diff options
Diffstat (limited to 'arch/avr32/boards/atngw100/setup.c')
| -rw-r--r-- | arch/avr32/boards/atngw100/setup.c | 120 |
1 files changed, 112 insertions, 8 deletions
diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c index 5b022aad4bd..8c6a2440e34 100644 --- a/arch/avr32/boards/atngw100/setup.c +++ b/arch/avr32/boards/atngw100/setup.c @@ -20,6 +20,7 @@ #include <linux/leds.h> #include <linux/spi/spi.h> #include <linux/atmel-mci.h> +#include <linux/usb/atmel_usba_udc.h> #include <asm/io.h> #include <asm/setup.h> @@ -36,6 +37,75 @@ unsigned long at32_board_osc_rates[3] = { [2] = 12000000, /* 12 MHz on osc1 */ }; +/* + * The ATNGW100 mkII is very similar to the ATNGW100. Both have the AT32AP7000 + * chip on board; the difference is that the ATNGW100 mkII has 128 MB 32-bit + * SDRAM (the ATNGW100 has 32 MB 16-bit SDRAM) and 256 MB 16-bit NAND flash + * (the ATNGW100 has none.) + * + * The RAM difference is handled by the boot loader, so the only difference we + * end up handling here is the NAND flash, EBI pin reservation and if LCDC or + * MACB1 should be enabled. + */ +#ifdef CONFIG_BOARD_ATNGW100_MKII +#include <linux/mtd/partitions.h> +#include <mach/smc.h> + +static struct smc_timing nand_timing __initdata = { + .ncs_read_setup = 0, + .nrd_setup = 10, + .ncs_write_setup = 0, + .nwe_setup = 10, + + .ncs_read_pulse = 30, + .nrd_pulse = 15, + .ncs_write_pulse = 30, + .nwe_pulse = 15, + + .read_cycle = 30, + .write_cycle = 30, + + .ncs_read_recover = 0, + .nrd_recover = 15, + .ncs_write_recover = 0, + /* WE# high -> RE# low min 60 ns */ + .nwe_recover = 50, +}; + +static struct smc_config nand_config __initdata = { + .bus_width = 2, + .nrd_controlled = 1, + .nwe_controlled = 1, + .nwait_mode = 0, + .byte_write = 0, + .tdf_cycles = 2, + .tdf_mode = 0, +}; + +static struct mtd_partition nand_partitions[] = { + { + .name = "main", + .offset = 0x00000000, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_part_info(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(nand_partitions); + return nand_partitions; +} + +static struct atmel_nand_data atngw100mkii_nand_data __initdata = { + .cle = 21, + .ale = 22, + .rdy_pin = GPIO_PIN_PB(28), + .enable_pin = GPIO_PIN_PE(23), + .bus_width_16 = true, + .partition_info = nand_part_info, +}; +#endif + /* Initialized by bootloader-specific startup code. */ struct tag *bootloader_tags __initdata; @@ -56,11 +126,24 @@ static struct spi_board_info spi0_board_info[] __initdata = { static struct mci_platform_data __initdata mci0_data = { .slot[0] = { .bus_width = 4, +#if defined(CONFIG_BOARD_ATNGW100_MKII) + .detect_pin = GPIO_PIN_PC(25), + .wp_pin = GPIO_PIN_PE(22), +#else .detect_pin = GPIO_PIN_PC(25), .wp_pin = GPIO_PIN_PE(0), +#endif }, }; +static struct usba_platform_data atngw100_usba_data __initdata = { +#if defined(CONFIG_BOARD_ATNGW100_MKII) + .vbus_pin = GPIO_PIN_PE(26), +#else + .vbus_pin = -ENODEV, +#endif +}; + /* * The next two functions should go away as the boot loader is * supposed to initialize the macb address registers with a valid @@ -168,18 +251,27 @@ static int __init atngw100_init(void) unsigned i; /* - * ATNGW100 uses 16-bit SDRAM interface, so we don't need to - * reserve any pins for it. + * ATNGW100 mkII uses 32-bit SDRAM interface. Reserve the + * SDRAM-specific pins so that nobody messes with them. */ +#ifdef CONFIG_BOARD_ATNGW100_MKII + at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL); + + smc_set_timing(&nand_config, &nand_timing); + smc_set_configuration(3, &nand_config); + at32_add_device_nand(0, &atngw100mkii_nand_data); +#endif at32_add_device_usart(0); set_hw_addr(at32_add_device_eth(0, ð_data[0])); +#ifndef CONFIG_BOARD_ATNGW100_MKII_LCD set_hw_addr(at32_add_device_eth(1, ð_data[1])); +#endif at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); at32_add_device_mci(0, &mci0_data); - at32_add_device_usba(0, NULL); + at32_add_device_usba(0, &atngw100_usba_data); for (i = 0; i < ARRAY_SIZE(ngw_leds); i++) { at32_select_gpio(ngw_leds[i].gpio, @@ -189,10 +281,14 @@ static int __init atngw100_init(void) /* all these i2c/smbus pins should have external pullups for * open-drain sharing among all I2C devices. SDA and SCL do; - * PB28/EXTINT3 doesn't; it should be SMBALERT# (for PMBus), - * but it's not available off-board. + * PB28/EXTINT3 (ATNGW100) and PE21 (ATNGW100 mkII) doesn't; it should + * be SMBALERT# (for PMBus), but it's not available off-board. */ +#ifdef CONFIG_BOARD_ATNGW100_MKII + at32_select_periph(GPIO_PIOE_BASE, 1 << 21, 0, AT32_GPIOF_PULLUP); +#else at32_select_periph(GPIO_PIOB_BASE, 1 << 28, 0, AT32_GPIOF_PULLUP); +#endif at32_select_gpio(i2c_gpio_data.sda_pin, AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH); at32_select_gpio(i2c_gpio_data.scl_pin, @@ -206,14 +302,22 @@ postcore_initcall(atngw100_init); static int __init atngw100_arch_init(void) { - /* PB30 is the otherwise unused jumper on the mainboard, with an - * external pullup; the jumper grounds it. Use it however you - * like, including letting U-Boot or Linux tweak boot sequences. + /* PB30 (ATNGW100) and PE30 (ATNGW100 mkII) is the otherwise unused + * jumper on the mainboard, with an external pullup; the jumper grounds + * it. Use it however you like, including letting U-Boot or Linux tweak + * boot sequences. */ +#ifdef CONFIG_BOARD_ATNGW100_MKII + at32_select_gpio(GPIO_PIN_PE(30), 0); + gpio_request(GPIO_PIN_PE(30), "j15"); + gpio_direction_input(GPIO_PIN_PE(30)); + gpio_export(GPIO_PIN_PE(30), false); +#else at32_select_gpio(GPIO_PIN_PB(30), 0); gpio_request(GPIO_PIN_PB(30), "j15"); gpio_direction_input(GPIO_PIN_PB(30)); gpio_export(GPIO_PIN_PB(30), false); +#endif /* set_irq_type() after the arch_initcall for EIC has run, and * before the I2C subsystem could try using this IRQ. |