diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 9 | ||||
| -rw-r--r-- | Documentation/networking/ip-sysctl.txt | 8 | ||||
| -rw-r--r-- | Documentation/sound/alsa/HD-Audio-Models.txt | 5 | ||||
| -rw-r--r-- | Documentation/sound/alsa/HD-Audio.txt | 27 |
4 files changed, 45 insertions, 4 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 736d4560288..e7848a0d99e 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -199,6 +199,10 @@ and is between 256 and 4096 characters. It is defined in the file acpi_display_output=video See above. + acpi_early_pdc_eval [HW,ACPI] Evaluate processor _PDC methods + early. Needed on some platforms to properly + initialize the EC. + acpi_irq_balance [HW,ACPI] ACPI will balance active IRQs default in APIC mode @@ -311,6 +315,11 @@ and is between 256 and 4096 characters. It is defined in the file aic79xx= [HW,SCSI] See Documentation/scsi/aic79xx.txt. + alignment= [KNL,ARM] + Allow the default userspace alignment fault handler + behaviour to be specified. Bit 0 enables warnings, + bit 1 enables fixups, and bit 2 sends a segfault. + amd_iommu= [HW,X86-84] Pass parameters to the AMD IOMMU driver in the system. Possible values are: diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index 006b39dec87..e87f3cdc8a6 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -1074,10 +1074,10 @@ regen_max_retry - INTEGER Default: 5 max_addresses - INTEGER - Number of maximum addresses per interface. 0 disables limitation. - It is recommended not set too large value (or 0) because it would - be too easy way to crash kernel to allow to create too much of - autoconfigured addresses. + Maximum number of autoconfigured addresses per interface. Setting + to zero disables the limitation. It is not recommended to set this + value too large (or to zero) because it would be an easy way to + crash the kernel by allowing too many addresses to be created. Default: 16 disable_ipv6 - BOOLEAN diff --git a/Documentation/sound/alsa/HD-Audio-Models.txt b/Documentation/sound/alsa/HD-Audio-Models.txt index e72cee9e2a7..1d38b0dfba9 100644 --- a/Documentation/sound/alsa/HD-Audio-Models.txt +++ b/Documentation/sound/alsa/HD-Audio-Models.txt @@ -124,6 +124,8 @@ ALC882/883/885/888/889 asus-a7m ASUS A7M macpro MacPro support mb5 Macbook 5,1 + macmini3 Macmini 3,1 + mba21 Macbook Air 2,1 mbp3 Macbook Pro rev3 imac24 iMac 24'' with jack detection imac91 iMac 9,1 @@ -279,13 +281,16 @@ Conexant 5051 laptop Basic Laptop config (default) hp HP Spartan laptop hp-dv6736 HP dv6736 + hp-f700 HP Compaq Presario F700 lenovo-x200 Lenovo X200 laptop + toshiba Toshiba Satellite M300 Conexant 5066 ============= laptop Basic Laptop config (default) dell-laptop Dell laptops olpc-xo-1_5 OLPC XO 1.5 + ideapad Lenovo IdeaPad U150 STAC9200 ======== diff --git a/Documentation/sound/alsa/HD-Audio.txt b/Documentation/sound/alsa/HD-Audio.txt index 6325bec06a7..f4dd3bf99d1 100644 --- a/Documentation/sound/alsa/HD-Audio.txt +++ b/Documentation/sound/alsa/HD-Audio.txt @@ -452,6 +452,33 @@ Similarly, the lines after `[verb]` are parsed as `init_verbs` sysfs entries, and the lines after `[hint]` are parsed as `hints` sysfs entries, respectively. +Another example to override the codec vendor id from 0x12345678 to +0xdeadbeef is like below: +------------------------------------------------------------------------ + [codec] + 0x12345678 0xabcd1234 2 + + [vendor_id] + 0xdeadbeef +------------------------------------------------------------------------ + +In the similar way, you can override the codec subsystem_id via +`[subsystem_id]`, the revision id via `[revision_id]` line. +Also, the codec chip name can be rewritten via `[chip_name]` line. +------------------------------------------------------------------------ + [codec] + 0x12345678 0xabcd1234 2 + + [subsystem_id] + 0xffff1111 + + [revision_id] + 0x10 + + [chip_name] + My-own NEWS-0002 +------------------------------------------------------------------------ + The hd-audio driver reads the file via request_firmware(). Thus, a patch file has to be located on the appropriate firmware path, typically, /lib/firmware. For example, when you pass the option |