omap: Make uncompress code and DEBUG_LL code generic

Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.

Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 65 insertions, 7 deletions

diff --git a/arch/arm/mach-omap1/include/mach/debug-macro.S b/arch/arm/mach-omap1/include/mach/debug-macro.S
index 9ea12f29e0b..b6d9584544b 100644
--- a/arch/arm/mach-omap1/include/mach/debug-macro.S
+++ b/arch/arm/mach-omap1/include/mach/debug-macro.S
@@ -15,18 +15,76 @@
 
 #include <plat/serial.h>
 
+		.pushsection .data
+omap_uart_phys:	.word	0x0
+omap_uart_virt:	.word	0x0
+		.popsection
+
+		/*
+		 * Note that this code won't work if the bootloader passes
+		 * a wrong machine ID number in r1. To debug, just hardcode
+		 * the desired UART phys and virt addresses temporarily into
+		 * the omap_uart_phys and omap_uart_virt above.
+		 */
 		.macro	addruart, rx, tmp
+
+		/* Use omap_uart_phys/virt if already configured */
+9:		mrc	p15, 0, \rx, c1, c0
+		tst	\rx, #1			@ MMU enabled?
+		ldreq	\rx, =omap_uart_phys	@ physical base address
+		ldrne	\rx, =omap_uart_virt	@ virtual base
+		ldr	\rx, [\rx, #0]
+		cmp	\rx, #0			@ is port configured?
+		bne	99f			@ already configured
+
+		/* Check 7XX UART1 scratchpad register for uart to use */
+		mrc	p15, 0, \rx, c1, c0
+		tst	\rx, #1			@ MMU enabled?
+		moveq	\rx, #0xff000000	@ physical base address
+		movne	\rx, #0xfe000000	@ virtual base
+		orr	\rx, \rx, #0x00fb0000	@ OMAP1UART1
+		ldrb	\rx, [\rx, #(UART_SCR << OMAP7XX_PORT_SHIFT)]
+		cmp	\rx, #0			@ anything in 7XX scratchpad?
+		bne	10f			@ found 7XX uart
+
+		/* Check 15xx/16xx UART1 scratchpad register for uart to use */
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
 		moveq	\rx, #0xff000000	@ physical base address
 		movne	\rx, #0xfe000000	@ virtual base
-		orr	\rx, \rx, #0x00fb0000
-#ifdef CONFIG_OMAP_LL_DEBUG_UART3
-		orr	\rx, \rx, #0x00009000	@ UART 3
-#endif
-#if defined(CONFIG_OMAP_LL_DEBUG_UART2) || defined(CONFIG_OMAP_LL_DEBUG_UART3)
-		orr	\rx, \rx, #0x00000800	@ UART 2 & 3
-#endif
+		orr	\rx, \rx, #0x00fb0000	@ OMAP1UART1
+		ldrb	\rx, [\rx, #(UART_SCR << OMAP_PORT_SHIFT)]
+
+		/* Select the UART to use based on the UART1 scratchpad value */
+10:		cmp	\rx, #0			@ no port configured?
+		beq	11f			@ if none, try to use UART1
+		cmp	\rx, #OMAP1UART1
+		beq	11f			@ configure OMAP1UART1
+		cmp	\rx, #OMAP1UART2
+		beq	12f			@ configure OMAP1UART2
+		cmp	\rx, #OMAP1UART3
+		beq	13f			@ configure OMAP2UART3
+
+		/* Configure the UART offset from the phys/virt base */
+11:		mov	\rx, #0x00fb0000	@ OMAP1UART1
+		b	98f
+12:		mov	\rx, #0x00fb0000	@ OMAP1UART1
+		orr	\rx, \rx, #0x00000800	@ OMAP1UART2
+		b	98f
+13:		mov	\rx, #0x00fb0000	@ OMAP1UART1
+		orr	\rx, \rx, #0x00000800	@ OMAP1UART2
+		orr	\rx, \rx, #0x00009000	@ OMAP1UART3
+
+		/* Store both phys and virt address for the uart */
+98:		add	\rx, \rx, #0xff000000	@ phys base
+		ldr	\tmp, =omap_uart_phys
+		str	\rx, [\tmp, #0]
+		sub	\rx, \rx, #0xff000000	@ phys base
+		add	\rx, \rx, #0xfe000000	@ virt base
+		ldr	\tmp, =omap_uart_virt
+		str	\rx, [\tmp, #0]
+		b	9b
+99:
 		.endm
 
 		.macro	senduart,rd,rx