diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/3c509.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/cxgb.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/dl2k.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/dmfe.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/operstates.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/packet_mmap.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/pktgen.txt | 4 |
7 files changed, 8 insertions, 8 deletions
diff --git a/Documentation/networking/3c509.txt b/Documentation/networking/3c509.txt index 867a99f88c6..0643e3b7168 100644 --- a/Documentation/networking/3c509.txt +++ b/Documentation/networking/3c509.txt @@ -126,7 +126,7 @@ packets faster than they can be removed from the card. This should be rare or impossible in normal operation. Possible causes of this error report are: - a "green" mode enabled that slows the processor down when there is no - keyboard activitiy. + keyboard activity. - some other device or device driver hogging the bus or disabling interrupts. Check /proc/interrupts for excessive interrupt counts. The timer tick diff --git a/Documentation/networking/cxgb.txt b/Documentation/networking/cxgb.txt index 76324638626..7b231752f25 100644 --- a/Documentation/networking/cxgb.txt +++ b/Documentation/networking/cxgb.txt @@ -56,7 +56,7 @@ FEATURES ethtool -C eth0 rx-usecs 100 - You may also provide a timer latency value while disabling adpative-rx: + You may also provide a timer latency value while disabling adaptive-rx: ethtool -C <interface> adaptive-rx off rx-usecs <microseconds> diff --git a/Documentation/networking/dl2k.txt b/Documentation/networking/dl2k.txt index d460492037e..a3a3c6e08ce 100644 --- a/Documentation/networking/dl2k.txt +++ b/Documentation/networking/dl2k.txt @@ -173,7 +173,7 @@ Installing the Driver Parameter Description ===================== -You can install this driver without any addtional parameter. However, if you +You can install this driver without any additional parameter. However, if you are going to have extensive functions then it is necessary to set extra parameter. Below is a list of the command line parameters supported by the Linux device diff --git a/Documentation/networking/dmfe.txt b/Documentation/networking/dmfe.txt index 046363552d0..b1b7499dd9d 100644 --- a/Documentation/networking/dmfe.txt +++ b/Documentation/networking/dmfe.txt @@ -34,7 +34,7 @@ Next you should configure your network interface with a command similar to : ifconfig eth0 172.22.3.18 ^^^^^^^^^^^ - Your IP Adress + Your IP Address Then you may have to modify the default routing table with command : diff --git a/Documentation/networking/operstates.txt b/Documentation/networking/operstates.txt index 4a21d9bb836..c9074f9b78b 100644 --- a/Documentation/networking/operstates.txt +++ b/Documentation/networking/operstates.txt @@ -2,7 +2,7 @@ 1. Introduction Linux distinguishes between administrative and operational state of an -interface. Admininstrative state is the result of "ip link set dev +interface. Administrative state is the result of "ip link set dev <dev> up or down" and reflects whether the administrator wants to use the device for traffic. diff --git a/Documentation/networking/packet_mmap.txt b/Documentation/networking/packet_mmap.txt index aaf99d5f0da..781626261e3 100644 --- a/Documentation/networking/packet_mmap.txt +++ b/Documentation/networking/packet_mmap.txt @@ -296,7 +296,7 @@ the following (from include/linux/if_packet.h): - struct tpacket_hdr - pad to TPACKET_ALIGNMENT=16 - struct sockaddr_ll - - Gap, chosen so that packet data (Start+tp_net) alignes to + - Gap, chosen so that packet data (Start+tp_net) aligns to TPACKET_ALIGNMENT=16 - Start+tp_mac: [ Optional MAC header ] - Start+tp_net: Packet data, aligned to TPACKET_ALIGNMENT=16. diff --git a/Documentation/networking/pktgen.txt b/Documentation/networking/pktgen.txt index 18d385c068f..c2f859f7f2f 100644 --- a/Documentation/networking/pktgen.txt +++ b/Documentation/networking/pktgen.txt @@ -7,7 +7,7 @@ Date: 041221 Enable CONFIG_NET_PKTGEN to compile and build pktgen.o either in kernel or as module. Module is preferred. insmod pktgen if needed. Once running -pktgen creates a thread on each CPU where each thread has affinty it's CPU. +pktgen creates a thread on each CPU where each thread has affinity to its CPU. Monitoring and controlling is done via /proc. Easiest to select a suitable a sample script and configure. @@ -32,7 +32,7 @@ Running: Stopped: eth1 Result: OK: max_before_softirq=10000 -Most important the devices assigend to thread. Note! A device can only belong +Most important the devices assigned to thread. Note! A device can only belong to one thread. |