its own accounting. However, that "acc_size" accounting
has since been removed from TTM. Therefore we don't really need to
track it any more.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Philip Yang <philip.yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Protect the struct amdgpu_bo_list with a mutex. This is used during command
submission in order to avoid buffer object corruption as recorded in
the link below.
v2 (chk): Keep the mutex looked for the whole CS to avoid using the
list from multiple CS threads at the same time.
Suggested-by: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Cc: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2048
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix SPI NO Slave Select macro definition, when all the SPI CS bits
are high which means no slave is selected.
Fixes: 21b511ddee09 ("spi: spi-cadence: Fix SPI CS gets toggling sporadically")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220713164529.28444-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The following warning was seen:
WARNING: CPU: 0 PID: 0 at arch/x86/kernel/alternative.c:557 apply_returns (arch/x86/kernel/alternative.c:557 (discriminator 1))
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.19.0-rc4-00008-gee88d363d156 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-debian-1.16.0-4 04/01/2014
RIP: 0010:apply_returns (arch/x86/kernel/alternative.c:557 (discriminator 1))
Code: ff ff 74 cb 48 83 c5 04 49 39 ee 0f 87 81 fe ff ff e9 22 ff ff ff 0f 0b 48 83 c5 04 49 39 ee 0f 87 6d fe ff ff e9 0e ff ff ff <0f> 0b 48 83 c5 04 49 39 ee 0f 87 59 fe ff ff e9 fa fe ff ff 48 89
The warning happened when apply_returns() failed to convert "JMP
__x86_return_thunk" to RET. It was instead a JMP to nowhere, due to the
thunk relocation not getting resolved.
That rodata.o code is objcopy'd to .rodata, and later memcpy'd, so
relocations don't work (and are apparently silently ignored).
LKDTM is only used for testing, so the naked RET should be fine. So
just disable return thunks for that file.
While at it, disable objtool and KCSAN for the file.
Fixes: 0b53c374b9ef ("x86/retpoline: Use -mfunction-return")
Reported-by: kernel test robot <oliver.sang@intel.com>
Debugged-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/lkml/Ys58BxHxoDZ7rfpr@xsang-OptiPlex-9020/
|
|
transfers
In case a IRQ based transfer times out the bcm2835_spi_handle_err()
function is called. Since commit 1513ceee70f2 ("spi: bcm2835: Drop
dma_pending flag") the TX and RX DMA transfers are unconditionally
canceled, leading to NULL pointer derefs if ctlr->dma_tx or
ctlr->dma_rx are not set.
Fix the NULL pointer deref by checking that ctlr->dma_tx and
ctlr->dma_rx are valid pointers before accessing them.
Fixes: 1513ceee70f2 ("spi: bcm2835: Drop dma_pending flag")
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220719072234.2782764-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
this is a pull request of 2 patches for net/master.
The first patch is by me and fixes the detection of the mcp251863 in
the mcp251xfd driver.
The last patch is by Liang He and adds a missing of_node_put() in the
rcar_canfd driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlxsw needs to distinguish nexthops with a gateway from connected
nexthops in order to write the former to the adjacency table of the
device. The check used to rely on the fact that nexthops with a gateway
have a 'link' scope whereas connected nexthops have a 'host' scope. This
is no longer correct after commit 747c14307214 ("ip: fix dflt addr
selection for connected nexthop").
Fix that by instead checking the address family of the gateway IP. This
is a more direct way and also consistent with the IPv6 counterpart in
mlxsw_sp_rt6_is_gateway().
Cc: stable@vger.kernel.org
Fixes: 747c14307214 ("ip: fix dflt addr selection for connected nexthop")
Fixes: 597cfe4fc339 ("nexthop: Add support for IPv4 nexthops")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
