| Age | Commit message (Collapse) | Author |
|---|
|
This new ioctl pair allows two ppp channels to be bridged together:
frames arriving in one channel are transmitted in the other channel
and vice versa.
The practical use for this is primarily to support the L2TP Access
Concentrator use-case. The end-user session is presented as a ppp
channel (typically PPPoE, although it could be e.g. PPPoA, or even PPP
over a serial link) and is switched into a PPPoL2TP session for
transmission to the LNS. At the LNS the PPP session is terminated in
the ISP's network.
When a PPP channel is bridged to another it takes a reference on the
other's struct ppp_file. This reference is dropped when the channels
are unbridged, which can occur either explicitly on userspace calling
the PPPIOCUNBRIDGECHAN ioctl, or implicitly when either channel in the
bridge is unregistered.
In order to implement the channel bridge, struct channel is extended
with a new field, 'bridge', which points to the other struct channel
making up the bridge.
This pointer is RCU protected to avoid adding another lock to the data
path.
To guard against concurrent writes to the pointer, the existing struct
channel lock 'upl' coverage is extended rather than adding a new lock.
The 'upl' lock is used to protect the existing unit pointer. Since the
bridge effectively replaces the unit (they're mutually exclusive for a
channel) it makes coding easier to use the same lock to cover them
both.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 0a4e9ce17ba77847e5a9f87eed3c0ba46e3f82eb.
The code was developed and tested on an MSC313E SoC, which seems to be
half-way between the AT91RM9200 and the AT91SAM9260 in that it supports
both the 2-descriptors mode and a Tx ring.
It turns out that after the code was merged I could notice that the
controller would sometimes lock up, and only when dealing with sustained
bidirectional transfers, in which case it would report a Tx overrun
condition right after having reported being ready, and will stop sending
even after the status is cleared (a down/up cycle fixes it though).
After adding lots of traces I couldn't spot a sequence pattern allowing
to predict that this situation would happen. The chip comes with no
documentation and other bits are often reported with no conclusive
pattern either.
It is possible that my change is wrong just like it is possible that
the controller on the chip is bogus or at least unpredictable based on
existing docs from other chips. I do not have an RM9200 at hand to test
at the moment and a few tests run on a more recent 9G20 indicate that
this code path cannot be used there to test the code on a 3rd platform.
Since the MSC313E works fine in the single-descriptor mode, and that
people using the old RM9200 very likely favor stability over performance,
better revert this patch until we can test it on the original platform
this part of the driver was written for. Note that the reverted patch
was actually tested on MSC313E.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Daniel Palmer <daniel@0x0f.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/netdev/20201206092041.GA10646@1wt.eu/
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets sent by rmnet to the real device have variable MAP header
lengths based on the data format configured. This patch adds checks
to ensure that the real device MTU is sufficient to transmit the MAP
packet comprising of the MAP header and the IP packet. This check
is enforced when rmnet devices are created and updated and during
MTU updates of both the rmnet and real device.
Additionally, rmnet devices now have a default MTU configured which
accounts for the real device MTU and the headroom based on the data
format.
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Tested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(dis)connected
When the upper layer instruct us to connect (or disconnect), but we have
already connected (or disconnected), consider this operation successful
rather than failed.
This can help the upper layer to correct its record about whether we are
connected or not here in layer 2.
The upper layer may not have the correct information about whether we are
connected or not. This can happen if this driver has already been running
for some time when the "x25" module gets loaded.
Another X.25 driver (hdlc_x25) is already doing this, so we make this
driver do this, too.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new device ID for the next step of the silicon and
reflect the I226_K part.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2020-12-10
here's a pull request of 7 patches for net-next/master.
The first patch is by Oliver Hartkopp for the CAN ISOTP, which adds support for
functional addressing.
A patch by Antonio Quartulli removes an unneeded unlikely() annotation from the
rx-offload helper.
The next three patches target the m_can driver. Sean Nyekjaers's patch removes
a double clearing of clock stop request bit, Patrik Flykt's patch moves the
runtime PM enable/disable to m_can_platform and Jarkko Nikula's patch adds a
PCI glue code driver.
Fabio Estevam's patch converts the flexcan driver to DT only.
And Manivannan Sadhasivam's patchd for the mcp251xfd driver adds internal
loopback mode support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The definition of IS_ERR() already applies the unlikely() notation
when checking the error status of the passed pointer. For this
reason there is no need to have the same notation outside of
IS_ERR() itself.
Clean up code by removing redundant notation.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MCP251xFD supports internal loopback mode which can be used to verify CAN
functionality in the absence of a real CAN device.
Link: https://lore.kernel.org/r/20201201054019.11012-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mkl: mcp251xfd_get_normal_mode(): move CAN_CTRLMODE_LOOPBACK check to front]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The flexcan driver runs only on DT platforms, so simplify the code by using
of_device_get_match_data() to retrieve the driver data and also by removing the
unused id_table.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201128132855.7724-1-festevam@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for M_CAN controller on Intel Elkhart Lake attached to the PCI bus.
It integrates the Bosch M_CAN controller with Message RAM and the wrapper IP
block with additional registers which all of them are within the same MMIO
range.
Currently only interrupt control register from wrapper IP is used and the MRAM
configuration is expected to come from the firmware via "bosch,mram-cfg" device
property and parsed by m_can.c core.
Initial implementation is done by Felipe Balbi while he was working at Intel
with later changes from Raymond Tan and me.
Co-developed-by: Felipe Balbi (Intel) <balbi@kernel.org>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Felipe Balbi (Intel) <balbi@kernel.org>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20201117160827.3636264-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a preparatory patch for upcoming PCI based M_CAN devices. The current
PM implementation would cause PCI based drivers to enable PM twice, once when
the PCI device is added and a second time in m_can_class_register(). This will
cause 'Unbalanced pm_runtime_enable!' to be logged, and is a situation that
should be avoided.
Therefore, in anticipation of PCI devices, move PM enabling out from M_CAN
class registration to its only user, the m_can_platform driver.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Link: https://lore.kernel.org/r/20201023115800.46538-2-patrik.flykt@linux.intel.com
[mkl: m_can_plat_probe(): fix error handling
m_can_class_register(): simplify error handling]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
request bit
The CSR bit is already cleared when arriving here so remove this section of
duplicate code.
The registers set in m_can_config_endisable() is set to same exact values as
before this patch.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20191211063227.84259-1-sean@geanix.com
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
notation when using IS_ERR()
The definition of IS_ERR() already applies the unlikely() notation when
checking the error status of the passed pointer. For this reason there is no
need to have the same notation outside of IS_ERR() itself.
Clean up code by removing redundant notation.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Link: https://lore.kernel.org/r/20201210085321.18693-1-a@unstable.cc
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
For the max rss size of PF may be up to 512, the max queue
number of single tc may be up to 512 too. For the total queue
numbers may be up to 1280, so the queue offset of each tc may
be more than 1024. So adjust the rss tc mode configuration
command, including extend tc size field from 10 bits to 11
bits, and extend tc size field from 3 bits to 4 bits.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the max rss size of PF may be up to 512, so adjust the
command of configuring rss indirection table to support
queue id larger than 255. The width of queue id is extended
from 8 bits to 10 bits. The high 2 bits are stored in filed
rss_qid_h when the queue id is larger than 255.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the driver gets the max rss size from configuration
file when initialization. Both the PF and VF share the same
max rss size, and no more than 128.
For DEVICE_VERSION_V3, the max rss size for PF can be up to
512, so there is a new field in configuration file to store it,
the old filed is used for VF.
To be compatible with boards using old configure file, the PF
will use the old filed if the one is zero.
For the rss size may be larger than 256, so the type of
rss_indirection_tbl of struct hclge_vport should be changed to
u16 as well.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some new device supports forwarding packet to queues of specified
TC when flow director rule hit. So add support to configure flow
director rule by tc flower. To avoid rule conflict, add a new flow
director mode HCLGE_FD_TC_FLOWER_ACTIVE, and only one mode can be
active at the same time.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flow director rule hit
For some new device, it supports forwarding packet to queues
of specified TC when flow director rule hit. So extend the
command handle to support it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the HNS3 driver only supports offload for tc number
and prio_tc. This patch adds support for other qopts, including
queues count and offset for each tc.
When enable tc mqprio offload, it's not allowed to change
queue numbers by ethtool. For hardware limitation, the queue
number of each tc should be power of 2.
For the queues is not assigned to each tc by average, so it's
should return vport->alloc_tqps for hclge_get_max_channels().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, there are multiple members related to tc information
in struct hnae3_knic_private_info. Merge them into a new struct
hnae3_tc_info.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test robot reports:
drivers/net/ethernet/netronome/nfp/crypto/tls.c: In function 'nfp_net_tls_rx_resync_req':
drivers/net/ethernet/netronome/nfp/crypto/tls.c:477:18: warning: variable 'ipv6h' set but not used [-Wunused-but-set-variable]
477 | struct ipv6hdr *ipv6h;
| ^~~~~
In file included from include/linux/compiler_types.h:65,
from <command-line>:
drivers/net/ethernet/netronome/nfp/crypto/tls.c: In function 'nfp_net_tls_add':
include/linux/compiler_attributes.h:208:41: warning: statement will never be executed [-Wswitch-unreachable]
208 | # define fallthrough __attribute__((__fallthrough__))
| ^~~~~~~~~~~~~
drivers/net/ethernet/netronome/nfp/crypto/tls.c:299:3: note: in expansion of macro 'fallthrough'
299 | fallthrough;
| ^~~~~~~~~~~
Use the IPv6 header in the switch, it doesn't matter which header
we use to read the version field.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Assign stmmac's mdio_bus probe capabilities to MDIOBUS_C22_C45.
This extended the probing of C45 PHY devices on the MDIO bus.
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not check the encoding when deriving 1000BASE-X from the bitrate
when no other modes are discovered. Some GPON modules (VSOL V2801F
and CarlitoxxPro CPGOS03-0490 v2.0) indicate NRZ encoding with a
1200Mbaud bitrate, but should be driven with 1000BASE-X on the host
side.
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a workaround for the detection of VSOL V2801F / CarlitoxxPro
CPGOS03-0490 v2.0 GPON module which CarlitoxxPro states needs single
byte I2C reads to the EEPROM.
Pali Rohár reports that he also has a CarlitoxxPro-based V2801F module,
which reports a manufacturer of "OEM". This manufacturer can't be
matched as it appears in many different modules, so also match the part
number too.
Reported-by: Thomas Schreiber <tschreibe@gmail.com>
Reported-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. In x25_xmit, skb_reset_network_header is not necessary before we call
lapb_data_request. The lapb module doesn't need skb->network_header.
So there is no need to set skb->network_header before calling
lapb_data_request.
2. In x25_data_indication (called by the lapb module after data have
been received), skb_reset_network_header is not necessary before we
call netif_rx. After we call netif_rx, the code in net/core/dev.c will
call skb_reset_network_header before handing the skb to upper layers
(in __netif_receive_skb_core, called by __netif_receive_skb_one_core,
called by __netif_receive_skb, called by process_backlog). So we don't
need to call skb_reset_network_header by ourselves.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
partial success
We observed that in the error case for batched send_subcrq_indirect() the
driver does not account for the partial success case. This caused Linux to
crash when free_map and pool index are inconsistent.
Driver needs to update the rx pools "available" count when some batched
sends worked but an error was encountered as part of the whole operation.
Also track replenish_add_buff_failure for statistic purposes.
Fixes: 4f0b6812e9b9a ("ibmvnic: Introduce batched RX buffer descriptor transmission")
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2020-12-09
This series contains updates to ice driver only.
Bruce changes the allocation of ice_flow_prof_params from stack to heap to
avoid excessive stack usage. Corrects a misleading comment and silences a
sparse warning that is not a problem.
Paul allows for HW initialization to continue if PHY abilities cannot
be obtained.
Jeb removes bypassing FW link override and reading Option ROM and
netlist information for non-E810 devices as this is now available on
other devices.
Nick removes vlan_ena field as this information can be gathered by
checking num_vlan.
Jake combines format strings and debug prints to the same line.
Simon adds a space to fix string concatenation.
v4: Drop ACL patches. Change PHY abilities failure message from debug to
warning.
v3: Fix email address for DaveM and fix character in cover letter
v2: Expand on commit message for patch 3 to show example usage/commands.
Reduce number of defensive checks being done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the flexible control of interrupt trigger type, remove the hard coded
interrupt trigger type in the i2c module. The trigger type will be loaded
from a dts.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
