diff options
Diffstat (limited to 'arch/arm/mach-pxa')
| -rw-r--r-- | arch/arm/mach-pxa/cm-x2xx.c | 3 | ||||
| -rw-r--r-- | arch/arm/mach-pxa/include/mach/memory.h | 4 | ||||
| -rw-r--r-- | arch/arm/mach-pxa/mfp-pxa2xx.c | 4 | ||||
| -rw-r--r-- | arch/arm/mach-pxa/raumfeld.c | 36 |
4 files changed, 24 insertions, 23 deletions
diff --git a/arch/arm/mach-pxa/cm-x2xx.c b/arch/arm/mach-pxa/cm-x2xx.c index a1099678247..bc55d07566c 100644 --- a/arch/arm/mach-pxa/cm-x2xx.c +++ b/arch/arm/mach-pxa/cm-x2xx.c @@ -518,4 +518,7 @@ MACHINE_START(ARMCORE, "Compulab CM-X2XX") .init_irq = cmx2xx_init_irq, .timer = &pxa_timer, .init_machine = cmx2xx_init, +#ifdef CONFIG_PCI + .dma_zone_size = SZ_64M, +#endif MACHINE_END diff --git a/arch/arm/mach-pxa/include/mach/memory.h b/arch/arm/mach-pxa/include/mach/memory.h index 07734f37f8f..d05a59727d6 100644 --- a/arch/arm/mach-pxa/include/mach/memory.h +++ b/arch/arm/mach-pxa/include/mach/memory.h @@ -17,8 +17,4 @@ */ #define PLAT_PHYS_OFFSET UL(0xa0000000) -#if defined(CONFIG_MACH_ARMCORE) && defined(CONFIG_PCI) -#define ARM_DMA_ZONE_SIZE SZ_64M -#endif - #endif diff --git a/arch/arm/mach-pxa/mfp-pxa2xx.c b/arch/arm/mach-pxa/mfp-pxa2xx.c index 87ae3129f4f..b27544bcafc 100644 --- a/arch/arm/mach-pxa/mfp-pxa2xx.c +++ b/arch/arm/mach-pxa/mfp-pxa2xx.c @@ -347,9 +347,9 @@ static int pxa2xx_mfp_suspend(void) if ((gpio_desc[i].config & MFP_LPM_KEEP_OUTPUT) && (GPDR(i) & GPIO_bit(i))) { if (GPLR(i) & GPIO_bit(i)) - PGSR(i) |= GPIO_bit(i); + PGSR(gpio_to_bank(i)) |= GPIO_bit(i); else - PGSR(i) &= ~GPIO_bit(i); + PGSR(gpio_to_bank(i)) &= ~GPIO_bit(i); } } diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c index d130f77b6d1..2f37d43f51b 100644 --- a/arch/arm/mach-pxa/raumfeld.c +++ b/arch/arm/mach-pxa/raumfeld.c @@ -573,10 +573,10 @@ static struct pxafb_mode_info sharp_lq043t3dx02_mode = { .xres = 480, .yres = 272, .bpp = 16, - .hsync_len = 4, + .hsync_len = 41, .left_margin = 2, .right_margin = 1, - .vsync_len = 1, + .vsync_len = 10, .upper_margin = 3, .lower_margin = 1, .sync = 0, @@ -596,29 +596,31 @@ static void __init raumfeld_lcd_init(void) { int ret; - pxa_set_fb_info(NULL, &raumfeld_sharp_lcd_info); - - /* Earlier devices had the backlight regulator controlled - * via PWM, later versions use another controller for that */ - if ((system_rev & 0xff) < 2) { - mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT; - pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1); - platform_device_register(&raumfeld_pwm_backlight_device); - } else - platform_device_register(&raumfeld_lt3593_device); - ret = gpio_request(GPIO_TFT_VA_EN, "display VA enable"); if (ret < 0) pr_warning("Unable to request GPIO_TFT_VA_EN\n"); else gpio_direction_output(GPIO_TFT_VA_EN, 1); + msleep(100); + ret = gpio_request(GPIO_DISPLAY_ENABLE, "display enable"); if (ret < 0) pr_warning("Unable to request GPIO_DISPLAY_ENABLE\n"); else gpio_direction_output(GPIO_DISPLAY_ENABLE, 1); + /* Hardware revision 2 has the backlight regulator controlled + * by an LT3593, earlier and later devices use PWM for that. */ + if ((system_rev & 0xff) == 2) { + platform_device_register(&raumfeld_lt3593_device); + } else { + mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT; + pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1); + platform_device_register(&raumfeld_pwm_backlight_device); + } + + pxa_set_fb_info(NULL, &raumfeld_sharp_lcd_info); platform_device_register(&pxa3xx_device_gcu); } @@ -657,10 +659,10 @@ static struct lis3lv02d_platform_data lis3_pdata = { #define SPI_AK4104 \ { \ - .modalias = "ak4104", \ - .max_speed_hz = 10000, \ - .bus_num = 0, \ - .chip_select = 0, \ + .modalias = "ak4104-codec", \ + .max_speed_hz = 10000, \ + .bus_num = 0, \ + .chip_select = 0, \ .controller_data = (void *) GPIO_SPDIF_CS, \ } |