diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/serial/rs485.txt | 31 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/tty/serial/atmel-usart.txt | 27 | ||||
| -rw-r--r-- | Documentation/serial/serial-rs485.txt | 5 |
3 files changed, 63 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/serial/rs485.txt b/Documentation/devicetree/bindings/serial/rs485.txt new file mode 100644 index 00000000000..1e753c69fc8 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/rs485.txt @@ -0,0 +1,31 @@ +* RS485 serial communications + +The RTS signal is capable of automatically controlling line direction for +the built-in half-duplex mode. +The properties described hereafter shall be given to a half-duplex capable +UART node. + +Required properties: +- rs485-rts-delay: prop-encoded-array <a b> where: + * a is the delay beteween rts signal and beginning of data sent in milliseconds. + it corresponds to the delay before sending data. + * b is the delay between end of data sent and rts signal in milliseconds + it corresponds to the delay after sending data and actual release of the line. + +Optional properties: +- linux,rs485-enabled-at-boot-time: empty property telling to enable the rs485 + feature at boot time. It can be disabled later with proper ioctl. +- rs485-rx-during-tx: empty property that enables the receiving of data even + whilst sending data. + +RS485 example for Atmel USART: + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x4000>; + interrupts = <7>; + atmel,use-dma-rx; + atmel,use-dma-tx; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 200>; // in milliseconds + }; + diff --git a/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt b/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt new file mode 100644 index 00000000000..a49d9a1d4cc --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/atmel-usart.txt @@ -0,0 +1,27 @@ +* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) + +Required properties: +- compatible: Should be "atmel,<chip>-usart" + The compatible <chip> indicated will be the first SoC to support an + additional mode or an USART new feature. +- reg: Should contain registers location and length +- interrupts: Should contain interrupt + +Optional properties: +- atmel,use-dma-rx: use of PDC or DMA for receiving data +- atmel,use-dma-tx: use of PDC or DMA for transmitting data + +<chip> compatible description: +- at91rm9200: legacy USART support +- at91sam9260: generic USART implementation for SAM9 SoCs + +Example: + + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x4000>; + interrupts = <7>; + atmel,use-dma-rx; + atmel,use-dma-tx; + }; + diff --git a/Documentation/serial/serial-rs485.txt b/Documentation/serial/serial-rs485.txt index c8878f821d1..079cb3df62c 100644 --- a/Documentation/serial/serial-rs485.txt +++ b/Documentation/serial/serial-rs485.txt @@ -28,6 +28,10 @@ RS485 communications. This data structure is used to set and configure RS485 parameters in the platform data and in ioctls. + The device tree can also provide RS485 boot time parameters (see [2] + for bindings). The driver is in charge of filling this data structure from + the values given by the device tree. + Any driver for devices capable of working both as RS232 and RS485 should provide at least the following ioctls: @@ -121,3 +125,4 @@ 5. REFERENCES [1] include/linux/serial.h + [2] Documentation/devicetree/bindings/serial/rs485.txt |