1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
|
CS35L36 Speaker Amplifier
Required properties:
- compatible : "cirrus,cs35l36"
- reg : the I2C address of the device for I2C
- VA-supply, VP-supply : power supplies for the device,
as covered in
Documentation/devicetree/bindings/regulator/regulator.txt.
- cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
converter's output voltage in mV. The range is from 2550mV to 12000mV with
increments of 50mV.
(Default) VP
- cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
Configures the peak current by monitoring the current through the boost FET.
Range starts at 1600mA and goes to a maximum of 4500mA with increments of
50mA.
(Default) 4.50 Amps
- cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
Seeds the digital boost converter's inductor estimation block with the initial
inductance value to reference.
1000 = 1uH (Default)
1200 = 1.2uH
Optional properties:
- cirrus,multi-amp-mode : Boolean to determine if there are more than
one amplifier in the system. If more than one it is best to Hi-Z the ASP
port to prevent bus contention on the output signal
- cirrus,boost-ctl-select : Boost conerter control source selection.
Selects the source of the BST_CTL target VBST voltage for the boost
converter to generate.
0x00 - Control Port Value
0x01 - Class H Tracking (Default)
0x10 - MultiDevice Sync Value
- cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming
PCM data
- cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the
polarity of outbound IMON feedback data
- cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the
polarity of outbound VMON feedback data
- cirrus,dcm-mode-enable : Boost converter automatic DCM Mode enable.
This enables the digital boost converter to operate in a low power
(Discontinuous Conduction) mode during low loading conditions.
- cirrus,weak-fet-disable : Boolean : The strength of the output drivers is
reduced when operating in a Weak-FET Drive Mode and must not be used to drive
a large load.
- cirrus,classh-wk-fet-delay : Weak-FET entry delay. Controls the delay
(in ms) before the Class H algorithm switches to the weak-FET voltage
(after the audio falls and remains below the value specified in WKFET_AMP_THLD).
0 = 0ms
1 = 5ms
2 = 10ms
3 = 50ms
4 = 100ms (Default)
5 = 200ms
6 = 500ms
7 = 1000ms
- cirrus,classh-weak-fet-thld-millivolt : Weak-FET amplifier drive threshold.
Configures the signal threshold at which the PWM output stage enters
weak-FET operation. The range is 50mV to 700mV in 50mV increments.
- cirrus,temp-warn-threshold : Amplifier overtemperature warning threshold.
Configures the threshold at which the overtemperature warning condition occurs.
When the threshold is met, the overtemperature warning attenuation is applied
and the TEMP_WARN_EINT interrupt status bit is set.
If TEMP_WARN_MASK = 0, INTb is asserted.
0 = 105C
1 = 115C
2 = 125C (Default)
3 = 135C
- cirrus,irq-drive-select : Selects the driver type of the selected interrupt
output.
0 = Open-drain
1 = Push-pull (Default)
- cirrus,irq-gpio-select : Selects the pin to serve as the programmable
interrupt output.
0 = PDM_DATA / SWIRE_SD / INT (Default)
1 = GPIO
Optional properties for the "cirrus,vpbr-config" Sub-node
- cirrus,vpbr-en : VBST brownout prevention enable. Configures whether the
VBST brownout prevention algorithm is enabled or disabled.
0 = VBST brownout prevention disabled (default)
1 = VBST brownout prevention enabled
See Section 7.31.1 VPBR Config for configuration options & further details
- cirrus,vpbr-thld : Initial VPBR threshold. Configures the VP brownout
threshold voltage
- cirrus,cirrus,vpbr-atk-rate : Attenuation attack step rate. Configures the
amount delay between consecutive volume attenuation steps when a brownout
condition is present and the VP brownout condition is in an attacking state.
- cirrus,vpbr-atk-vol : VP brownout prevention step size. Configures the VP
brownout prevention attacking attenuation step size when operating in either
digital volume or analog gain modes.
- cirrus,vpbr-max-attn : Maximum attenuation that the VP brownout prevention
can apply to the audio signal.
- cirrus,vpbr-wait : Configures the delay time between a brownout condition
no longer being present and the VP brownout prevention entering an attenuation
release state.
- cirrus,vpbr-rel-rate : Attenuation release step rate. Configures the delay
between consecutive volume attenuation release steps when a brownout condition
is not longer present and the VP brownout is in an attenuation release state.
- cirrus,vpbr-mute-en : During the attack state, if the vpbr-max-attn value
is reached, the error condition still remains, and this bit is set, the audio
is muted.
Example:
cs35l36: cs35l36@40 {
compatible = "cirrus,cs35l36";
reg = <0x40>;
VA-supply = <&dummy_vreg>;
VP-supply = <&dummy_vreg>;
reset-gpios = <&gpio0 54 0>;
interrupt-parent = <&gpio8>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
cirrus,boost-ind-nanohenry = <1000>;
cirrus,boost-ctl-millivolt = <10000>;
cirrus,boost-peak-milliamp = <4500>;
cirrus,boost-ctl-select = <0x00>;
cirrus,weak-fet-delay = <0x04>;
cirrus,weak-fet-thld = <0x01>;
cirrus,temp-warn-threshold = <0x01>;
cirrus,multi-amp-mode;
cirrus,irq-drive-select = <0x01>;
cirrus,irq-gpio-select = <0x01>;
cirrus,vpbr-config {
cirrus,vpbr-en = <0x00>;
cirrus,vpbr-thld = <0x05>;
cirrus,vpbr-atk-rate = <0x02>;
cirrus,vpbr-atk-vol = <0x01>;
cirrus,vpbr-max-attn = <0x09>;
cirrus,vpbr-wait = <0x01>;
cirrus,vpbr-rel-rate = <0x05>;
cirrus,vpbr-mute-en = <0x00>;
};
};
|
