Merge 3.3-rc6 into driver-core-next

This was done to resolve a conflict in the drivers/base/cpu.c file.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

3 files changed, 25 insertions, 16 deletions

diff --git a/drivers/usb/core/hcd-pci.c b/drivers/usb/core/hcd-pci.c
index d136b8f4c8a..81e2c0d9c17 100644
--- a/drivers/usb/core/hcd-pci.c
+++ b/drivers/usb/core/hcd-pci.c
@@ -187,7 +187,10 @@ int usb_hcd_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 		return -ENODEV;
 	dev->current_state = PCI_D0;
 
-	if (!dev->irq) {
+	/* The xHCI driver supports MSI and MSI-X,
+	 * so don't fail if the BIOS doesn't provide a legacy IRQ.
+	 */
+	if (!dev->irq && (driver->flags & HCD_MASK) != HCD_USB3) {
 		dev_err(&dev->dev,
 			"Found HC with no IRQ.  Check BIOS/PCI %s setup!\n",
 			pci_name(dev));
diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index eb19cba34ac..e1282328fc2 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -2447,8 +2447,10 @@ int usb_add_hcd(struct usb_hcd *hcd,
 			&& device_can_wakeup(&hcd->self.root_hub->dev))
 		dev_dbg(hcd->self.controller, "supports USB remote wakeup\n");
 
-	/* enable irqs just before we start the controller */
-	if (usb_hcd_is_primary_hcd(hcd)) {
+	/* enable irqs just before we start the controller,
+	 * if the BIOS provides legacy PCI irqs.
+	 */
+	if (usb_hcd_is_primary_hcd(hcd) && irqnum) {
 		retval = usb_hcd_request_irqs(hcd, irqnum, irqflags);
 		if (retval)
 			goto err_request_irq;
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index a0613d8f9be..265c2f675d0 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -705,10 +705,26 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 	if (type == HUB_INIT3)
 		goto init3;
 
-	/* After a resume, port power should still be on.
+	/* The superspeed hub except for root hub has to use Hub Depth
+	 * value as an offset into the route string to locate the bits
+	 * it uses to determine the downstream port number. So hub driver
+	 * should send a set hub depth request to superspeed hub after
+	 * the superspeed hub is set configuration in initialization or
+	 * reset procedure.
+	 *
+	 * After a resume, port power should still be on.
 	 * For any other type of activation, turn it on.
 	 */
 	if (type != HUB_RESUME) {
+		if (hdev->parent && hub_is_superspeed(hdev)) {
+			ret = usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
+					HUB_SET_DEPTH, USB_RT_HUB,
+					hdev->level - 1, 0, NULL, 0,
+					USB_CTRL_SET_TIMEOUT);
+			if (ret < 0)
+				dev_err(hub->intfdev,
+						"set hub depth failed\n");
+		}
 
 		/* Speed up system boot by using a delayed_work for the
 		 * hub's initial power-up delays.  This is pretty awkward
@@ -987,18 +1003,6 @@ static int hub_configure(struct usb_hub *hub,
 		goto fail;
 	}
 
-	if (hub_is_superspeed(hdev) && (hdev->parent != NULL)) {
-		ret = usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
-				HUB_SET_DEPTH, USB_RT_HUB,
-				hdev->level - 1, 0, NULL, 0,
-				USB_CTRL_SET_TIMEOUT);
-
-		if (ret < 0) {
-			message = "can't set hub depth";
-			goto fail;
-		}
-	}
-
 	/* Request the entire hub descriptor.
 	 * hub->descriptor can handle USB_MAXCHILDREN ports,
 	 * but the hub can/will return fewer bytes here.