diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/hwmon/max16064 | 62 | ||||
| -rw-r--r-- | Documentation/hwmon/max34440 | 79 | ||||
| -rw-r--r-- | Documentation/hwmon/max8688 | 69 | ||||
| -rw-r--r-- | Documentation/hwmon/pmbus | 34 | ||||
| -rw-r--r-- | Documentation/hwmon/smm665 | 8 | ||||
| -rw-r--r-- | Documentation/hwmon/submitting-patches | 109 | ||||
| -rw-r--r-- | Documentation/md.txt | 10 | ||||
| -rw-r--r-- | Documentation/sound/alsa/SB-Live-mixer.txt | 6 |
8 files changed, 344 insertions, 33 deletions
diff --git a/Documentation/hwmon/max16064 b/Documentation/hwmon/max16064 new file mode 100644 index 00000000000..41728999e14 --- /dev/null +++ b/Documentation/hwmon/max16064 @@ -0,0 +1,62 @@ +Kernel driver max16064 +====================== + +Supported chips: + * Maxim MAX16064 + Prefix: 'max16064' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX16064.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX16064 Quad Power-Supply +Controller with Active-Voltage Output Control and PMBus Interface. + +The driver is a client driver to the core PMBus driver. +Please see Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in[1-4]_label "vout[1-4]" +in[1-4]_input Measured voltage. From READ_VOUT register. +in[1-4]_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in[1-4]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[1-4]_lcrit Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register. +in[1-4]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[1-4]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[1-4]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[1-4]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[1-4]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +temp1_input Measured temperature. From READ_TEMPERATURE_1 register. +temp1_max Maximum temperature. From OT_WARN_LIMIT register. +temp1_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp1_max_alarm Chip temperature high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_WARN_LIMIT if TEMP_OT_WARNING + status is set. +temp1_crit_alarm Chip temperature critical high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT + status is set. diff --git a/Documentation/hwmon/max34440 b/Documentation/hwmon/max34440 new file mode 100644 index 00000000000..6c525dd07d5 --- /dev/null +++ b/Documentation/hwmon/max34440 @@ -0,0 +1,79 @@ +Kernel driver max34440 +====================== + +Supported chips: + * Maxim MAX34440 + Prefixes: 'max34440' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34440.pdf + * Maxim MAX34441 + PMBus 5-Channel Power-Supply Manager and Intelligent Fan Controller + Prefixes: 'max34441' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34441.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX34440 PMBus 6-Channel +Power-Supply Manager and MAX34441 PMBus 5-Channel Power-Supply Manager +and Intelligent Fan Controller. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in[1-6]_label "vout[1-6]". +in[1-6]_input Measured voltage. From READ_VOUT register. +in[1-6]_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in[1-6]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[1-6]_lcrit Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register. +in[1-6]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[1-6]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[1-6]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[1-6]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[1-6]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +curr[1-6]_label "iout[1-6]". +curr[1-6]_input Measured current. From READ_IOUT register. +curr[1-6]_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr[1-6]_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr[1-6]_max_alarm Current high alarm. From IOUT_OC_WARNING status. +curr[1-6]_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. + + in6 and curr6 attributes only exist for MAX34440. + +temp[1-8]_input Measured temperatures. From READ_TEMPERATURE_1 register. + temp1 is the chip's internal temperature. temp2..temp5 + are remote I2C temperature sensors. For MAX34441, temp6 + is a remote thermal-diode sensor. For MAX34440, temp6..8 + are remote I2C temperature sensors. +temp[1-8]_max Maximum temperature. From OT_WARN_LIMIT register. +temp[1-8]_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp[1-8]_max_alarm Temperature high alarm. +temp[1-8]_crit_alarm Temperature critical high alarm. + + temp7 and temp8 attributes only exist for MAX34440. diff --git a/Documentation/hwmon/max8688 b/Documentation/hwmon/max8688 new file mode 100644 index 00000000000..0ddd3a41203 --- /dev/null +++ b/Documentation/hwmon/max8688 @@ -0,0 +1,69 @@ +Kernel driver max8688 +===================== + +Supported chips: + * Maxim MAX8688 + Prefix: 'max8688' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX8688.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX8688 Digital Power-Supply +Controller/Monitor with PMBus Interface. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in1_label "vout1" +in1_input Measured voltage. From READ_VOUT register. +in1_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in1_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in1_lcrit Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register. +in1_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in1_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in1_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in1_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in1_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +curr1_label "iout1" +curr1_input Measured current. From READ_IOUT register. +curr1_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr1_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr1_max_alarm Current high alarm. From IOUT_OC_WARN_LIMIT register. +curr1_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. + +temp1_input Measured temperature. From READ_TEMPERATURE_1 register. +temp1_max Maximum temperature. From OT_WARN_LIMIT register. +temp1_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp1_max_alarm Chip temperature high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_WARN_LIMIT if TEMP_OT_WARNING + status is set. +temp1_crit_alarm Chip temperature critical high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT + status is set. diff --git a/Documentation/hwmon/pmbus b/Documentation/hwmon/pmbus index dc4933e9634..5e462fc7f99 100644 --- a/Documentation/hwmon/pmbus +++ b/Documentation/hwmon/pmbus @@ -13,26 +13,6 @@ Supported chips: Prefix: 'ltc2978' Addresses scanned: - Datasheet: http://cds.linear.com/docs/Datasheet/2978fa.pdf - * Maxim MAX16064 - Quad Power-Supply Controller - Prefix: 'max16064' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX16064.pdf - * Maxim MAX34440 - PMBus 6-Channel Power-Supply Manager - Prefixes: 'max34440' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34440.pdf - * Maxim MAX34441 - PMBus 5-Channel Power-Supply Manager and Intelligent Fan Controller - Prefixes: 'max34441' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34441.pdf - * Maxim MAX8688 - Digital Power-Supply Controller/Monitor - Prefix: 'max8688' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX8688.pdf * Generic PMBus devices Prefix: 'pmbus' Addresses scanned: - @@ -175,11 +155,13 @@ currX_crit Critical maximum current. From IIN_OC_FAULT_LIMIT or IOUT_OC_FAULT_LIMIT register. currX_alarm Current high alarm. From IIN_OC_WARNING or IOUT_OC_WARNING status. +currX_max_alarm Current high alarm. + From IIN_OC_WARN_LIMIT or IOUT_OC_WARN_LIMIT status. currX_lcrit_alarm Output current critical low alarm. From IOUT_UC_FAULT status. currX_crit_alarm Current critical high alarm. From IIN_OC_FAULT or IOUT_OC_FAULT status. -currX_label "iin" or "vinY" +currX_label "iin" or "ioutY" powerX_input Measured power. From READ_PIN or READ_POUT register. powerX_cap Output power cap. From POUT_MAX register. @@ -193,13 +175,13 @@ powerX_crit_alarm Output power critical high alarm. From POUT_OP_FAULT status. powerX_label "pin" or "poutY" -tempX_input Measured tempererature. +tempX_input Measured temperature. From READ_TEMPERATURE_X register. -tempX_min Mimimum tempererature. From UT_WARN_LIMIT register. -tempX_max Maximum tempererature. From OT_WARN_LIMIT register. -tempX_lcrit Critical low tempererature. +tempX_min Mimimum temperature. From UT_WARN_LIMIT register. +tempX_max Maximum temperature. From OT_WARN_LIMIT register. +tempX_lcrit Critical low temperature. From UT_FAULT_LIMIT register. -tempX_crit Critical high tempererature. +tempX_crit Critical high temperature. From OT_FAULT_LIMIT register. tempX_min_alarm Chip temperature low alarm. Set by comparing READ_TEMPERATURE_X with UT_WARN_LIMIT if diff --git a/Documentation/hwmon/smm665 b/Documentation/hwmon/smm665 index 3820fc9ca52..59e31614054 100644 --- a/Documentation/hwmon/smm665 +++ b/Documentation/hwmon/smm665 @@ -150,8 +150,8 @@ in8_crit_alarm Channel F critical alarm in9_crit_alarm AIN1 critical alarm in10_crit_alarm AIN2 critical alarm -temp1_input Chip tempererature -temp1_min Mimimum chip tempererature -temp1_max Maximum chip tempererature -temp1_crit Critical chip tempererature +temp1_input Chip temperature +temp1_min Mimimum chip temperature +temp1_max Maximum chip temperature +temp1_crit Critical chip temperature temp1_crit_alarm Temperature critical alarm diff --git a/Documentation/hwmon/submitting-patches b/Documentation/hwmon/submitting-patches new file mode 100644 index 00000000000..86f42e8e9e4 --- /dev/null +++ b/Documentation/hwmon/submitting-patches @@ -0,0 +1,109 @@ + How to Get Your Patch Accepted Into the Hwmon Subsystem + ------------------------------------------------------- + +This text is is a collection of suggestions for people writing patches or +drivers for the hwmon subsystem. Following these suggestions will greatly +increase the chances of your change being accepted. + + +1. General +---------- + +* It should be unnecessary to mention, but please read and follow + Documentation/SubmitChecklist + Documentation/SubmittingDrivers + Documentation/SubmittingPatches + Documentation/CodingStyle + +* If your patch generates checkpatch warnings, please refrain from explanations + such as "I don't like that coding style". Keep in mind that each unnecessary + warning helps hiding a real problem. If you don't like the kernel coding + style, don't write kernel drivers. + +* Please test your patch thoroughly. We are not your test group. + Sometimes a patch can not or not completely be tested because of missing + hardware. In such cases, you should test-build the code on at least one + architecture. If run-time testing was not achieved, it should be written + explicitly below the patch header. + +* If your patch (or the driver) is affected by configuration options such as + CONFIG_SMP or CONFIG_HOTPLUG, make sure it compiles for all configuration + variants. + + +2. Adding functionality to existing drivers +------------------------------------------- + +* Make sure the documentation in Documentation/hwmon/<driver_name> is up to + date. + +* Make sure the information in Kconfig is up to date. + +* If the added functionality requires some cleanup or structural changes, split + your patch into a cleanup part and the actual addition. This makes it easier + to review your changes, and to bisect any resulting problems. + +* Never mix bug fixes, cleanup, and functional enhancements in a single patch. + + +3. New drivers +-------------- + +* Running your patch or driver file(s) through checkpatch does not mean its + formatting is clean. If unsure about formatting in your new driver, run it + through Lindent. Lindent is not perfect, and you may have to do some minor + cleanup, but it is a good start. + +* Consider adding yourself to MAINTAINERS. + +* Document the driver in Documentation/hwmon/<driver_name>. + +* Add the driver to Kconfig and Makefile in alphabetical order. + +* Make sure that all dependencies are listed in Kconfig. For new drivers, it + is most likely prudent to add a dependency on EXPERIMENTAL. + +* Avoid forward declarations if you can. Rearrange the code if necessary. + +* Avoid calculations in macros and macro-generated functions. While such macros + may save a line or so in the source, it obfuscates the code and makes code + review more difficult. It may also result in code which is more complicated + than necessary. Use inline functions or just regular functions instead. + +* If the driver has a detect function, make sure it is silent. Debug messages + and messages printed after a successful detection are acceptable, but it + must not print messages such as "Chip XXX not found/supported". + + Keep in mind that the detect function will run for all drivers supporting an + address if a chip is detected on that address. Unnecessary messages will just + pollute the kernel log and not provide any value. + +* Provide a detect function if and only if a chip can be detected reliably. + +* Avoid writing to chip registers in the detect function. If you have to write, + only do it after you have already gathered enough data to be certain that the + detection is going to be successful. + + Keep in mind that the chip might not be what your driver believes it is, and + writing to it might cause a bad misconfiguration. + +* Make sure there are no race conditions in the probe function. Specifically, + completely initialize your chip first, then create sysfs entries and register + with the hwmon subsystem. + +* Do not provide support for deprecated sysfs attributes. + +* Do not create non-standard attributes unless really needed. If you have to use + non-standard attributes, or you believe you do, discuss it on the mailing list + first. Either case, provide a detailed explanation why you need the + non-standard attribute(s). + Standard attributes are specified in Documentation/hwmon/sysfs-interface. + +* When deciding which sysfs attributes to support, look at the chip's + capabilities. While we do not expect your driver to support everything the + chip may offer, it should at least support all limits and alarms. + +* Last but not least, please check if a driver for your chip already exists + before starting to write a new driver. Especially for temperature sensors, + new chips are often variants of previously released chips. In some cases, + a presumably new chip may simply have been relabeled. diff --git a/Documentation/md.txt b/Documentation/md.txt index a81c7b4790f..2366b1c8cf1 100644 --- a/Documentation/md.txt +++ b/Documentation/md.txt @@ -552,6 +552,16 @@ also have within the array where IO will be blocked. This is currently only supported for raid4/5/6. + sync_min + sync_max + The two values, given as numbers of sectors, indicate a range + withing the array where 'check'/'repair' will operate. Must be + a multiple of chunk_size. When it reaches "sync_max" it will + pause, rather than complete. + You can use 'select' or 'poll' on "sync_completed" to wait for + that number to reach sync_max. Then you can either increase + "sync_max", or can write 'idle' to "sync_action". + Each active md device may also have attributes specific to the personality module that manages it. diff --git a/Documentation/sound/alsa/SB-Live-mixer.txt b/Documentation/sound/alsa/SB-Live-mixer.txt index f5639d40521..f4b5988f450 100644 --- a/Documentation/sound/alsa/SB-Live-mixer.txt +++ b/Documentation/sound/alsa/SB-Live-mixer.txt @@ -87,14 +87,14 @@ accumulator. ALSA uses accumulators 0 and 1 for left and right PCM. The result is forwarded to the ADC capture FIFO (thus to the standard capture PCM device). -name='Music Playback Volume',index=0 +name='Synth Playback Volume',index=0 This control is used to attenuate samples for left and right MIDI FX-bus accumulators. ALSA uses accumulators 4 and 5 for left and right MIDI samples. The result samples are forwarded to the front DAC PCM slots of the AC97 codec. -name='Music Capture Volume',index=0 -name='Music Capture Switch',index=0 +name='Synth Capture Volume',index=0 +name='Synth Capture Switch',index=0 These controls are used to attenuate samples for left and right MIDI FX-bus accumulator. ALSA uses accumulators 4 and 5 for left and right PCM. |