diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-class-net-mesh | 9 | ||||
| -rw-r--r-- | Documentation/networking/batman-adv.txt | 19 | ||||
| -rw-r--r-- | Documentation/networking/stmmac.txt | 29 |
3 files changed, 44 insertions, 13 deletions
diff --git a/Documentation/ABI/testing/sysfs-class-net-mesh b/Documentation/ABI/testing/sysfs-class-net-mesh index b218e0f8bdb..c81fe89c4c4 100644 --- a/Documentation/ABI/testing/sysfs-class-net-mesh +++ b/Documentation/ABI/testing/sysfs-class-net-mesh @@ -14,6 +14,15 @@ Description: mesh will be sent using multiple interfaces at the same time (if available). +What: /sys/class/net/<mesh_iface>/mesh/bridge_loop_avoidance +Date: November 2011 +Contact: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> +Description: + Indicates whether the bridge loop avoidance feature + is enabled. This feature detects and avoids loops + between the mesh and devices bridged with the soft + interface <mesh_iface>. + What: /sys/class/net/<mesh_iface>/mesh/fragmentation Date: October 2010 Contact: Andreas Langer <an.langer@gmx.de> diff --git a/Documentation/networking/batman-adv.txt b/Documentation/networking/batman-adv.txt index 221ad0cdf11..220a58c2fb1 100644 --- a/Documentation/networking/batman-adv.txt +++ b/Documentation/networking/batman-adv.txt @@ -67,18 +67,18 @@ To deactivate an interface you have to write "none" into its All mesh wide settings can be found in batman's own interface folder: -# ls /sys/class/net/bat0/mesh/ -# aggregated_ogms fragmentation gw_sel_class vis_mode -# ap_isolation gw_bandwidth hop_penalty -# bonding gw_mode orig_interval +# ls /sys/class/net/bat0/mesh/ +# aggregated_ogms fragmentation hop_penalty +# ap_isolation gw_bandwidth log_level +# bonding gw_mode orig_interval +# bridge_loop_avoidance gw_sel_class vis_mode There is a special folder for debugging information: # ls /sys/kernel/debug/batman_adv/bat0/ -# gateways socket transtable_global vis_data -# originators softif_neigh transtable_local - +# bla_claim_table log socket transtable_local +# gateways originators transtable_global vis_data Some of the files contain all sort of status information regard- ing the mesh network. For example, you can view the table of @@ -202,12 +202,13 @@ abled during run time. Following log_levels are defined: 1 - Enable messages related to routing / flooding / broadcasting 2 - Enable messages related to route added / changed / deleted 4 - Enable messages related to translation table operations -7 - Enable all messages +8 - Enable messages related to bridge loop avoidance +15 - enable all messages The debug output can be changed at runtime using the file /sys/class/net/bat0/mesh/log_level. e.g. -# echo 2 > /sys/class/net/bat0/mesh/log_level +# echo 6 > /sys/class/net/bat0/mesh/log_level will enable debug messages for when routes change. diff --git a/Documentation/networking/stmmac.txt b/Documentation/networking/stmmac.txt index d0aeeadd264..ab1e8d7004c 100644 --- a/Documentation/networking/stmmac.txt +++ b/Documentation/networking/stmmac.txt @@ -111,11 +111,12 @@ and detailed below as well: int phy_addr; int interface; struct stmmac_mdio_bus_data *mdio_bus_data; - int pbl; + struct stmmac_dma_cfg *dma_cfg; int clk_csr; int has_gmac; int enh_desc; int tx_coe; + int rx_coe; int bugged_jumbo; int pmt; int force_sf_dma_mode; @@ -136,10 +137,12 @@ Where: o pbl: the Programmable Burst Length is maximum number of beats to be transferred in one DMA transaction. GMAC also enables the 4xPBL by default. - o clk_csr: CSR Clock range selection. + o clk_csr: fixed CSR Clock range selection. o has_gmac: uses the GMAC core. o enh_desc: if sets the MAC will use the enhanced descriptor structure. o tx_coe: core is able to perform the tx csum in HW. + o rx_coe: the supports three check sum offloading engine types: + type_1, type_2 (full csum) and no RX coe. o bugged_jumbo: some HWs are not able to perform the csum in HW for over-sized frames due to limited buffer sizes. Setting this flag the csum will be done in SW on @@ -160,7 +163,7 @@ Where: o custom_cfg: this is a custom configuration that can be passed while initialising the resources. -The we have: +For MDIO bus The we have: struct stmmac_mdio_bus_data { int bus_id; @@ -177,10 +180,28 @@ Where: o irqs: list of IRQs, one per PHY. o probed_phy_irq: if irqs is NULL, use this for probed PHY. + +For DMA engine we have the following internal fields that should be +tuned according to the HW capabilities. + +struct stmmac_dma_cfg { + int pbl; + int fixed_burst; + int burst_len_supported; +}; + +Where: + o pbl: Programmable Burst Length + o fixed_burst: program the DMA to use the fixed burst mode + o burst_len: this is the value we put in the register + supported values are provided as macros in + linux/stmmac.h header file. + +--- + Below an example how the structures above are using on ST platforms. static struct plat_stmmacenet_data stxYYY_ethernet_platform_data = { - .pbl = 32, .has_gmac = 0, .enh_desc = 0, .fix_mac_speed = stxYYY_ethernet_fix_mac_speed, |