diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio-omap.txt | 36 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/sodaville.txt | 48 | ||||
| -rw-r--r-- | Documentation/gpio.txt | 40 |
3 files changed, 119 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/Documentation/devicetree/bindings/gpio/gpio-omap.txt new file mode 100644 index 00000000000..bff51a2fee1 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-omap.txt @@ -0,0 +1,36 @@ +OMAP GPIO controller bindings + +Required properties: +- compatible: + - "ti,omap2-gpio" for OMAP2 controllers + - "ti,omap3-gpio" for OMAP3 controllers + - "ti,omap4-gpio" for OMAP4 controllers +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +OMAP specific properties: +- ti,hwmods: Name of the hwmod associated to the GPIO: + "gpio<X>", <X> being the 1-based instance number from the HW spec + + +Example: + +gpio4: gpio4 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio4"; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/sodaville.txt b/Documentation/devicetree/bindings/gpio/sodaville.txt new file mode 100644 index 00000000000..563eff22b97 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/sodaville.txt @@ -0,0 +1,48 @@ +GPIO controller on CE4100 / Sodaville SoCs +========================================== + +The bindings for CE4100's GPIO controller match the generic description +which is covered by the gpio.txt file in this folder. + +The only additional property is the intel,muxctl property which holds the +value which is written into the MUXCNTL register. + +There is no compatible property for now because the driver is probed via +PCI id (vendor 0x8086 device 0x2e67). + +The interrupt specifier consists of two cells encoded as follows: + - <1st cell>: The interrupt-number that identifies the interrupt source. + - <2nd cell>: The level-sense information, encoded as follows: + 4 - active high level-sensitive + 8 - active low level-sensitive + +Example of the GPIO device and one user: + + pcigpio: gpio@b,1 { + /* two cells for GPIO and interrupt */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "pci8086,2e67.2", + "pci8086,2e67", + "pciclassff0000", + "pciclassff00"; + + reg = <0x15900 0x0 0x0 0x0 0x0>; + /* Interrupt line of the gpio device */ + interrupts = <15 1>; + /* It is an interrupt and GPIO controller itself */ + interrupt-controller; + gpio-controller; + intel,muxctl = <0>; + }; + + testuser@20 { + compatible = "example,testuser"; + /* User the 11th GPIO line as an active high triggered + * level interrupt + */ + interrupts = <11 8>; + interrupt-parent = <&pcigpio>; + /* Use this GPIO also with the gpio functions */ + gpios = <&pcigpio 11 0>; + }; diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt index 792faa3c06c..620a07844e8 100644 --- a/Documentation/gpio.txt +++ b/Documentation/gpio.txt @@ -271,9 +271,26 @@ Some platforms may also use knowledge about what GPIOs are active for power management, such as by powering down unused chip sectors and, more easily, gating off unused clocks. -Note that requesting a GPIO does NOT cause it to be configured in any -way; it just marks that GPIO as in use. Separate code must handle any -pin setup (e.g. controlling which pin the GPIO uses, pullup/pulldown). +For GPIOs that use pins known to the pinctrl subsystem, that subsystem should +be informed of their use; a gpiolib driver's .request() operation may call +pinctrl_request_gpio(), and a gpiolib driver's .free() operation may call +pinctrl_free_gpio(). The pinctrl subsystem allows a pinctrl_request_gpio() +to succeed concurrently with a pin or pingroup being "owned" by a device for +pin multiplexing. + +Any programming of pin multiplexing hardware that is needed to route the +GPIO signal to the appropriate pin should occur within a GPIO driver's +.direction_input() or .direction_output() operations, and occur after any +setup of an output GPIO's value. This allows a glitch-free migration from a +pin's special function to GPIO. This is sometimes required when using a GPIO +to implement a workaround on signals typically driven by a non-GPIO HW block. + +Some platforms allow some or all GPIO signals to be routed to different pins. +Similarly, other aspects of the GPIO or pin may need to be configured, such as +pullup/pulldown. Platform software should arrange that any such details are +configured prior to gpio_request() being called for those GPIOs, e.g. using +the pinctrl subsystem's mapping table, so that GPIO users need not be aware +of these details. Also note that it's your responsibility to have stopped using a GPIO before you free it. @@ -302,6 +319,8 @@ where 'flags' is currently defined to specify the following properties: * GPIOF_INIT_LOW - as output, set initial level to LOW * GPIOF_INIT_HIGH - as output, set initial level to HIGH + * GPIOF_OPEN_DRAIN - gpio pin is open drain type. + * GPIOF_OPEN_SOURCE - gpio pin is open source type. since GPIOF_INIT_* are only valid when configured as output, so group valid combinations as: @@ -310,8 +329,19 @@ combinations as: * GPIOF_OUT_INIT_LOW - configured as output, initial level LOW * GPIOF_OUT_INIT_HIGH - configured as output, initial level HIGH -In the future, these flags can be extended to support more properties such -as open-drain status. +When setting the flag as GPIOF_OPEN_DRAIN then it will assume that pins is +open drain type. Such pins will not be driven to 1 in output mode. It is +require to connect pull-up on such pins. By enabling this flag, gpio lib will +make the direction to input when it is asked to set value of 1 in output mode +to make the pin HIGH. The pin is make to LOW by driving value 0 in output mode. + +When setting the flag as GPIOF_OPEN_SOURCE then it will assume that pins is +open source type. Such pins will not be driven to 0 in output mode. It is +require to connect pull-down on such pin. By enabling this flag, gpio lib will +make the direction to input when it is asked to set value of 0 in output mode +to make the pin LOW. The pin is make to HIGH by driving value 1 in output mode. + +In the future, these flags can be extended to support more properties. Further more, to ease the claim/release of multiple GPIOs, 'struct gpio' is introduced to encapsulate all three fields as: |